From: Sridharan S N <quic_sridsn@quicinc.com>
To: <agross@kernel.org>, <andersson@kernel.org>,
<konrad.dybcio@linaro.org>, <robh+dt@kernel.org>,
<krzysztof.kozlowski+dt@linaro.org>, <conor+dt@kernel.org>,
<linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>
Cc: Sridharan S N <quic_sridsn@quicinc.com>
Subject: [PATCH 1/2] arm64: dts: qcom: ipq5332: enable GPIO based LEDs and Buttons
Date: Wed, 31 May 2023 12:26:18 +0530 [thread overview]
Message-ID: <20230531065619.9181-2-quic_sridsn@quicinc.com> (raw)
In-Reply-To: <20230531065619.9181-1-quic_sridsn@quicinc.com>
Add support for wlan-2g LED on GPIO 36 and wps buttons on GPIO 35.
Signed-off-by: Sridharan S N <quic_sridsn@quicinc.com>
---
arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts | 43 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts | 43 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts | 43 +++++++++++++++++++++
3 files changed, 129 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
index 3af1d5556950..ba733b6cab06 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
+++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts
@@ -7,6 +7,8 @@
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "ipq5332.dtsi"
/ {
@@ -20,6 +22,33 @@
chosen {
stdout-path = "serial0";
};
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&gpio_keys_default>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ button-wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&gpio_leds_default>;
+ pinctrl-names = "default";
+
+ led-0 {
+ gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+ };
};
&blsp1_uart0 {
@@ -57,6 +86,20 @@
/* PINCTRL */
&tlmm {
+ gpio_keys_default: gpio-keys-default-state {
+ pins = "gpio35";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ gpio_leds_default: gpio-leds-default-state {
+ pins = "gpio36";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+
i2c_1_pins: i2c-1-state {
pins = "gpio29", "gpio30";
function = "blsp1_i2c0";
diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts b/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
index bcf3b31c20e3..5322b9ee3359 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
+++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp442.dts
@@ -7,6 +7,8 @@
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "ipq5332.dtsi"
/ {
@@ -20,6 +22,33 @@
chosen {
stdout-path = "serial0";
};
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&gpio_keys_default>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ button-wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&gpio_leds_default>;
+ pinctrl-names = "default";
+
+ led-0 {
+ gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+ };
};
&blsp1_uart0 {
@@ -71,6 +100,20 @@
/* PINCTRL */
&tlmm {
+ gpio_keys_default: gpio-keys-default-state {
+ pins = "gpio35";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ gpio_leds_default: gpio-leds-default-state {
+ pins = "gpio36";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+
i2c_1_pins: i2c-1-state {
pins = "gpio29", "gpio30";
function = "blsp1_i2c0";
diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
index 3b6a5cb8bf07..15c54dfcaf3f 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
+++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp468.dts
@@ -7,6 +7,8 @@
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "ipq5332.dtsi"
/ {
@@ -20,6 +22,33 @@
chosen {
stdout-path = "serial0";
};
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&gpio_keys_default>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ button-wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ linux,input-type = <1>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&gpio_leds_default>;
+ pinctrl-names = "default";
+
+ led-0 {
+ gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+ };
};
&blsp1_uart0 {
@@ -64,6 +93,20 @@
/* PINCTRL */
&tlmm {
+ gpio_keys_default: gpio-keys-default-state {
+ pins = "gpio35";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ gpio_leds_default: gpio-leds-default-state {
+ pins = "gpio36";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+
sdc_default_state: sdc-default-state {
clk-pins {
pins = "gpio13";
--
2.17.1
next prev parent reply other threads:[~2023-05-31 6:57 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-05-31 6:56 [PATCH 0/2] Add support for GPIO based leds and buttons Sridharan S N
2023-05-31 6:56 ` Sridharan S N [this message]
2023-05-31 7:15 ` [PATCH 1/2] arm64: dts: qcom: ipq5332: enable GPIO based LEDs and Buttons Krzysztof Kozlowski
2023-05-31 8:03 ` Sridharan S N
2023-05-31 6:56 ` [PATCH 2/2] arm64: dts: qcom: ipq9574: enable GPIO based LEDs Sridharan S N
2023-06-15 14:28 [PATCH V3 0/2] Add support for GPIO based leds and buttons on IPQ5332/9574 devices Sridharan S N
2023-06-15 14:28 ` [PATCH 1/2] arm64: dts: qcom: ipq5332: enable GPIO based LEDs and Buttons Sridharan S N
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230531065619.9181-2-quic_sridsn@quicinc.com \
--to=quic_sridsn@quicinc.com \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®