* [PATCH 1/3] arm64: dts: ti: k3-am625: Add boot phase tags marking
2023-09-11 16:25 [PATCH 0/3] arm64: dts: ti: k3-am625: Add boot phase marking Nishanth Menon
@ 2023-09-11 16:25 ` Nishanth Menon
2023-09-11 16:25 ` [PATCH 2/3] arm64: dts: ti: k3-am625-beagleplay: " Nishanth Menon
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Nishanth Menon @ 2023-09-11 16:25 UTC (permalink / raw)
To: Conor Dooley, Krzysztof Kozlowski, Rob Herring, Vignesh
Cc: linux-kernel, devicetree, linux-arm-kernel, Tero Kristo,
Nishanth Menon, Tom Rini, Bryan, Praneeth, Robert Nelson
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to describe various node usage during
boot phases with DT.
On TI K3 AM625 SoC, only secure_proxy_sa3 and esm nodes are
exclusively used by R5 bootloader, rest of the dts nodes with bootph-* are
used by later boot stages also.
Add bootph-all for all other nodes that are used in the bootloader on
K3 AM625 SoC, and bootph-pre-ram is not needed specifically for any
other node in kernel dts.
Signed-off-by: Nishanth Menon <nm@ti.com>
---
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 10 ++++++++++
arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 2 ++
arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi | 2 ++
arch/arm64/boot/dts/ti/k3-am62.dtsi | 3 +++
4 files changed, 17 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index 284b90c94da8..ac760d9b831d 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -81,6 +81,7 @@ audio_refclk1: clock-controller@82e4 {
};
dmss: bus@48000000 {
+ bootph-all;
compatible = "simple-mfd";
#address-cells = <2>;
#size-cells = <2>;
@@ -90,6 +91,7 @@ dmss: bus@48000000 {
ti,sci-dev-id = <25>;
secure_proxy_main: mailbox@4d000000 {
+ bootph-all;
compatible = "ti,am654-secure-proxy";
#mbox-cells = <1>;
reg-names = "target_data", "rt", "scfg";
@@ -165,6 +167,7 @@ main_pktdma: dma-controller@485c0000 {
};
dmsc: system-controller@44043000 {
+ bootph-all;
compatible = "ti,k2g-sci";
ti,host-id = <12>;
mbox-names = "rx", "tx";
@@ -174,16 +177,19 @@ dmsc: system-controller@44043000 {
reg = <0x00 0x44043000 0x00 0xfe0>;
k3_pds: power-controller {
+ bootph-all;
compatible = "ti,sci-pm-domain";
#power-domain-cells = <2>;
};
k3_clks: clock-controller {
+ bootph-all;
compatible = "ti,k2g-sci-clk";
#clock-cells = <2>;
};
k3_reset: reset-controller {
+ bootph-all;
compatible = "ti,sci-reset";
#reset-cells = <2>;
};
@@ -202,6 +208,7 @@ crypto: crypto@40900000 {
};
secure_proxy_sa3: mailbox@43600000 {
+ bootph-pre-ram;
compatible = "ti,am654-secure-proxy";
#mbox-cells = <1>;
reg-names = "target_data", "rt", "scfg";
@@ -217,6 +224,7 @@ secure_proxy_sa3: mailbox@43600000 {
};
main_pmx0: pinctrl@f4000 {
+ bootph-all;
compatible = "pinctrl-single";
reg = <0x00 0xf4000 0x00 0x2ac>;
#pinctrl-cells = <1>;
@@ -225,12 +233,14 @@ main_pmx0: pinctrl@f4000 {
};
main_esm: esm@420000 {
+ bootph-pre-ram;
compatible = "ti,j721e-esm";
reg = <0x00 0x420000 0x00 0x1000>;
ti,esm-pins = <160>, <161>, <162>, <163>, <177>, <178>;
};
main_timer0: timer@2400000 {
+ bootph-all;
compatible = "ti,am654-timer";
reg = <0x00 0x2400000 0x00 0x400>;
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
index 80a3e1db26a9..0e0b234581c6 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
@@ -7,6 +7,7 @@
&cbass_mcu {
mcu_pmx0: pinctrl@4084000 {
+ bootph-all;
compatible = "pinctrl-single";
reg = <0x00 0x04084000 0x00 0x88>;
#pinctrl-cells = <1>;
@@ -15,6 +16,7 @@ mcu_pmx0: pinctrl@4084000 {
};
mcu_esm: esm@4100000 {
+ bootph-pre-ram;
compatible = "ti,j721e-esm";
reg = <0x00 0x4100000 0x00 0x1000>;
ti,esm-pins = <0>, <1>, <2>, <85>;
diff --git a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
index eae052887186..fef76f52a52e 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
@@ -7,6 +7,7 @@
&cbass_wakeup {
wkup_conf: syscon@43000000 {
+ bootph-all;
compatible = "syscon", "simple-mfd";
reg = <0x00 0x43000000 0x00 0x20000>;
#address-cells = <1>;
@@ -14,6 +15,7 @@ wkup_conf: syscon@43000000 {
ranges = <0x0 0x00 0x43000000 0x20000>;
chipid: chipid@14 {
+ bootph-all;
compatible = "ti,am654-chipid";
reg = <0x14 0x4>;
};
diff --git a/arch/arm64/boot/dts/ti/k3-am62.dtsi b/arch/arm64/boot/dts/ti/k3-am62.dtsi
index 11f14eef2d44..f1e15206e1ce 100644
--- a/arch/arm64/boot/dts/ti/k3-am62.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62.dtsi
@@ -47,6 +47,7 @@ pmu: pmu {
};
cbass_main: bus@f0000 {
+ bootph-all;
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
@@ -86,6 +87,7 @@ cbass_main: bus@f0000 {
<0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>;
cbass_mcu: bus@4000000 {
+ bootph-all;
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
@@ -93,6 +95,7 @@ cbass_mcu: bus@4000000 {
};
cbass_wakeup: bus@b00000 {
+ bootph-all;
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
--
2.40.0
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH 2/3] arm64: dts: ti: k3-am625-beagleplay: Add boot phase tags marking
2023-09-11 16:25 [PATCH 0/3] arm64: dts: ti: k3-am625: Add boot phase marking Nishanth Menon
2023-09-11 16:25 ` [PATCH 1/3] arm64: dts: ti: k3-am625: Add boot phase tags marking Nishanth Menon
@ 2023-09-11 16:25 ` Nishanth Menon
2023-09-11 16:25 ` [PATCH 3/3] arm64: dts: ti: k3-am625-sk: " Nishanth Menon
2023-10-03 11:00 ` [PATCH 0/3] arm64: dts: ti: k3-am625: Add boot phase marking Vignesh Raghavendra
3 siblings, 0 replies; 5+ messages in thread
From: Nishanth Menon @ 2023-09-11 16:25 UTC (permalink / raw)
To: Conor Dooley, Krzysztof Kozlowski, Rob Herring, Vignesh
Cc: linux-kernel, devicetree, linux-arm-kernel, Tero Kristo,
Nishanth Menon, Tom Rini, Bryan, Praneeth, Robert Nelson
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to describe various node usage during
boot phases with DT.
Describe the same for beagleplay boot devices.
Signed-off-by: Nishanth Menon <nm@ti.com>
---
.../arm64/boot/dts/ti/k3-am625-beagleplay.dts | 26 +++++++++++++++++++
1 file changed, 26 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
index 7cfdf562b53b..f646d1ec4c05 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-beagleplay.dts
@@ -46,6 +46,7 @@ chosen {
};
memory@80000000 {
+ bootph-pre-ram;
device_type = "memory";
/* 2G RAM */
reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
@@ -83,6 +84,7 @@ wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
};
vsys_5v0: regulator-1 {
+ bootph-all;
compatible = "regulator-fixed";
regulator-name = "vsys_5v0";
regulator-min-microvolt = <5000000>;
@@ -93,6 +95,7 @@ vsys_5v0: regulator-1 {
vdd_3v3: regulator-2 {
/* output of TLV62595DMQR-U12 */
+ bootph-all;
compatible = "regulator-fixed";
regulator-name = "vdd_3v3";
regulator-min-microvolt = <3300000>;
@@ -118,6 +121,7 @@ wlan_en: regulator-3 {
vdd_3v3_sd: regulator-4 {
/* output of TPS22918DBVR-U21 */
+ bootph-all;
pinctrl-names = "default";
pinctrl-0 = <&vdd_3v3_sd_pins_default>;
@@ -132,6 +136,7 @@ vdd_3v3_sd: regulator-4 {
};
vdd_sd_dv: regulator-5 {
+ bootph-all;
compatible = "regulator-gpio";
regulator-name = "sd_hs200_switch";
pinctrl-names = "default";
@@ -146,9 +151,11 @@ vdd_sd_dv: regulator-5 {
};
leds {
+ bootph-all;
compatible = "gpio-leds";
led-0 {
+ bootph-all;
gpios = <&main_gpio0 3 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
function = LED_FUNCTION_HEARTBEAT;
@@ -156,6 +163,7 @@ led-0 {
};
led-1 {
+ bootph-all;
gpios = <&main_gpio0 4 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "disk-activity";
function = LED_FUNCTION_DISK_ACTIVITY;
@@ -163,16 +171,19 @@ led-1 {
};
led-2 {
+ bootph-all;
gpios = <&main_gpio0 5 GPIO_ACTIVE_HIGH>;
function = LED_FUNCTION_CPU;
};
led-3 {
+ bootph-all;
gpios = <&main_gpio0 6 GPIO_ACTIVE_HIGH>;
function = LED_FUNCTION_LAN;
};
led-4 {
+ bootph-all;
gpios = <&main_gpio0 9 GPIO_ACTIVE_HIGH>;
function = LED_FUNCTION_WLAN;
};
@@ -245,6 +256,7 @@ cpsw3g_phy1: ethernet-phy@1 {
&main_pmx0 {
gpio0_pins_default: gpio0-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x0004, PIN_INPUT, 7) /* (G25) OSPI0_LBCLKO.GPIO0_1 */
AM62X_IOPAD(0x0008, PIN_INPUT, 7) /* (J24) OSPI0_DQS.GPIO0_2 */
@@ -264,6 +276,7 @@ AM62X_IOPAD(0x00ac, PIN_INPUT, 7) /* (L21) GPMC0_CSn1.GPIO0_42 */
};
vdd_sd_dv_pins_default: vdd-sd-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x0244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
>;
@@ -283,6 +296,7 @@ AM62X_IOPAD(0x01ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
};
local_i2c_pins_default: local-i2c-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x01e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
AM62X_IOPAD(0x01e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
@@ -321,6 +335,7 @@ AM62X_IOPAD(0x012c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */
};
emmc_pins_default: emmc-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x0220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
AM62X_IOPAD(0x0218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
@@ -336,12 +351,14 @@ AM62X_IOPAD(0x01f8, PIN_INPUT, 0) /* (AC2) MMC0_DAT7 */
};
vdd_3v3_sd_pins_default: vdd-3v3-sd-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x01c4, PIN_INPUT, 7) /* (B14) SPI0_D1_GPIO1_19 */
>;
};
sd_pins_default: sd-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x023c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
AM62X_IOPAD(0x0234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
@@ -418,6 +435,7 @@ AM62X_IOPAD(0x0198, PIN_INPUT, 1) /* (A19) MCASP0_AXR2.SPI2_D1 */
};
mikrobus_gpio_pins_default: mikrobus-gpio-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x019c, PIN_INPUT, 7) /* (B18) MCASP0_AXR1.GPIO1_9 */
AM62X_IOPAD(0x01a0, PIN_INPUT, 7) /* (E18) MCASP0_AXR0.GPIO1_10 */
@@ -426,6 +444,7 @@ AM62X_IOPAD(0x01a8, PIN_INPUT, 7) /* (D20) MCASP0_AFSX.GPIO1_12 */
};
console_pins_default: console-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x01c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
AM62X_IOPAD(0x01cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
@@ -597,6 +616,7 @@ &cpsw3g_mdio {
};
&main_gpio0 {
+ bootph-all;
pinctrl-names = "default";
pinctrl-0 = <&gpio0_pins_default>;
gpio-line-names = "BL_EN_3V3", "SPE_PO_EN", "RTC_INT", /* 0-2 */
@@ -616,6 +636,7 @@ &main_gpio0 {
};
&main_gpio1 {
+ bootph-all;
pinctrl-names = "default";
pinctrl-0 = <&mikrobus_gpio_pins_default>;
gpio-line-names = "", "", "", "", "", /* 0-4 */
@@ -633,6 +654,7 @@ &main_gpio1 {
};
&main_i2c0 {
+ bootph-all;
pinctrl-names = "default";
pinctrl-0 = <&local_i2c_pins_default>;
clock-frequency = <400000>;
@@ -651,6 +673,7 @@ rtc: rtc@68 {
};
tps65219: pmic@30 {
+ bootph-all;
compatible = "ti,tps65219";
reg = <0x30>;
buck1-supply = <&vsys_5v0>;
@@ -801,6 +824,7 @@ &main_spi2 {
};
&sdhci0 {
+ bootph-all;
pinctrl-names = "default";
pinctrl-0 = <&emmc_pins_default>;
ti,driver-strength-ohm = <50>;
@@ -810,6 +834,7 @@ &sdhci0 {
&sdhci1 {
/* SD/MMC */
+ bootph-all;
pinctrl-names = "default";
pinctrl-0 = <&sd_pins_default>;
@@ -850,6 +875,7 @@ wlcore: wlcore@2 {
};
&main_uart0 {
+ bootph-all;
pinctrl-names = "default";
pinctrl-0 = <&console_pins_default>;
status = "okay";
--
2.40.0
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH 3/3] arm64: dts: ti: k3-am625-sk: Add boot phase tags marking
2023-09-11 16:25 [PATCH 0/3] arm64: dts: ti: k3-am625: Add boot phase marking Nishanth Menon
2023-09-11 16:25 ` [PATCH 1/3] arm64: dts: ti: k3-am625: Add boot phase tags marking Nishanth Menon
2023-09-11 16:25 ` [PATCH 2/3] arm64: dts: ti: k3-am625-beagleplay: " Nishanth Menon
@ 2023-09-11 16:25 ` Nishanth Menon
2023-10-03 11:00 ` [PATCH 0/3] arm64: dts: ti: k3-am625: Add boot phase marking Vignesh Raghavendra
3 siblings, 0 replies; 5+ messages in thread
From: Nishanth Menon @ 2023-09-11 16:25 UTC (permalink / raw)
To: Conor Dooley, Krzysztof Kozlowski, Rob Herring, Vignesh
Cc: linux-kernel, devicetree, linux-arm-kernel, Tero Kristo,
Nishanth Menon, Tom Rini, Bryan, Praneeth, Robert Nelson
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to describe various node usage during
boot phases with DT.
Describe the same for am625-sk boot devices.
Signed-off-by: Nishanth Menon <nm@ti.com>
---
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 27 +++++++++++++++++++
.../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 16 +++++++++++
2 files changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 7c98c1b855d1..b18092497c9a 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -31,6 +31,7 @@ memory@80000000 {
vmain_pd: regulator-0 {
/* TPS65988 PD CONTROLLER OUTPUT */
+ bootph-all;
compatible = "regulator-fixed";
regulator-name = "vmain_pd";
regulator-min-microvolt = <5000000>;
@@ -41,6 +42,7 @@ vmain_pd: regulator-0 {
vcc_5v0: regulator-1 {
/* Output of LM34936 */
+ bootph-all;
compatible = "regulator-fixed";
regulator-name = "vcc_5v0";
regulator-min-microvolt = <5000000>;
@@ -52,6 +54,7 @@ vcc_5v0: regulator-1 {
vcc_3v3_sys: regulator-2 {
/* output of LM61460-Q1 */
+ bootph-all;
compatible = "regulator-fixed";
regulator-name = "vcc_3v3_sys";
regulator-min-microvolt = <3300000>;
@@ -63,6 +66,7 @@ vcc_3v3_sys: regulator-2 {
vdd_mmc1: regulator-3 {
/* TPS22918DBVR */
+ bootph-all;
compatible = "regulator-fixed";
regulator-name = "vdd_mmc1";
regulator-min-microvolt = <3300000>;
@@ -75,6 +79,7 @@ vdd_mmc1: regulator-3 {
vdd_sd_dv: regulator-4 {
/* Output of TLV71033 */
+ bootph-all;
compatible = "regulator-gpio";
regulator-name = "tlv71033";
pinctrl-names = "default";
@@ -102,6 +107,7 @@ vcc_1v8: regulator-5 {
&main_pmx0 {
main_rgmii2_pins_default: main-rgmii2-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
@@ -119,6 +125,7 @@ AM62X_IOPAD(0x164, PIN_OUTPUT, 0) /* (AA19) RGMII2_TX_CTL */
};
ospi0_pins_default: ospi0-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
@@ -135,20 +142,32 @@ AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
};
vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (P25) GPMC0_CLK.GPIO0_31 */
>;
};
main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
>;
};
};
+&main_gpio0 {
+ bootph-all;
+};
+
+&main_gpio1 {
+ bootph-all;
+};
+
&main_i2c1 {
+ bootph-all;
exp1: gpio@22 {
+ bootph-all;
compatible = "ti,tca6424";
reg = <0x22>;
gpio-controller;
@@ -207,12 +226,18 @@ mbox_m4_0: mbox-m4-0 {
};
};
+&fss {
+ bootph-all;
+};
+
&ospi0 {
+ bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&ospi0_pins_default>;
flash@0 {
+ bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <8>;
@@ -225,6 +250,7 @@ flash@0 {
cdns,read-delay = <4>;
partitions {
+ bootph-all;
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
@@ -260,6 +286,7 @@ partition@800000 {
};
partition@3fc0000 {
+ bootph-pre-ram;
label = "ospi.phypattern";
reg = <0x3fc0000 0x40000>;
};
diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi b/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
index 677ff8de4b6e..19f57ead4ebd 100644
--- a/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
@@ -28,6 +28,7 @@ chosen {
};
memory@80000000 {
+ bootph-pre-ram;
device_type = "memory";
/* 2G RAM */
reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
@@ -130,6 +131,7 @@ hdmi_connector_in: endpoint {
&main_pmx0 {
/* First pad number is ALW package and second is AMC package */
main_uart0_pins_default: main-uart0-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14/A13) UART0_RXD */
AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14/E11) UART0_TXD */
@@ -137,6 +139,7 @@ AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14/E11) UART0_TXD */
};
main_uart1_pins_default: main-uart1-default-pins {
+ bootph-pre-ram;
pinctrl-single,pins = <
AM62X_IOPAD(0x194, PIN_INPUT, 2) /* (B19/B18) MCASP0_AXR3.UART1_CTSn */
AM62X_IOPAD(0x198, PIN_OUTPUT, 2) /* (A19/B17) MCASP0_AXR2.UART1_RTSn */
@@ -167,6 +170,7 @@ AM62X_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24/H19) GPMC0_CSn3.I2C2_SDA */
};
main_mmc0_pins_default: main-mmc0-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3/V3) MMC0_CMD */
AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1/Y1) MMC0_CLK */
@@ -182,6 +186,7 @@ AM62X_IOPAD(0x1f8, PIN_INPUT, 0) /* (AC2/V4) MMC0_DAT7 */
};
main_mmc1_pins_default: main-mmc1-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x23c, PIN_INPUT, 0) /* (A21/C18) MMC1_CMD */
AM62X_IOPAD(0x234, PIN_INPUT, 0) /* (B22/A20) MMC1_CLK */
@@ -207,6 +212,7 @@ AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22/U16) MDIO0_MDIO */
};
main_rgmii1_pins_default: main-rgmii1-default-pins {
+ bootph-all;
pinctrl-single,pins = <
AM62X_IOPAD(0x14c, PIN_INPUT, 0) /* (AB17/W15) RGMII1_RD0 */
AM62X_IOPAD(0x150, PIN_INPUT, 0) /* (AC17/Y16) RGMII1_RD1 */
@@ -274,6 +280,7 @@ AM62X_IOPAD(0x078, PIN_OUTPUT, 1) /* (U24) GPMC0_AD15.VOUT0_DATA23 */
&mcu_pmx0 {
wkup_uart0_pins_default: wkup-uart0-default-pins {
+ bootph-pre-ram;
pinctrl-single,pins = <
AM62X_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C6/A7) WKUP_UART0_CTSn */
AM62X_MCU_IOPAD(0x030, PIN_OUTPUT, 0) /* (A4/B4) WKUP_UART0_RTSn */
@@ -285,12 +292,14 @@ AM62X_MCU_IOPAD(0x028, PIN_OUTPUT, 0) /* (C5/C6) WKUP_UART0_TXD */
&wkup_uart0 {
/* WKUP UART0 is used by DM firmware */
+ bootph-pre-ram;
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
};
&main_uart0 {
+ bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&main_uart0_pins_default>;
@@ -298,6 +307,7 @@ &main_uart0 {
&main_uart1 {
/* Main UART1 is used by TIFS firmware */
+ bootph-pre-ram;
status = "reserved";
pinctrl-names = "default";
pinctrl-0 = <&main_uart1_pins_default>;
@@ -390,6 +400,7 @@ sii9022_out: endpoint {
};
&sdhci0 {
+ bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&main_mmc0_pins_default>;
@@ -399,6 +410,7 @@ &sdhci0 {
&sdhci1 {
/* SD/MMC */
+ bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&main_mmc1_pins_default>;
@@ -407,21 +419,25 @@ &sdhci1 {
};
&cpsw3g {
+ bootph-all;
pinctrl-names = "default";
pinctrl-0 = <&main_rgmii1_pins_default>;
};
&cpsw_port1 {
+ bootph-all;
phy-mode = "rgmii-rxid";
phy-handle = <&cpsw3g_phy0>;
};
&cpsw3g_mdio {
+ bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&main_mdio1_pins_default>;
cpsw3g_phy0: ethernet-phy@0 {
+ bootph-all;
reg = <0>;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
--
2.40.0
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [PATCH 0/3] arm64: dts: ti: k3-am625: Add boot phase marking
2023-09-11 16:25 [PATCH 0/3] arm64: dts: ti: k3-am625: Add boot phase marking Nishanth Menon
` (2 preceding siblings ...)
2023-09-11 16:25 ` [PATCH 3/3] arm64: dts: ti: k3-am625-sk: " Nishanth Menon
@ 2023-10-03 11:00 ` Vignesh Raghavendra
3 siblings, 0 replies; 5+ messages in thread
From: Vignesh Raghavendra @ 2023-10-03 11:00 UTC (permalink / raw)
To: Conor Dooley, Krzysztof Kozlowski, Rob Herring, Nishanth Menon
Cc: Vignesh Raghavendra, linux-kernel, devicetree, linux-arm-kernel,
Tero Kristo, Tom Rini, Bryan, Praneeth, Robert Nelson
Hi Nishanth Menon,
On Mon, 11 Sep 2023 11:25:32 -0500, Nishanth Menon wrote:
> bootph-all as phase tag was added to dt-schema
> (dtschema/schemas/bootph.yaml) to describe various node usage during
> boot phases with DT.
>
> Based on next-20230911
>
> Nishanth Menon (3):
> arm64: dts: ti: k3-am625: Add boot phase tags marking
> arm64: dts: ti: k3-am625-beagleplay: Add boot phase tags marking
> arm64: dts: ti: k3-am625-sk: Add boot phase tags marking
>
> [...]
I have applied the following to branch ti-k3-dts-next on [1].
Thank you!
[1/3] arm64: dts: ti: k3-am625: Add boot phase tags marking
commit: 87e437a0fb6cbecbabff293061793b32e3bcd3b1
[2/3] arm64: dts: ti: k3-am625-beagleplay: Add boot phase tags marking
commit: 944adefc7f88aec1adf5f76f593d483938bc5e4e
[3/3] arm64: dts: ti: k3-am625-sk: Add boot phase tags marking
commit: c412c2f26eed08b1836ccf79f5547b67c1b55d5d
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh
^ permalink raw reply [flat|nested] 5+ messages in thread