* [PATCH v7 1/2] arm64: dts: qcom: qcs615: add a PCIe port for WLAN
2025-07-27 10:22 [PATCH v7 0/2] Enable WiFi/BT node for qcs615 ride board Yu Zhang(Yuriy)
@ 2025-07-27 10:22 ` Yu Zhang(Yuriy)
2025-07-27 10:22 ` [PATCH v7 2/2] arm64: dts: qcom: qcs615-ride: Enable WiFi/BT nodes Yu Zhang(Yuriy)
2025-08-11 18:41 ` [PATCH v7 0/2] Enable WiFi/BT node for qcs615 ride board Bjorn Andersson
2 siblings, 0 replies; 5+ messages in thread
From: Yu Zhang(Yuriy) @ 2025-07-27 10:22 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Dmitry Baryshkov
Cc: linux-arm-msm, devicetree, linux-kernel, Yu Zhang (Yuriy), Konrad Dybcio
Add an original PCIe port for WLAN. This port will be referenced and
supplemented by specific WLAN devices.
Signed-off-by: Yu Zhang (Yuriy) <yu.zhang@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/qcs615.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs615.dtsi b/arch/arm64/boot/dts/qcom/qcs615.dtsi
index f4b51cca17de5518aad4332330340a59edfdc7ec..b4fbed517cde18e088096d182fe6b482363e403d 100644
--- a/arch/arm64/boot/dts/qcom/qcs615.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs615.dtsi
@@ -1173,6 +1173,15 @@ opp-5000000 {
opp-peak-kBps = <500000 1>;
};
};
+
+ pcie_port0: pcie@0 {
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ bus-range = <0x01 0xff>;
+ };
};
pcie_phy: phy@1c0e000 {
--
2.34.1
^ permalink raw reply [flat|nested] 5+ messages in thread* [PATCH v7 2/2] arm64: dts: qcom: qcs615-ride: Enable WiFi/BT nodes
2025-07-27 10:22 [PATCH v7 0/2] Enable WiFi/BT node for qcs615 ride board Yu Zhang(Yuriy)
2025-07-27 10:22 ` [PATCH v7 1/2] arm64: dts: qcom: qcs615: add a PCIe port for WLAN Yu Zhang(Yuriy)
@ 2025-07-27 10:22 ` Yu Zhang(Yuriy)
2025-07-27 16:19 ` Dmitry Baryshkov
2025-08-11 18:41 ` [PATCH v7 0/2] Enable WiFi/BT node for qcs615 ride board Bjorn Andersson
2 siblings, 1 reply; 5+ messages in thread
From: Yu Zhang(Yuriy) @ 2025-07-27 10:22 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Dmitry Baryshkov
Cc: linux-arm-msm, devicetree, linux-kernel, Yu Zhang (Yuriy)
Enable WiFi/BT on qcs615-ride by adding a node for the PMU module of the
WCN6855 and assigning its LDO power outputs to the existing WiFi/BT
module.
Signed-off-by: Yu Zhang(Yuriy) <yu.zhang@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/qcs615-ride.dts | 135 +++++++++++++++++++++++++++++++
1 file changed, 135 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
index 011f8ae077c256f079ce1b07720374a9bf721488..7d8064303547e8be1e749cffc8f3ec8d3f3ec59b 100644
--- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
@@ -18,6 +18,7 @@ aliases {
mmc0 = &sdhc_1;
mmc1 = &sdhc_2;
serial0 = &uart0;
+ serial1 = &uart7;
};
chosen {
@@ -38,6 +39,22 @@ xo_board_clk: xo-board-clk {
};
};
+ vreg_conn_1p8: regulator-conn-1p8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_conn_1p8";
+ startup-delay-us = <4000>;
+ enable-active-high;
+ gpio = <&pm8150_gpios 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ vreg_conn_pa: regulator-conn-pa {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_conn_pa";
+ startup-delay-us = <4000>;
+ enable-active-high;
+ gpio = <&pm8150_gpios 6 GPIO_ACTIVE_HIGH>;
+ };
+
regulator-usb2-vbus {
compatible = "regulator-fixed";
regulator-name = "USB2_VBUS";
@@ -47,6 +64,69 @@ regulator-usb2-vbus {
enable-active-high;
regulator-always-on;
};
+
+ wcn6855-pmu {
+ compatible = "qcom,wcn6855-pmu";
+
+ pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
+ pinctrl-names = "default";
+
+ bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+ wlan-enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+
+ vddio-supply = <&vreg_conn_pa>;
+ vddaon-supply = <&vreg_s5a>;
+ vddpmu-supply = <&vreg_conn_1p8>;
+ vddpmumx-supply = <&vreg_conn_1p8>;
+ vddpmucx-supply = <&vreg_conn_pa>;
+ vddrfa0p95-supply = <&vreg_s5a>;
+ vddrfa1p3-supply = <&vreg_s6a>;
+ vddrfa1p9-supply = <&vreg_l15a>;
+ vddpcie1p3-supply = <&vreg_s6a>;
+ vddpcie1p9-supply = <&vreg_l15a>;
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p7: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p7";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
};
&apps_rsc {
@@ -234,6 +314,25 @@ &pcie_phy {
status = "okay";
};
+&pcie_port0 {
+ wifi@0 {
+ compatible = "pci17cb,1103";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ qcom,calibration-variant = "QC_QCS615_Ride";
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ };
+};
+
&pm8150_gpios {
usb2_en: usb2-en-state {
pins = "gpio10";
@@ -257,6 +356,10 @@ &qupv3_id_0 {
status = "okay";
};
+&qupv3_id_1 {
+ status = "okay";
+};
+
&remoteproc_adsp {
firmware-name = "qcom/qcs615/adsp.mbn";
@@ -274,6 +377,13 @@ &rpmhcc {
};
&tlmm {
+ bt_en_state: bt-en-state {
+ pins = "gpio85";
+ function = "gpio";
+ bias-pull-down;
+ output-low;
+ };
+
pcie_default_state: pcie-default-state {
clkreq-pins {
pins = "gpio90";
@@ -296,6 +406,13 @@ wake-pins {
bias-pull-up;
};
};
+
+ wlan_en_state: wlan-en-state {
+ pins = "gpio98";
+ function = "gpio";
+ bias-pull-down;
+ output-low;
+ };
};
&sdhc_1 {
@@ -336,6 +453,24 @@ &uart0 {
status = "okay";
};
+&uart7 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn6855-bt";
+ firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv";
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+ };
+};
+
&usb_1_hsphy {
vdd-supply = <&vreg_l5a>;
vdda-pll-supply = <&vreg_l12a>;
--
2.34.1
^ permalink raw reply [flat|nested] 5+ messages in thread