mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
* [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs
@ 2020-07-10 14:35 Douglas Anderson
  2020-07-10 14:35 ` [PATCH v5 1/4] dt-bindings: nvmem: qfprom: Convert to yaml Douglas Anderson
                   ` (5 more replies)
  0 siblings, 6 replies; 7+ messages in thread
From: Douglas Anderson @ 2020-07-10 14:35 UTC (permalink / raw)
  To: Srinivas Kandagatla, Rob Herring, Bjorn Andersson, Andy Gross
  Cc: sparate, saiprakash.ranjan, mturney, linux-arm-msm, Jeffrey Hugo,
	dhavalp, rnayak, mkurumel, Ravi Kumar Bokka, Douglas Anderson,
	devicetree, linux-kernel

This series enables blowing of fuses on Qualcomm SoCs by extending the
existing qfprom driver with write support.

A few notes:
- Though I don't have any firsthand knowledge of it, it's my
  understanding that these changes could be used on any Qualcomm SoC.
  However, it's likely not very useful on most boards because the
  bootloader protects against this.  Thus the write support here is
  likely only useful with a cooperating bootloader.
- Blowing fuses is truly a one-way process.  If you mess around with
  this and do something wrong you could irreparably brick your chip.
  You have been warned.

Versions 1 and 2 of this series were posted by Ravi Kumar Bokka.  I
posted version 3 containing my changes / fixups with his consent.  I
have left authorship as Ravi but added my own Signed-off-by.

Version 4 is a minor spin over version 3.

Version 5 is an even more minor spin and just bumps up some timings to
fix a failure reported by Ravi on one device.  I've collected Rob
Herring's reviews and (as far as I know) this is ready to land.

Changes in v5:
- QFPROM_FUSE_BLOW_POLL_US 10 => 100
- QFPROM_FUSE_BLOW_TIMEOUT_US 100 => 1000

Changes in v4:
- Maintainer now listed as Srinivas.
- Example under "soc" to get #address-cells and #size-cells.
- Clock name is "core", not "sec".
- Example under "soc" to get #address-cells and #size-cells.
- Only get clock/regulator if all address ranges are provided.
- Don't use optional version of clk_get now.
- Clock name is "core", not "sec".
- Cleaned up error message if couldn't get clock.
- Fixed up minor version mask.
- Use GENMASK to generate masks.
- Clock name is "core", not "sec".

Changes in v3:
- Split conversion to yaml into separate patch new in v3.
- Use 'const' for compatible instead of a 1-entry enum.
- Changed filename to match compatible string.
- Add #address-cells and #size-cells to list of properties.
- Fixed up example.
- Add an extra reg range (at 0x6000 offset for SoCs checked)
- Define two options for reg: 1 item or 4 items.
- No reg-names.
- Add "clocks" and "clock-names" to list of properties.
- Clock is now "sec", not "secclk".
- Add "vcc-supply" to list of properties.
- Fixed up example.
- Don't provide "reset" value for things; just save/restore.
- Use the major/minor version read from 0x6000.
- Reading should still read "corrected", not "raw".
- Added a sysfs knob to allow you to read "raw" instead of "corrected"
- Simplified the SoC data structure.
- No need for quite so many levels of abstraction for clocks/regulator.
- Don't set regulator voltage.  Rely on device tree to make sure it's right.
- Properly undo things in the case of failure.
- Don't just keep enabling the regulator over and over again.
- Enable / disable the clock each time
- Polling every 100 us but timing out in 10 us didn't make sense; swap.
- No reason for 100 us to be SoC specific.
- No need for reg-names.
- We shouldn't be creating two separate nvmem devices.
- Name is now 'efuse' to match what schema checker wants.
- Reorganized ranges to match driver/bindings changes.
- Added 4th range as per driver/binding changes.
- No more reg-names as per driver/binding changes.
- Clock name is now just "sec" as per driver/binding changes.

Ravi Kumar Bokka (4):
  dt-bindings: nvmem: qfprom: Convert to yaml
  dt-bindings: nvmem: Add properties needed for blowing fuses
  nvmem: qfprom: Add fuse blowing support
  arm64: dts: qcom: sc7180: Add properties to qfprom for fuse blowing

 .../bindings/nvmem/qcom,qfprom.yaml           |  96 ++++++
 .../devicetree/bindings/nvmem/qfprom.txt      |  35 --
 arch/arm64/boot/dts/qcom/sc7180-idp.dts       |   4 +
 arch/arm64/boot/dts/qcom/sc7180.dtsi          |  10 +-
 drivers/nvmem/qfprom.c                        | 314 +++++++++++++++++-
 5 files changed, 411 insertions(+), 48 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
 delete mode 100644 Documentation/devicetree/bindings/nvmem/qfprom.txt

-- 
2.27.0.383.g050319c2ae-goog


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v5 1/4] dt-bindings: nvmem: qfprom: Convert to yaml
  2020-07-10 14:35 [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Douglas Anderson
@ 2020-07-10 14:35 ` Douglas Anderson
  2020-07-10 14:35 ` [PATCH v5 2/4] dt-bindings: nvmem: Add properties needed for blowing fuses Douglas Anderson
                   ` (4 subsequent siblings)
  5 siblings, 0 replies; 7+ messages in thread
From: Douglas Anderson @ 2020-07-10 14:35 UTC (permalink / raw)
  To: Srinivas Kandagatla, Rob Herring, Bjorn Andersson, Andy Gross
  Cc: sparate, saiprakash.ranjan, mturney, linux-arm-msm, Jeffrey Hugo,
	dhavalp, rnayak, mkurumel, Ravi Kumar Bokka, Douglas Anderson,
	Rob Herring, devicetree, linux-kernel

From: Ravi Kumar Bokka <rbokka@codeaurora.org>

This switches the bindings over from txt to yaml.

Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---

Changes in v5: None
Changes in v4:
- Maintainer now listed as Srinivas.
- Example under "soc" to get #address-cells and #size-cells.

Changes in v3:
- Split conversion to yaml into separate patch new in v3.
- Use 'const' for compatible instead of a 1-entry enum.
- Changed filename to match compatible string.
- Add #address-cells and #size-cells to list of properties.
- Fixed up example.

 .../bindings/nvmem/qcom,qfprom.yaml           | 50 +++++++++++++++++++
 .../devicetree/bindings/nvmem/qfprom.txt      | 35 -------------
 2 files changed, 50 insertions(+), 35 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
 delete mode 100644 Documentation/devicetree/bindings/nvmem/qfprom.txt

diff --git a/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml b/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
new file mode 100644
index 000000000000..39f97c1c83a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/nvmem/qcom,qfprom.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies Inc, QFPROM Efuse bindings
+
+maintainers:
+  - Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
+
+allOf:
+  - $ref: "nvmem.yaml#"
+
+properties:
+  compatible:
+    const: qcom,qfprom
+
+  reg:
+    items:
+      - description: The corrected region.
+
+  # Needed if any child nodes are present.
+  "#address-cells":
+    const: 1
+  "#size-cells":
+    const: 1
+
+required:
+   - compatible
+   - reg
+
+examples:
+  - |
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      efuse@784000 {
+        compatible = "qcom,qfprom";
+        reg = <0 0x00784000 0 0x8ff>;
+        #address-cells = <1>;
+        #size-cells = <1>;
+
+        hstx-trim-primary@1eb {
+          reg = <0x1eb 0x1>;
+          bits = <1 4>;
+        };
+      };
+    };
diff --git a/Documentation/devicetree/bindings/nvmem/qfprom.txt b/Documentation/devicetree/bindings/nvmem/qfprom.txt
deleted file mode 100644
index 26fe878d5c86..000000000000
--- a/Documentation/devicetree/bindings/nvmem/qfprom.txt
+++ /dev/null
@@ -1,35 +0,0 @@
-= Qualcomm QFPROM device tree bindings =
-
-This binding is intended to represent QFPROM which is found in most QCOM SOCs.
-
-Required properties:
-- compatible: should be "qcom,qfprom"
-- reg: Should contain registers location and length
-
-= Data cells =
-Are child nodes of qfprom, bindings of which as described in
-bindings/nvmem/nvmem.txt
-
-Example:
-
-	qfprom: qfprom@700000 {
-		compatible 	= "qcom,qfprom";
-		reg		= <0x00700000 0x8000>;
-		...
-		/* Data cells */
-		tsens_calibration: calib@404 {
-			reg = <0x4404 0x10>;
-		};
-	};
-
-
-= Data consumers =
-Are device nodes which consume nvmem data cells.
-
-For example:
-
-	tsens {
-		...
-		nvmem-cells = <&tsens_calibration>;
-		nvmem-cell-names = "calibration";
-	};
-- 
2.27.0.383.g050319c2ae-goog


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v5 2/4] dt-bindings: nvmem: Add properties needed for blowing fuses
  2020-07-10 14:35 [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Douglas Anderson
  2020-07-10 14:35 ` [PATCH v5 1/4] dt-bindings: nvmem: qfprom: Convert to yaml Douglas Anderson
@ 2020-07-10 14:35 ` Douglas Anderson
  2020-07-10 14:35 ` [PATCH v5 3/4] nvmem: qfprom: Add fuse blowing support Douglas Anderson
                   ` (3 subsequent siblings)
  5 siblings, 0 replies; 7+ messages in thread
From: Douglas Anderson @ 2020-07-10 14:35 UTC (permalink / raw)
  To: Srinivas Kandagatla, Rob Herring, Bjorn Andersson, Andy Gross
  Cc: sparate, saiprakash.ranjan, mturney, linux-arm-msm, Jeffrey Hugo,
	dhavalp, rnayak, mkurumel, Ravi Kumar Bokka, Douglas Anderson,
	Rob Herring, devicetree, linux-kernel

From: Ravi Kumar Bokka <rbokka@codeaurora.org>

On some systems it's possible to actually blow the fuses in the qfprom
from the kernel.  Add properties to support that.

NOTE: Whether this is possible depends on the BIOS settings and
whether the kernel has permissions here, so not all boards will be
able to blow fuses in the kernel.

Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---

Changes in v5: None
Changes in v4:
- Clock name is "core", not "sec".
- Example under "soc" to get #address-cells and #size-cells.

Changes in v3:
- Add an extra reg range (at 0x6000 offset for SoCs checked)
- Define two options for reg: 1 item or 4 items.
- No reg-names.
- Add "clocks" and "clock-names" to list of properties.
- Clock is now "sec", not "secclk".
- Add "vcc-supply" to list of properties.
- Fixed up example.

 .../bindings/nvmem/qcom,qfprom.yaml           | 50 ++++++++++++++++++-
 1 file changed, 48 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml b/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
index 39f97c1c83a4..d10a0cf91ba7 100644
--- a/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
+++ b/Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
@@ -17,8 +17,27 @@ properties:
     const: qcom,qfprom
 
   reg:
-    items:
-      - description: The corrected region.
+    # If the QFPROM is read-only OS image then only the corrected region
+    # needs to be provided.  If the QFPROM is writable then all 4 regions
+    # must be provided.
+    oneOf:
+      - items:
+          - description: The corrected region.
+      - items:
+          - description: The corrected region.
+          - description: The raw region.
+          - description: The config region.
+          - description: The security control region.
+
+  # Clock must be provided if QFPROM is writable from the OS image.
+  clocks:
+    maxItems: 1
+  clock-names:
+    const: core
+
+  # Supply reference must be provided if QFPROM is writable from the OS image.
+  vcc-supply:
+    description: Our power supply.
 
   # Needed if any child nodes are present.
   "#address-cells":
@@ -31,6 +50,33 @@ required:
    - reg
 
 examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-sc7180.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      efuse@784000 {
+        compatible = "qcom,qfprom";
+        reg = <0 0x00784000 0 0x8ff>,
+              <0 0x00780000 0 0x7a0>,
+              <0 0x00782000 0 0x100>,
+              <0 0x00786000 0 0x1fff>;
+        clocks = <&gcc GCC_SEC_CTRL_CLK_SRC>;
+        clock-names = "core";
+        #address-cells = <1>;
+        #size-cells = <1>;
+
+        vcc-supply = <&vreg_l11a_1p8>;
+
+        hstx-trim-primary@25b {
+          reg = <0x25b 0x1>;
+          bits = <1 3>;
+        };
+      };
+    };
+
   - |
     soc {
       #address-cells = <2>;
-- 
2.27.0.383.g050319c2ae-goog


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v5 3/4] nvmem: qfprom: Add fuse blowing support
  2020-07-10 14:35 [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Douglas Anderson
  2020-07-10 14:35 ` [PATCH v5 1/4] dt-bindings: nvmem: qfprom: Convert to yaml Douglas Anderson
  2020-07-10 14:35 ` [PATCH v5 2/4] dt-bindings: nvmem: Add properties needed for blowing fuses Douglas Anderson
@ 2020-07-10 14:35 ` Douglas Anderson
  2020-07-10 14:35 ` [PATCH v5 4/4] arm64: dts: qcom: sc7180: Add properties to qfprom for fuse blowing Douglas Anderson
                   ` (2 subsequent siblings)
  5 siblings, 0 replies; 7+ messages in thread
From: Douglas Anderson @ 2020-07-10 14:35 UTC (permalink / raw)
  To: Srinivas Kandagatla, Rob Herring, Bjorn Andersson, Andy Gross
  Cc: sparate, saiprakash.ranjan, mturney, linux-arm-msm, Jeffrey Hugo,
	dhavalp, rnayak, mkurumel, Ravi Kumar Bokka, Douglas Anderson,
	linux-kernel

From: Ravi Kumar Bokka <rbokka@codeaurora.org>

This patch adds support for blowing fuses to the qfprom driver if the
required properties are defined in the device tree.

Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
---

Changes in v5:
- QFPROM_FUSE_BLOW_POLL_US 10 => 100
- QFPROM_FUSE_BLOW_TIMEOUT_US 100 => 1000

Changes in v4:
- Only get clock/regulator if all address ranges are provided.
- Don't use optional version of clk_get now.
- Clock name is "core", not "sec".
- Cleaned up error message if couldn't get clock.
- Fixed up minor version mask.
- Use GENMASK to generate masks.

Changes in v3:
- Don't provide "reset" value for things; just save/restore.
- Use the major/minor version read from 0x6000.
- Reading should still read "corrected", not "raw".
- Added a sysfs knob to allow you to read "raw" instead of "corrected"
- Simplified the SoC data structure.
- No need for quite so many levels of abstraction for clocks/regulator.
- Don't set regulator voltage.  Rely on device tree to make sure it's right.
- Properly undo things in the case of failure.
- Don't just keep enabling the regulator over and over again.
- Enable / disable the clock each time
- Polling every 100 us but timing out in 10 us didn't make sense; swap.
- No reason for 100 us to be SoC specific.
- No need for reg-names.
- We shouldn't be creating two separate nvmem devices.

 drivers/nvmem/qfprom.c | 314 +++++++++++++++++++++++++++++++++++++++--
 1 file changed, 303 insertions(+), 11 deletions(-)

diff --git a/drivers/nvmem/qfprom.c b/drivers/nvmem/qfprom.c
index 8a91717600be..546c34666747 100644
--- a/drivers/nvmem/qfprom.c
+++ b/drivers/nvmem/qfprom.c
@@ -3,57 +3,349 @@
  * Copyright (C) 2015 Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
  */
 
+#include <linux/clk.h>
 #include <linux/device.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/mod_devicetable.h>
-#include <linux/io.h>
 #include <linux/nvmem-provider.h>
 #include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+
+/* Blow timer clock frequency in Mhz */
+#define QFPROM_BLOW_TIMER_OFFSET 0x03c
+
+/* Amount of time required to hold charge to blow fuse in micro-seconds */
+#define QFPROM_FUSE_BLOW_POLL_US	100
+#define QFPROM_FUSE_BLOW_TIMEOUT_US	1000
+
+#define QFPROM_BLOW_STATUS_OFFSET	0x048
+#define QFPROM_BLOW_STATUS_BUSY		0x1
+#define QFPROM_BLOW_STATUS_READY	0x0
+
+#define QFPROM_ACCEL_OFFSET		0x044
+
+#define QFPROM_VERSION_OFFSET		0x0
+#define QFPROM_MAJOR_VERSION_SHIFT	28
+#define QFPROM_MAJOR_VERSION_MASK	GENMASK(31, QFPROM_MAJOR_VERSION_SHIFT)
+#define QFPROM_MINOR_VERSION_SHIFT	16
+#define QFPROM_MINOR_VERSION_MASK	GENMASK(27, QFPROM_MINOR_VERSION_SHIFT)
+
+static bool read_raw_data;
+module_param(read_raw_data, bool, 0644);
+MODULE_PARM_DESC(read_raw_data, "Read raw instead of corrected data");
 
+/**
+ * struct qfprom_soc_data - config that varies from SoC to SoC.
+ *
+ * @accel_value:             Should contain qfprom accel value.
+ * @qfprom_blow_timer_value: The timer value of qfprom when doing efuse blow.
+ * @qfprom_blow_set_freq:    The frequency required to set when we start the
+ *                           fuse blowing.
+ */
+struct qfprom_soc_data {
+	u32 accel_value;
+	u32 qfprom_blow_timer_value;
+	u32 qfprom_blow_set_freq;
+};
+
+/**
+ * struct qfprom_priv - structure holding qfprom attributes
+ *
+ * @qfpraw:       iomapped memory space for qfprom-efuse raw address space.
+ * @qfpconf:      iomapped memory space for qfprom-efuse configuration address
+ *                space.
+ * @qfpcorrected: iomapped memory space for qfprom corrected address space.
+ * @qfpsecurity:  iomapped memory space for qfprom security control space.
+ * @dev:          qfprom device structure.
+ * @secclk:       Clock supply.
+ * @vcc:          Regulator supply.
+ * @soc_data:     Data that for things that varies from SoC to SoC.
+ */
 struct qfprom_priv {
-	void __iomem *base;
+	void __iomem *qfpraw;
+	void __iomem *qfpconf;
+	void __iomem *qfpcorrected;
+	void __iomem *qfpsecurity;
+	struct device *dev;
+	struct clk *secclk;
+	struct regulator *vcc;
+	const struct qfprom_soc_data *soc_data;
+};
+
+/**
+ * struct qfprom_touched_values - saved values to restore after blowing
+ *
+ * @clk_rate: The rate the clock was at before blowing.
+ * @accel_val: The value of the accel reg before blowing.
+ * @timer_val: The value of the timer before blowing.
+ */
+struct qfprom_touched_values {
+	unsigned long clk_rate;
+	u32 accel_val;
+	u32 timer_val;
 };
 
+/**
+ * qfprom_disable_fuse_blowing() - Undo enabling of fuse blowing.
+ * @priv: Our driver data.
+ * @old:  The data that was stashed from before fuse blowing.
+ *
+ * Resets the value of the blow timer, accel register and the clock
+ * and voltage settings.
+ *
+ * Prints messages if there are errors but doesn't return an error code
+ * since there's not much we can do upon failure.
+ */
+static void qfprom_disable_fuse_blowing(const struct qfprom_priv *priv,
+					const struct qfprom_touched_values *old)
+{
+	int ret;
+
+	ret = regulator_disable(priv->vcc);
+	if (ret)
+		dev_warn(priv->dev, "Failed to disable regulator (ignoring)\n");
+
+	ret = clk_set_rate(priv->secclk, old->clk_rate);
+	if (ret)
+		dev_warn(priv->dev,
+			 "Failed to set clock rate for disable (ignoring)\n");
+
+	clk_disable_unprepare(priv->secclk);
+
+	writel(old->timer_val, priv->qfpconf + QFPROM_BLOW_TIMER_OFFSET);
+	writel(old->accel_val, priv->qfpconf + QFPROM_ACCEL_OFFSET);
+}
+
+/**
+ * qfprom_enable_fuse_blowing() - Enable fuse blowing.
+ * @priv: Our driver data.
+ * @old:  We'll stash stuff here to use when disabling.
+ *
+ * Sets the value of the blow timer, accel register and the clock
+ * and voltage settings.
+ *
+ * Prints messages if there are errors so caller doesn't need to.
+ *
+ * Return: 0 or -err.
+ */
+static int qfprom_enable_fuse_blowing(const struct qfprom_priv *priv,
+				      struct qfprom_touched_values *old)
+{
+	int ret;
+
+	ret = clk_prepare_enable(priv->secclk);
+	if (ret) {
+		dev_err(priv->dev, "Failed to enable clock\n");
+		return ret;
+	}
+
+	old->clk_rate = clk_get_rate(priv->secclk);
+	ret = clk_set_rate(priv->secclk, priv->soc_data->qfprom_blow_set_freq);
+	if (ret) {
+		dev_err(priv->dev, "Failed to set clock rate for enable\n");
+		goto err_clk_prepared;
+	}
+
+	ret = regulator_enable(priv->vcc);
+	if (ret) {
+		dev_err(priv->dev, "Failed to enable regulator\n");
+		goto err_clk_rate_set;
+	}
+
+	old->timer_val = readl(priv->qfpconf + QFPROM_BLOW_TIMER_OFFSET);
+	old->accel_val = readl(priv->qfpconf + QFPROM_ACCEL_OFFSET);
+	writel(priv->soc_data->qfprom_blow_timer_value,
+	       priv->qfpconf + QFPROM_BLOW_TIMER_OFFSET);
+	writel(priv->soc_data->accel_value,
+	       priv->qfpconf + QFPROM_ACCEL_OFFSET);
+
+	return 0;
+
+err_clk_rate_set:
+	clk_set_rate(priv->secclk, old->clk_rate);
+err_clk_prepared:
+	clk_disable_unprepare(priv->secclk);
+	return ret;
+}
+
+/**
+ * qfprom_efuse_reg_write() - Write to fuses.
+ * @context: Our driver data.
+ * @reg:     The offset to write at.
+ * @_val:    Pointer to data to write.
+ * @bytes:   The number of bytes to write.
+ *
+ * Writes to fuses.  WARNING: THIS IS PERMANENT.
+ *
+ * Return: 0 or -err.
+ */
+static int qfprom_reg_write(void *context, unsigned int reg, void *_val,
+			    size_t bytes)
+{
+	struct qfprom_priv *priv = context;
+	struct qfprom_touched_values old;
+	int words = bytes / 4;
+	u32 *value = _val;
+	u32 blow_status;
+	int ret;
+	int i;
+
+	dev_dbg(priv->dev,
+		"Writing to raw qfprom region : %#010x of size: %zu\n",
+		reg, bytes);
+
+	/*
+	 * The hardware only allows us to write word at a time, but we can
+	 * read byte at a time.  Until the nvmem framework allows a separate
+	 * word_size and stride for reading vs. writing, we'll enforce here.
+	 */
+	if (bytes % 4) {
+		dev_err(priv->dev,
+			"%zu is not an integral number of words\n", bytes);
+		return -EINVAL;
+	}
+	if (reg % 4) {
+		dev_err(priv->dev,
+			"Invalid offset: %#x.  Must be word aligned\n", reg);
+		return -EINVAL;
+	}
+
+	ret = qfprom_enable_fuse_blowing(priv, &old);
+	if (ret)
+		return ret;
+
+	ret = readl_relaxed_poll_timeout(
+		priv->qfpconf + QFPROM_BLOW_STATUS_OFFSET,
+		blow_status, blow_status == QFPROM_BLOW_STATUS_READY,
+		QFPROM_FUSE_BLOW_POLL_US, QFPROM_FUSE_BLOW_TIMEOUT_US);
+
+	if (ret) {
+		dev_err(priv->dev,
+			"Timeout waiting for initial ready; aborting.\n");
+		goto exit_enabled_fuse_blowing;
+	}
+
+	for (i = 0; i < words; i++)
+		writel(value[i], priv->qfpraw + reg + (i * 4));
+
+	ret = readl_relaxed_poll_timeout(
+		priv->qfpconf + QFPROM_BLOW_STATUS_OFFSET,
+		blow_status, blow_status == QFPROM_BLOW_STATUS_READY,
+		QFPROM_FUSE_BLOW_POLL_US, QFPROM_FUSE_BLOW_TIMEOUT_US);
+
+	/* Give an error, but not much we can do in this case */
+	if (ret)
+		dev_err(priv->dev, "Timeout waiting for finish.\n");
+
+exit_enabled_fuse_blowing:
+	qfprom_disable_fuse_blowing(priv, &old);
+
+	return ret;
+}
+
 static int qfprom_reg_read(void *context,
 			unsigned int reg, void *_val, size_t bytes)
 {
 	struct qfprom_priv *priv = context;
 	u8 *val = _val;
 	int i = 0, words = bytes;
+	void __iomem *base = priv->qfpcorrected;
+
+	if (read_raw_data && priv->qfpraw)
+		base = priv->qfpraw;
 
 	while (words--)
-		*val++ = readb(priv->base + reg + i++);
+		*val++ = readb(base + reg + i++);
 
 	return 0;
 }
 
-static struct nvmem_config econfig = {
-	.name = "qfprom",
-	.stride = 1,
-	.word_size = 1,
-	.reg_read = qfprom_reg_read,
+static const struct qfprom_soc_data qfprom_7_8_data = {
+	.accel_value = 0xD10,
+	.qfprom_blow_timer_value = 25,
+	.qfprom_blow_set_freq = 4800000,
 };
 
 static int qfprom_probe(struct platform_device *pdev)
 {
+	struct nvmem_config econfig = {
+		.name = "qfprom",
+		.stride = 1,
+		.word_size = 1,
+		.reg_read = qfprom_reg_read,
+	};
 	struct device *dev = &pdev->dev;
 	struct resource *res;
 	struct nvmem_device *nvmem;
 	struct qfprom_priv *priv;
+	int ret;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
 
+	/* The corrected section is always provided */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	priv->base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(priv->base))
-		return PTR_ERR(priv->base);
+	priv->qfpcorrected = devm_ioremap_resource(dev, res);
+	if (IS_ERR(priv->qfpcorrected))
+		return PTR_ERR(priv->qfpcorrected);
 
 	econfig.size = resource_size(res);
 	econfig.dev = dev;
 	econfig.priv = priv;
 
+	priv->dev = dev;
+
+	/*
+	 * If more than one region is provided then the OS has the ability
+	 * to write.
+	 */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	if (res) {
+		u32 version;
+		int major_version, minor_version;
+
+		priv->qfpraw = devm_ioremap_resource(dev, res);
+		if (IS_ERR(priv->qfpraw))
+			return PTR_ERR(priv->qfpraw);
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+		priv->qfpconf = devm_ioremap_resource(dev, res);
+		if (IS_ERR(priv->qfpconf))
+			return PTR_ERR(priv->qfpconf);
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 3);
+		priv->qfpsecurity = devm_ioremap_resource(dev, res);
+		if (IS_ERR(priv->qfpsecurity))
+			return PTR_ERR(priv->qfpsecurity);
+
+		version = readl(priv->qfpsecurity + QFPROM_VERSION_OFFSET);
+		major_version = (version & QFPROM_MAJOR_VERSION_MASK) >>
+				QFPROM_MAJOR_VERSION_SHIFT;
+		minor_version = (version & QFPROM_MINOR_VERSION_MASK) >>
+				QFPROM_MINOR_VERSION_SHIFT;
+
+		if (major_version == 7 && minor_version == 8)
+			priv->soc_data = &qfprom_7_8_data;
+
+		priv->vcc = devm_regulator_get(&pdev->dev, "vcc");
+		if (IS_ERR(priv->vcc))
+			return PTR_ERR(priv->vcc);
+
+		priv->secclk = devm_clk_get(dev, "core");
+		if (IS_ERR(priv->secclk)) {
+			ret = PTR_ERR(priv->secclk);
+			if (ret != -EPROBE_DEFER)
+				dev_err(dev, "Error getting clock: %d\n", ret);
+			return ret;
+		}
+
+		/* Only enable writing if we have SoC data. */
+		if (priv->soc_data)
+			econfig.reg_write = qfprom_reg_write;
+	}
+
 	nvmem = devm_nvmem_register(dev, &econfig);
 
 	return PTR_ERR_OR_ZERO(nvmem);
-- 
2.27.0.383.g050319c2ae-goog


^ permalink raw reply	[flat|nested] 7+ messages in thread

* [PATCH v5 4/4] arm64: dts: qcom: sc7180: Add properties to qfprom for fuse blowing
  2020-07-10 14:35 [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Douglas Anderson
                   ` (2 preceding siblings ...)
  2020-07-10 14:35 ` [PATCH v5 3/4] nvmem: qfprom: Add fuse blowing support Douglas Anderson
@ 2020-07-10 14:35 ` Douglas Anderson
  2020-07-14 22:49 ` [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Doug Anderson
  2020-07-20  9:05 ` Srinivas Kandagatla
  5 siblings, 0 replies; 7+ messages in thread
From: Douglas Anderson @ 2020-07-10 14:35 UTC (permalink / raw)
  To: Srinivas Kandagatla, Rob Herring, Bjorn Andersson, Andy Gross
  Cc: sparate, saiprakash.ranjan, mturney, linux-arm-msm, Jeffrey Hugo,
	dhavalp, rnayak, mkurumel, Ravi Kumar Bokka, Douglas Anderson,
	devicetree, linux-kernel

From: Ravi Kumar Bokka <rbokka@codeaurora.org>

This patch adds properties to the qfprom node to enable fuse blowing.

Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
---
Presumably this patch to the device tree file should go through the
Qualcomm tree.  Now that bindings have been reviewed by Rob it could
probably land any time.

Changes in v5: None
Changes in v4:
- Clock name is "core", not "sec".

Changes in v3:
- Name is now 'efuse' to match what schema checker wants.
- Reorganized ranges to match driver/bindings changes.
- Added 4th range as per driver/binding changes.
- No more reg-names as per driver/binding changes.
- Clock name is now just "sec" as per driver/binding changes.

 arch/arm64/boot/dts/qcom/sc7180-idp.dts |  4 ++++
 arch/arm64/boot/dts/qcom/sc7180.dtsi    | 10 ++++++++--
 2 files changed, 12 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 4e9149d82d09..2a9224e2083f 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -287,6 +287,10 @@ vreg_bob: bob {
 	};
 };
 
+&qfprom {
+	vcc-supply = <&vreg_l11a_1p8>;
+};
+
 &qspi {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 31b9217bb5bf..fbf9554f1e3a 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -498,9 +498,15 @@ gcc: clock-controller@100000 {
 			#power-domain-cells = <1>;
 		};
 
-		qfprom@784000 {
+		qfprom: efuse@784000 {
 			compatible = "qcom,qfprom";
-			reg = <0 0x00784000 0 0x8ff>;
+			reg = <0 0x00784000 0 0x8ff>,
+			      <0 0x00780000 0 0x7a0>,
+			      <0 0x00782000 0 0x100>,
+			      <0 0x00786000 0 0x1fff>;
+
+			clocks = <&gcc GCC_SEC_CTRL_CLK_SRC>;
+			clock-names = "core";
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-- 
2.27.0.383.g050319c2ae-goog


^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs
  2020-07-10 14:35 [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Douglas Anderson
                   ` (3 preceding siblings ...)
  2020-07-10 14:35 ` [PATCH v5 4/4] arm64: dts: qcom: sc7180: Add properties to qfprom for fuse blowing Douglas Anderson
@ 2020-07-14 22:49 ` Doug Anderson
  2020-07-20  9:05 ` Srinivas Kandagatla
  5 siblings, 0 replies; 7+ messages in thread
From: Doug Anderson @ 2020-07-14 22:49 UTC (permalink / raw)
  To: Srinivas Kandagatla, Rob Herring, Bjorn Andersson, Andy Gross
  Cc: sparate, Sai Prakash Ranjan, mturney, linux-arm-msm,
	Jeffrey Hugo, dhavalp, Rajendra Nayak, mkurumel,
	Ravi Kumar Bokka,
	open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, LKML

Srinivas,

On Fri, Jul 10, 2020 at 7:35 AM Douglas Anderson <dianders@chromium.org> wrote:
>
> This series enables blowing of fuses on Qualcomm SoCs by extending the
> existing qfprom driver with write support.
>
> A few notes:
> - Though I don't have any firsthand knowledge of it, it's my
>   understanding that these changes could be used on any Qualcomm SoC.
>   However, it's likely not very useful on most boards because the
>   bootloader protects against this.  Thus the write support here is
>   likely only useful with a cooperating bootloader.
> - Blowing fuses is truly a one-way process.  If you mess around with
>   this and do something wrong you could irreparably brick your chip.
>   You have been warned.
>
> Versions 1 and 2 of this series were posted by Ravi Kumar Bokka.  I
> posted version 3 containing my changes / fixups with his consent.  I
> have left authorship as Ravi but added my own Signed-off-by.
>
> Version 4 is a minor spin over version 3.
>
> Version 5 is an even more minor spin and just bumps up some timings to
> fix a failure reported by Ravi on one device.  I've collected Rob
> Herring's reviews and (as far as I know) this is ready to land.
>
> Changes in v5:
> - QFPROM_FUSE_BLOW_POLL_US 10 => 100
> - QFPROM_FUSE_BLOW_TIMEOUT_US 100 => 1000
>
> Changes in v4:
> - Maintainer now listed as Srinivas.
> - Example under "soc" to get #address-cells and #size-cells.
> - Clock name is "core", not "sec".
> - Example under "soc" to get #address-cells and #size-cells.
> - Only get clock/regulator if all address ranges are provided.
> - Don't use optional version of clk_get now.
> - Clock name is "core", not "sec".
> - Cleaned up error message if couldn't get clock.
> - Fixed up minor version mask.
> - Use GENMASK to generate masks.
> - Clock name is "core", not "sec".
>
> Changes in v3:
> - Split conversion to yaml into separate patch new in v3.
> - Use 'const' for compatible instead of a 1-entry enum.
> - Changed filename to match compatible string.
> - Add #address-cells and #size-cells to list of properties.
> - Fixed up example.
> - Add an extra reg range (at 0x6000 offset for SoCs checked)
> - Define two options for reg: 1 item or 4 items.
> - No reg-names.
> - Add "clocks" and "clock-names" to list of properties.
> - Clock is now "sec", not "secclk".
> - Add "vcc-supply" to list of properties.
> - Fixed up example.
> - Don't provide "reset" value for things; just save/restore.
> - Use the major/minor version read from 0x6000.
> - Reading should still read "corrected", not "raw".
> - Added a sysfs knob to allow you to read "raw" instead of "corrected"
> - Simplified the SoC data structure.
> - No need for quite so many levels of abstraction for clocks/regulator.
> - Don't set regulator voltage.  Rely on device tree to make sure it's right.
> - Properly undo things in the case of failure.
> - Don't just keep enabling the regulator over and over again.
> - Enable / disable the clock each time
> - Polling every 100 us but timing out in 10 us didn't make sense; swap.
> - No reason for 100 us to be SoC specific.
> - No need for reg-names.
> - We shouldn't be creating two separate nvmem devices.
> - Name is now 'efuse' to match what schema checker wants.
> - Reorganized ranges to match driver/bindings changes.
> - Added 4th range as per driver/binding changes.
> - No more reg-names as per driver/binding changes.
> - Clock name is now just "sec" as per driver/binding changes.
>
> Ravi Kumar Bokka (4):
>   dt-bindings: nvmem: qfprom: Convert to yaml
>   dt-bindings: nvmem: Add properties needed for blowing fuses
>   nvmem: qfprom: Add fuse blowing support
>   arm64: dts: qcom: sc7180: Add properties to qfprom for fuse blowing
>
>  .../bindings/nvmem/qcom,qfprom.yaml           |  96 ++++++
>  .../devicetree/bindings/nvmem/qfprom.txt      |  35 --
>  arch/arm64/boot/dts/qcom/sc7180-idp.dts       |   4 +
>  arch/arm64/boot/dts/qcom/sc7180.dtsi          |  10 +-
>  drivers/nvmem/qfprom.c                        | 314 +++++++++++++++++-
>  5 files changed, 411 insertions(+), 48 deletions(-)

I know it's a little early to ping and that folks are busy, but I'm
getting to a bit of a time crunch to land this driver in the Chrome OS
kernel tree.  I'd prefer for it to land upstream first so I can pick
exactly what landed but if not then I'll just pick what I posted to
the mailing list.

Any chance you can give an approximate timeline for when it might land
so I can either wait a little while longer or stop waiting and just
take what I posted to the lists?

Thanks!  :-)

-Doug

^ permalink raw reply	[flat|nested] 7+ messages in thread

* Re: [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs
  2020-07-10 14:35 [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Douglas Anderson
                   ` (4 preceding siblings ...)
  2020-07-14 22:49 ` [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Doug Anderson
@ 2020-07-20  9:05 ` Srinivas Kandagatla
  5 siblings, 0 replies; 7+ messages in thread
From: Srinivas Kandagatla @ 2020-07-20  9:05 UTC (permalink / raw)
  To: Douglas Anderson, Rob Herring, Bjorn Andersson, Andy Gross
  Cc: sparate, saiprakash.ranjan, mturney, linux-arm-msm, Jeffrey Hugo,
	dhavalp, rnayak, mkurumel, Ravi Kumar Bokka, devicetree,
	linux-kernel



On 10/07/2020 15:35, Douglas Anderson wrote:
> This series enables blowing of fuses on Qualcomm SoCs by extending the
> existing qfprom driver with write support.
> 
> A few notes:
> - Though I don't have any firsthand knowledge of it, it's my
>    understanding that these changes could be used on any Qualcomm SoC.
>    However, it's likely not very useful on most boards because the
>    bootloader protects against this.  Thus the write support here is
>    likely only useful with a cooperating bootloader.
> - Blowing fuses is truly a one-way process.  If you mess around with
>    this and do something wrong you could irreparably brick your chip.
>    You have been warned.
> 
> Versions 1 and 2 of this series were posted by Ravi Kumar Bokka.  I
> posted version 3 containing my changes / fixups with his consent.  I
> have left authorship as Ravi but added my own Signed-off-by.
> 
> Version 4 is a minor spin over version 3.
> 
> Version 5 is an even more minor spin and just bumps up some timings to
> fix a failure reported by Ravi on one device.  I've collected Rob
> Herring's reviews and (as far as I know) this is ready to land.
> 
> Changes in v5:
> - QFPROM_FUSE_BLOW_POLL_US 10 => 100
> - QFPROM_FUSE_BLOW_TIMEOUT_US 100 => 1000
> 
> Changes in v4:
> - Maintainer now listed as Srinivas.
> - Example under "soc" to get #address-cells and #size-cells.
> - Clock name is "core", not "sec".
> - Example under "soc" to get #address-cells and #size-cells.
> - Only get clock/regulator if all address ranges are provided.
> - Don't use optional version of clk_get now.
> - Clock name is "core", not "sec".
> - Cleaned up error message if couldn't get clock.
> - Fixed up minor version mask.
> - Use GENMASK to generate masks.
> - Clock name is "core", not "sec".
> 
> Changes in v3:
> - Split conversion to yaml into separate patch new in v3.
> - Use 'const' for compatible instead of a 1-entry enum.
> - Changed filename to match compatible string.
> - Add #address-cells and #size-cells to list of properties.
> - Fixed up example.
> - Add an extra reg range (at 0x6000 offset for SoCs checked)
> - Define two options for reg: 1 item or 4 items.
> - No reg-names.
> - Add "clocks" and "clock-names" to list of properties.
> - Clock is now "sec", not "secclk".
> - Add "vcc-supply" to list of properties.
> - Fixed up example.
> - Don't provide "reset" value for things; just save/restore.
> - Use the major/minor version read from 0x6000.
> - Reading should still read "corrected", not "raw".
> - Added a sysfs knob to allow you to read "raw" instead of "corrected"
> - Simplified the SoC data structure.
> - No need for quite so many levels of abstraction for clocks/regulator.
> - Don't set regulator voltage.  Rely on device tree to make sure it's right.
> - Properly undo things in the case of failure.
> - Don't just keep enabling the regulator over and over again.
> - Enable / disable the clock each time
> - Polling every 100 us but timing out in 10 us didn't make sense; swap.
> - No reason for 100 us to be SoC specific.
> - No need for reg-names.
> - We shouldn't be creating two separate nvmem devices.
> - Name is now 'efuse' to match what schema checker wants.
> - Reorganized ranges to match driver/bindings changes.
> - Added 4th range as per driver/binding changes.
> - No more reg-names as per driver/binding changes.
> - Clock name is now just "sec" as per driver/binding changes.
> 
> Ravi Kumar Bokka (4):
>    dt-bindings: nvmem: qfprom: Convert to yaml
>    dt-bindings: nvmem: Add properties needed for blowing fuses
>    nvmem: qfprom: Add fuse blowing support

Applied above 3 with merge conflict fixed.
dts patches should go via arm-soc tree, Bjorn could pick that up!


Thanks,
srini
>    arm64: dts: qcom: sc7180: Add properties to qfprom for fuse blowing
> 
>   .../bindings/nvmem/qcom,qfprom.yaml           |  96 ++++++
>   .../devicetree/bindings/nvmem/qfprom.txt      |  35 --
>   arch/arm64/boot/dts/qcom/sc7180-idp.dts       |   4 +
>   arch/arm64/boot/dts/qcom/sc7180.dtsi          |  10 +-
>   drivers/nvmem/qfprom.c                        | 314 +++++++++++++++++-
>   5 files changed, 411 insertions(+), 48 deletions(-)
>   create mode 100644 Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
>   delete mode 100644 Documentation/devicetree/bindings/nvmem/qfprom.txt
> 

^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, other threads:[~2020-07-20  9:05 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-07-10 14:35 [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Douglas Anderson
2020-07-10 14:35 ` [PATCH v5 1/4] dt-bindings: nvmem: qfprom: Convert to yaml Douglas Anderson
2020-07-10 14:35 ` [PATCH v5 2/4] dt-bindings: nvmem: Add properties needed for blowing fuses Douglas Anderson
2020-07-10 14:35 ` [PATCH v5 3/4] nvmem: qfprom: Add fuse blowing support Douglas Anderson
2020-07-10 14:35 ` [PATCH v5 4/4] arm64: dts: qcom: sc7180: Add properties to qfprom for fuse blowing Douglas Anderson
2020-07-14 22:49 ` [PATCH v5 0/4] nvmem: qfprom: Patches for fuse blowing on Qualcomm SoCs Doug Anderson
2020-07-20  9:05 ` Srinivas Kandagatla

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®