* [PATCH v2 0/2] Add Remoteproc Support for TI's J722S SoCs
@ 2024-06-12 11:22 Beleswar Padhi
2024-06-12 11:22 ` [PATCH v2 1/2] arm64: dts: ti: k3-j722s-main: Add R5F and C7x remote processor nodes Beleswar Padhi
2024-06-12 11:22 ` [PATCH v2 2/2] arm64: dts: ti: k3-j722s-evm: Add memory carveouts for R5F and C7x Beleswar Padhi
0 siblings, 2 replies; 3+ messages in thread
From: Beleswar Padhi @ 2024-06-12 11:22 UTC (permalink / raw)
To: nm, vigneshr
Cc: kristo, robh, krzk+dt, conor+dt, j-choudhary, vaishnav.a, afd,
u-kumar1, linux-arm-kernel, devicetree, linux-kernel
Hello All,
The K3 J722S SoCs have one single-core Arm Cortex-R5F processor in each
of the WAKEUP, MCU and MAIN voltage domain, and two C71x DSP subsystems
in MAIN voltage domain. Thus, this series adds the DT Nodes and memory
carveout regions to add remoteproc support in J722S SoCs.
Note: This series is dependent on the following series that introduces
k3-j722s-main.dtsi file:
https://lore.kernel.org/linux-arm-kernel/20240604085252.3686037-4-s-vadapalli@ti.com/
v2: Changelog:
1) Addressed Andrew's comments to refactor remotecore nodes into
k3-j722s-main.dtsi file.
2) Squashed Patch 2 and 3 from V1 into Patch 2 in V2 as they were doing
the same logical thing.
3) The DTBs check warnings from V1 are automatically fixed after a
dt-binding patch[0] was merged in linux-next.
Link to v1:
https://lore.kernel.org/all/20240607090433.488454-1-b-padhi@ti.com/
[0]: https://lore.kernel.org/all/20240604171450.2455-1-hnagalla@ti.com/
Apurva Nandan (2):
arm64: dts: ti: k3-j722s-main: Add R5F and C7x remote processor nodes
arm64: dts: ti: k3-j722s-evm: Add memory carveouts for R5F and C7x
arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 140 ++++++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j722s-main.dtsi | 61 ++++++++++
2 files changed, 201 insertions(+)
--
2.34.1
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH v2 1/2] arm64: dts: ti: k3-j722s-main: Add R5F and C7x remote processor nodes
2024-06-12 11:22 [PATCH v2 0/2] Add Remoteproc Support for TI's J722S SoCs Beleswar Padhi
@ 2024-06-12 11:22 ` Beleswar Padhi
2024-06-12 11:22 ` [PATCH v2 2/2] arm64: dts: ti: k3-j722s-evm: Add memory carveouts for R5F and C7x Beleswar Padhi
1 sibling, 0 replies; 3+ messages in thread
From: Beleswar Padhi @ 2024-06-12 11:22 UTC (permalink / raw)
To: nm, vigneshr
Cc: kristo, robh, krzk+dt, conor+dt, j-choudhary, vaishnav.a, afd,
u-kumar1, linux-arm-kernel, devicetree, linux-kernel
From: Apurva Nandan <a-nandan@ti.com>
The K3 J722S SoCs have one single-core Arm Cortex-R5F processor in each
of the WAKEUP, MCU and MAIN voltage domain, and two C71x DSP subsystems
in MAIN voltage domain. Add the DT nodes to support Inter-Processor
Communication.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
[ refactoring changes to k3-j722s-main.dtsi ]
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
---
arch/arm64/boot/dts/ti/k3-j722s-main.dtsi | 61 +++++++++++++++++++++++
1 file changed, 61 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j722s-main.dtsi b/arch/arm64/boot/dts/ti/k3-j722s-main.dtsi
index b16f3a7cb1097..1ca3f656a7209 100644
--- a/arch/arm64/boot/dts/ti/k3-j722s-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j722s-main.dtsi
@@ -153,6 +153,67 @@ usb1: usb@31200000{
dr_mode = "otg";
};
};
+
+ main_r5fss0: r5fss@78400000 {
+ compatible = "ti,am62-r5fss";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x78400000 0x00 0x78400000 0x8000>,
+ <0x78500000 0x00 0x78500000 0x8000>;
+ power-domains = <&k3_pds 261 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+
+ main_r5fss0_core0: r5f@78400000 {
+ compatible = "ti,am62-r5f";
+ reg = <0x78400000 0x00008000>,
+ <0x78500000 0x00008000>;
+ reg-names = "atcm", "btcm";
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <262>;
+ ti,sci-proc-ids = <0x04 0xff>;
+ resets = <&k3_reset 262 1>;
+ firmware-name = "j722s-main-r5f0_0-fw";
+ ti,atcm-enable = <1>;
+ ti,btcm-enable = <1>;
+ ti,loczrama = <1>;
+ };
+ };
+
+ c7x_0: dsp@7e000000 {
+ compatible = "ti,am62a-c7xv-dsp";
+ reg = <0x00 0x7e000000 0x00 0x00200000>;
+ reg-names = "l2sram";
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <208>;
+ ti,sci-proc-ids = <0x30 0xff>;
+ resets = <&k3_reset 208 1>;
+ firmware-name = "j722s-c71_0-fw";
+ status = "disabled";
+ };
+
+ c7x_1: dsp@7e200000 {
+ compatible = "ti,am62a-c7xv-dsp";
+ reg = <0x00 0x7e200000 0x00 0x00200000>;
+ reg-names = "l2sram";
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <268>;
+ ti,sci-proc-ids = <0x31 0xff>;
+ resets = <&k3_reset 268 1>;
+ firmware-name = "j722s-c71_1-fw";
+ status = "disabled";
+ };
+};
+
+/* MCU domain overrides */
+
+&mcu_r5fss0_core0 {
+ firmware-name = "j722s-mcu-r5f0_0-fw";
+};
+
+/* Wakeup domain overrides */
+
+&wkup_r5fss0_core0 {
+ firmware-name = "j722s-wkup-r5f0_0-fw";
};
&main_conf {
--
2.34.1
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH v2 2/2] arm64: dts: ti: k3-j722s-evm: Add memory carveouts for R5F and C7x
2024-06-12 11:22 [PATCH v2 0/2] Add Remoteproc Support for TI's J722S SoCs Beleswar Padhi
2024-06-12 11:22 ` [PATCH v2 1/2] arm64: dts: ti: k3-j722s-main: Add R5F and C7x remote processor nodes Beleswar Padhi
@ 2024-06-12 11:22 ` Beleswar Padhi
1 sibling, 0 replies; 3+ messages in thread
From: Beleswar Padhi @ 2024-06-12 11:22 UTC (permalink / raw)
To: nm, vigneshr
Cc: kristo, robh, krzk+dt, conor+dt, j-choudhary, vaishnav.a, afd,
u-kumar1, linux-arm-kernel, devicetree, linux-kernel
From: Apurva Nandan <a-nandan@ti.com>
The K3 J722S SoCs have one single-core Arm Cortex-R5F processor in each
of the WAKEUP, MCU and MAIN voltage domain, and two C71x DSP subsystems
in MAIN voltage domain.
The Inter-Processor communication between the main A72 cores and these
R5F and DSP remote cores is achieved through shared memory and
Mailboxes. Thus, add the memory carveouts and enable the mailbox
clusters required for communication.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
[ Added and enabled mailbox instances ]
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
---
arch/arm64/boot/dts/ti/k3-j722s-evm.dts | 140 ++++++++++++++++++++++++
1 file changed, 140 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
index 253b02f0437de..643a017833572 100644
--- a/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j722s-evm.dts
@@ -51,12 +51,71 @@ secure_ddr: optee@9e800000 {
no-map;
};
+ wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa0000000 0x00 0x100000>;
+ no-map;
+ };
+
wkup_r5fss0_core0_memory_region: r5f-memory@a0100000 {
compatible = "shared-dma-pool";
reg = <0x00 0xa0100000 0x00 0xf00000>;
no-map;
};
+ mcu_r5fss0_core0_dma_memory_region: mcu-r5fss-dma-memory-region@a1000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa1000000 0x00 0x100000>;
+ no-map;
+ };
+
+ mcu_r5fss0_core0_memory_region: mcu-r5fss-memory-region@a1100000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa1100000 0x00 0xf00000>;
+ no-map;
+ };
+
+ main_r5fss0_core0_dma_memory_region: main-r5fss-dma-memory-region@a2000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa2000000 0x00 0x100000>;
+ no-map;
+ };
+
+ main_r5fss0_core0_memory_region: main-r5fss-memory-region@a2100000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa2100000 0x00 0xf00000>;
+ no-map;
+ };
+
+ c7x_0_dma_memory_region: c7x-dma-memory@a3000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa3000000 0x00 0x100000>;
+ no-map;
+ };
+
+ c7x_0_memory_region: c7x-memory@a3100000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa3100000 0x00 0xf00000>;
+ no-map;
+ };
+
+ c7x_1_dma_memory_region: c7x-dma-memory@a4000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa4000000 0x00 0x100000>;
+ no-map;
+ };
+
+ c7x_1_memory_region: c7x-memory@a4100000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0xa4100000 0x00 0xf00000>;
+ no-map;
+ };
+
+ rtos_ipc_memory_region: ipc-memories@a5000000 {
+ reg = <0x00 0xa5000000 0x00 0x1c00000>;
+ alignment = <0x1000>;
+ no-map;
+ };
};
vmain_pd: regulator-0 {
@@ -400,6 +459,87 @@ &sdhci1 {
bootph-all;
};
+&mailbox0_cluster0 {
+ status = "okay";
+ mbox_r5_0: mbox-r5-0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
+ };
+};
+
+&mailbox0_cluster1 {
+ status = "okay";
+ mbox_mcu_r5_0: mbox-mcu-r5-0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
+ };
+};
+
+&mailbox0_cluster2 {
+ status = "okay";
+ mbox_c7x_0: mbox-c7x-0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
+ };
+};
+
+&mailbox0_cluster3 {
+ status = "okay";
+ mbox_main_r5_0: mbox-main-r5-0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
+ };
+
+ mbox_c7x_1: mbox-c7x-1 {
+ ti,mbox-rx = <2 0 0>;
+ ti,mbox-tx = <3 0 0>;
+ };
+};
+
+&wkup_r5fss0 {
+ status = "okay";
+};
+
+&wkup_r5fss0_core0 {
+ mboxes = <&mailbox0_cluster0 &mbox_r5_0>;
+ memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
+ <&wkup_r5fss0_core0_memory_region>;
+};
+
+&mcu_r5fss0 {
+ status = "okay";
+};
+
+&mcu_r5fss0_core0 {
+ mboxes = <&mailbox0_cluster1 &mbox_mcu_r5_0>;
+ memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
+ <&mcu_r5fss0_core0_memory_region>;
+};
+
+&main_r5fss0 {
+ status = "okay";
+};
+
+&main_r5fss0_core0 {
+ mboxes = <&mailbox0_cluster3 &mbox_main_r5_0>;
+ memory-region = <&main_r5fss0_core0_dma_memory_region>,
+ <&main_r5fss0_core0_memory_region>;
+};
+
+&c7x_0 {
+ status = "okay";
+ mboxes = <&mailbox0_cluster2 &mbox_c7x_0>;
+ memory-region = <&c7x_0_dma_memory_region>,
+ <&c7x_0_memory_region>;
+};
+
+&c7x_1 {
+ status = "okay";
+ mboxes = <&mailbox0_cluster3 &mbox_c7x_1>;
+ memory-region = <&c7x_1_dma_memory_region>,
+ <&c7x_1_memory_region>;
+};
+
&serdes_ln_ctrl {
idle-states = <J722S_SERDES0_LANE0_USB>,
<J722S_SERDES1_LANE0_PCIE0_LANE0>;
--
2.34.1
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2024-06-12 11:23 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2024-06-12 11:22 [PATCH v2 0/2] Add Remoteproc Support for TI's J722S SoCs Beleswar Padhi
2024-06-12 11:22 ` [PATCH v2 1/2] arm64: dts: ti: k3-j722s-main: Add R5F and C7x remote processor nodes Beleswar Padhi
2024-06-12 11:22 ` [PATCH v2 2/2] arm64: dts: ti: k3-j722s-evm: Add memory carveouts for R5F and C7x Beleswar Padhi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®