[PATCH 1/2] serial: 8250_mid: Remove 8250_pci usage

[PATCH 1/2] serial: 8250_mid: Remove 8250_pci usage

[Ilpo Järvinen]

8250_mid uses FL_*BASE* from linux/8250_pci.h and nothing else. The
code can be simplified by directly defining BARs within the driver
instead.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
 drivers/tty/serial/8250/8250_mid.c | 18 +++++++-----------
 1 file changed, 7 insertions(+), 11 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_mid.c b/drivers/tty/serial/8250/8250_mid.c
index 2cc78a4bf7a1..8ec03863606e 100644
--- a/drivers/tty/serial/8250/8250_mid.c
+++ b/drivers/tty/serial/8250/8250_mid.c
@@ -12,7 +12,6 @@
 #include <linux/rational.h>
 
 #include <linux/dma/hsu.h>
-#include <linux/8250_pci.h>
 
 #include "8250.h"
 
@@ -32,9 +31,9 @@
 struct mid8250;
 
 struct mid8250_board {
-	unsigned int flags;
 	unsigned long freq;
 	unsigned int base_baud;
+	unsigned int bar;
 	int (*setup)(struct mid8250 *, struct uart_port *p);
 	void (*exit)(struct mid8250 *);
 };
@@ -169,7 +168,6 @@ static int dnv_setup(struct mid8250 *mid, struct uart_port *p)
 {
 	struct hsu_dma_chip *chip = &mid->dma_chip;
 	struct pci_dev *pdev = to_pci_dev(p->dev);
-	unsigned int bar = FL_GET_BASE(mid->board->flags);
 	int ret;
 
 	pci_set_master(pdev);
@@ -183,7 +181,7 @@ static int dnv_setup(struct mid8250 *mid, struct uart_port *p)
 	chip->dev = &pdev->dev;
 	chip->irq = pci_irq_vector(pdev, 0);
 	chip->regs = p->membase;
-	chip->length = pci_resource_len(pdev, bar);
+	chip->length = pci_resource_len(pdev, mid->board->bar);
 	chip->offset = DNV_DMA_CHAN_OFFSET;
 
 	/* Falling back to PIO mode if DMA probing fails */
@@ -291,7 +289,6 @@ static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	struct uart_8250_port uart;
 	struct mid8250 *mid;
-	unsigned int bar;
 	int ret;
 
 	ret = pcim_enable_device(pdev);
@@ -303,7 +300,6 @@ static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 		return -ENOMEM;
 
 	mid->board = (struct mid8250_board *)id->driver_data;
-	bar = FL_GET_BASE(mid->board->flags);
 
 	memset(&uart, 0, sizeof(struct uart_8250_port));
 
@@ -316,8 +312,8 @@ static int mid8250_probe(struct pci_dev *pdev, const struct pci_device_id *id)
 	uart.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT | UPF_FIXED_TYPE;
 	uart.port.set_termios = mid8250_set_termios;
 
-	uart.port.mapbase = pci_resource_start(pdev, bar);
-	uart.port.membase = pcim_iomap(pdev, bar, 0);
+	uart.port.mapbase = pci_resource_start(pdev, mid->board->bar);
+	uart.port.membase = pcim_iomap(pdev, mid->board->bar, 0);
 	if (!uart.port.membase)
 		return -ENOMEM;
 
@@ -353,25 +349,25 @@ static void mid8250_remove(struct pci_dev *pdev)
 }
 
 static const struct mid8250_board pnw_board = {
-	.flags = FL_BASE0,
 	.freq = 50000000,
 	.base_baud = 115200,
+	.bar = 0,
 	.setup = pnw_setup,
 	.exit = pnw_exit,
 };
 
 static const struct mid8250_board tng_board = {
-	.flags = FL_BASE0,
 	.freq = 38400000,
 	.base_baud = 1843200,
+	.bar = 0,
 	.setup = tng_setup,
 	.exit = tng_exit,
 };
 
 static const struct mid8250_board dnv_board = {
-	.flags = FL_BASE1,
 	.freq = 133333333,
 	.base_baud = 115200,
+	.bar = 1,
 	.setup = dnv_setup,
 	.exit = dnv_exit,
 };
-- 
2.30.2

[PATCH 2/2] tty: serial: 8250_exar: Does not use anything from 8250_pci

[Ilpo Järvinen]

8250_exar includes linux/8250_pci.h and depends on SERIAL_8250_PCI.
Neither is necessary so this patch removes the include and changes
the depends on to SERIAL_8250 && PCI (taken from SERIAL_8250_PCI).

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
---
Cc: Matthew Howell <matthew.howell@sealevel.com>

 drivers/tty/serial/8250/8250_exar.c | 1 -
 drivers/tty/serial/8250/Kconfig     | 2 +-
 2 files changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 077c3ba3539e..2f9813429278 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -18,7 +18,6 @@
 #include <linux/slab.h>
 #include <linux/string.h>
 #include <linux/tty.h>
-#include <linux/8250_pci.h>
 #include <linux/delay.h>
 
 #include <asm/byteorder.h>
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index ee17cf5c44c6..d91924cb9b21 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -148,7 +148,7 @@ config SERIAL_8250_PCI
 
 config SERIAL_8250_EXAR
 	tristate "8250/16550 Exar/Commtech PCI/PCIe device support"
-	depends on SERIAL_8250_PCI
+	depends on SERIAL_8250 && PCI
 	default SERIAL_8250
 	help
 	  This builds support for XR17C1xx, XR17V3xx and some Commtech
-- 
2.30.2