* [PATCH v2 1/5] arm64: dts: rockchip: move cpu_thermal node to the correct position
2025-11-12 21:42 [PATCH v2 0/5] Some cleanups and addition of another Qnap TSx33 device Heiko Stuebner
@ 2025-11-12 21:42 ` Heiko Stuebner
2025-11-12 21:42 ` [PATCH v2 2/5] arm64: dts: rockchip: describe mcu eeprom cells on rk3568-ts433 Heiko Stuebner
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Heiko Stuebner @ 2025-11-12 21:42 UTC (permalink / raw)
To: heiko
Cc: robh, krzk+dt, conor+dt, ukleinek, devicetree, linux-kernel,
linux-arm-kernel, linux-rockchip
The &cpu_thermal node was added at the wrong position, move it to
the correctly sorted one.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
.../boot/dts/rockchip/rk3568-qnap-ts433.dts | 96 +++++++++----------
1 file changed, 48 insertions(+), 48 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
index 6ae4316761c4..5656554ca284 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
@@ -196,6 +196,54 @@ &cpu3 {
cpu-supply = <&vdd_cpu>;
};
+/*
+ * The MCU can provide system temperature too, but only by polling and of
+ * course also cannot set trip points. So attach to the cpu thermal-zone
+ * instead to control the fan.
+ */
+&cpu_thermal {
+ trips {
+ case_fan0: case-fan0 {
+ hysteresis = <2000>;
+ temperature = <35000>;
+ type = "active";
+ };
+
+ case_fan1: case-fan1 {
+ hysteresis = <2000>;
+ temperature = <45000>;
+ type = "active";
+ };
+
+ case_fan2: case-fan2 {
+ hysteresis = <2000>;
+ temperature = <65000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ /*
+ * Always provide some air movement, due to small case
+ * full of harddrives.
+ */
+ map1 {
+ cooling-device = <&fan THERMAL_NO_LIMIT 1>;
+ trip = <&case_fan0>;
+ };
+
+ map2 {
+ cooling-device = <&fan 2 3>;
+ trip = <&case_fan1>;
+ };
+
+ map3 {
+ cooling-device = <&fan 4 THERMAL_NO_LIMIT>;
+ trip = <&case_fan2>;
+ };
+ };
+};
+
&gmac0 {
assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
@@ -492,54 +540,6 @@ rgmii_phy0: ethernet-phy@3 {
};
};
-/*
- * The MCU can provide system temperature too, but only by polling and of
- * course also cannot set trip points. So attach to the cpu thermal-zone
- * instead to control the fan.
- */
-&cpu_thermal {
- trips {
- case_fan0: case-fan0 {
- hysteresis = <2000>;
- temperature = <35000>;
- type = "active";
- };
-
- case_fan1: case-fan1 {
- hysteresis = <2000>;
- temperature = <45000>;
- type = "active";
- };
-
- case_fan2: case-fan2 {
- hysteresis = <2000>;
- temperature = <65000>;
- type = "active";
- };
- };
-
- cooling-maps {
- /*
- * Always provide some air movement, due to small case
- * full of harddrives.
- */
- map1 {
- cooling-device = <&fan THERMAL_NO_LIMIT 1>;
- trip = <&case_fan0>;
- };
-
- map2 {
- cooling-device = <&fan 2 3>;
- trip = <&case_fan1>;
- };
-
- map3 {
- cooling-device = <&fan 4 THERMAL_NO_LIMIT>;
- trip = <&case_fan2>;
- };
- };
-};
-
&pcie30phy {
data-lanes = <1 2>;
status = "okay";
--
2.47.2
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH v2 2/5] arm64: dts: rockchip: describe mcu eeprom cells on rk3568-ts433
2025-11-12 21:42 [PATCH v2 0/5] Some cleanups and addition of another Qnap TSx33 device Heiko Stuebner
2025-11-12 21:42 ` [PATCH v2 1/5] arm64: dts: rockchip: move cpu_thermal node to the correct position Heiko Stuebner
@ 2025-11-12 21:42 ` Heiko Stuebner
2025-11-12 21:42 ` [PATCH v2 3/5] arm64: dts: rockchip: move common qnap tsx33 parts to dtsi Heiko Stuebner
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Heiko Stuebner @ 2025-11-12 21:42 UTC (permalink / raw)
To: heiko
Cc: robh, krzk+dt, conor+dt, ukleinek, devicetree, linux-kernel,
linux-arm-kernel, linux-rockchip
The MCU's eeprom contains the unit's serial and a number of slots for
mac-addresses. As the MCU seems to be used in different devices, up to
8 mac addresses can live there and the unused slots are actually
initialized with empty mac-address strings like 00:00:00:00:05:09 .
Interestingly on the TS-433, the PCIe ethernet adapter brings its own
memory to hold its mac, and the gmac0 is supposed to get its mac from
the second mac-slot, while the first one stays empty.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
.../boot/dts/rockchip/rk3568-qnap-ts433.dts | 62 +++++++++++++++++++
1 file changed, 62 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
index 5656554ca284..224db87973b2 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
@@ -655,6 +655,68 @@ fan: fan-0 {
#cooling-cells = <2>;
cooling-levels = <0 64 89 128 166 204 221 238>;
};
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ serial-number@0 {
+ reg = <0x0 0x13>;
+ };
+
+ ext-port@22 {
+ reg = <0x22 0x2>;
+ };
+
+ mac0: mac@24 {
+ compatible = "mac-base";
+ reg = <0x24 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac1: mac@35 {
+ compatible = "mac-base";
+ reg = <0x35 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac2: mac@46 {
+ compatible = "mac-base";
+ reg = <0x46 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac3: mac@57 {
+ compatible = "mac-base";
+ reg = <0x57 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac4: mac@68 {
+ compatible = "mac-base";
+ reg = <0x68 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac5: mac@79 {
+ compatible = "mac-base";
+ reg = <0x79 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac6: mac@8a {
+ compatible = "mac-base";
+ reg = <0x8a 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac7: mac@9b {
+ compatible = "mac-base";
+ reg = <0x9b 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
};
};
--
2.47.2
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH v2 3/5] arm64: dts: rockchip: move common qnap tsx33 parts to dtsi
2025-11-12 21:42 [PATCH v2 0/5] Some cleanups and addition of another Qnap TSx33 device Heiko Stuebner
2025-11-12 21:42 ` [PATCH v2 1/5] arm64: dts: rockchip: move cpu_thermal node to the correct position Heiko Stuebner
2025-11-12 21:42 ` [PATCH v2 2/5] arm64: dts: rockchip: describe mcu eeprom cells on rk3568-ts433 Heiko Stuebner
@ 2025-11-12 21:42 ` Heiko Stuebner
2025-11-12 21:42 ` [PATCH v2 4/5] dt-bindings: arm: rockchip: add TS233 to RK3568-based QNAP NAS devices Heiko Stuebner
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Heiko Stuebner @ 2025-11-12 21:42 UTC (permalink / raw)
To: heiko
Cc: robh, krzk+dt, conor+dt, ukleinek, devicetree, linux-kernel,
linux-arm-kernel, linux-rockchip
The NAS series based around the rk3568 contains a number of models with
1-4 drives, that reuse most of the board structure.
Therefore move the shared parts to a dtsi, to be included by the devices.
As the smallest device is the 1-bay TS133, keep everything > slot1 in
the individual devicetree.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
.../boot/dts/rockchip/rk3568-qnap-ts433.dts | 666 +-----------------
.../boot/dts/rockchip/rk3568-qnap-tsx33.dtsi | 608 ++++++++++++++++
2 files changed, 645 insertions(+), 629 deletions(-)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-qnap-tsx33.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
index 224db87973b2..d1e3b7e7a280 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dts
@@ -6,10 +6,7 @@
/dts-v1/;
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "rk3568.dtsi"
+#include "rk3568-qnap-tsx33.dtsi"
/ {
model = "Qnap TS-433-4G NAS System 4-Bay";
@@ -17,83 +14,6 @@ / {
aliases {
ethernet0 = &gmac0;
- mmc0 = &sdhci;
- rtc0 = &rtc_rv8263;
- };
-
- chosen {
- stdout-path = "serial2:115200n8";
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <©_button_pin>, <&reset_button_pin>;
- pinctrl-names = "default";
-
- key-copy {
- label = "copy";
- gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_COPY>;
- };
-
- key-reset {
- label = "reset";
- gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-0 {
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_DISK;
- gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_LOW>;
- label = "hdd1:green:disk";
- linux,default-trigger = "disk-activity";
- pinctrl-names = "default";
- pinctrl-0 = <&hdd1_led_pin>;
- };
-
- led-1 {
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_DISK;
- gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
- label = "hdd2:green:disk";
- linux,default-trigger = "disk-activity";
- pinctrl-names = "default";
- pinctrl-0 = <&hdd2_led_pin>;
- };
-
- led-2 {
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_DISK;
- gpios = <&gpio1 RK_PD7 GPIO_ACTIVE_LOW>;
- label = "hdd3:green:disk";
- linux,default-trigger = "disk-activity";
- pinctrl-names = "default";
- pinctrl-0 = <&hdd3_led_pin>;
- };
-
- led-3 {
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_DISK;
- gpios = <&gpio2 RK_PA0 GPIO_ACTIVE_LOW>;
- label = "hdd4:green:disk";
- linux,default-trigger = "disk-activity";
- pinctrl-names = "default";
- pinctrl-0 = <&hdd4_led_pin>;
- };
- };
-
- dc_12v: regulator-dc-12v {
- compatible = "regulator-fixed";
- regulator-name = "dc_12v";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
};
vcc3v3_pcie: regulator-vcc3v3-pcie {
@@ -105,74 +25,6 @@ vcc3v3_pcie: regulator-vcc3v3-pcie {
gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
vin-supply = <&dc_12v>;
};
-
- vcc3v3_sys: regulator-vcc3v3-sys {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3_sys";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <&dc_12v>;
- };
-
- vcc5v0_host: regulator-vcc5v0-host {
- compatible = "regulator-fixed";
- enable-active-high;
- pinctrl-names = "default";
- pinctrl-0 = <&vcc5v0_host_en>;
- gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
- regulator-name = "vcc5v0_host";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <&vcc5v0_usb>;
- };
-
- vcc5v0_otg: regulator-vcc5v0-otg {
- compatible = "regulator-fixed";
- enable-active-high;
- gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&vcc5v0_otg_en>;
- regulator-name = "vcc5v0_otg";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <&vcc5v0_usb>;
- };
-
- vcc5v0_sys: regulator-vcc5v0-sys {
- compatible = "regulator-fixed";
- regulator-name = "vcc5v0_sys";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <&dc_12v>;
- };
-
- vcc5v0_usb: regulator-vcc5v0-usb {
- compatible = "regulator-fixed";
- regulator-name = "vcc5v0_usb";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <&dc_12v>;
- };
-};
-
-/* connected to usb_host0_xhci */
-&combphy0 {
- status = "okay";
-};
-
-/* connected to sata1 */
-&combphy1 {
- status = "okay";
};
/* connected to sata2 */
@@ -180,70 +32,6 @@ &combphy2 {
status = "okay";
};
-&cpu0 {
- cpu-supply = <&vdd_cpu>;
-};
-
-&cpu1 {
- cpu-supply = <&vdd_cpu>;
-};
-
-&cpu2 {
- cpu-supply = <&vdd_cpu>;
-};
-
-&cpu3 {
- cpu-supply = <&vdd_cpu>;
-};
-
-/*
- * The MCU can provide system temperature too, but only by polling and of
- * course also cannot set trip points. So attach to the cpu thermal-zone
- * instead to control the fan.
- */
-&cpu_thermal {
- trips {
- case_fan0: case-fan0 {
- hysteresis = <2000>;
- temperature = <35000>;
- type = "active";
- };
-
- case_fan1: case-fan1 {
- hysteresis = <2000>;
- temperature = <45000>;
- type = "active";
- };
-
- case_fan2: case-fan2 {
- hysteresis = <2000>;
- temperature = <65000>;
- type = "active";
- };
- };
-
- cooling-maps {
- /*
- * Always provide some air movement, due to small case
- * full of harddrives.
- */
- map1 {
- cooling-device = <&fan THERMAL_NO_LIMIT 1>;
- trip = <&case_fan0>;
- };
-
- map2 {
- cooling-device = <&fan 2 3>;
- trip = <&case_fan1>;
- };
-
- map3 {
- cooling-device = <&fan 4 THERMAL_NO_LIMIT>;
- trip = <&case_fan2>;
- };
- };
-};
-
&gmac0 {
assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
@@ -260,263 +48,7 @@ &gmac0_rgmii_clk
status = "okay";
};
-&gpu {
- mali-supply = <&vdd_gpu>;
- status = "okay";
-};
-
-&i2c0 {
- status = "okay";
-
- pmic@20 {
- compatible = "rockchip,rk809";
- reg = <0x20>;
- interrupt-parent = <&gpio0>;
- interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
- #clock-cells = <1>;
- pinctrl-names = "default";
- pinctrl-0 = <&pmic_int_l>;
- system-power-controller;
- vcc1-supply = <&vcc3v3_sys>;
- vcc2-supply = <&vcc3v3_sys>;
- vcc3-supply = <&vcc3v3_sys>;
- vcc4-supply = <&vcc3v3_sys>;
- vcc5-supply = <&vcc3v3_sys>;
- vcc6-supply = <&vcc3v3_sys>;
- vcc7-supply = <&vcc3v3_sys>;
- vcc8-supply = <&vcc3v3_sys>;
- vcc9-supply = <&vcc3v3_sys>;
- wakeup-source;
-
- regulators {
- vdd_logic: DCDC_REG1 {
- regulator-name = "vdd_logic";
- regulator-always-on;
- regulator-boot-on;
- regulator-initial-mode = <0x2>;
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1350000>;
- regulator-ramp-delay = <6001>;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vdd_gpu: DCDC_REG2 {
- regulator-name = "vdd_gpu";
- regulator-always-on;
- regulator-initial-mode = <0x2>;
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1350000>;
- regulator-ramp-delay = <6001>;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vcc_ddr: DCDC_REG3 {
- regulator-name = "vcc_ddr";
- regulator-always-on;
- regulator-boot-on;
- regulator-initial-mode = <0x2>;
-
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- vdd_npu: DCDC_REG4 {
- regulator-name = "vdd_npu";
- regulator-initial-mode = <0x2>;
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <1350000>;
- regulator-ramp-delay = <6001>;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vcc_1v8: DCDC_REG5 {
- regulator-name = "vcc_1v8";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vdda0v9_image: LDO_REG1 {
- regulator-name = "vdda0v9_image";
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <900000>;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vdda_0v9: LDO_REG2 {
- regulator-name = "vdda_0v9";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <900000>;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vdda0v9_pmu: LDO_REG3 {
- regulator-name = "vdda0v9_pmu";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <900000>;
-
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <900000>;
- };
- };
-
- vccio_acodec: LDO_REG4 {
- regulator-name = "vccio_acodec";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vccio_sd: LDO_REG5 {
- regulator-name = "vccio_sd";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vcc3v3_pmu: LDO_REG6 {
- regulator-name = "vcc3v3_pmu";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <3300000>;
- };
- };
-
- vcca_1v8: LDO_REG7 {
- regulator-name = "vcca_1v8";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vcca1v8_pmu: LDO_REG8 {
- regulator-name = "vcca1v8_pmu";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <1800000>;
- };
- };
-
- vcca1v8_image: LDO_REG9 {
- regulator-name = "vcca1v8_image";
- regulator-always-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vcc_3v3: SWITCH_REG1 {
- regulator-name = "vcc_3v3";
- regulator-always-on;
- regulator-boot-on;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vcc3v3_sd: SWITCH_REG2 {
- regulator-name = "vcc3v3_sd";
- /*
- * turning this off, breaks access to both
- * PCIe controllers, refclk generator perhaps
- */
- regulator-always-on;
- regulator-boot-on;
-
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
- };
- };
-
- vdd_cpu: regulator@40 {
- compatible = "silergy,syr827";
- reg = <0x40>;
- fcs,suspend-voltage-selector = <1>;
- regulator-name = "vdd_cpu";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <712500>;
- regulator-max-microvolt = <1390000>;
- regulator-ramp-delay = <2300>;
- vin-supply = <&vcc5v0_sys>;
- };
-};
-
&i2c1 {
- status = "okay";
-
- rtc_rv8263: rtc@51 {
- compatible = "microcrystal,rv8263";
- reg = <0x51>;
- wakeup-source;
- };
-
- /* eeprom for vital-product-data on the mainboard */
- eeprom@54 {
- compatible = "giantec,gt24c04a", "atmel,24c04";
- reg = <0x54>;
- label = "VPD_MB";
- num-addresses = <2>;
- pagesize = <16>;
- read-only;
- };
-
/* eeprom for vital-product-data on the backplane */
eeprom@56 {
compatible = "giantec,gt24c04a", "atmel,24c04";
@@ -528,6 +60,42 @@ eeprom@56 {
};
};
+&leds {
+ led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_DISK;
+ gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
+ label = "hdd2:green:disk";
+ linux,default-trigger = "disk-activity";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdd2_led_pin>;
+ };
+
+ led-2 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_DISK;
+ gpios = <&gpio1 RK_PD7 GPIO_ACTIVE_LOW>;
+ label = "hdd3:green:disk";
+ linux,default-trigger = "disk-activity";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdd3_led_pin>;
+ };
+
+ led-3 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_DISK;
+ gpios = <&gpio2 RK_PA0 GPIO_ACTIVE_LOW>;
+ label = "hdd4:green:disk";
+ linux,default-trigger = "disk-activity";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdd4_led_pin>;
+ };
+};
+
+&mcu {
+ compatible = "qnap,ts433-mcu";
+};
+
&mdio0 {
rgmii_phy0: ethernet-phy@3 {
/* Motorcomm YT8521 phy */
@@ -567,21 +135,7 @@ eth_phy0_reset_pin: eth-phy0-reset-pin {
};
};
- keys {
- copy_button_pin: copy-button-pin {
- rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>;
- };
-
- reset_button_pin: reset-button-pin {
- rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
- };
- };
-
leds {
- hdd1_led_pin: hdd1-led-pin {
- rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
- };
-
hdd2_led_pin: hdd2-led-pin {
rockchip,pins = <1 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
};
@@ -594,152 +148,12 @@ hdd4_led_pin: hdd4_led-pin {
rockchip,pins = <2 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
-
- pmic {
- pmic_int_l: pmic-int-l {
- rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
- };
- };
-
- usb {
- vcc5v0_host_en: vcc5v0-host-en {
- rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
- };
-
- vcc5v0_otg_en: vcc5v0-otg-en {
- rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
- };
- };
-};
-
-&pmu_io_domains {
- vccio4-supply = <&vcc_1v8>;
- vccio6-supply = <&vcc_1v8>;
- status = "okay";
-};
-
-&sata1 {
- status = "okay";
};
&sata2 {
status = "okay";
};
-&sdhci {
- bus-width = <8>;
- max-frequency = <200000000>;
- non-removable;
- pinctrl-names = "default";
- pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
- status = "okay";
-};
-
-&tsadc {
- rockchip,hw-tshut-mode = <1>;
- rockchip,hw-tshut-polarity = <0>;
- status = "okay";
-};
-
-/*
- * Connected to an MCU, that provides access to more LEDs,
- * buzzer, fan control and more.
- */
-&uart0 {
- status = "okay";
-
- mcu {
- compatible = "qnap,ts433-mcu";
-
- fan: fan-0 {
- #cooling-cells = <2>;
- cooling-levels = <0 64 89 128 166 204 221 238>;
- };
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- serial-number@0 {
- reg = <0x0 0x13>;
- };
-
- ext-port@22 {
- reg = <0x22 0x2>;
- };
-
- mac0: mac@24 {
- compatible = "mac-base";
- reg = <0x24 0x11>;
- #nvmem-cell-cells = <1>;
- };
-
- mac1: mac@35 {
- compatible = "mac-base";
- reg = <0x35 0x11>;
- #nvmem-cell-cells = <1>;
- };
-
- mac2: mac@46 {
- compatible = "mac-base";
- reg = <0x46 0x11>;
- #nvmem-cell-cells = <1>;
- };
-
- mac3: mac@57 {
- compatible = "mac-base";
- reg = <0x57 0x11>;
- #nvmem-cell-cells = <1>;
- };
-
- mac4: mac@68 {
- compatible = "mac-base";
- reg = <0x68 0x11>;
- #nvmem-cell-cells = <1>;
- };
-
- mac5: mac@79 {
- compatible = "mac-base";
- reg = <0x79 0x11>;
- #nvmem-cell-cells = <1>;
- };
-
- mac6: mac@8a {
- compatible = "mac-base";
- reg = <0x8a 0x11>;
- #nvmem-cell-cells = <1>;
- };
-
- mac7: mac@9b {
- compatible = "mac-base";
- reg = <0x9b 0x11>;
- #nvmem-cell-cells = <1>;
- };
- };
- };
-};
-
-/*
- * Pins available on CN3 connector at TTL voltage level (3V3).
- * ,_ _.
- * |1234| 1=TX 2=VCC
- * `----' 3=RX 4=GND
- */
-&uart2 {
- status = "okay";
-};
-
-&usb2phy0 {
- status = "okay";
-};
-
-/* connected to usb_host0_xhci */
-&usb2phy0_otg {
- phy-supply = <&vcc5v0_otg>;
- status = "okay";
-};
-
&usb2phy1 {
status = "okay";
};
@@ -765,12 +179,6 @@ &usb_host0_ohci {
status = "okay";
};
-/* front port */
-&usb_host0_xhci {
- dr_mode = "host";
- status = "okay";
-};
-
/* left port backside */
&usb_host1_ehci {
status = "okay";
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-qnap-tsx33.dtsi b/arch/arm64/boot/dts/rockchip/rk3568-qnap-tsx33.dtsi
new file mode 100644
index 000000000000..f009275c72c8
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-qnap-tsx33.dtsi
@@ -0,0 +1,608 @@
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "rk3568.dtsi"
+
+/ {
+ aliases {
+ mmc0 = &sdhci;
+ rtc0 = &rtc_rv8263;
+ };
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <©_button_pin>, <&reset_button_pin>;
+ pinctrl-names = "default";
+
+ key-copy {
+ label = "copy";
+ gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_COPY>;
+ };
+
+ key-reset {
+ label = "reset";
+ gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_DISK;
+ gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_LOW>;
+ label = "hdd1:green:disk";
+ linux,default-trigger = "disk-activity";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdd1_led_pin>;
+ };
+ };
+
+ dc_12v: regulator-dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc3v3_sys: regulator-vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc5v0_host: regulator-vcc5v0-host {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host_en>;
+ gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ regulator-name = "vcc5v0_host";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_usb>;
+ };
+
+ vcc5v0_otg: regulator-vcc5v0-otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_otg_en>;
+ regulator-name = "vcc5v0_otg";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_usb>;
+ };
+
+ vcc5v0_sys: regulator-vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc5v0_usb: regulator-vcc5v0-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+};
+
+/* connected to usb_host0_xhci */
+&combphy0 {
+ status = "okay";
+};
+
+/* connected to sata1 */
+&combphy1 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+/*
+ * The MCU can provide system temperature too, but only by polling and of
+ * course also cannot set trip points. So attach to the cpu thermal-zone
+ * instead to control the fan.
+ */
+&cpu_thermal {
+ trips {
+ case_fan0: case-fan0 {
+ hysteresis = <2000>;
+ temperature = <35000>;
+ type = "active";
+ };
+
+ case_fan1: case-fan1 {
+ hysteresis = <2000>;
+ temperature = <45000>;
+ type = "active";
+ };
+
+ case_fan2: case-fan2 {
+ hysteresis = <2000>;
+ temperature = <65000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ /*
+ * Always provide some air movement, due to small case
+ * full of harddrives.
+ */
+ map1 {
+ cooling-device = <&fan THERMAL_NO_LIMIT 1>;
+ trip = <&case_fan0>;
+ };
+
+ map2 {
+ cooling-device = <&fan 2 3>;
+ trip = <&case_fan1>;
+ };
+
+ map3 {
+ cooling-device = <&fan 4 THERMAL_NO_LIMIT>;
+ trip = <&case_fan2>;
+ };
+ };
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ system-power-controller;
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+ wakeup-source;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ /*
+ * turning this off, breaks access to both
+ * PCIe controllers, refclk generator perhaps
+ */
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+
+ vdd_cpu: regulator@40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1390000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ rtc_rv8263: rtc@51 {
+ compatible = "microcrystal,rv8263";
+ reg = <0x51>;
+ wakeup-source;
+ };
+
+ /* eeprom for vital-product-data on the mainboard */
+ eeprom@54 {
+ compatible = "giantec,gt24c04a", "atmel,24c04";
+ reg = <0x54>;
+ label = "VPD_MB";
+ num-addresses = <2>;
+ pagesize = <16>;
+ read-only;
+ };
+};
+
+&pinctrl {
+ keys {
+ copy_button_pin: copy-button-pin {
+ rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ reset_button_pin: reset-button-pin {
+ rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ hdd1_led_pin: hdd1-led-pin {
+ rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb {
+ vcc5v0_host_en: vcc5v0-host-en {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc5v0_otg_en: vcc5v0-otg-en {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ vccio4-supply = <&vcc_1v8>;
+ vccio6-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sata1 {
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+/*
+ * Connected to an MCU, that provides access to more LEDs,
+ * buzzer, fan control and more.
+ */
+&uart0 {
+ status = "okay";
+
+ mcu: mcu {
+ fan: fan-0 {
+ #cooling-cells = <2>;
+ cooling-levels = <0 64 89 128 166 204 221 238>;
+ };
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ serial-number@0 {
+ reg = <0x0 0x13>;
+ };
+
+ ext-port@22 {
+ reg = <0x22 0x2>;
+ };
+
+ mac0: mac@24 {
+ compatible = "mac-base";
+ reg = <0x24 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac1: mac@35 {
+ compatible = "mac-base";
+ reg = <0x35 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac2: mac@46 {
+ compatible = "mac-base";
+ reg = <0x46 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac3: mac@57 {
+ compatible = "mac-base";
+ reg = <0x57 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac4: mac@68 {
+ compatible = "mac-base";
+ reg = <0x68 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac5: mac@79 {
+ compatible = "mac-base";
+ reg = <0x79 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac6: mac@8a {
+ compatible = "mac-base";
+ reg = <0x8a 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac7: mac@9b {
+ compatible = "mac-base";
+ reg = <0x9b 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+};
+
+/*
+ * Pins available on CN3 connector at TTL voltage level (3V3).
+ * ,_ _.
+ * |1234| 1=TX 2=VCC
+ * `----' 3=RX 4=GND
+ */
+&uart2 {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+/* connected to usb_host0_xhci */
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_otg>;
+ status = "okay";
+};
+
+/* front port */
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
--
2.47.2
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH v2 4/5] dt-bindings: arm: rockchip: add TS233 to RK3568-based QNAP NAS devices
2025-11-12 21:42 [PATCH v2 0/5] Some cleanups and addition of another Qnap TSx33 device Heiko Stuebner
` (2 preceding siblings ...)
2025-11-12 21:42 ` [PATCH v2 3/5] arm64: dts: rockchip: move common qnap tsx33 parts to dtsi Heiko Stuebner
@ 2025-11-12 21:42 ` Heiko Stuebner
2025-11-12 21:42 ` [PATCH v2 5/5] arm64: dts: rockchip: add QNAP TS233 devicetree Heiko Stuebner
2025-11-20 22:22 ` [PATCH v2 0/5] Some cleanups and addition of another Qnap TSx33 device Heiko Stuebner
5 siblings, 0 replies; 7+ messages in thread
From: Heiko Stuebner @ 2025-11-12 21:42 UTC (permalink / raw)
To: heiko
Cc: robh, krzk+dt, conor+dt, ukleinek, devicetree, linux-kernel,
linux-arm-kernel, linux-rockchip, Conor Dooley
QNAP builds a number of variants of the RK3568-based NAS design.
Add the 2-bay TS233 variant.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 6aceaa8acbb2..790f910aa38b 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -868,9 +868,11 @@ properties:
- const: prt,mecsbc
- const: rockchip,rk3568
- - description: QNAP TS-433-4G 4-Bay NAS
+ - description: QNAP TS-x33 NAS devices
items:
- - const: qnap,ts433
+ - enum:
+ - qnap,ts233
+ - qnap,ts433
- const: rockchip,rk3568
- description: Radxa Compute Module 3 (CM3)
--
2.47.2
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH v2 5/5] arm64: dts: rockchip: add QNAP TS233 devicetree
2025-11-12 21:42 [PATCH v2 0/5] Some cleanups and addition of another Qnap TSx33 device Heiko Stuebner
` (3 preceding siblings ...)
2025-11-12 21:42 ` [PATCH v2 4/5] dt-bindings: arm: rockchip: add TS233 to RK3568-based QNAP NAS devices Heiko Stuebner
@ 2025-11-12 21:42 ` Heiko Stuebner
2025-11-20 22:22 ` [PATCH v2 0/5] Some cleanups and addition of another Qnap TSx33 device Heiko Stuebner
5 siblings, 0 replies; 7+ messages in thread
From: Heiko Stuebner @ 2025-11-12 21:42 UTC (permalink / raw)
To: heiko
Cc: robh, krzk+dt, conor+dt, ukleinek, devicetree, linux-kernel,
linux-arm-kernel, linux-rockchip
The TS233 is a 2 bay NAS similar to the TS433. Architecture-wise it really
seems to be the same minus the additional PCIe connected components the
TS433 has.
So it just uses two of the SoCs SATA ports and the SoC's gigabit ethernet.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3568-qnap-ts233.dts | 131 ++++++++++++++++++
2 files changed, 132 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-qnap-ts233.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ad684e3831bc..d1d384df00b7 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -142,6 +142,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5s.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-photonicat.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts233.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts433.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts233.dts b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts233.dts
new file mode 100644
index 000000000000..f16d1c628793
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts233.dts
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2024 Heiko Stuebner <heiko@sntech.de>
+ */
+
+/dts-v1/;
+
+#include "rk3568-qnap-tsx33.dtsi"
+
+/ {
+ model = "Qnap TS-233-2G NAS System 2-Bay";
+ compatible = "qnap,ts233", "rockchip,rk3568";
+
+ aliases {
+ ethernet0 = &gmac0;
+ };
+};
+
+/* connected to sata2 */
+&combphy2 {
+ status = "okay";
+};
+
+&gmac0 {
+ assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+ assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
+ assigned-clock-rates = <0>, <125000000>;
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy0>;
+ phy-mode = "rgmii-id";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_miim
+ &gmac0_tx_bus2
+ &gmac0_rx_bus2
+ &gmac0_rgmii_clk
+ &gmac0_rgmii_bus>;
+ status = "okay";
+};
+
+&i2c1 {
+ /* eeprom for vital-product-data on the backplane */
+ eeprom@56 {
+ compatible = "giantec,gt24c04a", "atmel,24c04";
+ reg = <0x56>;
+ label = "VPD_BP";
+ num-addresses = <2>;
+ pagesize = <16>;
+ read-only;
+ };
+};
+
+&leds {
+ led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_DISK;
+ gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
+ label = "hdd2:green:disk";
+ linux,default-trigger = "disk-activity";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdd2_led_pin>;
+ };
+};
+
+&mcu {
+ compatible = "qnap,ts233-mcu";
+};
+
+&mdio0 {
+ rgmii_phy0: ethernet-phy@3 {
+ /* Motorcomm YT8521 phy */
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x3>;
+ pinctrl-0 = <ð_phy0_reset_pin>;
+ pinctrl-names = "default";
+ reset-assert-us = <10000>;
+ reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pinctrl {
+ gmac0 {
+ eth_phy0_reset_pin: eth-phy0-reset-pin {
+ rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ hdd2_led_pin: hdd2-led-pin {
+ rockchip,pins = <1 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&sata2 {
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+/* connected to usb_host1_ehci/ohci */
+&usb2phy1_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+/* connected to usb_host0_ehci/ohci */
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+/* right port backside */
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+/* left port backside */
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
--
2.47.2
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: [PATCH v2 0/5] Some cleanups and addition of another Qnap TSx33 device
2025-11-12 21:42 [PATCH v2 0/5] Some cleanups and addition of another Qnap TSx33 device Heiko Stuebner
` (4 preceding siblings ...)
2025-11-12 21:42 ` [PATCH v2 5/5] arm64: dts: rockchip: add QNAP TS233 devicetree Heiko Stuebner
@ 2025-11-20 22:22 ` Heiko Stuebner
5 siblings, 0 replies; 7+ messages in thread
From: Heiko Stuebner @ 2025-11-20 22:22 UTC (permalink / raw)
To: Heiko Stuebner
Cc: robh, krzk+dt, conor+dt, ukleinek, devicetree, linux-kernel,
linux-arm-kernel, linux-rockchip
On Wed, 12 Nov 2025 22:42:01 +0100, Heiko Stuebner wrote:
> This fixes the 2nd network adapter on the TS433 and adds the TS233
> a 2-bay device being otherwise similar to the TS433.
>
> changes in v2:
> - add Conor's Ack on the TS233 binding
> - drop TS433 ethernet-delay patch, as that was unneeded and resulted
> from me doing wonky stuff during testing and are completely useless
> - drop tx/rx-delays from new TS233 dts as well
>
> [...]
Applied, thanks!
[1/5] arm64: dts: rockchip: move cpu_thermal node to the correct position
commit: 15efa2414602ad4c411ea8d4113b87656ebe0737
[2/5] arm64: dts: rockchip: describe mcu eeprom cells on rk3568-ts433
commit: 81f116991433d2547d7f350873cb4511ebcd4fec
[3/5] arm64: dts: rockchip: move common qnap tsx33 parts to dtsi
commit: 35202606ea08b9ec2b1386ac937a729e25d5beb0
[4/5] dt-bindings: arm: rockchip: add TS233 to RK3568-based QNAP NAS devices
commit: a576b51e13870ba957e13e6cc265431260a32a77
[5/5] arm64: dts: rockchip: add QNAP TS233 devicetree
commit: ce0b84e766ad7b2ec5d2ac7840675f223640f3e3
Best regards,
--
Heiko Stuebner <heiko@sntech.de>
^ permalink raw reply [flat|nested] 7+ messages in thread