From: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
To: Matthias Brugger <matthias.bgg@gmail.com>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: <Project_Global_Chrome_Upstream_Group@mediatek.com>,
<devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>,
<linux-mediatek@lists.infradead.org>,
"Chen-Yu Tsai" <wenst@chromium.org>,
Ryder Lee <ryder.lee@kernel.org>, <hsinyi@chromium.org>,
Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Subject: [PATCH v9 0/4] Add basic node support for MediaTek MT8186 SoC
Date: Fri, 6 May 2022 17:38:39 +0800 [thread overview]
Message-ID: <20220506093843.29030-1-allen-kh.cheng@mediatek.com> (raw)
MT8186 is a SoC based on 64bit ARMv8 architecture.
It contains 6 CA55 and 2 CA78 cores.
MT8186 share many HW IP with MT65xx series.
This patchset was tested on MT8186 evaluation board to shell.
Based on matthias/, v5.18-next/dts64. and add the below PATCHs
- dt-bindings: ARM: MediaTek: Add new document bindings of MT8186 clock
from f113a51aa2cfbd22c376d8722b5c9fef469be162
in kernel/git/clk/linux.git, clk-next
- dt-bindings: watchdog: Add compatible for MediaTek MT8186 from
ec41c6d93df6ab625140611caf7bea7e1916ae9b
in kernel/git/groeck/linux-staging.git, watchdog-next
- dt-bindings: reset: mt8186: add reset-controller header file from
78915fdfae188e23bd68d19a0f7fe7d87db57e9a
in kernel/git/groeck/linux-staging.git, watchdog-next
changes since v8:
- change name from pins_bus to pins-sda-scl
- correct email address
- add capacity-dmips-mhz for each CPU
- add ppi-partitions in gic node
- change name to power-domain
- remove status "okay" in scp node
- update timer and pericfg compatible in series
changes since v7:
- add scp&auxadc node
changes since v6:
- remove unnecessary blank line
changes since v5:
- replace Mediatek a to MediaTek
- use GPL-2.0-only OR BSD-2-Clause
changes since v4:
- correct driver clock of mt8186
- add power domains controller and clock controllers
- add pinctrl, usb host, spi and i2c nodes
- add node status in mt8186-evb.dts
- correct some dtbs_check warnings
changes since v3:
- remove serial, mmc and phy patch from series. (already merged)
- remove mcusysoff node
- move oscillator nodes at the head of dts
- change name from usb-phy to t-phy
changes since v2:
- add soc {} in mt8186.dtsi
changes since v1:
- add dt-bindings: arm: Add compatible for MediaTek MT8186
Allen-KH Cheng (4):
dt-bindings: timer: Add compatible for Mediatek MT8186
dt-bindings: arm: mediatek: Add mt8186 pericfg compatible
dt-bindings: arm: Add compatible for MediaTek MT8186
arm64: dts: Add MediaTek SoC MT8186 dts and evaluation board and
Makefile
.../devicetree/bindings/arm/mediatek.yaml | 4 +
.../arm/mediatek/mediatek,pericfg.yaml | 1 +
.../bindings/timer/mediatek,mtk-timer.txt | 1 +
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt8186-evb.dts | 232 +++++
arch/arm64/boot/dts/mediatek/mt8186.dtsi | 975 ++++++++++++++++++
6 files changed, 1214 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8186.dtsi
--
2.18.0
next reply other threads:[~2022-05-06 9:38 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-05-06 9:38 Allen-KH Cheng [this message]
2022-05-06 9:38 ` [PATCH v9 1/4] dt-bindings: timer: Add compatible for Mediatek MT8186 Allen-KH Cheng
2022-05-06 9:38 ` [PATCH v9 2/4] dt-bindings: arm: mediatek: Add mt8186 pericfg compatible Allen-KH Cheng
2022-05-06 9:38 ` [PATCH v9 3/4] dt-bindings: arm: Add compatible for MediaTek MT8186 Allen-KH Cheng
2022-05-06 9:38 ` [PATCH v9 4/4] arm64: dts: Add MediaTek SoC MT8186 dts and evaluation board and Makefile Allen-KH Cheng
2022-05-09 11:09 ` Rex-BC Chen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220506093843.29030-1-allen-kh.cheng@mediatek.com \
--to=allen-kh.cheng@mediatek.com \
--cc=Project_Global_Chrome_Upstream_Group@mediatek.com \
--cc=devicetree@vger.kernel.org \
--cc=hsinyi@chromium.org \
--cc=krzysztof.kozlowski@canonical.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=robh+dt@kernel.org \
--cc=ryder.lee@kernel.org \
--cc=wenst@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®