[PATCH net-next v2 3/3] net: phy: dp83tg720: Add cable testing support

[Oleksij Rempel <o.rempel@pengutronix.de>]

Introduce cable testing support for the DP83TG720 PHY. This implementation
is based on the "DP83TG720S-Q1: Configuring for Open Alliance Specification
Compliance (Rev. B)" application note.

The feature has been tested with cables of various lengths:
- No cable: 1m till open reported.
- 5 meter cable: reported properly.
- 20 meter cable: reported as 19m.
- 40 meter cable: reported as cable ok.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
changes v2:
- use open alliance specific helpers for the TDR results

 drivers/net/phy/dp83tg720.c | 153 ++++++++++++++++++++++++++++++++++++
 1 file changed, 153 insertions(+)

diff --git a/drivers/net/phy/dp83tg720.c b/drivers/net/phy/dp83tg720.c
index c706429b225a2..06542fce83c95 100644
--- a/drivers/net/phy/dp83tg720.c
+++ b/drivers/net/phy/dp83tg720.c
@@ -3,8 +3,10 @@
  * Copyright (c) 2023 Pengutronix, Oleksij Rempel <kernel@pengutronix.de>
  */
 #include <linux/bitfield.h>
+#include <linux/ethtool_netlink.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/open_alliance_helpers.h>
 #include <linux/phy.h>

 #define DP83TG720S_PHY_ID			0x2000a284
@@ -14,6 +16,17 @@
 #define DP83TG720S_STS_MII_INT			BIT(7)
 #define DP83TG720S_LINK_STATUS			BIT(0)

+/* TDR Configuration Register (0x1E) */
+#define DP83TG720S_TDR_CFG			0x1e
+/* 1b = TDR start, 0b = No TDR */
+#define DP83TG720S_TDR_START			BIT(15)
+/* 1b = TDR auto on link down, 0b = Manual TDR start */
+#define DP83TG720S_CFG_TDR_AUTO_RUN		BIT(14)
+/* 1b = TDR done, 0b = TDR in progress */
+#define DP83TG720S_TDR_DONE			BIT(1)
+/* 1b = TDR fail, 0b = TDR success */
+#define DP83TG720S_TDR_FAIL			BIT(0)
+
 #define DP83TG720S_PHY_RESET			0x1f
 #define DP83TG720S_HW_RESET			BIT(15)

@@ -22,18 +35,155 @@
 /* Power Mode 0 is Normal mode */
 #define DP83TG720S_LPS_CFG3_PWR_MODE_0		BIT(0)

+/* Open Aliance 1000BaseT1 compatible HDD.TDR Fault Status Register */
+#define DP83TG720S_TDR_FAULT_STATUS		0x30f
+
+/* Register 0x0301: TDR Configuration 2 */
+#define DP83TG720S_TDR_CFG2			0x301
+
+/* Register 0x0303: TDR Configuration 3 */
+#define DP83TG720S_TDR_CFG3			0x303
+
+/* Register 0x0304: TDR Configuration 4 */
+#define DP83TG720S_TDR_CFG4			0x304
+
+/* Register 0x0405: Unknown Register */
+#define DP83TG720S_UNKNOWN_0405			0x405
+
+/* Register 0x0576: TDR Master Link Down Control */
+#define DP83TG720S_TDR_MASTER_LINK_DOWN		0x576
+
 #define DP83TG720S_RGMII_DELAY_CTRL		0x602
 /* In RGMII mode, Enable or disable the internal delay for RXD */
 #define DP83TG720S_RGMII_RX_CLK_SEL		BIT(1)
 /* In RGMII mode, Enable or disable the internal delay for TXD */
 #define DP83TG720S_RGMII_TX_CLK_SEL		BIT(0)

+/* Register 0x083F: Unknown Register */
+#define DP83TG720S_UNKNOWN_083F			0x83f
+
 #define DP83TG720S_SQI_REG_1			0x871
 #define DP83TG720S_SQI_OUT_WORST		GENMASK(7, 5)
 #define DP83TG720S_SQI_OUT			GENMASK(3, 1)

 #define DP83TG720_SQI_MAX			7

+/**
+ * dp83tg720_cable_test_start - Start the cable test for the DP83TG720 PHY.
+ * @phydev: Pointer to the phy_device structure.
+ *
+ * This sequence is based on the documented procedure for the DP83TG720 PHY.
+ *
+ * Returns: 0 on success, a negative error code on failure.
+ */
+static int dp83tg720_cable_test_start(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Initialize the PHY to run the TDR test as described in the
+	 * "DP83TG720S-Q1: Configuring for Open Alliance Specification
+	 * Compliance (Rev. B)" application note.
+	 * Most of the registers are not documented. Some of register names
+	 * are guessed by comparing the register offsets with the DP83TD510E.
+	 */
+
+	/* Force master link down */
+	ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2,
+			       DP83TG720S_TDR_MASTER_LINK_DOWN, 0x0400);
+	if (ret)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_TDR_CFG2,
+			    0xa008);
+	if (ret)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_TDR_CFG3,
+			    0x0928);
+	if (ret)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_TDR_CFG4,
+			    0x0004);
+	if (ret)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_UNKNOWN_0405,
+			    0x6400);
+	if (ret)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_UNKNOWN_083F,
+			    0x3003);
+	if (ret)
+		return ret;
+
+	/* Start the TDR */
+	ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_TDR_CFG,
+			       DP83TG720S_TDR_START);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+/**
+ * dp83tg720_cable_test_get_status - Get the status of the cable test for the
+ *                                   DP83TG720 PHY.
+ * @phydev: Pointer to the phy_device structure.
+ * @finished: Pointer to a boolean that indicates whether the test is finished.
+ *
+ * The function sets the @finished flag to true if the test is complete.
+ *
+ * Returns: 0 on success or a negative error code on failure.
+ */
+static int dp83tg720_cable_test_get_status(struct phy_device *phydev,
+					   bool *finished)
+{
+	int ret, stat;
+
+	*finished = false;
+
+	/* Read the TDR status */
+	ret = phy_read_mmd(phydev, MDIO_MMD_VEND2, DP83TG720S_TDR_CFG);
+	if (ret < 0)
+		return ret;
+
+	/* Check if the TDR test is done */
+	if (!(ret & DP83TG720S_TDR_DONE))
+		return 0;
+
+	/* Check for TDR test failure */
+	if (!(ret & DP83TG720S_TDR_FAIL)) {
+		int location;
+
+		/* Read fault status */
+		ret = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+				   DP83TG720S_TDR_FAULT_STATUS);
+		if (ret < 0)
+			return ret;
+
+		/* Get fault type */
+		stat = oa_1000bt1_get_ethtool_cable_result_code(ret);
+
+		/* Determine fault location */
+		location = oa_1000bt1_get_tdr_distance(ret);
+		if (location > 0)
+			ethnl_cable_test_fault_length(phydev,
+						      ETHTOOL_A_CABLE_PAIR_A,
+						      location);
+	} else {
+		/* Active link partner or other issues */
+		stat = ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+	}
+
+	*finished = true;
+
+	ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A, stat);
+
+	return phy_init_hw(phydev);
+}
+
 static int dp83tg720_config_aneg(struct phy_device *phydev)
 {
 	int ret;
@@ -195,12 +345,15 @@ static struct phy_driver dp83tg720_driver[] = {
 	PHY_ID_MATCH_MODEL(DP83TG720S_PHY_ID),
 	.name		= "TI DP83TG720S",

+	.flags          = PHY_POLL_CABLE_TEST,
 	.config_aneg	= dp83tg720_config_aneg,
 	.read_status	= dp83tg720_read_status,
 	.get_features	= genphy_c45_pma_read_ext_abilities,
 	.config_init	= dp83tg720_config_init,
 	.get_sqi	= dp83tg720_get_sqi,
 	.get_sqi_max	= dp83tg720_get_sqi_max,
+	.cable_test_start = dp83tg720_cable_test_start,
+	.cable_test_get_status = dp83tg720_cable_test_get_status,

 	.suspend	= genphy_suspend,
 	.resume		= genphy_resume,
--
2.39.2