mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Mathis Foerst <mathis.foerst@mt.com>
To: linux-kernel@vger.kernel.org
Cc: Mathis Foerst <mathis.foerst@mt.com>,
	Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
	Mauro Carvalho Chehab <mchehab@kernel.org>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Sakari Ailus <sakari.ailus@linux.intel.com>,
	linux-media@vger.kernel.org, devicetree@vger.kernel.org,
	manuel.traut@mt.com, mathis.foerst@zuehlke.com
Subject: [PATCH v4 0/6] MT9M114 driver bugfix and improvements
Date: Fri,  7 Mar 2025 10:31:34 +0100	[thread overview]
Message-ID: <20250307093140.370061-1-mathis.foerst@mt.com> (raw)

Hi,

this patch series contains the following bugfix and improvements
for the MT9M114 camera driver:

Changelog:

v3 -> v4:
- Rename DT binding from "onnn,slew-rate" to "slew-rate" in PATCH 1 and 6 as
  requested in the review comment.

v2 -> v3:
- Dropped PATCH 2 ("media: mt9m114: Add get_mbus_config").
  Based on the comments, this issure won't be fixed in the MT9M114
  driver but in "imx-media-csi.c" in a separate patch.
- Renumbered patches accordingly.
- Fix the incomplete renaming of the DT property from 'pad-slew-rate'
  to 'onnn,slew-rate' in PATCH 1 and 6.
- Fix checkpatch formatting suggestions in PATCH 2 and 6.

v1 -> v2:
- Fix the subjects of the patches
- Dropped PATCH 1 ("Add bypass-pll DT-binding") as it can be automatically
  detected if the PLL should be bypassed.
- Renumbered patches accordingly
- Switch to uint32, add default value and clarify documentation in PATCH 1
- Add 'Fixes' and 'Cc' tags as suggested in PATCH 6

Link to v1 discussion:
https://lore.kernel.org/linux-media/20250226153929.274562-1-mathis.foerst@mt.com/
Link to v2 discussion:
https://lore.kernel.org/linux-media/20250304103647.34235-1-mathis.foerst@mt.com/
Link to v3 discussion:
https://lore.kernel.org/linux-media/20250305101453.708270-1-mathis.foerst@mt.com/


Bugfixes:
- Fix a deadlock when using the V4L2 pad-ops get/set_frame_interval

New Features:
- Bypass the internal PLL if EXTCLK matches the configured link_frequency
- Make the slew-rate of the output pads configurable via DT
- Allow to change the cropping configuration and the horizontal/vertical
  flipping while the sensor is in streaming state

Thanks,
Mathis


Mathis Foerst (6):
  media: dt-bindings: mt9m114: Add slew-rate DT-binding
  media: mt9m114: Bypass PLL if required
  media: mt9m114: Factor out mt9m114_configure_pa
  media: mt9m114: Allow set_selection while streaming
  media: mt9m114: Fix deadlock in get_frame_interval/set_frame_interval
  media: mt9m114: Set pad-slew-rate

 .../bindings/media/i2c/onnn,mt9m114.yaml      |   9 +
 drivers/media/i2c/mt9m114.c                   | 172 ++++++++++++------
 2 files changed, 130 insertions(+), 51 deletions(-)


base-commit: ac9c34d1e45a4c25174ced4fc0cfc33ff3ed08c7
-- 
2.34.1


             reply	other threads:[~2025-03-07  9:32 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-03-07  9:31 Mathis Foerst [this message]
2025-03-07  9:31 ` [PATCH v4 1/6] media: dt-bindings: mt9m114: Add slew-rate DT-binding Mathis Foerst
2025-03-10  9:36   ` Krzysztof Kozlowski
2025-04-23 18:01   ` Laurent Pinchart
2025-03-07  9:31 ` [PATCH v4 2/6] media: mt9m114: Bypass PLL if required Mathis Foerst
2025-04-23 18:09   ` Laurent Pinchart
2025-03-07  9:31 ` [PATCH v4 3/6] media: mt9m114: Factor out mt9m114_configure_pa Mathis Foerst
2025-04-23 18:14   ` Laurent Pinchart
2025-03-07  9:31 ` [PATCH v4 4/6] media: mt9m114: Allow set_selection while streaming Mathis Foerst
2025-04-23 18:39   ` Laurent Pinchart
2025-05-22 14:21     ` Mathis Foerst
2025-03-07  9:31 ` [PATCH v4 5/6] media: mt9m114: Fix deadlock in get_frame_interval/set_frame_interval Mathis Foerst
2025-04-23 18:16   ` Laurent Pinchart
2025-03-07  9:31 ` [PATCH v4 6/6] media: mt9m114: Set pad-slew-rate Mathis Foerst
2025-04-23 18:23   ` Laurent Pinchart

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20250307093140.370061-1-mathis.foerst@mt.com \
    --to=mathis.foerst@mt.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=laurent.pinchart@ideasonboard.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=manuel.traut@mt.com \
    --cc=mathis.foerst@zuehlke.com \
    --cc=mchehab@kernel.org \
    --cc=robh@kernel.org \
    --cc=sakari.ailus@linux.intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®