* [PATCH v5 1/2] regulator: aw37503: add regulator driver for Awinic AW37503
2023-08-21 3:53 [PATCH v5 0/2] regulator: aw37503: add regulator driver for Awinic AW37503 like
@ 2023-08-21 3:53 ` like
2023-08-21 3:53 ` [PATCH v5 2/2] regulator: dt-bindings: Add " like
2023-08-22 16:33 ` [PATCH v5 0/2] regulator: aw37503: add regulator driver for " Mark Brown
2 siblings, 0 replies; 5+ messages in thread
From: like @ 2023-08-21 3:53 UTC (permalink / raw)
To: lgirdwood, broonie, robh+dt, krzysztof.kozlowski+dt, conor+dt
Cc: linux-kernel, devicetree, liweilei, liangdong, wangweidong.a, Alec Li
From: Alec Li <like@awinic.com>
Add regulator driver for the device Awinic AW37503 which is single
inductor - dual output power supply device. AW37503 device is
designed to support general positive/negative driven applications
like TFT display panels.
AW37503 regulator driver supports to enable/disable and set voltage
on its output.
Signed-off-by: Alec Li <like@awinic.com>
---
drivers/regulator/Kconfig | 8 +
drivers/regulator/Makefile | 1 +
drivers/regulator/aw37503-regulator.c | 240 ++++++++++++++++++++++++++
3 files changed, 249 insertions(+)
create mode 100644 drivers/regulator/aw37503-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 823f8e6e4801..62756526cfa2 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -178,6 +178,14 @@ config REGULATOR_ATC260X
ATC260x PMICs. This will enable support for all the software
controllable DCDC/LDO regulators.
+config REGULATOR_AW37503
+ tristate "Awinic AW37503 Dual Output Power regulators"
+ depends on I2C && GPIOLIB
+ select REGMAP_I2C
+ help
+ This driver supports AW37503 single inductor - dual output
+ power supply specifically designed for display panels.
+
config REGULATOR_AXP20X
tristate "X-POWERS AXP20X PMIC Regulators"
depends on MFD_AXP20X
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 15e0d614ff66..f0e5cf7350a4 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_REGULATOR_ARM_SCMI) += scmi-regulator.o
obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
obj-$(CONFIG_REGULATOR_ATC260X) += atc260x-regulator.o
+obj-$(CONFIG_REGULATOR_AW37503) += aw37503-regulator.o
obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
obj-$(CONFIG_REGULATOR_BD71815) += bd71815-regulator.o
diff --git a/drivers/regulator/aw37503-regulator.c b/drivers/regulator/aw37503-regulator.c
new file mode 100644
index 000000000000..e01ef6ad3eb8
--- /dev/null
+++ b/drivers/regulator/aw37503-regulator.c
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// AWINIC AW37503 Regulator Driver
+//
+// Copyright (C) 2023 awinic. All Rights Reserved
+//
+// Author: <like@awinic.com>
+
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+
+#define AW37503_REG_VPOS 0x00
+#define AW37503_REG_VNEG 0x01
+#define AW37503_REG_APPS 0x03
+#define AW37503_REG_CONTROL 0x04
+#define AW37503_REG_WPRTEN 0x21
+
+#define AW37503_VOUT_MASK 0x1F
+#define AW37503_VOUT_N_VOLTAGE 0x15
+#define AW37503_VOUT_VMIN 4000000
+#define AW37503_VOUT_VMAX 6000000
+#define AW37503_VOUT_STEP 100000
+
+#define AW37503_REG_APPS_DIS_VPOS BIT(1)
+#define AW37503_REG_APPS_DIS_VNEG BIT(0)
+
+#define AW37503_REGULATOR_ID_VPOS 0
+#define AW37503_REGULATOR_ID_VNEG 1
+#define AW37503_MAX_REGULATORS 2
+
+struct aw37503_reg_pdata {
+ struct gpio_desc *en_gpiod;
+ int ena_gpio_state;
+};
+
+struct aw37503_regulator {
+ struct device *dev;
+ struct aw37503_reg_pdata reg_pdata[AW37503_MAX_REGULATORS];
+};
+
+static int aw37503_regulator_enable(struct regulator_dev *rdev)
+{
+ struct aw37503_regulator *chip = rdev_get_drvdata(rdev);
+ int id = rdev_get_id(rdev);
+ struct aw37503_reg_pdata *rpdata = &chip->reg_pdata[id];
+ int ret;
+
+ if (!IS_ERR(rpdata->en_gpiod)) {
+ gpiod_set_value_cansleep(rpdata->en_gpiod, 1);
+ rpdata->ena_gpio_state = 1;
+ }
+
+ /* Hardware automatically enable discharge bit in enable */
+ if (rdev->constraints->active_discharge ==
+ REGULATOR_ACTIVE_DISCHARGE_DISABLE) {
+ ret = regulator_set_active_discharge_regmap(rdev, false);
+ if (ret < 0) {
+ dev_err(chip->dev, "Failed to disable active discharge: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static int aw37503_regulator_disable(struct regulator_dev *rdev)
+{
+ struct aw37503_regulator *chip = rdev_get_drvdata(rdev);
+ int id = rdev_get_id(rdev);
+ struct aw37503_reg_pdata *rpdata = &chip->reg_pdata[id];
+
+ if (!IS_ERR(rpdata->en_gpiod)) {
+ gpiod_set_value_cansleep(rpdata->en_gpiod, 0);
+ rpdata->ena_gpio_state = 0;
+ }
+
+ return 0;
+}
+
+static int aw37503_regulator_is_enabled(struct regulator_dev *rdev)
+{
+ struct aw37503_regulator *chip = rdev_get_drvdata(rdev);
+ int id = rdev_get_id(rdev);
+ struct aw37503_reg_pdata *rpdata = &chip->reg_pdata[id];
+
+ if (!IS_ERR(rpdata->en_gpiod))
+ return rpdata->ena_gpio_state;
+
+ return 1;
+}
+
+static const struct regulator_ops aw37503_regulator_ops = {
+ .enable = aw37503_regulator_enable,
+ .disable = aw37503_regulator_disable,
+ .is_enabled = aw37503_regulator_is_enabled,
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+};
+
+static int aw37503_of_parse_cb(struct device_node *np,
+ const struct regulator_desc *desc,
+ struct regulator_config *config)
+{
+ struct aw37503_regulator *chip = config->driver_data;
+ struct aw37503_reg_pdata *rpdata = &chip->reg_pdata[desc->id];
+ int ret;
+
+ rpdata->en_gpiod = devm_fwnode_gpiod_get(chip->dev, of_fwnode_handle(np),
+ "enable", GPIOD_OUT_LOW,
+ "enable");
+
+ if (IS_ERR(rpdata->en_gpiod)) {
+ ret = PTR_ERR(rpdata->en_gpiod);
+
+ /* Ignore the error other than probe defer */
+ if (ret == -EPROBE_DEFER)
+ return ret;
+ return 0;
+ }
+
+ return 0;
+}
+
+#define AW37503_REGULATOR_DESC(_id, _name) \
+ [AW37503_REGULATOR_ID_##_id] = { \
+ .name = "aw37503-"#_name, \
+ .supply_name = "vin", \
+ .id = AW37503_REGULATOR_ID_##_id, \
+ .of_match = of_match_ptr(#_name), \
+ .of_parse_cb = aw37503_of_parse_cb, \
+ .ops = &aw37503_regulator_ops, \
+ .n_voltages = AW37503_VOUT_N_VOLTAGE, \
+ .min_uV = AW37503_VOUT_VMIN, \
+ .uV_step = AW37503_VOUT_STEP, \
+ .enable_time = 500, \
+ .vsel_mask = AW37503_VOUT_MASK, \
+ .vsel_reg = AW37503_REG_##_id, \
+ .active_discharge_off = 0, \
+ .active_discharge_on = AW37503_REG_APPS_DIS_##_id, \
+ .active_discharge_mask = AW37503_REG_APPS_DIS_##_id, \
+ .active_discharge_reg = AW37503_REG_APPS, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ }
+
+static const struct regulator_desc aw_regs_desc[AW37503_MAX_REGULATORS] = {
+ AW37503_REGULATOR_DESC(VPOS, outp),
+ AW37503_REGULATOR_DESC(VNEG, outn),
+};
+
+static const struct regmap_range aw37503_no_reg_ranges[] = {
+ regmap_reg_range(AW37503_REG_CONTROL + 1,
+ AW37503_REG_WPRTEN - 1),
+};
+
+static const struct regmap_access_table aw37503_no_reg_table = {
+ .no_ranges = aw37503_no_reg_ranges,
+ .n_no_ranges = ARRAY_SIZE(aw37503_no_reg_ranges),
+};
+
+static const struct regmap_config aw37503_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = AW37503_REG_WPRTEN,
+ .rd_table = &aw37503_no_reg_table,
+ .wr_table = &aw37503_no_reg_table,
+};
+
+static int aw37503_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct aw37503_regulator *chip;
+ struct regulator_dev *rdev;
+ struct regmap *regmap;
+ struct regulator_config config = { };
+ int id;
+
+ chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
+ if (!chip)
+ return -ENOMEM;
+
+ regmap = devm_regmap_init_i2c(client, &aw37503_regmap_config);
+ if (IS_ERR(regmap))
+ return dev_err_probe(dev, PTR_ERR(regmap),
+ "Failed to init regmap\n");
+
+ i2c_set_clientdata(client, chip);
+ chip->dev = dev;
+
+ config.regmap = regmap;
+ config.dev = dev;
+ config.driver_data = chip;
+
+ for (id = 0; id < AW37503_MAX_REGULATORS; ++id) {
+ rdev = devm_regulator_register(dev, &aw_regs_desc[id],
+ &config);
+ if (IS_ERR(rdev))
+ return dev_err_probe(dev, PTR_ERR(rdev),
+ "Failed to register regulator %s\n",
+ aw_regs_desc[id].name);
+ }
+ return 0;
+}
+
+static const struct i2c_device_id aw37503_id[] = {
+ {.name = "aw37503",},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, aw37503_id);
+
+static const struct of_device_id aw37503_of_match[] = {
+ {.compatible = "awinic,aw37503",},
+ { /* Sentinel */ },
+};
+
+MODULE_DEVICE_TABLE(of, aw37503_of_match);
+
+static struct i2c_driver aw37503_i2c_driver = {
+ .driver = {
+ .name = "aw37503",
+ .of_match_table = aw37503_of_match,
+ },
+ .probe_new = aw37503_probe,
+ .id_table = aw37503_id,
+};
+
+module_i2c_driver(aw37503_i2c_driver);
+
+MODULE_DESCRIPTION("aw37503 regulator driver");
+MODULE_AUTHOR("Alec Li <like@awinic.com>");
+MODULE_LICENSE("GPL");
--
2.41.0
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH v5 2/2] regulator: dt-bindings: Add Awinic AW37503
2023-08-21 3:53 [PATCH v5 0/2] regulator: aw37503: add regulator driver for Awinic AW37503 like
2023-08-21 3:53 ` [PATCH v5 1/2] " like
@ 2023-08-21 3:53 ` like
2023-08-21 6:04 ` Krzysztof Kozlowski
2023-08-22 16:33 ` [PATCH v5 0/2] regulator: aw37503: add regulator driver for " Mark Brown
2 siblings, 1 reply; 5+ messages in thread
From: like @ 2023-08-21 3:53 UTC (permalink / raw)
To: lgirdwood, broonie, robh+dt, krzysztof.kozlowski+dt, conor+dt
Cc: linux-kernel, devicetree, liweilei, liangdong, wangweidong.a, Alec Li
From: Alec Li <like@awinic.com>
Add aw37503 regulator device-tree binding documentation.
Signed-off-by: Alec Li <like@awinic.com>
---
.../bindings/regulator/awinic,aw37503.yaml | 78 +++++++++++++++++++
1 file changed, 78 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/awinic,aw37503.yaml
diff --git a/Documentation/devicetree/bindings/regulator/awinic,aw37503.yaml b/Documentation/devicetree/bindings/regulator/awinic,aw37503.yaml
new file mode 100644
index 000000000000..c92a881ed60e
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/awinic,aw37503.yaml
@@ -0,0 +1,78 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/awinic,aw37503.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Awinic AW37503 Voltage Regulator
+
+maintainers:
+ - Alec Li <like@awinic.com>
+
+description:
+ The AW37503 are dual voltage regulator, designed to support positive/negative
+ supply for driving TFT-LCD panels. It support software-configurable output
+ switching and monitoring. The output voltages can be programmed via an I2C
+ compatible interface.
+
+properties:
+ compatible:
+ const: awinic,aw37503
+
+ reg:
+ maxItems: 1
+
+patternProperties:
+ "^out[pn]$":
+ type: object
+ $ref: regulator.yaml#
+ unevaluatedProperties: false
+ description:
+ Properties for single regulator.
+
+ properties:
+ enable-gpios:
+ maxItems: 1
+ description:
+ GPIO specifier to enable the GPIO control (on/off) for regulator.
+
+ required:
+ - regulator-name
+
+required:
+ - compatible
+ - reg
+ - outp
+ - outn
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ regulator@3e {
+ compatible = "awinic,aw37503";
+ reg = <0x3e>;
+
+ outp {
+ regulator-name = "outp";
+ regulator-boot-on;
+ regulator-always-on;
+ enable-gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+
+ outn {
+ regulator-name = "outn";
+ regulator-boot-on;
+ regulator-always-on;
+ enable-gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+ };
+ };
+ };
+...
+
--
2.41.0
^ permalink raw reply [flat|nested] 5+ messages in thread