Re: [PATCH 2/2] arm64: dts: qcom: x1e80100-romulus: Set up USB Multiport controller

[neil.armstrong@linaro.org]

On 02/09/2024 16:50, Konrad Dybcio wrote:
> From: Konrad Dybcio <quic_kdybcio@quicinc.com>
> 
> The USB MP controller is wired up to the USB-A port on the left side
> and to the Surface Connector on the right side. Configure it.
> 
> While at it, remove a stray double \n.
> 
> Signed-off-by: Konrad Dybcio <quic_kdybcio@quicinc.com>
> ---
>   .../boot/dts/qcom/x1e80100-microsoft-romulus.dtsi  | 59 +++++++++++++++++++++-
>   1 file changed, 57 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi b/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
> index 5419d0b02785..ac2acf949b70 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
> @@ -572,7 +572,17 @@ &i2c5 {
>   
>   	status = "okay";
>   
> -	/* Something @4f */
> +	ptn3222: redriver@4f {
> +		compatible = "nxp,ptn3222";
> +		reg = <0x4f>;
> +
> +		reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
> +
> +		vdd3v3-supply = <&vreg_l13b>;
> +		vdd1v8-supply = <&vreg_l4b>;
> +
> +		#phy-cells = <0>;

It's unrelated to mutiport USB-A, should go in a separate change,
and also probably in a bigger change enabling usb-c features using
the retimer.

Neil

> +	};
>   };
>   
>   &i2c7 {
> @@ -583,7 +593,6 @@ &i2c7 {
>   	/* PS8830 USB retimer @8 */
>   };
>   
> -
>   &mdss {
>   	status = "okay";
>   };
> @@ -717,6 +726,15 @@ &smb2360_1_eusb2_repeater {
>   	vdd3-supply = <&vreg_l14b>;
>   };
>   
> +&smb2360_2 {
> +	status = "okay";
> +};
> +
> +&smb2360_2_eusb2_repeater {
> +	vdd18-supply = <&vreg_l3d>;
> +	vdd3-supply = <&vreg_l8b>;
> +};
> +
>   &tlmm {
>   	gpio-reserved-ranges = <44 4>, /* SPI (TPM) */
>   			       <238 1>; /* UFS Reset */
> @@ -856,3 +874,40 @@ &usb_1_ss1_dwc3_hs {
>   &usb_1_ss1_qmpphy_out {
>   	remote-endpoint = <&pmic_glink_ss1_ss_in>;
>   };
> +
> +/* MP0 goes to the Surface Connector, MP1 goes to the USB-A port */
> +&usb_mp {
> +	status = "okay";
> +};
> +
> +&usb_mp_hsphy0 {
> +	vdd-supply = <&vreg_l2e>;
> +	vdda12-supply = <&vreg_l2j>;
> +
> +	phys = <&smb2360_2_eusb2_repeater>;
> +
> +	status = "okay";
> +};
> +
> +&usb_mp_hsphy1 {
> +	vdd-supply = <&vreg_l2e>;
> +	vdda12-supply = <&vreg_l2j>;
> +
> +	phys = <&ptn3222>;
> +
> +	status = "okay";
> +};
> +
> +&usb_mp_qmpphy0 {
> +	vdda-phy-supply = <&vreg_l3e>;
> +	vdda-pll-supply = <&vreg_l3c>;
> +
> +	status = "okay";
> +};
> +
> +&usb_mp_qmpphy1 {
> +	vdda-phy-supply = <&vreg_l3e>;
> +	vdda-pll-supply = <&vreg_l3c>;
> +
> +	status = "okay";
> +};
>