[PATCH v4 1/2] dt-bindings: serial: sc16is7xx: Add description for polling mode

[PATCH v4 1/2] dt-bindings: serial: sc16is7xx: Add description for polling mode

[Andre Werner]

Polling mode is enabled if the "interrupts" property is missing.
Thus, this commit deletes "interrupts" entry from "required" section
and adds a description for the fallback to polling mode at the
"interrupts" entry.

Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
V3:
- No changes on source.
- Add Acked-By to commit message.
V4:
- No changes
---
 Documentation/devicetree/bindings/serial/nxp,sc16is7xx.yaml | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.yaml b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.yaml
index 88871480018e..ab39b95dae40 100644
--- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.yaml
+++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.yaml
@@ -23,6 +23,8 @@ properties:
     maxItems: 1
 
   interrupts:
+    description:
+      When missing, device driver uses polling instead.
     maxItems: 1
 
   clocks:
@@ -76,7 +78,6 @@ properties:
 required:
   - compatible
   - reg
-  - interrupts
 
 allOf:
   - $ref: /schemas/spi/spi-peripheral-props.yaml#
-- 
2.47.1

[PATCH v4 2/2] serial: sc16is7xx: Add polling mode if no IRQ pin is available

[Andre Werner]

Fall back to polling mode if no interrupt is configured because there
is no possibility to connect the interrupt pin.
If "interrupts" property is missing in devicetree the driver
uses a delayed worker to pull the state of interrupt status registers.

Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
---
V2:
- Change warning for polling mode to debug log entry
- Correct typo: Resuse -> Reuse
- Format define with missing tabs for SC16IS7XX_POLL_PERIOD
- Format struct declaration sc16is7xx_one_config with missing tabs for polling and shutdown
- Adapt dtbinding with new polling feature
V3:
- Use suffix with units and drop a comment SC16IS7XX_POLL_PERIOD_MS. Sorry for that miss.
- Make Kernel lowercase.
V4:
- Reword commit messages for better understanding.
- Remove 'shutdown' property for canceling delayed worker.
- Rename worker function: sc16is7xx_transmission_poll -> sc16is7xx_poll_proc
- Unify argument for worker functions: kthread_work *work -> kthread_work *ws
---
 drivers/tty/serial/sc16is7xx.c | 38 ++++++++++++++++++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index a3093e09309f..6645cab2ae5f 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -314,6 +314,7 @@
 #define SC16IS7XX_FIFO_SIZE		(64)
 #define SC16IS7XX_GPIOS_PER_BANK	4
 
+#define SC16IS7XX_POLL_PERIOD_MS	10
 #define SC16IS7XX_RECONF_MD		BIT(0)
 #define SC16IS7XX_RECONF_IER		BIT(1)
 #define SC16IS7XX_RECONF_RS485		BIT(2)
@@ -348,6 +349,8 @@ struct sc16is7xx_port {
 	u8				mctrl_mask;
 	struct kthread_worker		kworker;
 	struct task_struct		*kworker_task;
+	struct kthread_delayed_work	poll_work;
+	bool				polling;
 	struct sc16is7xx_one		p[];
 };
 
@@ -861,6 +864,18 @@ static irqreturn_t sc16is7xx_irq(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+static void sc16is7xx_poll_proc(struct kthread_work *ws)
+{
+	struct sc16is7xx_port *s = container_of(ws, struct sc16is7xx_port, poll_work.work);
+
+	/* Reuse standard IRQ handler. Interrupt ID is unused in this context. */
+	sc16is7xx_irq(0, s);
+
+	/* Setup delay based on SC16IS7XX_POLL_PERIOD_MS */
+	kthread_queue_delayed_work(&s->kworker, &s->poll_work,
+				   msecs_to_jiffies(SC16IS7XX_POLL_PERIOD_MS));
+}
+
 static void sc16is7xx_tx_proc(struct kthread_work *ws)
 {
 	struct uart_port *port = &(to_sc16is7xx_one(ws, tx_work)->port);
@@ -1149,6 +1164,7 @@ static int sc16is7xx_config_rs485(struct uart_port *port, struct ktermios *termi
 static int sc16is7xx_startup(struct uart_port *port)
 {
 	struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
+	struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
 	unsigned int val;
 	unsigned long flags;
 
@@ -1211,6 +1227,10 @@ static int sc16is7xx_startup(struct uart_port *port)
 	sc16is7xx_enable_ms(port);
 	uart_port_unlock_irqrestore(port, flags);
 
+	if (s->polling)
+		kthread_queue_delayed_work(&s->kworker, &s->poll_work,
+					   msecs_to_jiffies(SC16IS7XX_POLL_PERIOD_MS));
+
 	return 0;
 }
 
@@ -1232,6 +1252,9 @@ static void sc16is7xx_shutdown(struct uart_port *port)
 
 	sc16is7xx_power(port, 0);
 
+	if (s->polling)
+		kthread_cancel_delayed_work_sync(&s->poll_work);
+
 	kthread_flush_worker(&s->kworker);
 }
 
@@ -1537,6 +1560,12 @@ int sc16is7xx_probe(struct device *dev, const struct sc16is7xx_devtype *devtype,
 
 	/* Always ask for fixed clock rate from a property. */
 	device_property_read_u32(dev, "clock-frequency", &uartclk);
+	s->polling = !device_property_present(dev, "interrupts");
+	if (s->polling) {
+		dev_dbg(dev,
+			"No interrupt pin definition, falling back to polling mode\n");
+		irq = 0;
+	}
 
 	s->clk = devm_clk_get_optional(dev, NULL);
 	if (IS_ERR(s->clk))
@@ -1665,6 +1694,12 @@ int sc16is7xx_probe(struct device *dev, const struct sc16is7xx_devtype *devtype,
 		goto out_ports;
 #endif
 
+	if (s->polling) {
+		/* Initialize kernel thread for polling */
+		kthread_init_delayed_work(&s->poll_work, sc16is7xx_poll_proc);
+		return 0;
+	}
+
 	/*
 	 * Setup interrupt. We first try to acquire the IRQ line as level IRQ.
 	 * If that succeeds, we can allow sharing the interrupt as well.
@@ -1724,6 +1759,9 @@ void sc16is7xx_remove(struct device *dev)
 		sc16is7xx_power(&s->p[i].port, 0);
 	}
 
+	if (s->polling)
+		kthread_cancel_delayed_work_sync(&s->poll_work);
+
 	kthread_flush_worker(&s->kworker);
 	kthread_stop(s->kworker_task);
 
-- 
2.47.1

Re: [PATCH v4 2/2] serial: sc16is7xx: Add polling mode if no IRQ pin is available

[Hugo Villeneuve]

Hi Andre,

On Thu,  9 Jan 2025 10:38:34 +0100
Andre Werner <andre.werner@systec-electronic.com> wrote:

> Fall back to polling mode if no interrupt is configured because there
> is no possibility to connect the interrupt pin.
> If "interrupts" property is missing in devicetree the driver
> uses a delayed worker to pull the state of interrupt status registers.
> 
> Signed-off-by: Andre Werner <andre.werner@systec-electronic.com>
> ---
> V2:
> - Change warning for polling mode to debug log entry
> - Correct typo: Resuse -> Reuse
> - Format define with missing tabs for SC16IS7XX_POLL_PERIOD
> - Format struct declaration sc16is7xx_one_config with missing tabs for polling and shutdown
> - Adapt dtbinding with new polling feature
> V3:
> - Use suffix with units and drop a comment SC16IS7XX_POLL_PERIOD_MS. Sorry for that miss.
> - Make Kernel lowercase.
> V4:
> - Reword commit messages for better understanding.
> - Remove 'shutdown' property for canceling delayed worker.
> - Rename worker function: sc16is7xx_transmission_poll -> sc16is7xx_poll_proc
> - Unify argument for worker functions: kthread_work *work -> kthread_work *ws
> ---
>  drivers/tty/serial/sc16is7xx.c | 38 ++++++++++++++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
> 
> diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
> index a3093e09309f..6645cab2ae5f 100644
> --- a/drivers/tty/serial/sc16is7xx.c
> +++ b/drivers/tty/serial/sc16is7xx.c
> @@ -314,6 +314,7 @@
>  #define SC16IS7XX_FIFO_SIZE		(64)
>  #define SC16IS7XX_GPIOS_PER_BANK	4
>  
> +#define SC16IS7XX_POLL_PERIOD_MS	10
>  #define SC16IS7XX_RECONF_MD		BIT(0)
>  #define SC16IS7XX_RECONF_IER		BIT(1)
>  #define SC16IS7XX_RECONF_RS485		BIT(2)
> @@ -348,6 +349,8 @@ struct sc16is7xx_port {
>  	u8				mctrl_mask;
>  	struct kthread_worker		kworker;
>  	struct task_struct		*kworker_task;
> +	struct kthread_delayed_work	poll_work;
> +	bool				polling;
>  	struct sc16is7xx_one		p[];
>  };
>  
> @@ -861,6 +864,18 @@ static irqreturn_t sc16is7xx_irq(int irq, void *dev_id)
>  	return IRQ_HANDLED;
>  }
>  
> +static void sc16is7xx_poll_proc(struct kthread_work *ws)
> +{
> +	struct sc16is7xx_port *s = container_of(ws, struct sc16is7xx_port, poll_work.work);
> +
> +	/* Reuse standard IRQ handler. Interrupt ID is unused in this context. */
> +	sc16is7xx_irq(0, s);
> +
> +	/* Setup delay based on SC16IS7XX_POLL_PERIOD_MS */
> +	kthread_queue_delayed_work(&s->kworker, &s->poll_work,
> +				   msecs_to_jiffies(SC16IS7XX_POLL_PERIOD_MS));
> +}
> +
>  static void sc16is7xx_tx_proc(struct kthread_work *ws)
>  {
>  	struct uart_port *port = &(to_sc16is7xx_one(ws, tx_work)->port);
> @@ -1149,6 +1164,7 @@ static int sc16is7xx_config_rs485(struct uart_port *port, struct ktermios *termi
>  static int sc16is7xx_startup(struct uart_port *port)
>  {
>  	struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
> +	struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
>  	unsigned int val;
>  	unsigned long flags;
>  
> @@ -1211,6 +1227,10 @@ static int sc16is7xx_startup(struct uart_port *port)
>  	sc16is7xx_enable_ms(port);
>  	uart_port_unlock_irqrestore(port, flags);
>  
> +	if (s->polling)
> +		kthread_queue_delayed_work(&s->kworker, &s->poll_work,
> +					   msecs_to_jiffies(SC16IS7XX_POLL_PERIOD_MS));
> +
>  	return 0;
>  }
>  
> @@ -1232,6 +1252,9 @@ static void sc16is7xx_shutdown(struct uart_port *port)
>  
>  	sc16is7xx_power(port, 0);
>  
> +	if (s->polling)
> +		kthread_cancel_delayed_work_sync(&s->poll_work);
> +
>  	kthread_flush_worker(&s->kworker);
>  }
>  
> @@ -1537,6 +1560,12 @@ int sc16is7xx_probe(struct device *dev, const struct sc16is7xx_devtype *devtype,
>  
>  	/* Always ask for fixed clock rate from a property. */
>  	device_property_read_u32(dev, "clock-frequency", &uartclk);

You are still missing a blank line here to better separate logical
blocks (polling is not related to clock-frequency).

> +	s->polling = !device_property_present(dev, "interrupts");
> +	if (s->polling) {
> +		dev_dbg(dev,
> +			"No interrupt pin definition, falling back to polling mode\n");
> +		irq = 0;
> +	}
>  
>  	s->clk = devm_clk_get_optional(dev, NULL);
>  	if (IS_ERR(s->clk))
> @@ -1665,6 +1694,12 @@ int sc16is7xx_probe(struct device *dev, const struct sc16is7xx_devtype *devtype,
>  		goto out_ports;
>  #endif
>  
> +	if (s->polling) {
> +		/* Initialize kernel thread for polling */
> +		kthread_init_delayed_work(&s->poll_work, sc16is7xx_poll_proc);
> +		return 0;
> +	}
> +
>  	/*
>  	 * Setup interrupt. We first try to acquire the IRQ line as level IRQ.
>  	 * If that succeeds, we can allow sharing the interrupt as well.
> @@ -1724,6 +1759,9 @@ void sc16is7xx_remove(struct device *dev)
>  		sc16is7xx_power(&s->p[i].port, 0);
>  	}
>  
> +	if (s->polling)
> +		kthread_cancel_delayed_work_sync(&s->poll_work);
> +
>  	kthread_flush_worker(&s->kworker);
>  	kthread_stop(s->kworker_task);
>  
> -- 
> 2.47.1
> 
> 
> 


-- 
Hugo Villeneuve