mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
To: mkl@pengutronix.de, mani@kernel.org, thomas.kopp@microchip.com,
	mailhol.vincent@wanadoo.fr, robh@kernel.org, krzk+dt@kernel.org,
	conor+dt@kernel.org, linus.walleij@linaro.org, brgl@bgdev.pl,
	linux-can@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org
Cc: mukesh.savaliya@oss.qualcomm.com, anup.kulkarni@oss.qualcomm.com,
	Gregor Herburger <gregor.herburger@ew.tq-group.com>,
	Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Subject: [PATCH v5 1/6] can: mcp251xfd: move chip sleep mode into runtime pm
Date: Fri, 26 Sep 2025 19:00:13 +0530	[thread overview]
Message-ID: <20250926133018.3071446-2-viken.dadhaniya@oss.qualcomm.com> (raw)
In-Reply-To: <20250926133018.3071446-1-viken.dadhaniya@oss.qualcomm.com>

From: Marc Kleine-Budde <mkl@pengutronix.de>

This is a preparation patch to add GPIO support.

Up to now, the Vdd regulator and the clocks have been managed by
Runtime-PM (on systems without CONFIG_PM these remain permanently
switched on).

During the mcp251xfd_open() callback the mcp251xfd is powered,
soft-reset and configured. In mcp251xfd_stop() the chip is shut down
again. To support the on-chip GPIOs, the chip must be supplied with
power while GPIOs are being requested, even if the networking
interface is down.

To support this, move the functions mcp251xfd_chip_softreset() and
mcp251xfd_chip_clock_init() from mcp251xfd_chip_start() to
mcp251xfd_runtime_resume(). Instead of setting the controller to sleep
mode in mcp251xfd_chip_stop(), bring it into configuration mode. This
way it doesn't take part in bus activity and doesn't enter sleep mode.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Gregor Herburger <gregor.herburger@ew.tq-group.com>
Tested-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
---
 .../net/can/spi/mcp251xfd/mcp251xfd-core.c    | 91 ++++++++++++-------
 1 file changed, 57 insertions(+), 34 deletions(-)

diff --git a/drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c b/drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c
index 7450ea42c1ea..f9eabb1810cf 100644
--- a/drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c
+++ b/drivers/net/can/spi/mcp251xfd/mcp251xfd-core.c
@@ -767,21 +767,13 @@ static void mcp251xfd_chip_stop(struct mcp251xfd_priv *priv,
 	mcp251xfd_chip_interrupts_disable(priv);
 	mcp251xfd_chip_rx_int_disable(priv);
 	mcp251xfd_timestamp_stop(priv);
-	mcp251xfd_chip_sleep(priv);
+	mcp251xfd_chip_set_mode(priv, MCP251XFD_REG_CON_MODE_CONFIG);
 }
 
 static int mcp251xfd_chip_start(struct mcp251xfd_priv *priv)
 {
 	int err;
 
-	err = mcp251xfd_chip_softreset(priv);
-	if (err)
-		goto out_chip_stop;
-
-	err = mcp251xfd_chip_clock_init(priv);
-	if (err)
-		goto out_chip_stop;
-
 	err = mcp251xfd_chip_timestamp_init(priv);
 	if (err)
 		goto out_chip_stop;
@@ -1625,8 +1617,11 @@ static int mcp251xfd_open(struct net_device *ndev)
 		return err;
 
 	err = pm_runtime_resume_and_get(ndev->dev.parent);
-	if (err)
+	if (err) {
+		if (err == -ETIMEDOUT || err == -ENODEV)
+			pm_runtime_set_suspended(ndev->dev.parent);
 		goto out_close_candev;
+	}
 
 	err = mcp251xfd_ring_alloc(priv);
 	if (err)
@@ -1907,53 +1902,53 @@ static int mcp251xfd_register(struct mcp251xfd_priv *priv)
 	struct net_device *ndev = priv->ndev;
 	int err;
 
+	mcp251xfd_register_quirks(priv);
+
 	err = mcp251xfd_clks_and_vdd_enable(priv);
 	if (err)
 		return err;
 
-	pm_runtime_get_noresume(ndev->dev.parent);
-	err = pm_runtime_set_active(ndev->dev.parent);
-	if (err)
-		goto out_runtime_put_noidle;
-	pm_runtime_enable(ndev->dev.parent);
-
-	mcp251xfd_register_quirks(priv);
-
 	err = mcp251xfd_chip_softreset(priv);
 	if (err == -ENODEV)
-		goto out_runtime_disable;
+		goto out_clks_and_vdd_disable;
 	if (err)
 		goto out_chip_sleep;
 
 	err = mcp251xfd_chip_clock_init(priv);
 	if (err == -ENODEV)
-		goto out_runtime_disable;
+		goto out_clks_and_vdd_disable;
 	if (err)
 		goto out_chip_sleep;
 
+	pm_runtime_get_noresume(ndev->dev.parent);
+	err = pm_runtime_set_active(ndev->dev.parent);
+	if (err)
+		goto out_runtime_put_noidle;
+	pm_runtime_enable(ndev->dev.parent);
+
 	err = mcp251xfd_register_chip_detect(priv);
 	if (err)
-		goto out_chip_sleep;
+		goto out_runtime_disable;
 
 	err = mcp251xfd_register_check_rx_int(priv);
 	if (err)
-		goto out_chip_sleep;
+		goto out_runtime_disable;
 
 	mcp251xfd_ethtool_init(priv);
 
 	err = register_candev(ndev);
 	if (err)
-		goto out_chip_sleep;
+		goto out_runtime_disable;
 
 	err = mcp251xfd_register_done(priv);
 	if (err)
 		goto out_unregister_candev;
 
-	/* Put controller into sleep mode and let pm_runtime_put()
-	 * disable the clocks and vdd. If CONFIG_PM is not enabled,
-	 * the clocks and vdd will stay powered.
+	/* Put controller into Config mode and let pm_runtime_put()
+	 * put in sleep mode, disable the clocks and vdd. If CONFIG_PM
+	 * is not enabled, the clocks and vdd will stay powered.
 	 */
-	err = mcp251xfd_chip_sleep(priv);
+	err = mcp251xfd_chip_set_mode(priv, MCP251XFD_REG_CON_MODE_CONFIG);
 	if (err)
 		goto out_unregister_candev;
 
@@ -1963,12 +1958,13 @@ static int mcp251xfd_register(struct mcp251xfd_priv *priv)
 
 out_unregister_candev:
 	unregister_candev(ndev);
-out_chip_sleep:
-	mcp251xfd_chip_sleep(priv);
 out_runtime_disable:
 	pm_runtime_disable(ndev->dev.parent);
 out_runtime_put_noidle:
 	pm_runtime_put_noidle(ndev->dev.parent);
+out_chip_sleep:
+	mcp251xfd_chip_sleep(priv);
+out_clks_and_vdd_disable:
 	mcp251xfd_clks_and_vdd_disable(priv);
 
 	return err;
@@ -1980,10 +1976,12 @@ static inline void mcp251xfd_unregister(struct mcp251xfd_priv *priv)
 
 	unregister_candev(ndev);
 
-	if (pm_runtime_enabled(ndev->dev.parent))
+	if (pm_runtime_enabled(ndev->dev.parent)) {
 		pm_runtime_disable(ndev->dev.parent);
-	else
+	} else {
+		mcp251xfd_chip_sleep(priv);
 		mcp251xfd_clks_and_vdd_disable(priv);
+	}
 }
 
 static const struct of_device_id mcp251xfd_of_match[] = {
@@ -2206,16 +2204,41 @@ static void mcp251xfd_remove(struct spi_device *spi)
 
 static int __maybe_unused mcp251xfd_runtime_suspend(struct device *device)
 {
-	const struct mcp251xfd_priv *priv = dev_get_drvdata(device);
+	struct mcp251xfd_priv *priv = dev_get_drvdata(device);
 
+	mcp251xfd_chip_sleep(priv);
 	return mcp251xfd_clks_and_vdd_disable(priv);
 }
 
 static int __maybe_unused mcp251xfd_runtime_resume(struct device *device)
 {
-	const struct mcp251xfd_priv *priv = dev_get_drvdata(device);
+	struct mcp251xfd_priv *priv = dev_get_drvdata(device);
+	int err;
+
+	err = mcp251xfd_clks_and_vdd_enable(priv);
+	if (err)
+		return err;
 
-	return mcp251xfd_clks_and_vdd_enable(priv);
+	err = mcp251xfd_chip_softreset(priv);
+	if (err == -ENODEV)
+		goto out_clks_and_vdd_disable;
+	if (err)
+		goto out_chip_sleep;
+
+	err = mcp251xfd_chip_clock_init(priv);
+	if (err == -ENODEV)
+		goto out_clks_and_vdd_disable;
+	if (err)
+		goto out_chip_sleep;
+
+	return 0;
+
+out_chip_sleep:
+	mcp251xfd_chip_sleep(priv);
+out_clks_and_vdd_disable:
+	mcp251xfd_clks_and_vdd_disable(priv);
+
+	return err;
 }
 
 static const struct dev_pm_ops mcp251xfd_pm_ops = {
-- 
2.34.1


  reply	other threads:[~2025-09-26 13:30 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-09-26 13:30 [PATCH v5 0/6] can: mcp251xfd: add gpio functionality Viken Dadhaniya
2025-09-26 13:30 ` Viken Dadhaniya [this message]
2025-09-26 13:30 ` [PATCH v5 2/6] can: mcp251xfd: utilize gather_write function for all non-CRC writes Viken Dadhaniya
2025-09-26 13:30 ` [PATCH v5 3/6] can: mcp251xfd: add workaround for errata 5 Viken Dadhaniya
2025-09-26 13:30 ` [PATCH v5 4/6] can: mcp251xfd: only configure PIN1 when rx_int is set Viken Dadhaniya
2025-09-26 13:30 ` [PATCH v5 5/6] can: mcp251xfd: add gpio functionality Viken Dadhaniya
2025-09-29 13:38   ` Bartosz Golaszewski
2025-09-30 11:25     ` Viken Dadhaniya
2025-09-26 13:30 ` [PATCH v5 6/6] dt-bindings: can: mcp251xfd: add gpio-controller property Viken Dadhaniya

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20250926133018.3071446-2-viken.dadhaniya@oss.qualcomm.com \
    --to=viken.dadhaniya@oss.qualcomm.com \
    --cc=anup.kulkarni@oss.qualcomm.com \
    --cc=brgl@bgdev.pl \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=gregor.herburger@ew.tq-group.com \
    --cc=krzk+dt@kernel.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-can@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mailhol.vincent@wanadoo.fr \
    --cc=mani@kernel.org \
    --cc=mkl@pengutronix.de \
    --cc=mukesh.savaliya@oss.qualcomm.com \
    --cc=robh@kernel.org \
    --cc=thomas.kopp@microchip.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®