From: Michal Kubecek <mkubecek@suse.cz>
To: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>,
"David S. Miller" <davem@davemloft.net>,
Florian Fainelli <f.fainelli@gmail.com>,
Heiner Kallweit <hkallweit1@gmail.com>,
Jakub Kicinski <kuba@kernel.org>,
Jonathan Corbet <corbet@lwn.net>,
"John W. Linville" <linville@tuxdriver.com>,
David Jander <david@protonic.nl>,
kernel@pengutronix.de, linux-kernel@vger.kernel.org,
netdev@vger.kernel.org, Russell King <linux@armlinux.org.uk>,
mkl@pengutronix.de, Marek Vasut <marex@denx.de>,
Christian Herber <christian.herber@nxp.com>,
Amit Cohen <amitc@mellanox.com>,
Petr Machata <petrm@mellanox.com>
Subject: Re: [PATCH v2 2/3] netlink: add master/slave configuration support
Date: Sun, 7 Jun 2020 22:39:40 +0200 [thread overview]
Message-ID: <20200607203940.7ayqe4otoop7mpuw@lion.mk-sys.cz> (raw)
In-Reply-To: <20200528115414.11516-3-o.rempel@pengutronix.de>
[-- Attachment #1: Type: text/plain, Size: 2819 bytes --]
On Thu, May 28, 2020 at 01:54:13PM +0200, Oleksij Rempel wrote:
> This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
> auto-negotiation support, we needed to be able to configure the
> MASTER-SLAVE role of the port manually or from an application in user
> space.
>
> The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
> force MASTER or SLAVE role. See IEEE 802.3-2018:
> 22.2.4.3.7 MASTER-SLAVE control register (Register 9)
> 22.2.4.3.8 MASTER-SLAVE status register (Register 10)
> 40.5.2 MASTER-SLAVE configuration resolution
> 45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
> 45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
>
> The MASTER-SLAVE role affects the clock configuration:
>
> -------------------------------------------------------------------------------
> When the PHY is configured as MASTER, the PMA Transmit function shall
> source TX_TCLK from a local clock source. When configured as SLAVE, the
> PMA Transmit function shall source TX_TCLK from the clock recovered from
> data stream provided by MASTER.
>
> iMX6Q KSZ9031 XXX
> ------\ /-----------\ /------------\
> | | | | |
> MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
> |<--- 125 MHz ---+-<------/ | | \ |
> ------/ \-----------/ \------------/
> ^
> \-TX_TCLK
>
> -------------------------------------------------------------------------------
>
> Since some clock or link related issues are only reproducible in a
> specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
> to provide generic (not 100BASE-T1 specific) interface to the user space
> for configuration flexibility and trouble shooting.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
The patch looks good from technical point of view but I don't like the
inconsistency of user interface:
1. Similar to what we discussed earlier on kernel side, you use "Port
mode" in "ethtool <dev>" output but the corresponding command line
argument for "ethtool -s <dev> ..." is "master-slave". Even if it's
documented, it's rather confusing for users.
2. The values for "master-slave" parameter are "master-preferred" and
"master-force" (and the same for "slave"). Please use the same form for
both, i.e. either "prefer / force" or "preferred / forced". Also, it
would be friendlier to users to make the values consistent with
"ethtool <dev>" output, e.g. if it says "preferred Master", setting
should use something as close as possible, i.e. "preferred-master".
Michal
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
next prev parent reply other threads:[~2020-06-07 20:39 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-28 11:54 [PATCH v2 0/3] Add support for SQI and master-slave Oleksij Rempel
2020-05-28 11:54 ` [PATCH v2 1/3] update UAPI header copies Oleksij Rempel
2020-05-28 11:54 ` [PATCH v2 2/3] netlink: add master/slave configuration support Oleksij Rempel
2020-06-07 20:39 ` Michal Kubecek [this message]
2020-05-28 11:54 ` [PATCH v2 3/3] netlink: add LINKSTATE SQI support Oleksij Rempel
2020-06-07 20:24 ` Michal Kubecek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200607203940.7ayqe4otoop7mpuw@lion.mk-sys.cz \
--to=mkubecek@suse.cz \
--cc=amitc@mellanox.com \
--cc=andrew@lunn.ch \
--cc=christian.herber@nxp.com \
--cc=corbet@lwn.net \
--cc=davem@davemloft.net \
--cc=david@protonic.nl \
--cc=f.fainelli@gmail.com \
--cc=hkallweit1@gmail.com \
--cc=kernel@pengutronix.de \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=linville@tuxdriver.com \
--cc=marex@denx.de \
--cc=mkl@pengutronix.de \
--cc=netdev@vger.kernel.org \
--cc=o.rempel@pengutronix.de \
--cc=petrm@mellanox.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®