* [PATCH v12 0/2] ARM: dts: Facebook Yosemite 4 platform
@ 2023-08-28 6:51 Delphine CC Chiu
2023-08-28 6:51 ` [PATCH v12 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board Delphine CC Chiu
2023-08-28 6:51 ` [PATCH v12 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC Delphine CC Chiu
0 siblings, 2 replies; 5+ messages in thread
From: Delphine CC Chiu @ 2023-08-28 6:51 UTC (permalink / raw)
To: patrick
Cc: Delphine CC Chiu, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Joel Stanley, Andrew Jeffery, devicetree, linux-arm-kernel,
linux-aspeed, linux-kernel
Add linux device tree entry related to
Yosemite 4 specific devices connected to BMC SoC.
Changelog:
v12 - Add spi gpio config
v11 - Add imux configs for i2c-mux
- Add gpio and eeprom devices
- Remove temperature-sensor 11-004a and 11-004b
- Change power-sensor ina230 to ina233
v10 - Change to 128MB flash layout from 64MB
v9 - Remove mac2/mac3 duplicated setting about no-hw-checksum
v8 - Add description of Yosemite 4
- Remove unsupported ncsi config
- Revise i2c-mux config
- Correct power sensor i2c address
- Restore i2c 11 bus-frequency to default
v7 - Revise changelog format
v6 - Change project name from yosemitev4 to yosemite4
v5 - Revise rtc setting
- Remove duplicated multi-master setting
v4 - Resend with cover letter
v3 - Revise the bootargs to stdout-path
- Revise i2c devices
v2 - Revise the DTS node name
v1 - Add binding document
Delphine CC Chiu (2):
dt-bindings: arm: aspeed: add Facebook Yosemite 4 board
ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC
.../bindings/arm/aspeed/aspeed.yaml | 1 +
arch/arm/boot/dts/aspeed/Makefile | 1 +
.../aspeed/aspeed-bmc-facebook-yosemite4.dts | 1102 +++++++++++++++++
3 files changed, 1104 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
--
2.25.1
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH v12 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board 2023-08-28 6:51 [PATCH v12 0/2] ARM: dts: Facebook Yosemite 4 platform Delphine CC Chiu @ 2023-08-28 6:51 ` Delphine CC Chiu 2023-08-28 6:51 ` [PATCH v12 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC Delphine CC Chiu 1 sibling, 0 replies; 5+ messages in thread From: Delphine CC Chiu @ 2023-08-28 6:51 UTC (permalink / raw) To: patrick, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery Cc: Delphine CC Chiu, Krzysztof Kozlowski, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel Document the new compatibles used on Facebook Yosemite 4. Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- Changelog: v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 --- Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml index e0eff4c05879..23ee325bfed0 100644 --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml @@ -79,6 +79,7 @@ properties: - facebook,elbert-bmc - facebook,fuji-bmc - facebook,greatlakes-bmc + - facebook,yosemite4-bmc - ibm,everest-bmc - ibm,rainier-bmc - ibm,tacoma-bmc -- 2.25.1 ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v12 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC 2023-08-28 6:51 [PATCH v12 0/2] ARM: dts: Facebook Yosemite 4 platform Delphine CC Chiu 2023-08-28 6:51 ` [PATCH v12 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board Delphine CC Chiu @ 2023-08-28 6:51 ` Delphine CC Chiu 2023-08-29 14:14 ` Rob Herring 1 sibling, 1 reply; 5+ messages in thread From: Delphine CC Chiu @ 2023-08-28 6:51 UTC (permalink / raw) To: patrick, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery Cc: Delphine CC Chiu, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel Add linux device tree entry for Yosemite 4 devices connected to BMC. The Yosemite 4 is a Meta multi-node server platform, based on AST2600 SoC. Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> --- Changelog: v12 - Add spi gpio config v11 - Add imux configs for i2c-mux - Add gpio and eeprom devices - Remove temperature-sensor 11-004a and 11-004b - Change power-sensor ina230 to ina233 v10 - Change to 128MB flash layout from 64MB v9 - Remove mac2/mac3 duplicated setting about no-hw-checksum v8 - Add description of Yosemite 4 - Remove unsupported ncsi config - Revise i2c-mux config - Correct power sensor i2c address - Restore i2c 11 bus-frequency to default v7 - Revise changelog format v6 - Change project name from yosemitev4 to yosemite4 v5 - Revise rtc setting - Remove duplicated multi-master setting v3 - Revise the bootargs to stdout-path - Revise i2c devices v2 - Revise the DTS node name --- arch/arm/boot/dts/aspeed/Makefile | 1 + .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 1102 +++++++++++++++++ 2 files changed, 1103 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile index c68984322a86..5b9264b823f3 100644 --- a/arch/arm/boot/dts/aspeed/Makefile +++ b/arch/arm/boot/dts/aspeed/Makefile @@ -26,6 +26,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-facebook-wedge400.dtb \ aspeed-bmc-facebook-yamp.dtb \ aspeed-bmc-facebook-yosemitev2.dtb \ + aspeed-bmc-facebook-yosemite4.dtb \ aspeed-bmc-ibm-bonnell.dtb \ aspeed-bmc-ibm-everest.dtb \ aspeed-bmc-ibm-rainier.dtb \ diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts new file mode 100644 index 000000000000..851091a512dd --- /dev/null +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts @@ -0,0 +1,1102 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +// Copyright 2022 Facebook Inc. + +/dts-v1/; +#include "aspeed-g6.dtsi" +#include <dt-bindings/gpio/aspeed-gpio.h> +#include <dt-bindings/leds/leds-pca955x.h> +#include <dt-bindings/i2c/i2c.h> + +/ { + model = "Facebook Yosemite 4 BMC"; + compatible = "facebook,yosemite4-bmc", "aspeed,ast2600"; + + aliases { + serial4 = &uart5; + serial5 = &uart6; + serial6 = &uart7; + serial7 = &uart8; + serial8 = &uart9; + + i2c16 = &imux16; + i2c17 = &imux17; + i2c18 = &imux18; + i2c19 = &imux19; + i2c20 = &imux20; + i2c21 = &imux21; + i2c22 = &imux22; + i2c23 = &imux23; + i2c24 = &imux24; + i2c25 = &imux25; + i2c26 = &imux26; + i2c27 = &imux27; + i2c28 = &imux28; + i2c29 = &imux29; + i2c30 = &imux30; + i2c31 = &imux31; + i2c32 = &imux32; + i2c33 = &imux33; + }; + + chosen { + stdout-path = "serial4:57600n8"; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x80000000>; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>, + <&adc1 0>, <&adc1 1>; + }; + + spi_gpio: spi-gpio { + status = "okay"; + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>; + gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>; + gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>; + num-chipselects = <1>; + cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>; + + tpmdev@0 { + compatible = "tcg,tpm_tis-spi"; + spi-max-frequency = <33000000>; + reg = <0>; + }; + }; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&uart6 { + status = "okay"; +}; + +&uart7 { + status = "okay"; +}; + +&uart8 { + status = "okay"; +}; + +&uart9 { + status = "okay"; +}; + +&wdt1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdtrst1_default>; + aspeed,reset-type = "soc"; + aspeed,external-signal; + aspeed,ext-push-pull; + aspeed,ext-active-high; + aspeed,ext-pulse-duration = <256>; +}; + +&mac2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii3_default>; + use-ncsi; + mlx,multi-host; +}; + +&mac3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii4_default>; + use-ncsi; + mlx,multi-host; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; + spi-rx-bus-width = <4>; + spi-max-frequency = <50000000>; +#include "openbmc-flash-layout-128.dtsi" + }; + flash@1 { + status = "okay"; + m25p,fast-read; + label = "bmc2"; + spi-rx-bus-width = <4>; + spi-max-frequency = <50000000>; + }; +}; + +&i2c0 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c1 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c2 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c3 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c4 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c5 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c6 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c7 { + status = "okay"; + mctp-controller; + bus-frequency = <400000>; + multi-master; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + power-sensor@40 { + compatible = "adi,adm1278"; + reg = <0x40>; + }; +}; + +&i2c8 { + status = "okay"; + bus-frequency = <400000>; + i2c-mux@70 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x70>; + + imux16: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + gpio@20 { + compatible = "nxp,pca9506"; + reg = <0x20>; + }; + + gpio@21 { + compatible = "nxp,pca9506"; + reg = <0x21>; + }; + + gpio@22 { + compatible = "nxp,pca9506"; + reg = <0x22>; + }; + + gpio@23 { + compatible = "nxp,pca9506"; + reg = <0x23>; + }; + + gpio@49 { + compatible = "nxp,pca9537"; + reg = <0x49>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@54 { + compatible = "atmel,24c128"; + reg = <0x54>; + }; + }; + + imux17: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + gpio@20 { + compatible = "nxp,pca9506"; + reg = <0x20>; + }; + + gpio@21 { + compatible = "nxp,pca9506"; + reg = <0x21>; + }; + + gpio@22 { + compatible = "nxp,pca9506"; + reg = <0x22>; + }; + + gpio@23 { + compatible = "nxp,pca9506"; + reg = <0x23>; + }; + + gpio@49 { + compatible = "nxp,pca9537"; + reg = <0x49>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@54 { + compatible = "atmel,24c128"; + reg = <0x54>; + }; + }; + + imux18: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + gpio@20 { + compatible = "nxp,pca9506"; + reg = <0x20>; + }; + + gpio@21 { + compatible = "nxp,pca9506"; + reg = <0x21>; + }; + + gpio@22 { + compatible = "nxp,pca9506"; + reg = <0x22>; + }; + + gpio@23 { + compatible = "nxp,pca9506"; + reg = <0x23>; + }; + + gpio@49 { + compatible = "nxp,pca9537"; + reg = <0x49>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@54 { + compatible = "atmel,24c128"; + reg = <0x54>; + }; + }; + + imux19: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + gpio@20 { + compatible = "nxp,pca9506"; + reg = <0x20>; + }; + + gpio@21 { + compatible = "nxp,pca9506"; + reg = <0x21>; + }; + + gpio@22 { + compatible = "nxp,pca9506"; + reg = <0x22>; + }; + + gpio@23 { + compatible = "nxp,pca9506"; + reg = <0x23>; + }; + + gpio@49 { + compatible = "nxp,pca9537"; + reg = <0x49>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@54 { + compatible = "atmel,24c128"; + reg = <0x54>; + }; + }; + }; +}; + +&i2c9 { + status = "okay"; + bus-frequency = <400000>; + i2c-mux@71 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x71>; + + imux20: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + gpio@20 { + compatible = "nxp,pca9506"; + reg = <0x20>; + }; + + gpio@21 { + compatible = "nxp,pca9506"; + reg = <0x21>; + }; + + gpio@22 { + compatible = "nxp,pca9506"; + reg = <0x22>; + }; + + gpio@23 { + compatible = "nxp,pca9506"; + reg = <0x23>; + }; + + gpio@49 { + compatible = "nxp,pca9537"; + reg = <0x49>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@54 { + compatible = "atmel,24c128"; + reg = <0x54>; + }; + }; + + imux21: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + gpio@20 { + compatible = "nxp,pca9506"; + reg = <0x20>; + }; + + gpio@21 { + compatible = "nxp,pca9506"; + reg = <0x21>; + }; + + gpio@22 { + compatible = "nxp,pca9506"; + reg = <0x22>; + }; + + gpio@23 { + compatible = "nxp,pca9506"; + reg = <0x23>; + }; + + gpio@49 { + compatible = "nxp,pca9537"; + reg = <0x49>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@54 { + compatible = "atmel,24c128"; + reg = <0x54>; + }; + }; + + imux22: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + gpio@20 { + compatible = "nxp,pca9506"; + reg = <0x20>; + }; + + gpio@21 { + compatible = "nxp,pca9506"; + reg = <0x21>; + }; + + gpio@22 { + compatible = "nxp,pca9506"; + reg = <0x22>; + }; + + gpio@23 { + compatible = "nxp,pca9506"; + reg = <0x23>; + }; + + gpio@49 { + compatible = "nxp,pca9537"; + reg = <0x49>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@54 { + compatible = "atmel,24c128"; + reg = <0x54>; + }; + }; + + imux23: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + gpio@20 { + compatible = "nxp,pca9506"; + reg = <0x20>; + }; + + gpio@21 { + compatible = "nxp,pca9506"; + reg = <0x21>; + }; + + gpio@22 { + compatible = "nxp,pca9506"; + reg = <0x22>; + }; + + gpio@23 { + compatible = "nxp,pca9506"; + reg = <0x23>; + }; + + gpio@49 { + compatible = "nxp,pca9537"; + reg = <0x49>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@54 { + compatible = "atmel,24c128"; + reg = <0x54>; + }; + }; + }; +}; + +&i2c10 { + status = "okay"; + bus-frequency = <400000>; + i2c-mux@74 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x74>; + + imux28: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + imux29: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + gpio@20 { + compatible = "nxp,pca9506"; + reg = <0x20>; + }; + + gpio@21 { + compatible = "nxp,pca9506"; + reg = <0x21>; + }; + + gpio@22 { + compatible = "nxp,pca9506"; + reg = <0x22>; + }; + + gpio@23 { + compatible = "nxp,pca9506"; + reg = <0x23>; + }; + + gpio@24 { + compatible = "nxp,pca9506"; + reg = <0x24>; + }; + }; + }; +}; + +&i2c11 { + status = "okay"; + power-sensor@10 { + compatible = "adi, adm1272"; + reg = <0x10>; + }; + + power-sensor@12 { + compatible = "adi, adm1272"; + reg = <0x12>; + }; + + gpio@20 { + compatible = "nxp,pca9555"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@21 { + compatible = "nxp,pca9555"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@22 { + compatible = "nxp,pca9555"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + temperature-sensor@48 { + compatible = "ti,tmp75"; + reg = <0x48>; + }; + + temperature-sensor@49 { + compatible = "ti,tmp75"; + reg = <0x49>; + }; + + eeprom@54 { + compatible = "atmel,24c256"; + reg = <0x54>; + }; +}; + +&i2c12 { + status = "okay"; + bus-frequency = <400000>; + + temperature-sensor@48 { + compatible = "ti,tmp75"; + reg = <0x48>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@54 { + compatible = "atmel,24c64"; + reg = <0x54>; + }; + + rtc@6f { + compatible = "nuvoton,nct3018y"; + reg = <0x6f>; + }; +}; + +&i2c13 { + status = "okay"; + bus-frequency = <400000>; + gpio@20 { + compatible = "nxp,pca9506"; + reg = <0x20>; + }; + + gpio@21 { + compatible = "nxp,pca9506"; + reg = <0x21>; + }; + + gpio@22 { + compatible = "nxp,pca9506"; + reg = <0x22>; + }; + + gpio@23 { + compatible = "nxp,pca9506"; + reg = <0x23>; + }; +}; + +&i2c14 { + status = "okay"; + bus-frequency = <400000>; + adc@1d { + compatible = "ti,adc128d818"; + reg = <0x1d>; + ti,mode = /bits/ 8 <2>; + }; + + adc@35 { + compatible = "ti,adc128d818"; + reg = <0x35>; + ti,mode = /bits/ 8 <2>; + }; + + adc@37 { + compatible = "ti,adc128d818"; + reg = <0x37>; + ti,mode = /bits/ 8 <2>; + }; + + power-sensor@40 { + compatible = "ti,ina233"; + reg = <0x40>; + }; + + power-sensor@41 { + compatible = "ti,ina233"; + reg = <0x41>; + }; + + power-sensor@42 { + compatible = "ti,ina233"; + reg = <0x42>; + }; + + power-sensor@43 { + compatible = "ti,ina233"; + reg = <0x43>; + }; + + power-sensor@44 { + compatible = "ti,ina233"; + reg = <0x44>; + }; + + temperature-sensor@4e { + compatible = "ti,tmp75"; + reg = <0x4e>; + }; + + temperature-sensor@4f { + compatible = "ti,tmp75"; + reg = <0x4f>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + i2c-mux@71 { + compatible = "nxp,pca9846"; + #address-cells = <1>; + #size-cells = <0>; + + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x71>; + + imux30: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc@1f { + compatible = "ti,adc128d818"; + reg = <0x1f>; + ti,mode = /bits/ 8 <2>; + }; + + pwm@20{ + compatible = "max31790"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + }; + + gpio@22{ + compatible = "ti,tca6424"; + reg = <0x22>; + }; + + pwm@23{ + compatible = "max31790"; + reg = <0x23>; + #address-cells = <1>; + #size-cells = <0>; + }; + + adc@33 { + compatible = "maxim,max11615"; + reg = <0x33>; + }; + + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; + + gpio@61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + imux31: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + adc@1f { + compatible = "ti,adc128d818"; + reg = <0x1f>; + ti,mode = /bits/ 8 <2>; + }; + + pwm@20{ + compatible = "max31790"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + }; + + gpio@22{ + compatible = "ti,tca6424"; + reg = <0x22>; + }; + + pwm@23{ + compatible = "max31790"; + reg = <0x23>; + #address-cells = <1>; + #size-cells = <0>; + }; + + adc@33 { + compatible = "maxim,max11615"; + reg = <0x33>; + }; + + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; + + gpio@61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + }; + + i2c-mux@73 { + compatible = "nxp,pca9544"; + #address-cells = <1>; + #size-cells = <0>; + + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x73>; + + imux32: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + adc@35 { + compatible = "maxim,max11617"; + reg = <0x35>; + }; + }; + + imux33: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + adc@35 { + compatible = "maxim,max11617"; + reg = <0x35>; + }; + }; + }; +}; + +&i2c15 { + status = "okay"; + mctp-controller; + multi-master; + bus-frequency = <400000>; + + mctp@10 { + compatible = "mctp-i2c-controller"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + }; + + i2c-mux@72 { + compatible = "nxp,pca9544"; + idle-state = <0>; + i2c-mux-idle-disconnect; + reg = <0x72>; + + imux24: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + imux25: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + + imux26: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + imux27: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + }; +}; + +&adc0 { + ref_voltage = <2500>; + status = "okay"; + pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default + &pinctrl_adc2_default &pinctrl_adc3_default + &pinctrl_adc4_default &pinctrl_adc5_default + &pinctrl_adc6_default &pinctrl_adc7_default>; +}; + +&adc1 { + ref_voltage = <2500>; + status = "okay"; + pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default>; +}; + + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&uhci { + status = "okay"; +}; -- 2.25.1 ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v12 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC 2023-08-28 6:51 ` [PATCH v12 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC Delphine CC Chiu @ 2023-08-29 14:14 ` Rob Herring 2023-09-01 7:55 ` Delphine_CC_Chiu/WYHQ/Wiwynn 0 siblings, 1 reply; 5+ messages in thread From: Rob Herring @ 2023-08-29 14:14 UTC (permalink / raw) To: Delphine CC Chiu Cc: patrick, Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel On Mon, Aug 28, 2023 at 1:52 AM Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> wrote: > > Add linux device tree entry for Yosemite 4 devices connected to BMC. > The Yosemite 4 is a Meta multi-node server platform, based on AST2600 SoC. This was already applied and sent upstream on Aug 10 by Joel. You'll need incremental patches. > > Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> > --- > Changelog: > v12 - Add spi gpio config > v11 - Add imux configs for i2c-mux > - Add gpio and eeprom devices > - Remove temperature-sensor 11-004a and 11-004b > - Change power-sensor ina230 to ina233 > v10 - Change to 128MB flash layout from 64MB > v9 - Remove mac2/mac3 duplicated setting about no-hw-checksum > v8 - Add description of Yosemite 4 > - Remove unsupported ncsi config > - Revise i2c-mux config > - Correct power sensor i2c address > - Restore i2c 11 bus-frequency to default > v7 - Revise changelog format > v6 - Change project name from yosemitev4 to yosemite4 > v5 - Revise rtc setting > - Remove duplicated multi-master setting > v3 - Revise the bootargs to stdout-path > - Revise i2c devices > v2 - Revise the DTS node name > --- > arch/arm/boot/dts/aspeed/Makefile | 1 + > .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 1102 +++++++++++++++++ > 2 files changed, 1103 insertions(+) > create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts > > diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile > index c68984322a86..5b9264b823f3 100644 > --- a/arch/arm/boot/dts/aspeed/Makefile > +++ b/arch/arm/boot/dts/aspeed/Makefile > @@ -26,6 +26,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ > aspeed-bmc-facebook-wedge400.dtb \ > aspeed-bmc-facebook-yamp.dtb \ > aspeed-bmc-facebook-yosemitev2.dtb \ > + aspeed-bmc-facebook-yosemite4.dtb \ > aspeed-bmc-ibm-bonnell.dtb \ > aspeed-bmc-ibm-everest.dtb \ > aspeed-bmc-ibm-rainier.dtb \ > diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts > new file mode 100644 > index 000000000000..851091a512dd > --- /dev/null > +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts > @@ -0,0 +1,1102 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +// Copyright 2022 Facebook Inc. > + > +/dts-v1/; > +#include "aspeed-g6.dtsi" > +#include <dt-bindings/gpio/aspeed-gpio.h> > +#include <dt-bindings/leds/leds-pca955x.h> > +#include <dt-bindings/i2c/i2c.h> > + > +/ { > + model = "Facebook Yosemite 4 BMC"; > + compatible = "facebook,yosemite4-bmc", "aspeed,ast2600"; > + > + aliases { > + serial4 = &uart5; > + serial5 = &uart6; > + serial6 = &uart7; > + serial7 = &uart8; > + serial8 = &uart9; > + > + i2c16 = &imux16; > + i2c17 = &imux17; > + i2c18 = &imux18; > + i2c19 = &imux19; > + i2c20 = &imux20; > + i2c21 = &imux21; > + i2c22 = &imux22; > + i2c23 = &imux23; > + i2c24 = &imux24; > + i2c25 = &imux25; > + i2c26 = &imux26; > + i2c27 = &imux27; > + i2c28 = &imux28; > + i2c29 = &imux29; > + i2c30 = &imux30; > + i2c31 = &imux31; > + i2c32 = &imux32; > + i2c33 = &imux33; > + }; > + > + chosen { > + stdout-path = "serial4:57600n8"; > + }; > + > + memory@80000000 { > + device_type = "memory"; > + reg = <0x80000000 0x80000000>; > + }; > + > + iio-hwmon { > + compatible = "iio-hwmon"; > + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, > + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>, > + <&adc1 0>, <&adc1 1>; > + }; > + > + spi_gpio: spi-gpio { > + status = "okay"; > + compatible = "spi-gpio"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>; > + gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>; > + gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>; > + num-chipselects = <1>; > + cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>; > + > + tpmdev@0 { > + compatible = "tcg,tpm_tis-spi"; > + spi-max-frequency = <33000000>; > + reg = <0>; > + }; > + }; > +}; > + > +&uart1 { > + status = "okay"; > +}; > + > +&uart2 { > + status = "okay"; > +}; > + > +&uart3 { > + status = "okay"; > +}; > + > +&uart4 { > + status = "okay"; > +}; > + > +&uart5 { > + status = "okay"; > +}; > + > +&uart6 { > + status = "okay"; > +}; > + > +&uart7 { > + status = "okay"; > +}; > + > +&uart8 { > + status = "okay"; > +}; > + > +&uart9 { > + status = "okay"; > +}; > + > +&wdt1 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_wdtrst1_default>; > + aspeed,reset-type = "soc"; > + aspeed,external-signal; > + aspeed,ext-push-pull; > + aspeed,ext-active-high; > + aspeed,ext-pulse-duration = <256>; > +}; > + > +&mac2 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_rmii3_default>; > + use-ncsi; > + mlx,multi-host; > +}; > + > +&mac3 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_rmii4_default>; > + use-ncsi; > + mlx,multi-host; > +}; > + > +&fmc { > + status = "okay"; > + flash@0 { > + status = "okay"; > + m25p,fast-read; > + label = "bmc"; > + spi-rx-bus-width = <4>; > + spi-max-frequency = <50000000>; > +#include "openbmc-flash-layout-128.dtsi" > + }; > + flash@1 { > + status = "okay"; > + m25p,fast-read; > + label = "bmc2"; > + spi-rx-bus-width = <4>; > + spi-max-frequency = <50000000>; > + }; > +}; > + > +&i2c0 { > + status = "okay"; > + mctp-controller; > + bus-frequency = <400000>; > + multi-master; > + > + mctp@10 { > + compatible = "mctp-i2c-controller"; > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > + }; > + > + power-sensor@40 { > + compatible = "adi,adm1278"; > + reg = <0x40>; > + }; > +}; > + > +&i2c1 { > + status = "okay"; > + mctp-controller; > + bus-frequency = <400000>; > + multi-master; > + > + mctp@10 { > + compatible = "mctp-i2c-controller"; > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > + }; > + > + power-sensor@40 { > + compatible = "adi,adm1278"; > + reg = <0x40>; > + }; > +}; > + > +&i2c2 { > + status = "okay"; > + mctp-controller; > + bus-frequency = <400000>; > + multi-master; > + > + mctp@10 { > + compatible = "mctp-i2c-controller"; > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > + }; > + > + power-sensor@40 { > + compatible = "adi,adm1278"; > + reg = <0x40>; > + }; > +}; > + > +&i2c3 { > + status = "okay"; > + mctp-controller; > + bus-frequency = <400000>; > + multi-master; > + > + mctp@10 { > + compatible = "mctp-i2c-controller"; > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > + }; > + > + power-sensor@40 { > + compatible = "adi,adm1278"; > + reg = <0x40>; > + }; > +}; > + > +&i2c4 { > + status = "okay"; > + mctp-controller; > + bus-frequency = <400000>; > + multi-master; > + > + mctp@10 { > + compatible = "mctp-i2c-controller"; > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > + }; > + > + power-sensor@40 { > + compatible = "adi,adm1278"; > + reg = <0x40>; > + }; > +}; > + > +&i2c5 { > + status = "okay"; > + mctp-controller; > + bus-frequency = <400000>; > + multi-master; > + > + mctp@10 { > + compatible = "mctp-i2c-controller"; > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > + }; > + > + power-sensor@40 { > + compatible = "adi,adm1278"; > + reg = <0x40>; > + }; > +}; > + > +&i2c6 { > + status = "okay"; > + mctp-controller; > + bus-frequency = <400000>; > + multi-master; > + > + mctp@10 { > + compatible = "mctp-i2c-controller"; > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > + }; > + > + power-sensor@40 { > + compatible = "adi,adm1278"; > + reg = <0x40>; > + }; > +}; > + > +&i2c7 { > + status = "okay"; > + mctp-controller; > + bus-frequency = <400000>; > + multi-master; > + > + mctp@10 { > + compatible = "mctp-i2c-controller"; > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > + }; > + > + power-sensor@40 { > + compatible = "adi,adm1278"; > + reg = <0x40>; > + }; > +}; > + > +&i2c8 { > + status = "okay"; > + bus-frequency = <400000>; > + i2c-mux@70 { > + compatible = "nxp,pca9544"; > + idle-state = <0>; > + i2c-mux-idle-disconnect; > + reg = <0x70>; > + > + imux16: i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + gpio@20 { > + compatible = "nxp,pca9506"; > + reg = <0x20>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9506"; > + reg = <0x21>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9506"; > + reg = <0x22>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9506"; > + reg = <0x23>; > + }; > + > + gpio@49 { > + compatible = "nxp,pca9537"; > + reg = <0x49>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c128"; > + reg = <0x50>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c128"; > + reg = <0x51>; > + }; > + > + eeprom@54 { > + compatible = "atmel,24c128"; > + reg = <0x54>; > + }; > + }; > + > + imux17: i2c@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <1>; > + gpio@20 { > + compatible = "nxp,pca9506"; > + reg = <0x20>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9506"; > + reg = <0x21>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9506"; > + reg = <0x22>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9506"; > + reg = <0x23>; > + }; > + > + gpio@49 { > + compatible = "nxp,pca9537"; > + reg = <0x49>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c128"; > + reg = <0x50>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c128"; > + reg = <0x51>; > + }; > + > + eeprom@54 { > + compatible = "atmel,24c128"; > + reg = <0x54>; > + }; > + }; > + > + imux18: i2c@2 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <2>; > + gpio@20 { > + compatible = "nxp,pca9506"; > + reg = <0x20>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9506"; > + reg = <0x21>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9506"; > + reg = <0x22>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9506"; > + reg = <0x23>; > + }; > + > + gpio@49 { > + compatible = "nxp,pca9537"; > + reg = <0x49>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c128"; > + reg = <0x50>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c128"; > + reg = <0x51>; > + }; > + > + eeprom@54 { > + compatible = "atmel,24c128"; > + reg = <0x54>; > + }; > + }; > + > + imux19: i2c@3 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <3>; > + gpio@20 { > + compatible = "nxp,pca9506"; > + reg = <0x20>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9506"; > + reg = <0x21>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9506"; > + reg = <0x22>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9506"; > + reg = <0x23>; > + }; > + > + gpio@49 { > + compatible = "nxp,pca9537"; > + reg = <0x49>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c128"; > + reg = <0x50>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c128"; > + reg = <0x51>; > + }; > + > + eeprom@54 { > + compatible = "atmel,24c128"; > + reg = <0x54>; > + }; > + }; > + }; > +}; > + > +&i2c9 { > + status = "okay"; > + bus-frequency = <400000>; > + i2c-mux@71 { > + compatible = "nxp,pca9544"; > + idle-state = <0>; > + i2c-mux-idle-disconnect; > + reg = <0x71>; > + > + imux20: i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + gpio@20 { > + compatible = "nxp,pca9506"; > + reg = <0x20>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9506"; > + reg = <0x21>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9506"; > + reg = <0x22>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9506"; > + reg = <0x23>; > + }; > + > + gpio@49 { > + compatible = "nxp,pca9537"; > + reg = <0x49>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c128"; > + reg = <0x50>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c128"; > + reg = <0x51>; > + }; > + > + eeprom@54 { > + compatible = "atmel,24c128"; > + reg = <0x54>; > + }; > + }; > + > + imux21: i2c@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <1>; > + gpio@20 { > + compatible = "nxp,pca9506"; > + reg = <0x20>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9506"; > + reg = <0x21>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9506"; > + reg = <0x22>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9506"; > + reg = <0x23>; > + }; > + > + gpio@49 { > + compatible = "nxp,pca9537"; > + reg = <0x49>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c128"; > + reg = <0x50>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c128"; > + reg = <0x51>; > + }; > + > + eeprom@54 { > + compatible = "atmel,24c128"; > + reg = <0x54>; > + }; > + }; > + > + imux22: i2c@2 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <2>; > + gpio@20 { > + compatible = "nxp,pca9506"; > + reg = <0x20>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9506"; > + reg = <0x21>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9506"; > + reg = <0x22>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9506"; > + reg = <0x23>; > + }; > + > + gpio@49 { > + compatible = "nxp,pca9537"; > + reg = <0x49>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c128"; > + reg = <0x50>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c128"; > + reg = <0x51>; > + }; > + > + eeprom@54 { > + compatible = "atmel,24c128"; > + reg = <0x54>; > + }; > + }; > + > + imux23: i2c@3 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <3>; > + gpio@20 { > + compatible = "nxp,pca9506"; > + reg = <0x20>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9506"; > + reg = <0x21>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9506"; > + reg = <0x22>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9506"; > + reg = <0x23>; > + }; > + > + gpio@49 { > + compatible = "nxp,pca9537"; > + reg = <0x49>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c128"; > + reg = <0x50>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c128"; > + reg = <0x51>; > + }; > + > + eeprom@54 { > + compatible = "atmel,24c128"; > + reg = <0x54>; > + }; > + }; > + }; > +}; > + > +&i2c10 { > + status = "okay"; > + bus-frequency = <400000>; > + i2c-mux@74 { > + compatible = "nxp,pca9544"; > + idle-state = <0>; > + i2c-mux-idle-disconnect; > + reg = <0x74>; > + > + imux28: i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + }; > + > + imux29: i2c@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <1>; > + gpio@20 { > + compatible = "nxp,pca9506"; > + reg = <0x20>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9506"; > + reg = <0x21>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9506"; > + reg = <0x22>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9506"; > + reg = <0x23>; > + }; > + > + gpio@24 { > + compatible = "nxp,pca9506"; > + reg = <0x24>; > + }; > + }; > + }; > +}; > + > +&i2c11 { > + status = "okay"; > + power-sensor@10 { > + compatible = "adi, adm1272"; > + reg = <0x10>; > + }; > + > + power-sensor@12 { > + compatible = "adi, adm1272"; > + reg = <0x12>; > + }; > + > + gpio@20 { > + compatible = "nxp,pca9555"; > + reg = <0x20>; > + gpio-controller; > + #gpio-cells = <2>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9555"; > + reg = <0x21>; > + gpio-controller; > + #gpio-cells = <2>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9555"; > + reg = <0x22>; > + gpio-controller; > + #gpio-cells = <2>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9555"; > + reg = <0x23>; > + gpio-controller; > + #gpio-cells = <2>; > + }; > + > + temperature-sensor@48 { > + compatible = "ti,tmp75"; > + reg = <0x48>; > + }; > + > + temperature-sensor@49 { > + compatible = "ti,tmp75"; > + reg = <0x49>; > + }; > + > + eeprom@54 { > + compatible = "atmel,24c256"; > + reg = <0x54>; > + }; > +}; > + > +&i2c12 { > + status = "okay"; > + bus-frequency = <400000>; > + > + temperature-sensor@48 { > + compatible = "ti,tmp75"; > + reg = <0x48>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c128"; > + reg = <0x50>; > + }; > + > + eeprom@54 { > + compatible = "atmel,24c64"; > + reg = <0x54>; > + }; > + > + rtc@6f { > + compatible = "nuvoton,nct3018y"; > + reg = <0x6f>; > + }; > +}; > + > +&i2c13 { > + status = "okay"; > + bus-frequency = <400000>; > + gpio@20 { > + compatible = "nxp,pca9506"; > + reg = <0x20>; > + }; > + > + gpio@21 { > + compatible = "nxp,pca9506"; > + reg = <0x21>; > + }; > + > + gpio@22 { > + compatible = "nxp,pca9506"; > + reg = <0x22>; > + }; > + > + gpio@23 { > + compatible = "nxp,pca9506"; > + reg = <0x23>; > + }; > +}; > + > +&i2c14 { > + status = "okay"; > + bus-frequency = <400000>; > + adc@1d { > + compatible = "ti,adc128d818"; > + reg = <0x1d>; > + ti,mode = /bits/ 8 <2>; > + }; > + > + adc@35 { > + compatible = "ti,adc128d818"; > + reg = <0x35>; > + ti,mode = /bits/ 8 <2>; > + }; > + > + adc@37 { > + compatible = "ti,adc128d818"; > + reg = <0x37>; > + ti,mode = /bits/ 8 <2>; > + }; > + > + power-sensor@40 { > + compatible = "ti,ina233"; > + reg = <0x40>; > + }; > + > + power-sensor@41 { > + compatible = "ti,ina233"; > + reg = <0x41>; > + }; > + > + power-sensor@42 { > + compatible = "ti,ina233"; > + reg = <0x42>; > + }; > + > + power-sensor@43 { > + compatible = "ti,ina233"; > + reg = <0x43>; > + }; > + > + power-sensor@44 { > + compatible = "ti,ina233"; > + reg = <0x44>; > + }; > + > + temperature-sensor@4e { > + compatible = "ti,tmp75"; > + reg = <0x4e>; > + }; > + > + temperature-sensor@4f { > + compatible = "ti,tmp75"; > + reg = <0x4f>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c128"; > + reg = <0x51>; > + }; > + > + i2c-mux@71 { > + compatible = "nxp,pca9846"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + idle-state = <0>; > + i2c-mux-idle-disconnect; > + reg = <0x71>; > + > + imux30: i2c@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + > + adc@1f { > + compatible = "ti,adc128d818"; > + reg = <0x1f>; > + ti,mode = /bits/ 8 <2>; > + }; > + > + pwm@20{ > + compatible = "max31790"; This is not documented. It also needs a vendor prefix. > + reg = <0x20>; > + #address-cells = <1>; > + #size-cells = <0>; These 2 are for child nodes, but you don't have any. And a PWM probably never will. Rob ^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: [PATCH v12 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC 2023-08-29 14:14 ` Rob Herring @ 2023-09-01 7:55 ` Delphine_CC_Chiu/WYHQ/Wiwynn 0 siblings, 0 replies; 5+ messages in thread From: Delphine_CC_Chiu/WYHQ/Wiwynn @ 2023-09-01 7:55 UTC (permalink / raw) To: Rob Herring, Delphine_CC_Chiu/WYHQ/Wiwynn Cc: patrick, Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel > -----Original Message----- > From: Rob Herring <robh+dt@kernel.org> > Sent: Tuesday, August 29, 2023 10:14 PM > To: Delphine_CC_Chiu/WYHQ/Wiwynn <Delphine_CC_Chiu@wiwynn.com> > Cc: patrick@stwcx.xyz; Krzysztof Kozlowski > <krzysztof.kozlowski+dt@linaro.org>; Conor Dooley <conor+dt@kernel.org>; > Joel Stanley <joel@jms.id.au>; Andrew Jeffery <andrew@aj.id.au>; > devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; > linux-aspeed@lists.ozlabs.org; linux-kernel@vger.kernel.org > Subject: Re: [PATCH v12 2/2] ARM: dts: aspeed: yosemite4: add Facebook > Yosemite 4 BMC > > Security Reminder: Please be aware that this email is sent by an external > sender. > > On Mon, Aug 28, 2023 at 1:52 AM Delphine CC Chiu > <Delphine_CC_Chiu@wiwynn.com> wrote: > > > > Add linux device tree entry for Yosemite 4 devices connected to BMC. > > The Yosemite 4 is a Meta multi-node server platform, based on AST2600 > SoC. > > This was already applied and sent upstream on Aug 10 by Joel. You'll need > incremental patches. I'll rebase the master and generate incremental patches in next time contribution, thank you for the correction. > > > > > Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> > > --- > > Changelog: > > v12 - Add spi gpio config > > v11 - Add imux configs for i2c-mux > > - Add gpio and eeprom devices > > - Remove temperature-sensor 11-004a and 11-004b > > - Change power-sensor ina230 to ina233 > > v10 - Change to 128MB flash layout from 64MB > > v9 - Remove mac2/mac3 duplicated setting about no-hw-checksum > > v8 - Add description of Yosemite 4 > > - Remove unsupported ncsi config > > - Revise i2c-mux config > > - Correct power sensor i2c address > > - Restore i2c 11 bus-frequency to default > > v7 - Revise changelog format > > v6 - Change project name from yosemitev4 to yosemite4 > > v5 - Revise rtc setting > > - Remove duplicated multi-master setting > > v3 - Revise the bootargs to stdout-path > > - Revise i2c devices > > v2 - Revise the DTS node name > > --- > > arch/arm/boot/dts/aspeed/Makefile | 1 + > > .../aspeed/aspeed-bmc-facebook-yosemite4.dts | 1102 > > +++++++++++++++++ > > 2 files changed, 1103 insertions(+) > > create mode 100644 > > arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts > > > > diff --git a/arch/arm/boot/dts/aspeed/Makefile > > b/arch/arm/boot/dts/aspeed/Makefile > > index c68984322a86..5b9264b823f3 100644 > > --- a/arch/arm/boot/dts/aspeed/Makefile > > +++ b/arch/arm/boot/dts/aspeed/Makefile > > @@ -26,6 +26,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ > > aspeed-bmc-facebook-wedge400.dtb \ > > aspeed-bmc-facebook-yamp.dtb \ > > aspeed-bmc-facebook-yosemitev2.dtb \ > > + aspeed-bmc-facebook-yosemite4.dtb \ > > aspeed-bmc-ibm-bonnell.dtb \ > > aspeed-bmc-ibm-everest.dtb \ > > aspeed-bmc-ibm-rainier.dtb \ > > diff --git > > a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts > > b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts > > new file mode 100644 > > index 000000000000..851091a512dd > > --- /dev/null > > +++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts > > @@ -0,0 +1,1102 @@ > > +// SPDX-License-Identifier: GPL-2.0-or-later // Copyright 2022 > > +Facebook Inc. > > + > > +/dts-v1/; > > +#include "aspeed-g6.dtsi" > > +#include <dt-bindings/gpio/aspeed-gpio.h> #include > > +<dt-bindings/leds/leds-pca955x.h> > > +#include <dt-bindings/i2c/i2c.h> > > + > > +/ { > > + model = "Facebook Yosemite 4 BMC"; > > + compatible = "facebook,yosemite4-bmc", "aspeed,ast2600"; > > + > > + aliases { > > + serial4 = &uart5; > > + serial5 = &uart6; > > + serial6 = &uart7; > > + serial7 = &uart8; > > + serial8 = &uart9; > > + > > + i2c16 = &imux16; > > + i2c17 = &imux17; > > + i2c18 = &imux18; > > + i2c19 = &imux19; > > + i2c20 = &imux20; > > + i2c21 = &imux21; > > + i2c22 = &imux22; > > + i2c23 = &imux23; > > + i2c24 = &imux24; > > + i2c25 = &imux25; > > + i2c26 = &imux26; > > + i2c27 = &imux27; > > + i2c28 = &imux28; > > + i2c29 = &imux29; > > + i2c30 = &imux30; > > + i2c31 = &imux31; > > + i2c32 = &imux32; > > + i2c33 = &imux33; > > + }; > > + > > + chosen { > > + stdout-path = "serial4:57600n8"; > > + }; > > + > > + memory@80000000 { > > + device_type = "memory"; > > + reg = <0x80000000 0x80000000>; > > + }; > > + > > + iio-hwmon { > > + compatible = "iio-hwmon"; > > + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, > <&adc0 3>, > > + <&adc0 4>, <&adc0 5>, <&adc0 6>, > <&adc0 7>, > > + <&adc1 0>, <&adc1 1>; > > + }; > > + > > + spi_gpio: spi-gpio { > > + status = "okay"; > > + compatible = "spi-gpio"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) > GPIO_ACTIVE_HIGH>; > > + gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) > GPIO_ACTIVE_HIGH>; > > + gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) > GPIO_ACTIVE_HIGH>; > > + num-chipselects = <1>; > > + cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) > GPIO_ACTIVE_LOW>; > > + > > + tpmdev@0 { > > + compatible = "tcg,tpm_tis-spi"; > > + spi-max-frequency = <33000000>; > > + reg = <0>; > > + }; > > + }; > > +}; > > + > > +&uart1 { > > + status = "okay"; > > +}; > > + > > +&uart2 { > > + status = "okay"; > > +}; > > + > > +&uart3 { > > + status = "okay"; > > +}; > > + > > +&uart4 { > > + status = "okay"; > > +}; > > + > > +&uart5 { > > + status = "okay"; > > +}; > > + > > +&uart6 { > > + status = "okay"; > > +}; > > + > > +&uart7 { > > + status = "okay"; > > +}; > > + > > +&uart8 { > > + status = "okay"; > > +}; > > + > > +&uart9 { > > + status = "okay"; > > +}; > > + > > +&wdt1 { > > + status = "okay"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_wdtrst1_default>; > > + aspeed,reset-type = "soc"; > > + aspeed,external-signal; > > + aspeed,ext-push-pull; > > + aspeed,ext-active-high; > > + aspeed,ext-pulse-duration = <256>; }; > > + > > +&mac2 { > > + status = "okay"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_rmii3_default>; > > + use-ncsi; > > + mlx,multi-host; > > +}; > > + > > +&mac3 { > > + status = "okay"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_rmii4_default>; > > + use-ncsi; > > + mlx,multi-host; > > +}; > > + > > +&fmc { > > + status = "okay"; > > + flash@0 { > > + status = "okay"; > > + m25p,fast-read; > > + label = "bmc"; > > + spi-rx-bus-width = <4>; > > + spi-max-frequency = <50000000>; #include > > +"openbmc-flash-layout-128.dtsi" > > + }; > > + flash@1 { > > + status = "okay"; > > + m25p,fast-read; > > + label = "bmc2"; > > + spi-rx-bus-width = <4>; > > + spi-max-frequency = <50000000>; > > + }; > > +}; > > + > > +&i2c0 { > > + status = "okay"; > > + mctp-controller; > > + bus-frequency = <400000>; > > + multi-master; > > + > > + mctp@10 { > > + compatible = "mctp-i2c-controller"; > > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > > + }; > > + > > + power-sensor@40 { > > + compatible = "adi,adm1278"; > > + reg = <0x40>; > > + }; > > +}; > > + > > +&i2c1 { > > + status = "okay"; > > + mctp-controller; > > + bus-frequency = <400000>; > > + multi-master; > > + > > + mctp@10 { > > + compatible = "mctp-i2c-controller"; > > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > > + }; > > + > > + power-sensor@40 { > > + compatible = "adi,adm1278"; > > + reg = <0x40>; > > + }; > > +}; > > + > > +&i2c2 { > > + status = "okay"; > > + mctp-controller; > > + bus-frequency = <400000>; > > + multi-master; > > + > > + mctp@10 { > > + compatible = "mctp-i2c-controller"; > > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > > + }; > > + > > + power-sensor@40 { > > + compatible = "adi,adm1278"; > > + reg = <0x40>; > > + }; > > +}; > > + > > +&i2c3 { > > + status = "okay"; > > + mctp-controller; > > + bus-frequency = <400000>; > > + multi-master; > > + > > + mctp@10 { > > + compatible = "mctp-i2c-controller"; > > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > > + }; > > + > > + power-sensor@40 { > > + compatible = "adi,adm1278"; > > + reg = <0x40>; > > + }; > > +}; > > + > > +&i2c4 { > > + status = "okay"; > > + mctp-controller; > > + bus-frequency = <400000>; > > + multi-master; > > + > > + mctp@10 { > > + compatible = "mctp-i2c-controller"; > > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > > + }; > > + > > + power-sensor@40 { > > + compatible = "adi,adm1278"; > > + reg = <0x40>; > > + }; > > +}; > > + > > +&i2c5 { > > + status = "okay"; > > + mctp-controller; > > + bus-frequency = <400000>; > > + multi-master; > > + > > + mctp@10 { > > + compatible = "mctp-i2c-controller"; > > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > > + }; > > + > > + power-sensor@40 { > > + compatible = "adi,adm1278"; > > + reg = <0x40>; > > + }; > > +}; > > + > > +&i2c6 { > > + status = "okay"; > > + mctp-controller; > > + bus-frequency = <400000>; > > + multi-master; > > + > > + mctp@10 { > > + compatible = "mctp-i2c-controller"; > > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > > + }; > > + > > + power-sensor@40 { > > + compatible = "adi,adm1278"; > > + reg = <0x40>; > > + }; > > +}; > > + > > +&i2c7 { > > + status = "okay"; > > + mctp-controller; > > + bus-frequency = <400000>; > > + multi-master; > > + > > + mctp@10 { > > + compatible = "mctp-i2c-controller"; > > + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; > > + }; > > + > > + power-sensor@40 { > > + compatible = "adi,adm1278"; > > + reg = <0x40>; > > + }; > > +}; > > + > > +&i2c8 { > > + status = "okay"; > > + bus-frequency = <400000>; > > + i2c-mux@70 { > > + compatible = "nxp,pca9544"; > > + idle-state = <0>; > > + i2c-mux-idle-disconnect; > > + reg = <0x70>; > > + > > + imux16: i2c@0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0>; > > + gpio@20 { > > + compatible = "nxp,pca9506"; > > + reg = <0x20>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9506"; > > + reg = <0x21>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9506"; > > + reg = <0x22>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9506"; > > + reg = <0x23>; > > + }; > > + > > + gpio@49 { > > + compatible = "nxp,pca9537"; > > + reg = <0x49>; > > + }; > > + > > + eeprom@50 { > > + compatible = "atmel,24c128"; > > + reg = <0x50>; > > + }; > > + > > + eeprom@51 { > > + compatible = "atmel,24c128"; > > + reg = <0x51>; > > + }; > > + > > + eeprom@54 { > > + compatible = "atmel,24c128"; > > + reg = <0x54>; > > + }; > > + }; > > + > > + imux17: i2c@1 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <1>; > > + gpio@20 { > > + compatible = "nxp,pca9506"; > > + reg = <0x20>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9506"; > > + reg = <0x21>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9506"; > > + reg = <0x22>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9506"; > > + reg = <0x23>; > > + }; > > + > > + gpio@49 { > > + compatible = "nxp,pca9537"; > > + reg = <0x49>; > > + }; > > + > > + eeprom@50 { > > + compatible = "atmel,24c128"; > > + reg = <0x50>; > > + }; > > + > > + eeprom@51 { > > + compatible = "atmel,24c128"; > > + reg = <0x51>; > > + }; > > + > > + eeprom@54 { > > + compatible = "atmel,24c128"; > > + reg = <0x54>; > > + }; > > + }; > > + > > + imux18: i2c@2 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <2>; > > + gpio@20 { > > + compatible = "nxp,pca9506"; > > + reg = <0x20>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9506"; > > + reg = <0x21>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9506"; > > + reg = <0x22>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9506"; > > + reg = <0x23>; > > + }; > > + > > + gpio@49 { > > + compatible = "nxp,pca9537"; > > + reg = <0x49>; > > + }; > > + > > + eeprom@50 { > > + compatible = "atmel,24c128"; > > + reg = <0x50>; > > + }; > > + > > + eeprom@51 { > > + compatible = "atmel,24c128"; > > + reg = <0x51>; > > + }; > > + > > + eeprom@54 { > > + compatible = "atmel,24c128"; > > + reg = <0x54>; > > + }; > > + }; > > + > > + imux19: i2c@3 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <3>; > > + gpio@20 { > > + compatible = "nxp,pca9506"; > > + reg = <0x20>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9506"; > > + reg = <0x21>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9506"; > > + reg = <0x22>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9506"; > > + reg = <0x23>; > > + }; > > + > > + gpio@49 { > > + compatible = "nxp,pca9537"; > > + reg = <0x49>; > > + }; > > + > > + eeprom@50 { > > + compatible = "atmel,24c128"; > > + reg = <0x50>; > > + }; > > + > > + eeprom@51 { > > + compatible = "atmel,24c128"; > > + reg = <0x51>; > > + }; > > + > > + eeprom@54 { > > + compatible = "atmel,24c128"; > > + reg = <0x54>; > > + }; > > + }; > > + }; > > +}; > > + > > +&i2c9 { > > + status = "okay"; > > + bus-frequency = <400000>; > > + i2c-mux@71 { > > + compatible = "nxp,pca9544"; > > + idle-state = <0>; > > + i2c-mux-idle-disconnect; > > + reg = <0x71>; > > + > > + imux20: i2c@0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0>; > > + gpio@20 { > > + compatible = "nxp,pca9506"; > > + reg = <0x20>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9506"; > > + reg = <0x21>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9506"; > > + reg = <0x22>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9506"; > > + reg = <0x23>; > > + }; > > + > > + gpio@49 { > > + compatible = "nxp,pca9537"; > > + reg = <0x49>; > > + }; > > + > > + eeprom@50 { > > + compatible = "atmel,24c128"; > > + reg = <0x50>; > > + }; > > + > > + eeprom@51 { > > + compatible = "atmel,24c128"; > > + reg = <0x51>; > > + }; > > + > > + eeprom@54 { > > + compatible = "atmel,24c128"; > > + reg = <0x54>; > > + }; > > + }; > > + > > + imux21: i2c@1 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <1>; > > + gpio@20 { > > + compatible = "nxp,pca9506"; > > + reg = <0x20>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9506"; > > + reg = <0x21>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9506"; > > + reg = <0x22>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9506"; > > + reg = <0x23>; > > + }; > > + > > + gpio@49 { > > + compatible = "nxp,pca9537"; > > + reg = <0x49>; > > + }; > > + > > + eeprom@50 { > > + compatible = "atmel,24c128"; > > + reg = <0x50>; > > + }; > > + > > + eeprom@51 { > > + compatible = "atmel,24c128"; > > + reg = <0x51>; > > + }; > > + > > + eeprom@54 { > > + compatible = "atmel,24c128"; > > + reg = <0x54>; > > + }; > > + }; > > + > > + imux22: i2c@2 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <2>; > > + gpio@20 { > > + compatible = "nxp,pca9506"; > > + reg = <0x20>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9506"; > > + reg = <0x21>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9506"; > > + reg = <0x22>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9506"; > > + reg = <0x23>; > > + }; > > + > > + gpio@49 { > > + compatible = "nxp,pca9537"; > > + reg = <0x49>; > > + }; > > + > > + eeprom@50 { > > + compatible = "atmel,24c128"; > > + reg = <0x50>; > > + }; > > + > > + eeprom@51 { > > + compatible = "atmel,24c128"; > > + reg = <0x51>; > > + }; > > + > > + eeprom@54 { > > + compatible = "atmel,24c128"; > > + reg = <0x54>; > > + }; > > + }; > > + > > + imux23: i2c@3 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <3>; > > + gpio@20 { > > + compatible = "nxp,pca9506"; > > + reg = <0x20>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9506"; > > + reg = <0x21>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9506"; > > + reg = <0x22>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9506"; > > + reg = <0x23>; > > + }; > > + > > + gpio@49 { > > + compatible = "nxp,pca9537"; > > + reg = <0x49>; > > + }; > > + > > + eeprom@50 { > > + compatible = "atmel,24c128"; > > + reg = <0x50>; > > + }; > > + > > + eeprom@51 { > > + compatible = "atmel,24c128"; > > + reg = <0x51>; > > + }; > > + > > + eeprom@54 { > > + compatible = "atmel,24c128"; > > + reg = <0x54>; > > + }; > > + }; > > + }; > > +}; > > + > > +&i2c10 { > > + status = "okay"; > > + bus-frequency = <400000>; > > + i2c-mux@74 { > > + compatible = "nxp,pca9544"; > > + idle-state = <0>; > > + i2c-mux-idle-disconnect; > > + reg = <0x74>; > > + > > + imux28: i2c@0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0>; > > + }; > > + > > + imux29: i2c@1 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <1>; > > + gpio@20 { > > + compatible = "nxp,pca9506"; > > + reg = <0x20>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9506"; > > + reg = <0x21>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9506"; > > + reg = <0x22>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9506"; > > + reg = <0x23>; > > + }; > > + > > + gpio@24 { > > + compatible = "nxp,pca9506"; > > + reg = <0x24>; > > + }; > > + }; > > + }; > > +}; > > + > > +&i2c11 { > > + status = "okay"; > > + power-sensor@10 { > > + compatible = "adi, adm1272"; > > + reg = <0x10>; > > + }; > > + > > + power-sensor@12 { > > + compatible = "adi, adm1272"; > > + reg = <0x12>; > > + }; > > + > > + gpio@20 { > > + compatible = "nxp,pca9555"; > > + reg = <0x20>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9555"; > > + reg = <0x21>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9555"; > > + reg = <0x22>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9555"; > > + reg = <0x23>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + }; > > + > > + temperature-sensor@48 { > > + compatible = "ti,tmp75"; > > + reg = <0x48>; > > + }; > > + > > + temperature-sensor@49 { > > + compatible = "ti,tmp75"; > > + reg = <0x49>; > > + }; > > + > > + eeprom@54 { > > + compatible = "atmel,24c256"; > > + reg = <0x54>; > > + }; > > +}; > > + > > +&i2c12 { > > + status = "okay"; > > + bus-frequency = <400000>; > > + > > + temperature-sensor@48 { > > + compatible = "ti,tmp75"; > > + reg = <0x48>; > > + }; > > + > > + eeprom@50 { > > + compatible = "atmel,24c128"; > > + reg = <0x50>; > > + }; > > + > > + eeprom@54 { > > + compatible = "atmel,24c64"; > > + reg = <0x54>; > > + }; > > + > > + rtc@6f { > > + compatible = "nuvoton,nct3018y"; > > + reg = <0x6f>; > > + }; > > +}; > > + > > +&i2c13 { > > + status = "okay"; > > + bus-frequency = <400000>; > > + gpio@20 { > > + compatible = "nxp,pca9506"; > > + reg = <0x20>; > > + }; > > + > > + gpio@21 { > > + compatible = "nxp,pca9506"; > > + reg = <0x21>; > > + }; > > + > > + gpio@22 { > > + compatible = "nxp,pca9506"; > > + reg = <0x22>; > > + }; > > + > > + gpio@23 { > > + compatible = "nxp,pca9506"; > > + reg = <0x23>; > > + }; > > +}; > > + > > +&i2c14 { > > + status = "okay"; > > + bus-frequency = <400000>; > > + adc@1d { > > + compatible = "ti,adc128d818"; > > + reg = <0x1d>; > > + ti,mode = /bits/ 8 <2>; > > + }; > > + > > + adc@35 { > > + compatible = "ti,adc128d818"; > > + reg = <0x35>; > > + ti,mode = /bits/ 8 <2>; > > + }; > > + > > + adc@37 { > > + compatible = "ti,adc128d818"; > > + reg = <0x37>; > > + ti,mode = /bits/ 8 <2>; > > + }; > > + > > + power-sensor@40 { > > + compatible = "ti,ina233"; > > + reg = <0x40>; > > + }; > > + > > + power-sensor@41 { > > + compatible = "ti,ina233"; > > + reg = <0x41>; > > + }; > > + > > + power-sensor@42 { > > + compatible = "ti,ina233"; > > + reg = <0x42>; > > + }; > > + > > + power-sensor@43 { > > + compatible = "ti,ina233"; > > + reg = <0x43>; > > + }; > > + > > + power-sensor@44 { > > + compatible = "ti,ina233"; > > + reg = <0x44>; > > + }; > > + > > + temperature-sensor@4e { > > + compatible = "ti,tmp75"; > > + reg = <0x4e>; > > + }; > > + > > + temperature-sensor@4f { > > + compatible = "ti,tmp75"; > > + reg = <0x4f>; > > + }; > > + > > + eeprom@51 { > > + compatible = "atmel,24c128"; > > + reg = <0x51>; > > + }; > > + > > + i2c-mux@71 { > > + compatible = "nxp,pca9846"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + idle-state = <0>; > > + i2c-mux-idle-disconnect; > > + reg = <0x71>; > > + > > + imux30: i2c@0 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0>; > > + > > + adc@1f { > > + compatible = "ti,adc128d818"; > > + reg = <0x1f>; > > + ti,mode = /bits/ 8 <2>; > > + }; > > + > > + pwm@20{ > > + compatible = "max31790"; > > This is not documented. It also needs a vendor prefix. The vendor prefix will be added in next time contribution, and this device seems has been used in former projects. Would you please to tell that whether I should inform the driver's author or add the binding document on my own ? > > > + reg = <0x20>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > These 2 are for child nodes, but you don't have any. And a PWM probably > never will. I'll remove the redundant config in next time contribution, thank you for the correction. > > Rob ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2023-09-01 7:55 UTC | newest] Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2023-08-28 6:51 [PATCH v12 0/2] ARM: dts: Facebook Yosemite 4 platform Delphine CC Chiu 2023-08-28 6:51 ` [PATCH v12 1/2] dt-bindings: arm: aspeed: add Facebook Yosemite 4 board Delphine CC Chiu 2023-08-28 6:51 ` [PATCH v12 2/2] ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC Delphine CC Chiu 2023-08-29 14:14 ` Rob Herring 2023-09-01 7:55 ` Delphine_CC_Chiu/WYHQ/Wiwynn
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®