From: Daniel Schultz <d.schultz@phytec.de>
To: <nm@ti.com>, <vigneshr@ti.com>, <kristo@kernel.org>,
<robh@kernel.org>, <krzk+dt@kernel.org>, <conor+dt@kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Cc: <upstream@lists.phytec.de>, Daniel Schultz <d.schultz@phytec.de>
Subject: [PATCH v2 1/2] arm64: dts: ti: k3-am62a: Enable CPU freq throttling on thermal alert
Date: Tue, 6 May 2025 04:41:33 -0700 [thread overview]
Message-ID: <20250506114134.3514899-1-d.schultz@phytec.de> (raw)
Enable throttling down the CPU frequency when an alert temperature
threshold (lower than the critical threshold) is reached.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
---
Changes in v2:
* Increased passive trip point to 115C (10C below crit)
* Dropped patch which decreased critical trip point.
arch/arm64/boot/dts/ti/k3-am62a-thermal.dtsi | 57 ++++++++++++++++++--
arch/arm64/boot/dts/ti/k3-am62a7.dtsi | 4 ++
2 files changed, 58 insertions(+), 3 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am62a-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-thermal.dtsi
index c7486fb2a5b4..3aa127157d24 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-thermal.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-thermal.dtsi
@@ -12,12 +12,29 @@ main0_thermal: main0-thermal {
thermal-sensors = <&wkup_vtm0 0>;
trips {
+ main0_alert: main0-alert {
+ temperature = <115000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
main0_crit: main0-crit {
temperature = <125000>; /* milliCelsius */
hysteresis = <2000>; /* milliCelsius */
type = "critical";
};
};
+
+ cooling-maps {
+ map0 {
+ trip = <&main0_alert>;
+ cooling-device =
+ <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
};
main1_thermal: main1-thermal {
@@ -26,25 +43,59 @@ main1_thermal: main1-thermal {
thermal-sensors = <&wkup_vtm0 1>;
trips {
+ main1_alert: main1-alert {
+ temperature = <115000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
main1_crit: main1-crit {
temperature = <125000>; /* milliCelsius */
hysteresis = <2000>; /* milliCelsius */
type = "critical";
};
};
+
+ cooling-maps {
+ map0 {
+ trip = <&main1_alert>;
+ cooling-device =
+ <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
};
main2_thermal: main2-thermal {
- polling-delay-passive = <250>; /* milliSeconds */
- polling-delay = <500>; /* milliSeconds */
- thermal-sensors = <&wkup_vtm0 2>;
+ polling-delay-passive = <250>; /* milliSeconds */
+ polling-delay = <500>; /* milliSeconds */
+ thermal-sensors = <&wkup_vtm0 2>;
trips {
+ main2_alert: main2-alert {
+ temperature = <115000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
main2_crit: main2-crit {
temperature = <125000>; /* milliCelsius */
hysteresis = <2000>; /* milliCelsius */
type = "critical";
};
};
+
+ cooling-maps {
+ map0 {
+ trip = <&main2_alert>;
+ cooling-device =
+ <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-am62a7.dtsi b/arch/arm64/boot/dts/ti/k3-am62a7.dtsi
index 6c99221beb6b..b6e5eee99370 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a7.dtsi
@@ -50,6 +50,7 @@ cpu0: cpu@0 {
next-level-cache = <&L2_0>;
operating-points-v2 = <&a53_opp_table>;
clocks = <&k3_clks 135 0>;
+ #cooling-cells = <2>;
};
cpu1: cpu@1 {
@@ -66,6 +67,7 @@ cpu1: cpu@1 {
next-level-cache = <&L2_0>;
operating-points-v2 = <&a53_opp_table>;
clocks = <&k3_clks 136 0>;
+ #cooling-cells = <2>;
};
cpu2: cpu@2 {
@@ -82,6 +84,7 @@ cpu2: cpu@2 {
next-level-cache = <&L2_0>;
operating-points-v2 = <&a53_opp_table>;
clocks = <&k3_clks 137 0>;
+ #cooling-cells = <2>;
};
cpu3: cpu@3 {
@@ -98,6 +101,7 @@ cpu3: cpu@3 {
next-level-cache = <&L2_0>;
operating-points-v2 = <&a53_opp_table>;
clocks = <&k3_clks 138 0>;
+ #cooling-cells = <2>;
};
};
--
2.25.1
next reply other threads:[~2025-05-06 11:42 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-05-06 11:41 Daniel Schultz [this message]
2025-05-06 11:41 ` [PATCH v2 2/2] arm64: dts: ti: k3-am62x-phyboard-lyra-gpio-fan: Update cooling maps Daniel Schultz
2025-05-07 5:38 ` [Upstream] " Wadim Egorov
2025-05-06 18:35 ` [PATCH v2 1/2] arm64: dts: ti: k3-am62a: Enable CPU freq throttling on thermal alert Bryan Brattlof
2025-05-09 12:20 ` Nishanth Menon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250506114134.3514899-1-d.schultz@phytec.de \
--to=d.schultz@phytec.de \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh@kernel.org \
--cc=upstream@lists.phytec.de \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®