[PATCH v12 0/3] Initial support for Qualcomm Hamoa IOT EVK board

[PATCH v12 0/3] Initial support for Qualcomm Hamoa IOT EVK board

[Yijie Yang]

Introduce the device tree, DT bindings, and driver modifications required
to bring up the HAMOA-IOT-EVK evaluation board—based on the X1E80100 SoC—to
a UART shell.
This patch set focuses on two key hardware components: the HAMOA-IOT-SOM
and the HAMOA-IOT-EVK carrier board.
The HAMOA-IOT-SOM is a compact System on Module that integrates the SoC,
GPIOs, and PMICs. It is designed to be modular and can be paired with
various carrier boards to support different use cases.
The HAMOA-IOT-EVK is one such carrier board, designed for IoT scenarios.
It provides essential peripherals such as UART, on-board PMICs, and
USB-related components.
Together, these components form a flexible and scalable platform, and this
patch set enables their initial bring-up through proper device tree
configuration and driver support.

Qualcomm SoCs often have multiple product variants, each identified by a
different SoC ID. For instance, the x1e80100 SoC has closely related
variants such as x1e78100 and x1e001de. This diversity in SoC identifiers
can lead to confusion and unnecessary maintenance complexity in the device
tree and related subsystems.
To address this, code names offer a more consistent and project-agnostic
way to represent SoC families. They tend to remain stable across
development efforts.
This patch series introduces "hamoa" as the codename for the x1e80100 SoC.
Going forward, all x1e80100-related variants—including x1e81000 and others
in the same family—will be represented under the "hamoa" designation in the
device tree.
This improves readability, streamlines future maintenance, and aligns with
common naming practices across Qualcomm-based platforms. 

Features added and enabled:
- UART
- On-board regulators
- Regulators on the SOM
- PMIC GLINK
- USB0 through USB6 and their PHYs
- Embedded USB (eUSB) repeaters
- USB Type-C mux
- PCIe6a and its PHY
- PCIe4 and its PHY
- Reserved memory regions
- Pinctrl
- NVMe
- ADSP, CDSP
- WLAN, Bluetooth (M.2 interface)
- USB DisplayPort
- Graphic
- Audio
- Video

Depends on the following change to enable video:
https://lore.kernel.org/linux-arm-msm/20250911-x1e-iris-dt-v1-1-63caf0fd202c@linaro.org/

Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
---
Changes in v12:
- Remove the data-lanes property from the nodes: mdss_dp0_out, mdss_dp1_out, and mdss_dp2_out.
- Dropped the video commit as it duplicates Stephan's work and marked it as a dependency here.
- Add 'regulator-boot-on' property to vreg_wcn_3p3.
- Fix incorrect comments: change 'CRD' to 'EVK'.
- Remove dt-bindings dependency for x1e80100 Iris.
- Link to v11: https://lore.kernel.org/r/20250910-hamoa_initial-v11-0-38ed7f2015f7@oss.qualcomm.com

Changes in v11:
- Update the high-speed PHY repeater for the USB MP to the correct one.
- Update base commit.
- Format the audio-routing property and the i2c5 device node.
- Link to v10: https://lore.kernel.org/r/20250909-hamoa_initial-v10-0-ec10057ffcd2@oss.qualcomm.com

Changes in v10:
- Update the commit description.
- Remove the redundant space in 'stdout-path'.
- Move GPU nodes to the SoM's .dtsi file.
- Integrate the changes that enable video support into this patch series.
- Link to v9: https://lore.kernel.org/r/20250904-hamoa_initial-v9-0-d73213fa7542@oss.qualcomm.com

Changes in v9:
- Sort the nodes within the root node in alphabetical order.
- Add WLAN control pin to the PMU.
- Link to v8: https://lore.kernel.org/r/20250828-hamoa_initial-v8-0-c9d173072a5c@oss.qualcomm.com

Changes in v8:
- Change the style of how collaborators are listed.
- Link to v7: https://lore.kernel.org/r/20250827-hamoa_initial-v7-0-f9b81d564bb2@oss.qualcomm.com

Changes in v7:
- Configure the EDP regulator to boot-on.
- Change back to a year‑less copyright statement.
- Update base commit.
- Link to v6: https://lore.kernel.org/r/20250821-hamoa_initial-v6-0-72e4e01a55d0@oss.qualcomm.com

Changes in v6:
- Restore the full change log for each revision.
- Merge the changes related to Audio and Graphics into the patch series.
- Link to v5: https://lore.kernel.org/r/20250814-hamoa_initial-v5-0-817a9c6e8d47@oss.qualcomm.com

Changes in v5:
- Update base commit.
- Drop an already merged patch:
https://lore.kernel.org/all/20250804-hamoa_initial-v4-2-19edbb28677b@oss.qualcomm.com/
- Link to v4: https://lore.kernel.org/r/20250804-hamoa_initial-v4-0-19edbb28677b@oss.qualcomm.com

Changes in v4:
- Update commit messages.
- Update base commit.
- Update the format of the node mdss_dp3_out.
- Add comments to clarify certain nodes.
- Update the configuration of regulator-wcn-3p3 from regulator-boot-on to regulator-always-on.
- Link to v3: https://lore.kernel.org/r/20250729-hamoa_initial-v3-0-806e092789dc@oss.qualcomm.com

Changes in v3:
- Add compatible string and dt-bindings for SOM.
- Restore PMU-related regulators to comply with dt-binding rules and enable kernel-level power management.
- Adjust commit description accordingly.
- Link to v2: https://lore.kernel.org/r/20250724-hamoa_initial-v2-0-91b00c882d11@oss.qualcomm.com

Changes in v2:
- Merge the compatible rules and remove the compatible string map.
- Align the ADSP and CDSP firmware paths with other x1e80100 platforms.
- Remove the regulators on the M.2 card, as well as those managed by UEFI on this board.
- Merge another patch series that enables USB DisplayPort functionality on this platform: https://lore.kernel.org/all/20250723-x1e-evk-dp-v1-1-be76ce53b9b8@quicinc.com/
- Link to v1: https://lore.kernel.org/r/20250716-hamoa_initial-v1-0-f6f5d0f9a163@oss.qualcomm.com

---
Yijie Yang (3):
      dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board
      arm64: dts: qcom: Add HAMOA-IOT-SOM platform
      arm64: dts: qcom: Add base HAMOA-IOT-EVK board

 Documentation/devicetree/bindings/arm/qcom.yaml |    6 +
 arch/arm64/boot/dts/qcom/Makefile               |    1 +
 arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts      | 1222 +++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi     |  619 ++++++++++++
 4 files changed, 1848 insertions(+)
---
base-commit: 51095600e8c19d53729a7fbd273abc4435a25e9b
change-id: 20250604-hamoa_initial-0cd7036d7271
prerequisite-message-id: <20250911-x1e-iris-dt-v1-1-63caf0fd202c@linaro.org>
prerequisite-patch-id: 00f818253d1f1613b0263ee46cbbcd8ff9a01642
prerequisite-patch-id: 733387b3347d71183bf5859b70b787a95b0d1c4d
prerequisite-patch-id: a39bcc0bb375eada0214efe3e40d5c2f3405c5dc
prerequisite-patch-id: 2c2ec1f8e5de8cb33e63fddcdada4e9c0dacc6c1

Best regards,
--  
Yijie Yang <yijie.yang@oss.qualcomm.com>

[PATCH v12 1/3] dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board

[Yijie Yang]

Document the device tree binding for the HAMOA-IOT-EVK board, which uses
the Qualcomm X1E80100 SoC.

The EVK consists of a carrier board and a modular System-on-Module (SoM).
The SoM integrates the SoC, PMICs, and essential GPIOs, while the EVK
carrier board provides additional peripherals such as UART and USB
interfaces.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 0a3222d6f368..349f526df35e 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1074,6 +1074,12 @@ properties:
               - qcom,x1e80100-qcp
           - const: qcom,x1e80100
 
+      - items:
+          - enum:
+              - qcom,hamoa-iot-evk
+          - const: qcom,hamoa-iot-som
+          - const: qcom,x1e80100
+
       - items:
           - enum:
               - asus,zenbook-a14-ux3407qa

-- 
2.34.1

[PATCH v12 2/3] arm64: dts: qcom: Add HAMOA-IOT-SOM platform

[Yijie Yang]

The HAMOA-IOT-SOM is a compact computing module that integrates a System
on Chip (SoC) — specifically the x1e80100 — along with essential
components optimized for IoT applications. It is designed to be mounted on
carrier boards, enabling the development of complete embedded systems.

Make the following peripherals on the SOM enabled:
- Regulators on the SOM
- Reserved memory regions
- PCIe6a and its PHY
- PCIe4 and its PHY
- USB0 through USB6 and their PHYs
- ADSP, CDSP
- Graphic
- Video

Written in collaboration with Yingying Tang (PCIe4)
<quic_yintang@quicinc.com> and Wangao Wang (Video)
<quic_wangaow@quicinc.com>.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi | 619 ++++++++++++++++++++++++++++
 1 file changed, 619 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi b/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi
new file mode 100644
index 000000000000..1aead50b8920
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi
@@ -0,0 +1,619 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include "x1e80100.dtsi"
+#include "x1e80100-pmics.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+/ {
+	reserved-memory {
+		linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x0 0x8000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+};
+
+&apps_rsc {
+	/* PMC8380C_B */
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob2>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l12-supply = <&vreg_s5j_1p2>;
+		vdd-l15-supply = <&vreg_s4c_1p8>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_1p8: ldo4 {
+			regulator-name = "vreg_l4b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p0: ldo5 {
+			regulator-name = "vreg_l5b_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p8: ldo7 {
+			regulator-name = "vreg_l7b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_3p0: ldo8 {
+			regulator-name = "vreg_l8b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_1p8: ldo10 {
+			regulator-name = "vreg_l10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p2: ldo12 {
+			regulator-name = "vreg_l12b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p0: ldo14 {
+			regulator-name = "vreg_l14b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l16b_2p9: ldo16 {
+			regulator-name = "vreg_l16b_2p9";
+			regulator-min-microvolt = <2912000>;
+			regulator-max-microvolt = <2912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	/* PMC8380VE_C */
+	regulators-1 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s4c_1p8: smps4 {
+			regulator-name = "vreg_s4c_1p8";
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c_1p2: ldo1 {
+			regulator-name = "vreg_l1c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_0p8: ldo2 {
+			regulator-name = "vreg_l2c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_0p8: ldo3 {
+			regulator-name = "vreg_l3c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	/* PMC8380_D */
+	regulators-2 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s4c_1p8>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_l1d_0p8: ldo1 {
+			regulator-name = "vreg_l1d_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2d_0p9: ldo2 {
+			regulator-name = "vreg_l2d_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3d_1p8: ldo3 {
+			regulator-name = "vreg_l3d_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	/* PMC8380_E */
+	regulators-3 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	/* PMC8380_F */
+	regulators-4 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_s1f_0p7: smps1 {
+			regulator-name = "vreg_s1f_0p7";
+			regulator-min-microvolt = <700000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_1p0: ldo1 {
+			regulator-name = "vreg_l1f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_1p0: ldo2 {
+			regulator-name = "vreg_l2f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_1p0: ldo3 {
+			regulator-name = "vreg_l3f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	/* PMC8380VE_I */
+	regulators-6 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "i";
+
+		vdd-l1-supply = <&vreg_s4c_1p8>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+
+		vreg_s1i_0p9: smps1 {
+			regulator-name = "vreg_s1i_0p9";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2i_1p0: smps2 {
+			regulator-name = "vreg_s2i_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1i_1p8: ldo1 {
+			regulator-name = "vreg_l1i_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2i_1p2: ldo2 {
+			regulator-name = "vreg_l2i_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3i_0p8: ldo3 {
+			regulator-name = "vreg_l3i_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	/* PMC8380VE_J */
+	regulators-7 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "j";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_s5j_1p2: smps5 {
+			regulator-name = "vreg_s5j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1j_0p8: ldo1 {
+			regulator-name = "vreg_l1j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2j_1p2: ldo2 {
+			regulator-name = "vreg_l2j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1256000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3j_0p8: ldo3 {
+			regulator-name = "vreg_l3j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&iris {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/x1e80100/gen70500_zap.mbn";
+};
+
+&pcie4 {
+	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie4_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3i_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie6a {
+	perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie6a_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l1d_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
+&qupv3_2 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/adsp.mbn",
+			"qcom/x1e80100/adsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/cdsp.mbn",
+			"qcom/x1e80100/cdsp_dtb.mbn";
+
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <34 2>, /* TPM LP & INT */
+			       <44 4>; /* SPI (TPM) */
+
+	pcie4_default: pcie4-default-state {
+		clkreq-n-pins {
+			pins = "gpio147";
+			function = "pcie4_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio146";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio148";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie6a_default: pcie6a-default-state {
+		clkreq-n-pins {
+			pins = "gpio153";
+			function = "pcie6a_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio152";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio154";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+
+		};
+	};
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l1j_0p8>;
+
+	status = "okay";
+};
+
+&usb_1_ss1 {
+	status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_ss1_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l2d_0p9>;
+
+	status = "okay";
+};
+
+&usb_1_ss2 {
+	status = "okay";
+};
+
+&usb_1_ss2_dwc3 {
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_ss2_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss2_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l2d_0p9>;
+
+	status = "okay";
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_mp_hsphy1 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};

-- 
2.34.1

[PATCH v12 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board

[Yijie Yang]

The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of
the Hamoa IoT SoM and a carrier board. Together, they form a complete
embedded system capable of booting to UART.

Make the following peripherals on the carrier board enabled:
- UART
- On-board regulators
- USB Type-C mux
- Pinctrl
- Embedded USB (EUSB) repeaters
- NVMe
- pmic-glink
- USB DisplayPorts
- Bluetooth
- WLAN
- Audio

Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>,
Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth)
<quic_shuaz@quicinc.com>, Yingying Tang (WLAN) <quic_yintang@quicinc.com>,
and Yongxing Mou (USB DisplayPorts) <quic_yongmou@quicinc.com>.

Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile          |    1 +
 arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1222 ++++++++++++++++++++++++++++
 2 files changed, 1223 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 5b52f9e4e5f3..577a956b5409 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= apq8039-t2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8094-sony-xperia-kitakami-karin_windy.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-db820c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-ifc6640.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= hamoa-iot-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5018-rdp432-c2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5018-tplink-archer-ax55-v1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= ipq5332-rdp441.dtb
diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
new file mode 100644
index 000000000000..df8d6e5c1f45
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
@@ -0,0 +1,1222 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+
+#include "hamoa-iot-som.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. Hamoa IoT EVK";
+	compatible = "qcom,hamoa-iot-evk", "qcom,hamoa-iot-som", "qcom,x1e80100";
+	chassis-type = "embedded";
+
+	aliases {
+		serial0 = &uart21;
+		serial1 = &uart14;
+	};
+
+	wcd938x: audio-codec {
+		compatible = "qcom,wcd9385-codec";
+
+		pinctrl-0 = <&wcd_default>;
+		pinctrl-names = "default";
+
+		reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000
+							 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		vdd-buck-supply = <&vreg_l15b_1p8>;
+		vdd-rxtx-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob1>;
+
+		#sound-dai-cells = <1>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 123 GPIO_ACTIVE_HIGH>,
+				    <&tlmm 125 GPIO_ACTIVE_HIGH>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss0_sbu: endpoint {
+						remote-endpoint = <&usb_1_ss0_sbu_mux>;
+					};
+				};
+			};
+		};
+
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss1_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss1_ss_in: endpoint {
+						remote-endpoint = <&retimer_ss1_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss1_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss1_con_sbu_out>;
+					};
+				};
+			};
+		};
+
+		connector@2 {
+			compatible = "usb-c-connector";
+			reg = <2>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss2_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss2_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss2_ss_in: endpoint {
+						remote-endpoint = <&retimer_ss2_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss2_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss2_con_sbu_out>;
+					};
+				};
+			};
+		};
+	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_nvme: regulator-nvme {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_NVME_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&nvme_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	/* Left unused as the retimer is not used on this board. */
+	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_1p15: regulator-rtmr1-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_1p8: regulator-rtmr1-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr1_3p3: regulator-rtmr1-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR1_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb1_pwr_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr2_1p15: regulator-rtmr2-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR2_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&tlmm 189 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb2_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr2_1p8: regulator-rtmr2-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR2_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 126 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb2_pwr_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr2_3p3: regulator-rtmr2-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR2_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 187 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb2_pwr_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/*
+	 * TODO: These two regulators are actually part of the removable M.2
+	 * card and not the EVK mainboard. Need to describe this differently.
+	 * Functionally it works correctly, because all we need to do is to
+	 * turn on the actual 3.3V supply above.
+	 */
+	vreg_wcn_0p95: regulator-wcn-0p95 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_0P95";
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_1p9: regulator-wcn-1p9 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_1P9";
+		regulator-min-microvolt = <1900000>;
+		regulator-max-microvolt = <1900000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_3p3: regulator-wcn-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wcn_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vreg_wwan: regulator-wwan {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDX_VPH_PWR";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 221 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wwan_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	sound {
+		compatible = "qcom,x1e80100-sndcard";
+		model = "X1E80100-EVK";
+		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
+				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
+				"WooferRight IN", "WSA2 WSA_SPK2 OUT",
+				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
+				"IN1_HPHL", "HPHL_OUT",
+				"IN2_HPHR", "HPHR_OUT",
+				"AMIC2", "MIC BIAS2",
+				"VA DMIC0", "MIC BIAS3",
+				"VA DMIC1", "MIC BIAS3",
+				"VA DMIC2", "MIC BIAS1",
+				"VA DMIC3", "MIC BIAS1",
+				"TX SWR_INPUT1", "ADC2_OUTPUT";
+
+		wcd-playback-dai-link {
+			link-name = "WCD Playback";
+
+			codec {
+				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			codec {
+				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			codec {
+				sound-dai = <&left_woofer>,
+					    <&left_tweeter>,
+					    <&swr0 0>,
+					    <&lpass_wsamacro 0>,
+					    <&right_woofer>,
+					    <&right_tweeter>,
+					    <&swr3 0>,
+					    <&lpass_wsa2macro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	usb-1-ss0-sbu-mux {
+		compatible = "onnn,fsusb42", "gpio-sbu-mux";
+
+		enable-gpios = <&tlmm 168 GPIO_ACTIVE_LOW>;
+		select-gpios = <&tlmm 167 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&usb_1_ss0_sbu_default>;
+		pinctrl-names = "default";
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			usb_1_ss0_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_ss0_sbu>;
+			};
+		};
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		vdd-supply = <&vreg_wcn_0p95>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_wcn_0p95>;
+		vdddig-supply = <&vreg_wcn_0p95>;
+		vddrfa1p2-supply = <&vreg_wcn_1p9>;
+		vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+		bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+		wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&wcn_bt_en>;
+		pinctrl-names = "default";
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x08>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK5>;
+
+		vdd-supply = <&vreg_rtmr2_1p15>;
+		vdd33-supply = <&vreg_rtmr2_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr2_3p3>;
+		vddar-supply = <&vreg_rtmr2_1p15>;
+		vddat-supply = <&vreg_rtmr2_1p15>;
+		vddio-supply = <&vreg_rtmr2_1p8>;
+
+		reset-gpios = <&tlmm 185 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr2_default>;
+		pinctrl-names = "default";
+
+		orientation-switch;
+		retimer-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss2_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss2_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss2_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss2_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss2_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss2_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	eusb3_repeater: redriver@47 {
+		compatible = "nxp,ptn3222";
+		reg = <0x47>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb3_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb5_repeater: redriver@43 {
+		compatible = "nxp,ptn3222";
+		reg = <0x43>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb5_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb6_repeater: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb6_reset_n>;
+		pinctrl-names = "default";
+	};
+};
+
+&i2c7 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x8>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK4>;
+
+		vdd-supply = <&vreg_rtmr1_1p15>;
+		vdd33-supply = <&vreg_rtmr1_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr1_3p3>;
+		vddar-supply = <&vreg_rtmr1_1p15>;
+		vddat-supply = <&vreg_rtmr1_1p15>;
+		vddio-supply = <&vreg_rtmr1_1p8>;
+
+		reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr1_default>;
+		pinctrl-names = "default";
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss1_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss1_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss1_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss1_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss1_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
+&lpass_tlmm {
+	spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	spkr_23_sd_n_active: spkr-23-sd-n-active-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+	pinctrl-names = "default";
+
+	vdd-micb-supply = <&vreg_l1b_1p8>;
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+	status = "okay";
+};
+
+&mdss_dp1_out {
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp2 {
+	status = "okay";
+};
+
+&mdss_dp2_out {
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+	/delete-property/ #sound-dai-cells;
+
+	pinctrl-0 = <&edp0_hpd_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+			power-supply = <&vreg_edp_3p3>;
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+};
+
+&mdss_dp3_out {
+	data-lanes = <0 1 2 3>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+	remote-endpoint = <&edp_panel_in>;
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie6a {
+	vddpe-3v3-supply = <&vreg_nvme>;
+};
+
+&pm8550_gpios {
+	rtmr0_default: rtmr0-reset-n-active-state {
+		pins = "gpio10";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+
+	usb0_3p3_reg_en: usb0-3p3-reg-en-state {
+		pins = "gpio11";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pm8550ve_9_gpios {
+	usb0_1p8_reg_en: usb0-1p8-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pmc8380_5_gpios {
+	usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&smb2360_0 {
+	status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&smb2360_1 {
+	status = "okay";
+};
+
+&smb2360_1_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l14b_3p0>;
+};
+
+&smb2360_2 {
+	status = "okay";
+};
+
+&smb2360_2_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l8b_3p0>;
+};
+
+&swr0 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Left Woofer */
+	left_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Left Tweeter */
+	left_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	/* WCD9385 RX */
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	/* WCD9385 TX */
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <2 2 3 4>;
+	};
+};
+
+&swr3 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Right Woofer */
+	right_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Right Tweeter */
+	right_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&tlmm {
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio70";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	eusb3_reset_n: eusb3-reset-n-state {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb5_reset_n: eusb5-reset-n-state {
+		pins = "gpio7";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+		output-low;
+	};
+
+	eusb6_reset_n: eusb6-reset-n-state {
+		pins = "gpio184";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+		output-low;
+	};
+
+	nvme_reg_en: nvme-reg-en-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rtmr1_default: rtmr1-reset-n-active-state {
+		pins = "gpio176";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rtmr2_default: rtmr2-reset-n-active-state {
+		pins = "gpio185";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb1_pwr_1p15_reg_en: usb1-pwr-1p15-reg-en-state {
+		pins = "gpio188";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb1_pwr_1p8_reg_en: usb1-pwr-1p8-reg-en-state {
+		pins = "gpio175";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb1_pwr_3p3_reg_en: usb1-pwr-3p3-reg-en-state {
+		pins = "gpio186";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb2_pwr_1p15_reg_en: usb2-pwr-1p15-reg-en-state {
+		pins = "gpio189";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb2_pwr_1p8_reg_en: usb2-pwr-1p8-reg-en-state {
+		pins = "gpio126";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb2_pwr_3p3_reg_en: usb2-pwr-3p3-reg-en-state {
+		pins = "gpio187";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	usb_1_ss0_sbu_default: usb-1-ss0-sbu-state {
+		mode-pins {
+			pins = "gpio166";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+			output-high;
+		};
+
+		oe-n-pins {
+			pins = "gpio168";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+		sel-pins {
+			pins = "gpio167";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+		};
+	};
+
+	wcd_default: wcd-reset-n-active-state {
+		pins = "gpio191";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	wcn_bt_en: wcn-bt-en-state {
+		pins = "gpio116";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wwan_sw_en: wwan-sw-en-state {
+		pins = "gpio221";
+		function = "gpio";
+		drive-strength = <4>;
+		bias-disable;
+	};
+
+	wcn_sw_en: wcn-sw-en-state {
+		pins = "gpio214";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	/* Switches USB signal routing between the USB connector and the Wi-Fi card. */
+	wcn_usb_sw_n: wcn-usb-sw-n-state {
+		pins = "gpio225";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+		max-speed = <3200000>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+	};
+};
+
+&uart21 {
+	compatible = "qcom,geni-debug-uart";
+
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_hsphy {
+	phys = <&smb2360_0_eusb2_repeater>;
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss0_ss_in>;
+};
+
+&usb_1_ss1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_hsphy {
+	phys = <&smb2360_1_eusb2_repeater>;
+};
+
+&usb_1_ss1_qmpphy_out {
+	remote-endpoint = <&retimer_ss1_ss_in>;
+};
+
+&usb_1_ss2_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss2_hs_in>;
+};
+
+&usb_1_ss2_hsphy {
+	phys = <&smb2360_2_eusb2_repeater>;
+};
+
+&usb_1_ss2_qmpphy_out {
+	remote-endpoint = <&retimer_ss2_ss_in>;
+};
+
+&usb_2_hsphy {
+	phys = <&eusb5_repeater>;
+
+	pinctrl-0 = <&wcn_usb_sw_n>;
+	pinctrl-names = "default";
+};
+
+&usb_mp_hsphy0 {
+	phys = <&eusb3_repeater>;
+};
+
+&usb_mp_hsphy1 {
+	phys = <&eusb6_repeater>;
+};

-- 
2.34.1

Re: [PATCH v12 2/3] arm64: dts: qcom: Add HAMOA-IOT-SOM platform

[Dmitry Baryshkov]

On Wed, Sep 17, 2025 at 10:58:59AM +0800, Yijie Yang wrote:
> The HAMOA-IOT-SOM is a compact computing module that integrates a System
> on Chip (SoC) — specifically the x1e80100 — along with essential
> components optimized for IoT applications. It is designed to be mounted on
> carrier boards, enabling the development of complete embedded systems.
> 
> Make the following peripherals on the SOM enabled:
> - Regulators on the SOM
> - Reserved memory regions
> - PCIe6a and its PHY
> - PCIe4 and its PHY
> - USB0 through USB6 and their PHYs
> - ADSP, CDSP
> - Graphic
> - Video
> 
> Written in collaboration with Yingying Tang (PCIe4)
> <quic_yintang@quicinc.com> and Wangao Wang (Video)
> <quic_wangaow@quicinc.com>.
> 
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
> ---
>  arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi | 619 ++++++++++++++++++++++++++++
>  1 file changed, 619 insertions(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

Re: [PATCH v12 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board

[Dmitry Baryshkov]

On Wed, Sep 17, 2025 at 10:59:00AM +0800, Yijie Yang wrote:
> The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of
> the Hamoa IoT SoM and a carrier board. Together, they form a complete
> embedded system capable of booting to UART.
> 
> Make the following peripherals on the carrier board enabled:
> - UART
> - On-board regulators
> - USB Type-C mux
> - Pinctrl
> - Embedded USB (EUSB) repeaters
> - NVMe
> - pmic-glink
> - USB DisplayPorts
> - Bluetooth
> - WLAN
> - Audio
> 
> Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>,
> Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth)
> <quic_shuaz@quicinc.com>, Yingying Tang (WLAN) <quic_yintang@quicinc.com>,
> and Yongxing Mou (USB DisplayPorts) <quic_yongmou@quicinc.com>.
> 
> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
> ---
>  arch/arm64/boot/dts/qcom/Makefile          |    1 +
>  arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1222 ++++++++++++++++++++++++++++
>  2 files changed, 1223 insertions(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

Re: [PATCH v12 0/3] Initial support for Qualcomm Hamoa IOT EVK board

[Bjorn Andersson]

On Wed, 17 Sep 2025 10:58:57 +0800, Yijie Yang wrote:
> Introduce the device tree, DT bindings, and driver modifications required
> to bring up the HAMOA-IOT-EVK evaluation board—based on the X1E80100 SoC—to
> a UART shell.
> This patch set focuses on two key hardware components: the HAMOA-IOT-SOM
> and the HAMOA-IOT-EVK carrier board.
> The HAMOA-IOT-SOM is a compact System on Module that integrates the SoC,
> GPIOs, and PMICs. It is designed to be modular and can be paired with
> various carrier boards to support different use cases.
> The HAMOA-IOT-EVK is one such carrier board, designed for IoT scenarios.
> It provides essential peripherals such as UART, on-board PMICs, and
> USB-related components.
> Together, these components form a flexible and scalable platform, and this
> patch set enables their initial bring-up through proper device tree
> configuration and driver support.
> 
> [...]

Applied, thanks!

[1/3] dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board
      commit: 458bb855f274e227618acfa8c098b8e4894d9cd9
[2/3] arm64: dts: qcom: Add HAMOA-IOT-SOM platform
      commit: 5098ae93ce44110a4d86574819b254fd126243af
[3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board
      commit: c11645afb0e228546279ad1b74826fffbfebbc7f

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>