[PATCH RESEND 0/6] J721S2: Add support for additional IPs

[PATCH RESEND 0/6] J721S2: Add support for additional IPs

[Matt Ranostay]

The following series of patches add support for the following
on J721S2 common processor board,

- USB
- SerDes
- OSPI

Aswath Govindraju (6):
  arm64: dts: ti: k3-j721s2-main: Add support for USB
  arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node
  arm64: dts: ti: k3-j721s2-mcu-wakeup: Add support of OSPI
  arm64: dts: ti: k3-j721s2-common-proc-board: Enable SERDES0
  arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support
  arm64: dts: k3-j721s2: Add support for OSPI Flashes

 .../dts/ti/k3-j721s2-common-proc-board.dts    |  78 ++++++++++++
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi    | 112 ++++++++++++++++++
 .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi     |  40 +++++++
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi  |  42 +++++++
 4 files changed, 272 insertions(+)

-- 
2.36.1

[PATCH RESEND 1/6] arm64: dts: ti: k3-j721s2-main: Add support for USB

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add support for single instance of USB 3.0 controller in J721S2 SoC.

Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 34e7d577ae13..f7e359da8690 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -26,6 +26,20 @@ l3cache-sram@200000 {
 		};
 	};
 
+	scm_conf: scm-conf@104000 {
+		compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+		reg = <0x00 0x00104000 0x00 0x18000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x00104000 0x18000>;
+
+		usb_serdes_mux: mux-controller@0 {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
+		};
+	};
+
 	gic500: interrupt-controller@1800000 {
 		compatible = "arm,gic-v3";
 		#address-cells = <2>;
@@ -686,6 +700,34 @@ cpts@310d0000 {
 		};
 	};
 
+	usbss0: cdns-usb@4104000 {
+		compatible = "ti,j721e-usb";
+		reg = <0x00 0x04104000 0x00 0x100>;
+		clocks = <&k3_clks 360 16>, <&k3_clks 360 15>;
+		clock-names = "ref", "lpm";
+		assigned-clocks = <&k3_clks 360 16>; /* USB2_REFCLK */
+		assigned-clock-parents = <&k3_clks 360 17>;
+		power-domains = <&k3_pds 360 TI_SCI_PD_EXCLUSIVE>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		dma-coherent;
+
+		usb0: usb@6000000 {
+			compatible = "cdns,usb3";
+			reg = <0x00 0x06000000 0x00 0x10000>,
+			      <0x00 0x06010000 0x00 0x10000>,
+			      <0x00 0x06020000 0x00 0x10000>;
+			reg-names = "otg", "xhci", "dev";
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host", "peripheral", "otg";
+			maximum-speed = "super-speed";
+			dr_mode = "otg";
+		};
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.36.1

[PATCH RESEND 2/6] arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add dt node for the single instance of WIZ (SERDES wrapper) and
SERDES module shared by PCIe, eDP and USB.

Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 70 ++++++++++++++++++++++
 1 file changed, 70 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index f7e359da8690..f1e02d896168 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -5,6 +5,13 @@
  * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
  */
 
+/ {
+	serdes_refclk: serdes-refclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+	};
+};
+
 &cbass_main {
 	msmc_ram: sram@70000000 {
 		compatible = "mmio-sram";
@@ -33,6 +40,13 @@ scm_conf: scm-conf@104000 {
 		#size-cells = <1>;
 		ranges = <0x00 0x00 0x00104000 0x18000>;
 
+		serdes_ln_ctrl: mux-controller@80 {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */
+					<0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */
+		};
+
 		usb_serdes_mux: mux-controller@0 {
 			compatible = "mmio-mux";
 			#mux-control-cells = <1>;
@@ -728,6 +742,62 @@ usb0: usb@6000000 {
 		};
 	};
 
+	serdes_wiz0: wiz@5060000 {
+		compatible = "ti,j721e-wiz-10g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		num-lanes = <4>;
+		#reset-cells = <1>;
+		ranges = <0x5060000 0x0 0x5060000 0x10000>;
+
+		assigned-clocks = <&k3_clks 365 3>;
+		assigned-clock-parents = <&k3_clks 365 7>;
+
+		wiz0_pll0_refclk: pll0-refclk {
+			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
+			clock-output-names = "wiz0_pll0_refclk";
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_pll0_refclk>;
+			assigned-clock-parents = <&k3_clks 365 3>;
+		};
+
+		wiz0_pll1_refclk: pll1-refclk {
+			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
+			clock-output-names = "wiz0_pll1_refclk";
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_pll1_refclk>;
+			assigned-clock-parents = <&k3_clks 365 3>;
+		};
+
+		wiz0_refclk_dig: refclk-dig {
+			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
+			clock-output-names = "wiz0_refclk_dig";
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_refclk_dig>;
+			assigned-clock-parents = <&k3_clks 365 3>;
+		};
+
+		wiz0_cmn_refclk_dig_div: cmn-refclk-dig-div {
+			clocks = <&wiz0_refclk_dig>;
+			#clock-cells = <0>;
+		};
+
+		serdes0: serdes@5060000 {
+			compatible = "ti,j721e-serdes-10g";
+			reg = <0x05060000 0x00010000>;
+			reg-names = "torrent_phy";
+			resets = <&serdes_wiz0 0>;
+			reset-names = "torrent_reset";
+			clocks = <&wiz0_pll0_refclk>;
+			clock-names = "refclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.36.1

[PATCH RESEND 3/6] arm64: dts: ti: k3-j721s2-mcu-wakeup: Add support of OSPI

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add support for two instance of OSPI in J721S2 SoC.

Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi     | 40 +++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
index 4d1bfabd1313..7bc268f27030 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -299,4 +299,44 @@ cpts@3d000 {
 			ti,cpts-periodic-outputs = <2>;
 		};
 	};
+
+	fss: syscon@47000000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x47000000 0x0 0x100>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ospi0: spi@47040000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x47040000 0x00 0x100>,
+			      <0x5 0x0000000 0x1 0x0000000>;
+			interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 109 5>;
+			assigned-clocks = <&k3_clks 109 5>;
+			assigned-clock-parents = <&k3_clks 109 7>;
+			assigned-clock-rates = <166666666>;
+			power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		ospi1: spi@47050000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x47050000 0x00 0x100>,
+			      <0x7 0x0000000 0x1 0x0000000>;
+			interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 110 5>;
+			power-domains = <&k3_pds 110 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+	};
 };
-- 
2.36.1

[PATCH RESEND 4/6] arm64: dts: ti: k3-j721s2-common-proc-board: Enable SERDES0

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Configure first lane to PCIe, the second lane to USB and the last two lanes
to eDP. Also, add sub-nodes to SERDES0 DT node to represent SERDES0 is
connected to PCIe.

Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index b210cc07c539..791f235bd95f 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -9,6 +9,9 @@
 
 #include "k3-j721s2-som-p0.dtsi"
 #include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/mux/ti-serdes.h>
 
 / {
 	compatible = "ti,j721s2-evm", "ti,j721s2";
@@ -350,6 +353,25 @@ &cpsw_port1 {
 	phy-handle = <&phy0>;
 };
 
+&serdes_ln_ctrl {
+	idle-states = <J721S2_SERDES0_LANE0_PCIE1_LANE0>, <J721S2_SERDES0_LANE1_USB>,
+		      <J721S2_SERDES0_LANE2_EDP_LANE2>, <J721S2_SERDES0_LANE3_EDP_LANE3>;
+};
+
+&serdes_refclk {
+	clock-frequency = <100000000>;
+};
+
+&serdes0 {
+	serdes0_pcie_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz0 1>;
+	};
+};
+
 &mcu_mcan0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_mcan0_pins_default>;
-- 
2.36.1

[PATCH RESEND 5/6] arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

The board uses lane 1 of SERDES for USB. Set the mux
accordingly.

The USB controller and EVM supports super-speed for USB0
on the Type-C port. However, the SERDES has a limitation
that upto 2 protocols can be used at a time. The SERDES is
wired for PCIe, eDP and USB super-speed. It has been
chosen to use PCIe and eDP as default. So restrict
USB0 to high-speed mode.

Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 22 +++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index 791f235bd95f..aa75dc541842 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -147,6 +147,12 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
 			J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
 		>;
 	};
+
+	main_usbss0_pins_default: main-usbss0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
+		>;
+	};
 };
 
 &wkup_pmx0 {
@@ -372,6 +378,22 @@ serdes0_pcie_link: phy@0 {
 	};
 };
 
+&usb_serdes_mux {
+	idle-states = <1>; /* USB0 to SERDES lane 1 */
+};
+
+&usbss0 {
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	pinctrl-names = "default";
+	ti,vbus-divider;
+	ti,usb2-only;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "high-speed";
+};
+
 &mcu_mcan0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_mcan0_pins_default>;
-- 
2.36.1

[PATCH RESEND 6/6] arm64: dts: k3-j721s2: Add support for OSPI Flashes

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

J721S2 has an OSPI NOR flash on its SOM connected the OSPI0 instance and a
QSPI NOR flash on the common processor board connected to the OSPI1
instance. Add support for the same

Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j721s2-common-proc-board.dts    | 34 +++++++++++++++
 arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi  | 42 +++++++++++++++++++
 2 files changed, 76 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index aa75dc541842..cb99a97af426 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -206,6 +206,20 @@ mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
 			J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
 		>;
 	};
+
+	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
+			J721S2_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
+			J721S2_WKUP_IOPAD(0x060, PIN_OUTPUT, 0) /* (C21) MCU_OSPI1_CSn1 */
+			J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
+			J721S2_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
+			J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
+			J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
+			J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
+			J721S2_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
+		>;
+	};
 };
 
 &main_gpio2 {
@@ -394,6 +408,26 @@ &usb0 {
 	maximum-speed = "high-speed";
 };
 
+&ospi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+
+	flash@0{
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <40000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
 &mcu_mcan0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_mcan0_pins_default>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 76f0ceacb6d4..a05c17dd69b6 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -39,6 +39,28 @@ transceiver0: can-phy0 {
 	};
 };
 
+&wkup_pmx0 {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+			J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+			J721S2_WKUP_IOPAD(0x030, PIN_OUTPUT, 0) /* (G17) MCU_OSPI0_CSn1 */
+			J721S2_WKUP_IOPAD(0x038, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */
+			J721S2_WKUP_IOPAD(0x03c, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */
+			J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+			J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+			J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+			J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+			J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+			J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+			J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+			J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+			J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+			J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
+		>;
+	};
+};
+
 &main_pmx0 {
 	main_i2c0_pins_default: main-i2c0-pins-default {
 		pinctrl-single,pins = <
@@ -78,6 +100,26 @@ &main_mcan16 {
 	phys = <&transceiver0>;
 };
 
+&ospi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
 &mailbox0_cluster0 {
 	status = "disabled";
 };
-- 
2.36.1

[PATCH RESEND 1/6] arm64: dts: ti: k3-j721s2-main: Add support for USB

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add support for single instance of USB 3.0 controller in J721S2 SoC.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 42 ++++++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index 34e7d577ae13..f7e359da8690 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -26,6 +26,20 @@ l3cache-sram@200000 {
 		};
 	};
 
+	scm_conf: scm-conf@104000 {
+		compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+		reg = <0x00 0x00104000 0x00 0x18000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x00104000 0x18000>;
+
+		usb_serdes_mux: mux-controller@0 {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */
+		};
+	};
+
 	gic500: interrupt-controller@1800000 {
 		compatible = "arm,gic-v3";
 		#address-cells = <2>;
@@ -686,6 +700,34 @@ cpts@310d0000 {
 		};
 	};
 
+	usbss0: cdns-usb@4104000 {
+		compatible = "ti,j721e-usb";
+		reg = <0x00 0x04104000 0x00 0x100>;
+		clocks = <&k3_clks 360 16>, <&k3_clks 360 15>;
+		clock-names = "ref", "lpm";
+		assigned-clocks = <&k3_clks 360 16>; /* USB2_REFCLK */
+		assigned-clock-parents = <&k3_clks 360 17>;
+		power-domains = <&k3_pds 360 TI_SCI_PD_EXCLUSIVE>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		dma-coherent;
+
+		usb0: usb@6000000 {
+			compatible = "cdns,usb3";
+			reg = <0x00 0x06000000 0x00 0x10000>,
+			      <0x00 0x06010000 0x00 0x10000>,
+			      <0x00 0x06020000 0x00 0x10000>;
+			reg-names = "otg", "xhci", "dev";
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host", "peripheral", "otg";
+			maximum-speed = "super-speed";
+			dr_mode = "otg";
+		};
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.36.1

[PATCH RESEND 2/6] arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node

[Matt Ranostay]

From: Aswath Govindraju <a-govindraju@ti.com>

Add dt node for the single instance of WIZ (SERDES wrapper) and
SERDES module shared by PCIe, eDP and USB.

Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Acked-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 70 ++++++++++++++++++++++
 1 file changed, 70 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
index f7e359da8690..f1e02d896168 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -5,6 +5,13 @@
  * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
  */
 
+/ {
+	serdes_refclk: serdes-refclk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+	};
+};
+
 &cbass_main {
 	msmc_ram: sram@70000000 {
 		compatible = "mmio-sram";
@@ -33,6 +40,13 @@ scm_conf: scm-conf@104000 {
 		#size-cells = <1>;
 		ranges = <0x00 0x00 0x00104000 0x18000>;
 
+		serdes_ln_ctrl: mux-controller@80 {
+			compatible = "mmio-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */
+					<0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */
+		};
+
 		usb_serdes_mux: mux-controller@0 {
 			compatible = "mmio-mux";
 			#mux-control-cells = <1>;
@@ -728,6 +742,62 @@ usb0: usb@6000000 {
 		};
 	};
 
+	serdes_wiz0: wiz@5060000 {
+		compatible = "ti,j721e-wiz-10g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		num-lanes = <4>;
+		#reset-cells = <1>;
+		ranges = <0x5060000 0x0 0x5060000 0x10000>;
+
+		assigned-clocks = <&k3_clks 365 3>;
+		assigned-clock-parents = <&k3_clks 365 7>;
+
+		wiz0_pll0_refclk: pll0-refclk {
+			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
+			clock-output-names = "wiz0_pll0_refclk";
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_pll0_refclk>;
+			assigned-clock-parents = <&k3_clks 365 3>;
+		};
+
+		wiz0_pll1_refclk: pll1-refclk {
+			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
+			clock-output-names = "wiz0_pll1_refclk";
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_pll1_refclk>;
+			assigned-clock-parents = <&k3_clks 365 3>;
+		};
+
+		wiz0_refclk_dig: refclk-dig {
+			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
+			clock-output-names = "wiz0_refclk_dig";
+			#clock-cells = <0>;
+			assigned-clocks = <&wiz0_refclk_dig>;
+			assigned-clock-parents = <&k3_clks 365 3>;
+		};
+
+		wiz0_cmn_refclk_dig_div: cmn-refclk-dig-div {
+			clocks = <&wiz0_refclk_dig>;
+			#clock-cells = <0>;
+		};
+
+		serdes0: serdes@5060000 {
+			compatible = "ti,j721e-serdes-10g";
+			reg = <0x05060000 0x00010000>;
+			reg-names = "torrent_phy";
+			resets = <&serdes_wiz0 0>;
+			reset-names = "torrent_reset";
+			clocks = <&wiz0_pll0_refclk>;
+			clock-names = "refclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.36.1

Re: [PATCH RESEND 2/6] arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node

[Vignesh Raghavendra]

On 10/08/22 15:09, Matt Ranostay wrote:
> From: Aswath Govindraju <a-govindraju@ti.com>
> 
> Add dt node for the single instance of WIZ (SERDES wrapper) and
> SERDES module shared by PCIe, eDP and USB.
> 
> Cc: Vignesh Raghavendra <vigneshr@ti.com>
> Cc: Nishanth Menon <nm@ti.com>
> Acked-by: Matt Ranostay <mranostay@ti.com>
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 70 ++++++++++++++++++++++
>  1 file changed, 70 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> index f7e359da8690..f1e02d896168 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> @@ -5,6 +5,13 @@
>   * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
>   */
>  
> +/ {
> +	serdes_refclk: serdes-refclk {

clk-X

> +		#clock-cells = <0>;
> +		compatible = "fixed-clock";
> +	};
> +};
> +
>  &cbass_main {
>  	msmc_ram: sram@70000000 {
>  		compatible = "mmio-sram";
> @@ -33,6 +40,13 @@ scm_conf: scm-conf@104000 {
>  		#size-cells = <1>;
>  		ranges = <0x00 0x00 0x00104000 0x18000>;
>  
> +		serdes_ln_ctrl: mux-controller@80 {

mux-controller-X

> +			compatible = "mmio-mux";
> +			#mux-control-cells = <1>;
> +			mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */
> +					<0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */
> +		};
> +
>  		usb_serdes_mux: mux-controller@0 {
>  			compatible = "mmio-mux";
>  			#mux-control-cells = <1>;
> @@ -728,6 +742,62 @@ usb0: usb@6000000 {
>  		};
>  	};
>  
> +	serdes_wiz0: wiz@5060000 {
> +		compatible = "ti,j721e-wiz-10g";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>;
> +		clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>;
> +		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
> +		num-lanes = <4>;
> +		#reset-cells = <1>;
> +		ranges = <0x5060000 0x0 0x5060000 0x10000>;
> +
> +		assigned-clocks = <&k3_clks 365 3>;
> +		assigned-clock-parents = <&k3_clks 365 7>;
> +
> +		wiz0_pll0_refclk: pll0-refclk {

please use generic node name clk-X here and elsewhere in the patch

> +			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
> +			clock-output-names = "wiz0_pll0_refclk";
> +			#clock-cells = <0>;
> +			assigned-clocks = <&wiz0_pll0_refclk>;
> +			assigned-clock-parents = <&k3_clks 365 3>;
> +		};
> +
> +		wiz0_pll1_refclk: pll1-refclk {

ditto

> +			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
> +			clock-output-names = "wiz0_pll1_refclk";
> +			#clock-cells = <0>;
> +			assigned-clocks = <&wiz0_pll1_refclk>;
> +			assigned-clock-parents = <&k3_clks 365 3>;
> +		};
> +
> +		wiz0_refclk_dig: refclk-dig {

ditto

> +			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
> +			clock-output-names = "wiz0_refclk_dig";
> +			#clock-cells = <0>;
> +			assigned-clocks = <&wiz0_refclk_dig>;
> +			assigned-clock-parents = <&k3_clks 365 3>;
> +		};
> +
> +		wiz0_cmn_refclk_dig_div: cmn-refclk-dig-div {

ditto

> +			clocks = <&wiz0_refclk_dig>;
> +			#clock-cells = <0>;
> +		};
> +
> +		serdes0: serdes@5060000 {
> +			compatible = "ti,j721e-serdes-10g";
> +			reg = <0x05060000 0x00010000>;
> +			reg-names = "torrent_phy";
> +			resets = <&serdes_wiz0 0>;
> +			reset-names = "torrent_reset";
> +			clocks = <&wiz0_pll0_refclk>;
> +			clock-names = "refclk";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +	};
> +
>  	main_mcan0: can@2701000 {
>  		compatible = "bosch,m_can";
>  		reg = <0x00 0x02701000 0x00 0x200>,

-- 
Regards
Vignesh

Re: [PATCH RESEND 2/6] arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node

[Matt Ranostay]

On Thu, Sep 01, 2022 at 02:15:28PM +0530, Vignesh Raghavendra wrote:
> 
> 
> On 10/08/22 15:09, Matt Ranostay wrote:
> > From: Aswath Govindraju <a-govindraju@ti.com>
> > 
> > Add dt node for the single instance of WIZ (SERDES wrapper) and
> > SERDES module shared by PCIe, eDP and USB.
> > 
> > Cc: Vignesh Raghavendra <vigneshr@ti.com>
> > Cc: Nishanth Menon <nm@ti.com>
> > Acked-by: Matt Ranostay <mranostay@ti.com>
> > Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
> > ---
> >  arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 70 ++++++++++++++++++++++
> >  1 file changed, 70 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> > index f7e359da8690..f1e02d896168 100644
> > --- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> > @@ -5,6 +5,13 @@
> >   * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
> >   */
> >  
> > +/ {
> > +	serdes_refclk: serdes-refclk {
> 
> clk-X
>

So something like 'serdes_refclk: clock-cmnrefclk' would seem to match the current
naming style of other K3 platforms (albeit except j7200).

> > +		#clock-cells = <0>;
> > +		compatible = "fixed-clock";
> > +	};
> > +};
> > +
> >  &cbass_main {
> >  	msmc_ram: sram@70000000 {
> >  		compatible = "mmio-sram";
> > @@ -33,6 +40,13 @@ scm_conf: scm-conf@104000 {
> >  		#size-cells = <1>;
> >  		ranges = <0x00 0x00 0x00104000 0x18000>;
> >  
> > +		serdes_ln_ctrl: mux-controller@80 {
> 
> mux-controller-X
> 

80 is the index into the mmio region. So should it still have @ for the node
name?

Also this is how the rest of the K3 platforms reference the mux controller.

> > +			compatible = "mmio-mux";
> > +			#mux-control-cells = <1>;
> > +			mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */
> > +					<0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */
> > +		};
> > +
> >  		usb_serdes_mux: mux-controller@0 {
> >  			compatible = "mmio-mux";
> >  			#mux-control-cells = <1>;
> > @@ -728,6 +742,62 @@ usb0: usb@6000000 {
> >  		};
> >  	};
> >  
> > +	serdes_wiz0: wiz@5060000 {
> > +		compatible = "ti,j721e-wiz-10g";
> > +		#address-cells = <1>;
> > +		#size-cells = <1>;
> > +		power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>;
> > +		clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>;
> > +		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
> > +		num-lanes = <4>;
> > +		#reset-cells = <1>;
> > +		ranges = <0x5060000 0x0 0x5060000 0x10000>;
> > +
> > +		assigned-clocks = <&k3_clks 365 3>;
> > +		assigned-clock-parents = <&k3_clks 365 7>;
> > +
> > +		wiz0_pll0_refclk: pll0-refclk {
> 
> please use generic node name clk-X here and elsewhere in the patch

So something like 'wiz0_pll0_refclk: clk-refpll0'?

- Matt

> 
> > +			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
> > +			clock-output-names = "wiz0_pll0_refclk";
> > +			#clock-cells = <0>;
> > +			assigned-clocks = <&wiz0_pll0_refclk>;
> > +			assigned-clock-parents = <&k3_clks 365 3>;
> > +		};
> > +
> > +		wiz0_pll1_refclk: pll1-refclk {
> 
> ditto
> 
> > +			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
> > +			clock-output-names = "wiz0_pll1_refclk";
> > +			#clock-cells = <0>;
> > +			assigned-clocks = <&wiz0_pll1_refclk>;
> > +			assigned-clock-parents = <&k3_clks 365 3>;
> > +		};
> > +
> > +		wiz0_refclk_dig: refclk-dig {
> 
> ditto
> 
> > +			clocks = <&k3_clks 365 3>, <&serdes_refclk>;
> > +			clock-output-names = "wiz0_refclk_dig";
> > +			#clock-cells = <0>;
> > +			assigned-clocks = <&wiz0_refclk_dig>;
> > +			assigned-clock-parents = <&k3_clks 365 3>;
> > +		};
> > +
> > +		wiz0_cmn_refclk_dig_div: cmn-refclk-dig-div {
> 
> ditto
> 
> > +			clocks = <&wiz0_refclk_dig>;
> > +			#clock-cells = <0>;
> > +		};
> > +
> > +		serdes0: serdes@5060000 {
> > +			compatible = "ti,j721e-serdes-10g";
> > +			reg = <0x05060000 0x00010000>;
> > +			reg-names = "torrent_phy";
> > +			resets = <&serdes_wiz0 0>;
> > +			reset-names = "torrent_reset";
> > +			clocks = <&wiz0_pll0_refclk>;
> > +			clock-names = "refclk";
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +		};
> > +	};
> > +
> >  	main_mcan0: can@2701000 {
> >  		compatible = "bosch,m_can";
> >  		reg = <0x00 0x02701000 0x00 0x200>,
> 
> -- 
> Regards
> Vignesh

Re: [PATCH RESEND 2/6] arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node

[Vignesh Raghavendra]

On 02/09/22 05:17, Matt Ranostay wrote:
> On Thu, Sep 01, 2022 at 02:15:28PM +0530, Vignesh Raghavendra wrote:
>>
>>
>> On 10/08/22 15:09, Matt Ranostay wrote:
>>> From: Aswath Govindraju <a-govindraju@ti.com>
>>>
>>> Add dt node for the single instance of WIZ (SERDES wrapper) and
>>> SERDES module shared by PCIe, eDP and USB.
>>>
>>> Cc: Vignesh Raghavendra <vigneshr@ti.com>
>>> Cc: Nishanth Menon <nm@ti.com>
>>> Acked-by: Matt Ranostay <mranostay@ti.com>
>>> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
>>> ---
>>>  arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 70 ++++++++++++++++++++++
>>>  1 file changed, 70 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
>>> index f7e359da8690..f1e02d896168 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
>>> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
>>> @@ -5,6 +5,13 @@
>>>   * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
>>>   */
>>>  
>>> +/ {
>>> +	serdes_refclk: serdes-refclk {
>>
>> clk-X
>>
> 

Sorry for the confusion, I meant clock-<abc>. DT specification says all
clock nodes should follow above naming convention

> So something like 'serdes_refclk: clock-cmnrefclk' would seem to match the current
> naming style of other K3 platforms (albeit except j7200).
> 

Make sense...

>>> +		#clock-cells = <0>;
>>> +		compatible = "fixed-clock";
>>> +	};
>>> +};
>>> +
>>>  &cbass_main {
>>>  	msmc_ram: sram@70000000 {
>>>  		compatible = "mmio-sram";
>>> @@ -33,6 +40,13 @@ scm_conf: scm-conf@104000 {
>>>  		#size-cells = <1>;
>>>  		ranges = <0x00 0x00 0x00104000 0x18000>;
>>>  
>>> +		serdes_ln_ctrl: mux-controller@80 {
>>
>> mux-controller-X
>>
> 
> 80 is the index into the mmio region. So should it still have @ for the node
> name?
> 

@addr can only be used with nodes that have reg property. And since
there is no reg here -> would follow mux-controller-<abc> convention.

> Also this is how the rest of the K3 platforms reference the mux controller.


We need to fix other dtsi files to drop @addr part as they are now
falling make dtbs_check

> 
>>> +			compatible = "mmio-mux";
>>> +			#mux-control-cells = <1>;
>>> +			mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */
>>> +					<0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */
>>> +		};
>>> +
>>>  		usb_serdes_mux: mux-controller@0 {
>>>  			compatible = "mmio-mux";
>>>  			#mux-control-cells = <1>;
>>> @@ -728,6 +742,62 @@ usb0: usb@6000000 {
>>>  		};
>>>  	};
>>>  
>>> +	serdes_wiz0: wiz@5060000 {
>>> +		compatible = "ti,j721e-wiz-10g";
>>> +		#address-cells = <1>;
>>> +		#size-cells = <1>;
>>> +		power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>;
>>> +		clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>;
>>> +		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
>>> +		num-lanes = <4>;
>>> +		#reset-cells = <1>;
>>> +		ranges = <0x5060000 0x0 0x5060000 0x10000>;
>>> +
>>> +		assigned-clocks = <&k3_clks 365 3>;
>>> +		assigned-clock-parents = <&k3_clks 365 7>;
>>> +
>>> +		wiz0_pll0_refclk: pll0-refclk {
>>
>> please use generic node name clk-X here and elsewhere in the patch
> 
> So something like 'wiz0_pll0_refclk: clk-refpll0'?


Sorry, clock-refpll0  perhaps

[...]

-- 
Regards
Vignesh