mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: YijieYang <yijie.yang@oss.qualcomm.com>
To: Vinod Koul <vkoul@kernel.org>,
	Andrew Lunn <andrew+netdev@lunn.ch>,
	"David S. Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	Maxime Coquelin <mcoquelin.stm32@gmail.com>,
	Alexandre Torgue <alexandre.torgue@foss.st.com>,
	Bjorn Andersson <andersson@kernel.org>,
	Konrad Dybcio <konradybcio@kernel.org>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Richard Cochran <richardcochran@gmail.com>
Cc: netdev@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	linux-stm32@st-md-mailman.stormreply.com,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
	stable+noautosel@kernel.org,
	Yijie Yang <yijie.yang@oss.qualcomm.com>,
	Yijie Yang <quic_yijiyang@quicinc.com>,
	Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Subject: [PATCH v4 4/6] arm64: dts: qcom: qcs615-ride: Enable ethernet node
Date: Tue, 19 Aug 2025 14:35:59 +0800	[thread overview]
Message-ID: <20250819-qcs615_eth-v4-4-5050ed3402cb@oss.qualcomm.com> (raw)
In-Reply-To: <20250819-qcs615_eth-v4-0-5050ed3402cb@oss.qualcomm.com>

From: Yijie Yang <quic_yijiyang@quicinc.com>

Enable the ethernet node, add the phy node and pinctrl for ethernet.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Yijie Yang <quic_yijiyang@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcs615-ride.dts | 104 +++++++++++++++++++++++++++++++
 1 file changed, 104 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
index 59582d3dc4c4..05d8609c0483 100644
--- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
@@ -288,6 +288,59 @@ vreg_l17a: ldo17 {
 	};
 };
 
+&ethernet {
+	pinctrl-0 = <&ethernet_defaults>;
+	pinctrl-names = "default";
+
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii-id";
+
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	status = "okay";
+
+	mdio: mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rgmii_phy: phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0x7>;
+
+			interrupts-extended = <&tlmm 121 IRQ_TYPE_EDGE_FALLING>;
+			device_type = "ethernet-phy";
+			reset-gpios = <&tlmm 104 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <11000>;
+			reset-deassert-us = <70000>;
+		};
+	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <1>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <1>;
+		snps,tx-sched-wrr;
+
+		queue0 {
+			snps,weight = <0x10>;
+			snps,dcb-algorithm;
+			snps,priority = <0x0>;
+		};
+	};
+};
+
 &gcc {
 	clocks = <&rpmhcc RPMH_CXO_CLK>,
 		 <&rpmhcc RPMH_CXO_CLK_A>,
@@ -446,6 +499,57 @@ &sdhc_2 {
 	status = "okay";
 };
 
+&tlmm {
+	ethernet_defaults: ethernet-defaults-state {
+		mdc-pins {
+			pins = "gpio113";
+			function = "rgmii";
+			bias-pull-up;
+		};
+
+		mdio-pins {
+			pins = "gpio114";
+			function = "rgmii";
+			bias-pull-up;
+		};
+
+		rgmii-rx-pins {
+			pins = "gpio81", "gpio82", "gpio83", "gpio102", "gpio103", "gpio112";
+			function = "rgmii";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+		rgmii-tx-pins {
+			pins = "gpio92", "gpio93", "gpio94", "gpio95", "gpio96", "gpio97";
+			function = "rgmii";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+
+		phy-intr-pins {
+			pins = "gpio121";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <8>;
+		};
+
+		pps-pins {
+			pins = "gpio91";
+			function = "rgmii";
+			bias-disable;
+			drive-strength = <8>;
+		};
+
+		phy-reset-pins {
+			pins = "gpio104";
+			function = "gpio";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+	};
+};
+
 &uart0 {
 	status = "okay";
 };

-- 
2.34.1


  parent reply	other threads:[~2025-08-19  6:37 UTC|newest]

Thread overview: 19+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-08-19  6:35 [PATCH v4 0/6] Enable ethernet on qcs615 Yijie Yang
2025-08-19  6:35 ` [PATCH v4 1/6] net: stmmac: Add support for 10 Mbps and 100 Mbps Ethernet speeds Yijie Yang
2025-08-19  6:35 ` [PATCH v4 2/6] net: stmmac: Inverse the phy-mode definition Yijie Yang
2025-08-19 16:20   ` Andrew Lunn
2025-08-21  2:22     ` Yijie Yang
2025-08-21  3:33       ` Andrew Lunn
2025-08-19  6:35 ` [PATCH v4 3/6] arm64: dts: qcom: qcs615: add ethernet node YijieYang
2025-08-19  6:44   ` Krzysztof Kozlowski
2025-08-19  6:51     ` Yijie Yang
2025-08-19  7:15       ` Krzysztof Kozlowski
2025-08-19  9:04         ` Yijie Yang
2025-08-19  9:08           ` Krzysztof Kozlowski
2025-08-20  8:57             ` Yijie Yang
2025-08-20 13:08               ` Krzysztof Kozlowski
2025-08-19  6:35 ` YijieYang [this message]
2025-08-19 16:24   ` [PATCH v4 4/6] arm64: dts: qcom: qcs615-ride: Enable " Andrew Lunn
2025-08-20  3:18     ` Yijie Yang
2025-08-19  6:36 ` [PATCH v4 5/6] arm64: dts: qcom: qcs404: Inverse phy-mode for EVB-4000 Yijie Yang
2025-08-19  6:36 ` [PATCH v4 6/6] arm64: dts: qcom: sa8155p-adp: Inverse phy-mode Yijie Yang

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20250819-qcs615_eth-v4-4-5050ed3402cb@oss.qualcomm.com \
    --to=yijie.yang@oss.qualcomm.com \
    --cc=alexandre.torgue@foss.st.com \
    --cc=andersson@kernel.org \
    --cc=andrew+netdev@lunn.ch \
    --cc=conor+dt@kernel.org \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=edumazet@google.com \
    --cc=konrad.dybcio@oss.qualcomm.com \
    --cc=konradybcio@kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=kuba@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-stm32@st-md-mailman.stormreply.com \
    --cc=mcoquelin.stm32@gmail.com \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    --cc=quic_yijiyang@quicinc.com \
    --cc=richardcochran@gmail.com \
    --cc=robh@kernel.org \
    --cc=stable+noautosel@kernel.org \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®