[PATCH v1 3/3] tty: serial: lpuart: Add RS485 support for 32-bit uart flavour

[Philippe Schenker <philippe.schenker@toradex.com>]

This commits adds RS485 support for LPUART hardware that uses 32-bit
registers. These are typically found in i.MX8 processors.

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>

---

 drivers/tty/serial/fsl_lpuart.c | 65 ++++++++++++++++++++++++++++++++-
 1 file changed, 63 insertions(+), 2 deletions(-)

diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index 346b4a070ce9..22df5f8f48b6 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -1280,6 +1280,57 @@ static int lpuart_config_rs485(struct uart_port *port,
 	return 0;
 }
 
+static int lpuart32_config_rs485(struct uart_port *port,
+			struct serial_rs485 *rs485)
+{
+	struct lpuart_port *sport = container_of(port,
+			struct lpuart_port, port);
+
+	unsigned long modem = lpuart32_read(&sport->port, UARTMODIR)
+				& ~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE);
+	lpuart32_write(&sport->port, modem, UARTMODIR);
+
+	/* clear unsupported configurations */
+	rs485->delay_rts_before_send = 0;
+	rs485->delay_rts_after_send = 0;
+	rs485->flags &= ~SER_RS485_RX_DURING_TX;
+
+	if (rs485->flags & SER_RS485_ENABLED) {
+		/* Enable auto RS-485 RTS mode */
+		modem |= UARTMODEM_TXRTSE;
+
+		/*
+		 * RTS needs to be logic HIGH either during transer _or_ after
+		 * transfer, other variants are not supported by the hardware.
+		 */
+
+		if (!(rs485->flags & (SER_RS485_RTS_ON_SEND |
+				SER_RS485_RTS_AFTER_SEND)))
+			rs485->flags |= SER_RS485_RTS_ON_SEND;
+
+		if (rs485->flags & SER_RS485_RTS_ON_SEND &&
+				rs485->flags & SER_RS485_RTS_AFTER_SEND)
+			rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
+
+		/*
+		 * The hardware defaults to RTS logic HIGH while transfer.
+		 * Switch polarity in case RTS shall be logic HIGH
+		 * after transfer.
+		 * Note: UART is assumed to be active high.
+		 */
+		if (rs485->flags & SER_RS485_RTS_ON_SEND)
+			modem &= ~UARTMODEM_TXRTSPOL;
+		else if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
+			modem |= UARTMODEM_TXRTSPOL;
+	}
+
+	/* Store the new configuration */
+	sport->port.rs485 = *rs485;
+
+	lpuart32_write(&sport->port, modem, UARTMODIR);
+	return 0;
+}
+
 static unsigned int lpuart_get_mctrl(struct uart_port *port)
 {
 	unsigned int temp = 0;
@@ -1878,6 +1929,13 @@ lpuart32_set_termios(struct uart_port *port, struct ktermios *termios,
 		ctrl |= UARTCTRL_M;
 	}
 
+	/*
+	 * When auto RS-485 RTS mode is enabled,
+	 * hardware flow control need to be disabled.
+	 */
+	if (sport->port.rs485.flags & SER_RS485_ENABLED)
+		termios->c_cflag &= ~CRTSCTS;
+
 	if (termios->c_cflag & CRTSCTS) {
 		modem |= (UARTMODIR_RXRTSE | UARTMODIR_TXCTSE);
 	} else {
@@ -2405,7 +2463,10 @@ static int lpuart_probe(struct platform_device *pdev)
 		sport->port.ops = &lpuart_pops;
 	sport->port.flags = UPF_BOOT_AUTOCONF;
 
-	sport->port.rs485_config = lpuart_config_rs485;
+	if (lpuart_is_32(sport))
+		sport->port.rs485_config = lpuart32_config_rs485;
+	else
+		sport->port.rs485_config = lpuart_config_rs485;
 
 	sport->ipg_clk = devm_clk_get(&pdev->dev, "ipg");
 	if (IS_ERR(sport->ipg_clk)) {
@@ -2459,7 +2520,7 @@ static int lpuart_probe(struct platform_device *pdev)
 	    sport->port.rs485.delay_rts_after_send)
 		dev_err(&pdev->dev, "driver doesn't support RTS delays\n");
 
-	lpuart_config_rs485(&sport->port, &sport->port.rs485);
+	sport->port.rs485_config(&sport->port, &sport->port.rs485);
 
 	sport->dma_tx_chan = dma_request_slave_channel(sport->port.dev, "tx");
 	if (!sport->dma_tx_chan)
-- 
2.23.0