[PATCH 2/2] arm64: dts: qcom: x1e80100-romulus: Set up USB Multiport controller

[Konrad Dybcio <konradybcio@kernel.org>]

From: Konrad Dybcio <quic_kdybcio@quicinc.com>

The USB MP controller is wired up to the USB-A port on the left side
and to the Surface Connector on the right side. Configure it.

While at it, remove a stray double \n.

Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
---
 .../boot/dts/qcom/x1e80100-microsoft-romulus.dtsi  | 59 +++++++++++++++++++++-
 1 file changed, 57 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi b/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
index 5419d0b02785..ac2acf949b70 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
@@ -572,7 +572,17 @@ &i2c5 {
 
 	status = "okay";
 
-	/* Something @4f */
+	ptn3222: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+
+		reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+		vdd3v3-supply = <&vreg_l13b>;
+		vdd1v8-supply = <&vreg_l4b>;
+
+		#phy-cells = <0>;
+	};
 };
 
 &i2c7 {
@@ -583,7 +593,6 @@ &i2c7 {
 	/* PS8830 USB retimer @8 */
 };
 
-
 &mdss {
 	status = "okay";
 };
@@ -717,6 +726,15 @@ &smb2360_1_eusb2_repeater {
 	vdd3-supply = <&vreg_l14b>;
 };
 
+&smb2360_2 {
+	status = "okay";
+};
+
+&smb2360_2_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d>;
+	vdd3-supply = <&vreg_l8b>;
+};
+
 &tlmm {
 	gpio-reserved-ranges = <44 4>, /* SPI (TPM) */
 			       <238 1>; /* UFS Reset */
@@ -856,3 +874,40 @@ &usb_1_ss1_dwc3_hs {
 &usb_1_ss1_qmpphy_out {
 	remote-endpoint = <&pmic_glink_ss1_ss_in>;
 };
+
+/* MP0 goes to the Surface Connector, MP1 goes to the USB-A port */
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e>;
+	vdda12-supply = <&vreg_l2j>;
+
+	phys = <&smb2360_2_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_hsphy1 {
+	vdd-supply = <&vreg_l2e>;
+	vdda12-supply = <&vreg_l2j>;
+
+	phys = <&ptn3222>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3e>;
+	vdda-pll-supply = <&vreg_l3c>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3e>;
+	vdda-pll-supply = <&vreg_l3c>;
+
+	status = "okay";
+};

-- 
2.46.0