From: Esteban Blanc <eblanc@baylibre.com>
To: nm@ti.com, vigneshr@ti.com, kristo@kernel.org,
robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, u-kumar1@ti.com,
eblanc@baylibre.com, jneanne@baylibre.com,
aseketeli@baylibre.com, jpanis@baylibre.com
Subject: [PATCH v4 0/6] Add TPS6594 PMIC support on several boards
Date: Thu, 27 Jul 2023 15:09:02 +0200 [thread overview]
Message-ID: <20230727130908.10656-1-eblanc@baylibre.com> (raw)
TPS6594 is a Power Management IC which provides regulators and others
features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and
PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can
communicate through the I2C or SPI interfaces.
TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives.
This serie adds device tree nodes for TI TPS6594 PMICs found in the
following boards:
- J721EXSOMXEVM:
Link: https://www.ti.com/tool/J721EXSOMXEVM
- J721S2XSOMXEVM:
Link: https://www.ti.com/tool/J721S2XSOMXEVM
- J7200XSOMXEVM:
Link: https://www.ti.com/tool/J7200XSOMXEVM
- AM62A-SKEVM:
Link: https://www.ti.com/tool/SK-AM62A-LP
- J784S4XEVM
Link: https://www.ti.com/tool/J784S4XEVM
Changes from v3:
https://lore.kernel.org/all/20230417154832.216774-1-eblanc@baylibre.com/
- Rebased on top of v6.5-rc1.
- Change pinctrl number for irq pin as wkup_pmx0 was split on some boards.
- Use already present wkup_i2c0 node instead of creating a new one.
Changes from v2:
https://lore.kernel.org/lkml/20230414112843.1358067-1-eblanc@baylibre.com/
- Change node name as per Krzysztof review.
- Add a fix for the interrupt range of wakeup gpio used by TPS6594 pmic
on J784S4.
The interruptions of the PMIC were not working before that.
- Remove dependencies on other patch series as that was a mistake, see
https://lore.kernel.org/lkml/CRYY2V3HJ0CP.96JQ18PLZB3C@burritosblues/
Changes from v1:
https://lore.kernel.org/lkml/20230329142948.833800-1-eblanc@baylibre.com/
- Harmonize regulators names across the different boards.
- Adjust AVS voltage range.
- Remove some outdated comments.
- Add PMIC to J784S4 board.
- Compatible string modified to match dt-bindings.
- Add gpio-controller and gpio-cells properties.
Apelete Seketeli (1):
arm64: dts: ti: k3-j784s4-evm: Fix interrupt ranges for TPS6594 PMIC
Esteban Blanc (2):
arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
Jerome Neanne (2):
arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC
Julien Panis (1):
arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC
arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 95 +++++++++
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 157 ++++++++++++++
arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 163 ++++++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 ++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 104 +++++++++
.../boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 2 +-
6 files changed, 719 insertions(+), 1 deletion(-)
--
2.38.5
next reply other threads:[~2023-07-27 13:09 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-07-27 13:09 Esteban Blanc [this message]
2023-07-27 13:09 ` [PATCH v4 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs Esteban Blanc
2023-08-02 4:04 ` Kumar, Udit
2023-07-27 13:09 ` [PATCH v4 2/6] arm64: dts: ti: k3-j721s2-som-p0: " Esteban Blanc
2023-08-03 10:31 ` Kumar, Udit
2023-08-03 11:13 ` Vaishnav Achath
2023-08-03 12:43 ` Kumar, Udit
2023-07-27 13:09 ` [PATCH v4 3/6] arm64: dts: ti: k3-j721e-som-p0: " Esteban Blanc
2023-08-03 15:52 ` jerome Neanne
2023-07-27 13:09 ` [PATCH v4 4/6] arm64: dts: ti: k3-j784s4-evm: Fix interrupt ranges for TPS6594 PMIC Esteban Blanc
2023-07-27 13:09 ` [PATCH v4 5/6] arm64: dts: ti: k3-j784s4-evm: Add support " Esteban Blanc
2023-07-27 13:09 ` [PATCH v4 6/6] arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC Esteban Blanc
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230727130908.10656-1-eblanc@baylibre.com \
--to=eblanc@baylibre.com \
--cc=aseketeli@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=jneanne@baylibre.com \
--cc=jpanis@baylibre.com \
--cc=kristo@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=u-kumar1@ti.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®