* [PATCH V3] regulator: da9061/62: Adjust LDO voltage selection minimum value
@ 2019-06-19 16:35 Steve Twiss
2019-06-19 16:55 ` Mark Brown
0 siblings, 1 reply; 2+ messages in thread
From: Steve Twiss @ 2019-06-19 16:35 UTC (permalink / raw)
To: Liam Girdwood, Mark Brown, Lee Jones, Felix Riemann
Cc: Support Opensource, LKML
From: Felix Riemann <felix.riemann@sma.de>
According to the DA9061 and DA9062 datasheets the LDO voltage selection
registers have a lower value of 0x02. This applies to voltage registers
VLDO1_A, VLDO2_A, VLDO3_A and VLDO4_A. This linear offset of 0x02 was
previously not observed by the driver, causing the LDO output voltage to
be systematically lower by two steps (= 0.1V).
This patch fixes the minimum linear selector offset by setting it to a
value of 2 and increases the n_voltages by the same amount allowing
voltages in the range 0x02 -> 0.9V to 0x38 -> 3.6V to be correctly
selected. Also fixes an incorrect calculaton for the n_voltages value in
the regulator LDO2.
These fixes effect all LDO regulators for DA9061 and DA9062.
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Felix Riemann <felix.riemann@sma.de>
---
Hi Mark,
I've added my signed-off tag to the commit patch of V3.
Regards,
Steve
drivers/regulator/da9062-regulator.c | 40 +++++++++++++++++++++---------------
include/linux/mfd/da9062/registers.h | 3 +++
2 files changed, 27 insertions(+), 16 deletions(-)
diff --git a/drivers/regulator/da9062-regulator.c b/drivers/regulator/da9062-regulator.c
index a02e048..1cadaae 100644
--- a/drivers/regulator/da9062-regulator.c
+++ b/drivers/regulator/da9062-regulator.c
@@ -493,12 +493,13 @@ static int da9062_ldo_set_suspend_mode(struct regulator_dev *rdev,
.desc.ops = &da9062_ldo_ops,
.desc.min_uV = (900) * 1000,
.desc.uV_step = (50) * 1000,
- .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1
+ + DA9062AA_VLDO_A_MIN_SEL,
.desc.enable_reg = DA9062AA_LDO1_CONT,
.desc.enable_mask = DA9062AA_LDO1_EN_MASK,
.desc.vsel_reg = DA9062AA_VLDO1_A,
.desc.vsel_mask = DA9062AA_VLDO1_A_MASK,
- .desc.linear_min_sel = 0,
+ .desc.linear_min_sel = DA9062AA_VLDO_A_MIN_SEL,
.sleep = REG_FIELD(DA9062AA_VLDO1_A,
__builtin_ffs((int)DA9062AA_LDO1_SL_A_MASK) - 1,
sizeof(unsigned int) * 8 -
@@ -525,12 +526,13 @@ static int da9062_ldo_set_suspend_mode(struct regulator_dev *rdev,
.desc.ops = &da9062_ldo_ops,
.desc.min_uV = (900) * 1000,
.desc.uV_step = (50) * 1000,
- .desc.n_voltages = ((3600) - (600))/(50) + 1,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1
+ + DA9062AA_VLDO_A_MIN_SEL,
.desc.enable_reg = DA9062AA_LDO2_CONT,
.desc.enable_mask = DA9062AA_LDO2_EN_MASK,
.desc.vsel_reg = DA9062AA_VLDO2_A,
.desc.vsel_mask = DA9062AA_VLDO2_A_MASK,
- .desc.linear_min_sel = 0,
+ .desc.linear_min_sel = DA9062AA_VLDO_A_MIN_SEL,
.sleep = REG_FIELD(DA9062AA_VLDO2_A,
__builtin_ffs((int)DA9062AA_LDO2_SL_A_MASK) - 1,
sizeof(unsigned int) * 8 -
@@ -557,12 +559,13 @@ static int da9062_ldo_set_suspend_mode(struct regulator_dev *rdev,
.desc.ops = &da9062_ldo_ops,
.desc.min_uV = (900) * 1000,
.desc.uV_step = (50) * 1000,
- .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1
+ + DA9062AA_VLDO_A_MIN_SEL,
.desc.enable_reg = DA9062AA_LDO3_CONT,
.desc.enable_mask = DA9062AA_LDO3_EN_MASK,
.desc.vsel_reg = DA9062AA_VLDO3_A,
.desc.vsel_mask = DA9062AA_VLDO3_A_MASK,
- .desc.linear_min_sel = 0,
+ .desc.linear_min_sel = DA9062AA_VLDO_A_MIN_SEL,
.sleep = REG_FIELD(DA9062AA_VLDO3_A,
__builtin_ffs((int)DA9062AA_LDO3_SL_A_MASK) - 1,
sizeof(unsigned int) * 8 -
@@ -589,12 +592,13 @@ static int da9062_ldo_set_suspend_mode(struct regulator_dev *rdev,
.desc.ops = &da9062_ldo_ops,
.desc.min_uV = (900) * 1000,
.desc.uV_step = (50) * 1000,
- .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1
+ + DA9062AA_VLDO_A_MIN_SEL,
.desc.enable_reg = DA9062AA_LDO4_CONT,
.desc.enable_mask = DA9062AA_LDO4_EN_MASK,
.desc.vsel_reg = DA9062AA_VLDO4_A,
.desc.vsel_mask = DA9062AA_VLDO4_A_MASK,
- .desc.linear_min_sel = 0,
+ .desc.linear_min_sel = DA9062AA_VLDO_A_MIN_SEL,
.sleep = REG_FIELD(DA9062AA_VLDO4_A,
__builtin_ffs((int)DA9062AA_LDO4_SL_A_MASK) - 1,
sizeof(unsigned int) * 8 -
@@ -769,12 +773,13 @@ static int da9062_ldo_set_suspend_mode(struct regulator_dev *rdev,
.desc.ops = &da9062_ldo_ops,
.desc.min_uV = (900) * 1000,
.desc.uV_step = (50) * 1000,
- .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1
+ + DA9062AA_VLDO_A_MIN_SEL,
.desc.enable_reg = DA9062AA_LDO1_CONT,
.desc.enable_mask = DA9062AA_LDO1_EN_MASK,
.desc.vsel_reg = DA9062AA_VLDO1_A,
.desc.vsel_mask = DA9062AA_VLDO1_A_MASK,
- .desc.linear_min_sel = 0,
+ .desc.linear_min_sel = DA9062AA_VLDO_A_MIN_SEL,
.sleep = REG_FIELD(DA9062AA_VLDO1_A,
__builtin_ffs((int)DA9062AA_LDO1_SL_A_MASK) - 1,
sizeof(unsigned int) * 8 -
@@ -801,12 +806,13 @@ static int da9062_ldo_set_suspend_mode(struct regulator_dev *rdev,
.desc.ops = &da9062_ldo_ops,
.desc.min_uV = (900) * 1000,
.desc.uV_step = (50) * 1000,
- .desc.n_voltages = ((3600) - (600))/(50) + 1,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1
+ + DA9062AA_VLDO_A_MIN_SEL,
.desc.enable_reg = DA9062AA_LDO2_CONT,
.desc.enable_mask = DA9062AA_LDO2_EN_MASK,
.desc.vsel_reg = DA9062AA_VLDO2_A,
.desc.vsel_mask = DA9062AA_VLDO2_A_MASK,
- .desc.linear_min_sel = 0,
+ .desc.linear_min_sel = DA9062AA_VLDO_A_MIN_SEL,
.sleep = REG_FIELD(DA9062AA_VLDO2_A,
__builtin_ffs((int)DA9062AA_LDO2_SL_A_MASK) - 1,
sizeof(unsigned int) * 8 -
@@ -833,12 +839,13 @@ static int da9062_ldo_set_suspend_mode(struct regulator_dev *rdev,
.desc.ops = &da9062_ldo_ops,
.desc.min_uV = (900) * 1000,
.desc.uV_step = (50) * 1000,
- .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1
+ + DA9062AA_VLDO_A_MIN_SEL,
.desc.enable_reg = DA9062AA_LDO3_CONT,
.desc.enable_mask = DA9062AA_LDO3_EN_MASK,
.desc.vsel_reg = DA9062AA_VLDO3_A,
.desc.vsel_mask = DA9062AA_VLDO3_A_MASK,
- .desc.linear_min_sel = 0,
+ .desc.linear_min_sel = DA9062AA_VLDO_A_MIN_SEL,
.sleep = REG_FIELD(DA9062AA_VLDO3_A,
__builtin_ffs((int)DA9062AA_LDO3_SL_A_MASK) - 1,
sizeof(unsigned int) * 8 -
@@ -865,12 +872,13 @@ static int da9062_ldo_set_suspend_mode(struct regulator_dev *rdev,
.desc.ops = &da9062_ldo_ops,
.desc.min_uV = (900) * 1000,
.desc.uV_step = (50) * 1000,
- .desc.n_voltages = ((3600) - (900))/(50) + 1,
+ .desc.n_voltages = ((3600) - (900))/(50) + 1
+ + DA9062AA_VLDO_A_MIN_SEL,
.desc.enable_reg = DA9062AA_LDO4_CONT,
.desc.enable_mask = DA9062AA_LDO4_EN_MASK,
.desc.vsel_reg = DA9062AA_VLDO4_A,
.desc.vsel_mask = DA9062AA_VLDO4_A_MASK,
- .desc.linear_min_sel = 0,
+ .desc.linear_min_sel = DA9062AA_VLDO_A_MIN_SEL,
.sleep = REG_FIELD(DA9062AA_VLDO4_A,
__builtin_ffs((int)DA9062AA_LDO4_SL_A_MASK) - 1,
sizeof(unsigned int) * 8 -
diff --git a/include/linux/mfd/da9062/registers.h b/include/linux/mfd/da9062/registers.h
index fe04b70..090213a 100644
--- a/include/linux/mfd/da9062/registers.h
+++ b/include/linux/mfd/da9062/registers.h
@@ -797,6 +797,9 @@
#define DA9062AA_BUCK3_SL_A_SHIFT 7
#define DA9062AA_BUCK3_SL_A_MASK BIT(7)
+/* DA9062AA_VLDO[1-4]_A common */
+#define DA9062AA_VLDO_A_MIN_SEL 2
+
/* DA9062AA_VLDO1_A = 0x0A9 */
#define DA9062AA_VLDO1_A_SHIFT 0
#define DA9062AA_VLDO1_A_MASK 0x3f
--
1.9.3
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [PATCH V3] regulator: da9061/62: Adjust LDO voltage selection minimum value
2019-06-19 16:35 [PATCH V3] regulator: da9061/62: Adjust LDO voltage selection minimum value Steve Twiss
@ 2019-06-19 16:55 ` Mark Brown
0 siblings, 0 replies; 2+ messages in thread
From: Mark Brown @ 2019-06-19 16:55 UTC (permalink / raw)
To: Steve Twiss
Cc: Liam Girdwood, Lee Jones, Felix Riemann, Support Opensource, LKML
[-- Attachment #1: Type: text/plain, Size: 491 bytes --]
On Wed, Jun 19, 2019 at 05:35:00PM +0100, Steve Twiss wrote:
> Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
> Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
> Signed-off-by: Felix Riemann <felix.riemann@sma.de>
> ---
>
> Hi Mark,
>
> I've added my signed-off tag to the commit patch of V3.
The signoffs really should come in order - the last signoff should be
from the person sending the patch.
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2019-06-19 16:55 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-06-19 16:35 [PATCH V3] regulator: da9061/62: Adjust LDO voltage selection minimum value Steve Twiss
2019-06-19 16:55 ` Mark Brown
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®