[PATCH 0/2] Add support for Zhunyi Z40046 LCD panel

[PATCH 0/2] Add support for Zhunyi Z40046 LCD panel

[Luca Leonardo Scorcia]

The Zhunyi Z40046 is a 480x800 24-bit WVGA DSI panel based on the
Fitipower JD9161Z DSI controller found in the Xiaomi Mi Smart Clock
x04g, apparently in two different variants.

The Fitipower JD9161Z LCD driver IC is very similar to the Jadard
JD9365DA-H3, it just uses different initialization sequences. A
partial data sheet is available at [1].

The two initialization sequences for the panel have been extracted from
Android original firmware for the Xiaomi Smart Clock.

Variant v1 tested on device. Variant v2 not tested.

[1] https://github.com/QuecPython/QuecPython_lib_bundles/blob/master/libraries/LCD/JD91651z/JD9161Z_DS_Preliminary_V0.01_20180803(1).pdf

Luca Leonardo Scorcia (2):
  dt-bindings: display: panel: Add compatibles for Zhunyi Z40046
  drm/panel: jd9365da: Support for Zhunyi Z40046 panels

 .../display/panel/jadard,jd9365da-h3.yaml     |   2 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 .../gpu/drm/panel/panel-jadard-jd9365da-h3.c  | 308 ++++++++++++++++++
 3 files changed, 312 insertions(+)

-- 
2.43.0

[PATCH 1/2] dt-bindings: display: panel: Add compatibles for Zhunyi Z40046

[Luca Leonardo Scorcia]

The Zhunyi Z40046 is a 480x800 24-bit WVGA DSI panel based on the
Fitipower JD9161Z DSI controller found in the Xiaomi Mi Smart Clock
x04g, apparently in two different variants.

The Fitipower JD9161Z LCD driver IC is very similar to the Jadard
JD9365DA-H3, it just uses a different initialization sequence.

Since this is the first supported device from this vendor, document its
name to the vendor-prefixes.yaml file as well.

Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
---
 .../devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml   | 2 ++
 Documentation/devicetree/bindings/vendor-prefixes.yaml          | 2 ++
 2 files changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml b/Documentation/devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml
index 5802fb3c9ffe..da17072ffaaa 100644
--- a/Documentation/devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml
+++ b/Documentation/devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml
@@ -23,6 +23,8 @@ properties:
           - melfas,lmfbx101117480
           - radxa,display-10hd-ad001
           - radxa,display-8hd-ad002
+          - zhunyi,z40046v1
+          - zhunyi,z40046v2
       - const: jadard,jd9365da-h3
 
   reg:
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index ee7fd3cfe203..18121440dc22 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1913,6 +1913,8 @@ patternProperties:
     description: Shenzhen Zkmagic Technology Co., Ltd.
   "^zte,.*":
     description: ZTE Corp.
+  "^zhunyi,.*":
+    description: Shenzhen Zhunyi Technology Co., Ltd.
   "^zyxel,.*":
     description: ZyXEL Communications Corp.
 
-- 
2.43.0

[PATCH 2/2] drm/panel: jd9365da: Support for Zhunyi Z40046 panels

[Luca Leonardo Scorcia]

The Zhunyi Z40046 is a 480x800 24-bit WVGA DSI panel based on the
Fitipower JD9161Z DSI controller found in the Xiaomi Mi Smart Clock
x04g, apparently in two different variants.

The Fitipower JD9161Z LCD driver IC is very similar to the Jadard
JD9365DA-H3, it just uses different initialization sequences.

The two initialization sequences for the panel have been extracted from
Android original firmware for the Xiaomi Smart Clock.

Variant v1 tested on device. Variant v2 not tested.

Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
---
 .../gpu/drm/panel/panel-jadard-jd9365da-h3.c  | 308 ++++++++++++++++++
 1 file changed, 308 insertions(+)

diff --git a/drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c b/drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c
index 5386a06fcd08..9bcf846684e4 100644
--- a/drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c
+++ b/drivers/gpu/drm/panel/panel-jadard-jd9365da-h3.c
@@ -46,11 +46,22 @@ struct jadard {
 	struct gpio_desc *reset;
 };
 
+#define JD9161Z_DCS_SWITCH_PAGE		0xde
+
+#define jd9161z_switch_page(dsi_ctx, page) \
+	mipi_dsi_dcs_write_seq_multi(dsi_ctx, JD9161Z_DCS_SWITCH_PAGE, (page))
+
 #define JD9365DA_DCS_SWITCH_PAGE	0xe0
 
 #define jd9365da_switch_page(dsi_ctx, page) \
 	mipi_dsi_dcs_write_seq_multi(dsi_ctx, JD9365DA_DCS_SWITCH_PAGE, (page))
 
+static void jd9161z_enable_standard_cmds(struct mipi_dsi_multi_context *dsi_ctx)
+{
+	// Enable access to DCS and internal commands
+	mipi_dsi_dcs_write_seq_multi(dsi_ctx, 0xdf, 0x91, 0x62, 0xf3);
+}
+
 static void jadard_enable_standard_cmds(struct mipi_dsi_multi_context *dsi_ctx)
 {
 	mipi_dsi_dcs_write_seq_multi(dsi_ctx, 0xe1, 0x93);
@@ -1366,6 +1377,295 @@ static const struct jadard_panel_desc anbernic_rgds_display_desc = {
 		      MIPI_DSI_CLOCK_NON_CONTINUOUS | MIPI_DSI_MODE_LPM,
 };
 
+// Sequence retrieved from Xiaomi Mi Smart Clock x04g kernel in boot.bin
+static int zhunyi_z40046_init_cmds_v1(struct jadard *jadard_data)
+{
+	struct mipi_dsi_multi_context dsi_ctx = { .dsi = jadard_data->dsi };
+
+	// Init configuration sequence
+	jd9161z_switch_page(&dsi_ctx, 0x00);
+	jd9161z_enable_standard_cmds(&dsi_ctx);
+
+	// GAMMA_SET (pos/neg voltage of gamma power)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xb7,
+		0x10, 0x04, 0x86, 0x00, 0x1b, 0x35);
+
+	// DCDC_SEL (power mode and charge pump settings)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xbb,
+		0x69, 0x0b, 0x30, 0xb2, 0xb2, 0xc0, 0xe0, 0x20,
+		0xf0, 0x50, 0x60,
+	);
+
+	// VDDD_CTRL (control logic voltage setting)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xbc,
+		0x73, 0x14);
+
+	// SETRGBCYC (display waveform cycle of RGB mode)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc3,
+		0x74, 0x04, 0x08, 0x0e, 0x00, 0x0e, 0x0c, 0x08,
+		0x0e, 0x00, 0x0e, 0x82, 0x0a, 0x82,
+	);
+
+	// SET_TCON (timing control setting)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc4,
+		0x10, 0x90, 0x92, 0x0e, 0x0b, 0x04);
+
+	// SET_R_GAMMA (set red gamma output voltage)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc8,
+		0x7e, 0x76, 0x68, 0x57, 0x4c, 0x39, 0x3a, 0x23,
+		0x3d, 0x3d, 0x40, 0x61, 0x54, 0x64, 0x5d, 0x62,
+		0x5a, 0x50, 0x32, 0x7e, 0x76, 0x68, 0x57, 0x4c,
+		0x39, 0x3a, 0x23, 0x3d, 0x3d, 0x40, 0x61, 0x54,
+		0x64, 0x5d, 0x62, 0x5a, 0x50, 0x32,
+	);
+
+	// SET_GIP_L (CGOUTx_L signal mapping, gs_panel = 0)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd0,
+		0x1f, 0x0a, 0x08, 0x06, 0x04, 0x1f, 0x00, 0x1f,
+		0x17, 0x1f, 0x18, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f,
+	);
+
+	// SET_GIP_R (CGOUTx_R signal mapping, gs_panel = 0)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd1,
+		0x1f, 0x0b, 0x09, 0x07, 0x05, 0x1f, 0x01, 0x1f,
+		0x17, 0x1f, 0x18, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f,
+	);
+
+	// SETGIP1 (GIP signal timing 1)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd4,
+		0x10, 0x00, 0x00, 0x03, 0x60, 0x05, 0x10, 0x00,
+		0x02, 0x06, 0x68, 0x00, 0x6c, 0x00, 0x00, 0x00,
+		0x00, 0x06, 0x78, 0x71, 0x07, 0x06, 0x68, 0x0c,
+		0x25, 0x00, 0x63, 0x03, 0x00,
+	);
+
+	// SETGIP2 (GIP signal timing 1)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd5,
+		0x20, 0x10, 0x8c, 0x18, 0x00, 0x80, 0x00, 0x08,
+		0x00, 0x00, 0x06, 0x60, 0x00, 0x81, 0x70, 0x02,
+		0x30, 0x01, 0x00, 0x00, 0xc0, 0x00, 0x00, 0x00,
+		0x03, 0x60, 0x83, 0x90, 0x00, 0x00, 0x03, 0x4f,
+		0x03, 0x00, 0x1f, 0x3f, 0x00, 0x00, 0x00, 0x00,
+	);
+
+	jd9161z_switch_page(&dsi_ctx, 0x04);
+
+	// ?
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xb0,
+		0x24, 0x01);
+
+	jd9161z_switch_page(&dsi_ctx, 0x02);
+
+	// SETRGBCYC2 (RGB IF source switch control timing)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc1,
+		0x71);
+
+	// ?
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc2,
+		0x00, 0x18, 0x08, 0x1e, 0x25, 0x7c, 0xc7,
+	);
+
+	jd9161z_switch_page(&dsi_ctx, 0x00);
+
+	mipi_dsi_dcs_set_tear_on_multi(&dsi_ctx, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
+
+	mipi_dsi_msleep(&dsi_ctx, 120);
+
+	mipi_dsi_dcs_exit_sleep_mode_multi(&dsi_ctx);
+
+	mipi_dsi_msleep(&dsi_ctx, 120);
+
+	mipi_dsi_dcs_set_display_on_multi(&dsi_ctx);
+
+	mipi_dsi_msleep(&dsi_ctx, 5);
+
+	return dsi_ctx.accum_err;
+};
+
+static const struct jadard_panel_desc zhunyi_z40046v1_desc = {
+	.mode = {
+		.clock		= 26700,
+
+		.hdisplay	= 480,
+		.hsync_start	= 480 + 20,
+		.hsync_end	= 480 + 20 + 20,
+		.htotal		= 480 + 20 + 20 + 20,
+
+		.vdisplay	= 800,
+		.vsync_start	= 800 + 12,
+		.vsync_end	= 800 + 12 + 4,
+		.vtotal		= 800 + 12 + 4 + 8,
+
+		.width_mm	= 52,
+		.height_mm	= 86,
+		.flags		= DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+		.type		= DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+	},
+	.lanes = 2,
+	.format = MIPI_DSI_FMT_RGB888,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
+		MIPI_DSI_MODE_LPM,
+	.lp11_before_reset = true,
+	.reset_before_power_off_vcioo = true,
+	.vcioo_to_lp11_delay_ms = 5,
+	.lp11_to_reset_delay_ms = 10,
+	.backlight_off_to_display_off_delay_ms = 100,
+	.display_off_to_enter_sleep_delay_ms = 50,
+	.enter_sleep_to_reset_down_delay_ms = 100,
+	.init = zhunyi_z40046_init_cmds_v1,
+};
+
+// Sequence retrieved from Xiaomi Mi Smart Clock x04g kernel in boot.bin
+static int zhunyi_z40046_init_cmds_v2(struct jadard *jadard_data)
+{
+	struct mipi_dsi_multi_context dsi_ctx = { .dsi = jadard_data->dsi };
+
+	// Init configuration sequence
+	jd9161z_switch_page(&dsi_ctx, 0x00);
+	jd9161z_enable_standard_cmds(&dsi_ctx);
+
+	// GAMMA_SET (pos/neg voltage of gamma power)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xb7,
+		0x10, 0x08, 0x42, 0x00, 0x56, 0x42,
+	);
+
+	// DCDC_SEL (power mode and charge pump settings)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xbb,
+		0x52, 0x0f, 0xb2, 0xb2, 0xb2, 0xc0, 0xd0, 0x50,
+		0xf0, 0x40, 0x50,
+	);
+
+	// VDDD_CTRL (control logic voltage setting)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xbc,
+		0x73, 0x14);
+
+	// SETRGBCYC (display waveform cycle of RGB mode)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc3,
+		0x04, 0x07, 0x0b, 0x17, 0x00, 0x17, 0x04, 0x17,
+		0x17, 0x00, 0x17, 0x82, 0x0b, 0x82,
+	);
+
+	// SET_TCON (timing control setting)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc4,
+		0x10, 0x90, 0x92, 0x0e, 0x06,
+	);
+
+	// SET_R_GAMMA (set red gamma output voltage)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc8,
+		0x7f, 0x78, 0x69, 0x56, 0x47, 0x33, 0x34, 0x1e,
+		0x3b, 0x3e, 0x43, 0x67, 0x5d, 0x6f, 0x68, 0x70,
+		0x6a, 0x61, 0x3c, 0x7f, 0x78, 0x69, 0x56, 0x47,
+		0x33, 0x34, 0x1e, 0x3b, 0x3e, 0x43, 0x67, 0x5d,
+		0x6f, 0x68, 0x70, 0x6a, 0x61, 0x3c,
+	);
+
+	// SET_GIP_L (CGOUTx_L signal mapping, gs_panel = 0)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd0,
+		0x1f, 0x1e, 0x07, 0x05, 0x01, 0x1f, 0x1f, 0x1f,
+		0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f,
+	);
+
+	// SET_GIP_R (CGOUTx_R signal mapping, gs_panel = 0)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd1,
+		0x1f, 0x1e, 0x06, 0x04, 0x00, 0x1f, 0x1f, 0x1f,
+		0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f,
+	);
+
+	// SET_GIP_L_GS (CGOUTx_L signal mapping, gs_panel = 1)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd2,
+		0x1f, 0x1f, 0x04, 0x06, 0x00, 0x1e, 0x1f, 0x1f,
+		0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f,
+	);
+
+	// SET_GIP_R_GS (CGOUTx_R signal mapping, gs_panel = 1)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd3,
+		0x1f, 0x1f, 0x05, 0x07, 0x01, 0x1e, 0x1f, 0x1f,
+		0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f,
+	);
+
+	// SETGIP1 (GIP signal timing 1)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd4,
+		0x30, 0x00, 0x00, 0x00, 0x00, 0x01, 0x10, 0x00,
+		0x03, 0x03, 0x68, 0x03, 0x40, 0x05, 0x00, 0x00,
+		0x00, 0xcc, 0x2d, 0x31, 0x02, 0x03, 0x68, 0x0c,
+		0x25, 0x00, 0x63, 0x03, 0x00,
+	);
+
+	// SETGIP2 (GIP signal timing 1)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xd5,
+		0x30, 0x08, 0x80, 0x18, 0x00, 0x00, 0x00, 0x18,
+		0x00, 0x00, 0x06, 0x60, 0x00, 0x07, 0x50, 0x00,
+		0x33, 0xc0, 0x00, 0x60, 0xc0, 0x00, 0x00, 0x00,
+		0x03, 0x60, 0x06, 0x10, 0x00, 0x00, 0x0f, 0x4f,
+		0x00, 0x10, 0x1f, 0x3f,
+	);
+
+	jd9161z_switch_page(&dsi_ctx, 0x02);
+
+	// SETRGBCYC2 (RGB IF source switch control timing)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc1,
+		0x60);
+
+	// ?
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xc2,
+		0x00, 0x18, 0x08, 0x1e, 0x25, 0x7c, 0xc7,
+	);
+
+	jd9161z_switch_page(&dsi_ctx, 0x00);
+
+	// GAS_CTRL (GAS function control)
+	mipi_dsi_dcs_write_seq_multi(&dsi_ctx, 0xbe,
+		0x4e,
+	);
+
+	mipi_dsi_dcs_set_tear_on_multi(&dsi_ctx, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
+
+	mipi_dsi_msleep(&dsi_ctx, 120);
+
+	mipi_dsi_dcs_exit_sleep_mode_multi(&dsi_ctx);
+
+	mipi_dsi_msleep(&dsi_ctx, 120);
+
+	mipi_dsi_dcs_set_display_on_multi(&dsi_ctx);
+
+	mipi_dsi_msleep(&dsi_ctx, 5);
+
+	return dsi_ctx.accum_err;
+};
+
+static const struct jadard_panel_desc zhunyi_z40046v2_desc = {
+	.mode = {
+		.clock		= 26700,
+
+		.hdisplay	= 480,
+		.hsync_start	= 480 + 20,
+		.hsync_end	= 480 + 20 + 20,
+		.htotal		= 480 + 20 + 20 + 20,
+
+		.vdisplay	= 800,
+		.vsync_start	= 800 + 12,
+		.vsync_end	= 800 + 12 + 4,
+		.vtotal		= 800 + 12 + 4 + 8,
+
+		.width_mm	= 52,
+		.height_mm	= 86,
+		.flags		= DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+		.type		= DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+	},
+	.lanes = 2,
+	.format = MIPI_DSI_FMT_RGB888,
+	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE |
+		MIPI_DSI_MODE_LPM,
+	.lp11_before_reset = true,
+	.reset_before_power_off_vcioo = true,
+	.vcioo_to_lp11_delay_ms = 5,
+	.lp11_to_reset_delay_ms = 10,
+	.backlight_off_to_display_off_delay_ms = 100,
+	.display_off_to_enter_sleep_delay_ms = 50,
+	.enter_sleep_to_reset_down_delay_ms = 100,
+	.init = zhunyi_z40046_init_cmds_v2,
+};
+
 static int jadard_dsi_probe(struct mipi_dsi_device *dsi)
 {
 	struct device *dev = &dsi->dev;
@@ -1463,6 +1763,14 @@ static const struct of_device_id jadard_of_match[] = {
 		.compatible = "radxa,display-8hd-ad002",
 		.data = &radxa_display_8hd_ad002_desc
 	},
+	{
+		.compatible = "zhunyi,z40046v1",
+		.data = &zhunyi_z40046v1_desc
+	},
+	{
+		.compatible = "zhunyi,z40046v2",
+		.data = &zhunyi_z40046v2_desc
+	},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, jadard_of_match);
-- 
2.43.0

Re: [PATCH 1/2] dt-bindings: display: panel: Add compatibles for Zhunyi Z40046

[Krzysztof Kozlowski]

On Thu, Mar 05, 2026 at 07:56:30PM +0000, Luca Leonardo Scorcia wrote:
> The Zhunyi Z40046 is a 480x800 24-bit WVGA DSI panel based on the
> Fitipower JD9161Z DSI controller found in the Xiaomi Mi Smart Clock
> x04g, apparently in two different variants.
> 
> The Fitipower JD9161Z LCD driver IC is very similar to the Jadard
> JD9365DA-H3, it just uses a different initialization sequence.
> 
> Since this is the first supported device from this vendor, document its
> name to the vendor-prefixes.yaml file as well.
> 
> Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
> ---
>  .../devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml   | 2 ++
>  Documentation/devicetree/bindings/vendor-prefixes.yaml          | 2 ++
>  2 files changed, 4 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml b/Documentation/devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml
> index 5802fb3c9ffe..da17072ffaaa 100644
> --- a/Documentation/devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml
> +++ b/Documentation/devicetree/bindings/display/panel/jadard,jd9365da-h3.yaml
> @@ -23,6 +23,8 @@ properties:
>            - melfas,lmfbx101117480
>            - radxa,display-10hd-ad001
>            - radxa,display-8hd-ad002
> +          - zhunyi,z40046v1
> +          - zhunyi,z40046v2
>        - const: jadard,jd9365da-h3
>  
>    reg:
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> index ee7fd3cfe203..18121440dc22 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> @@ -1913,6 +1913,8 @@ patternProperties:
>      description: Shenzhen Zkmagic Technology Co., Ltd.
>    "^zte,.*":
>      description: ZTE Corp.
> +  "^zhunyi,.*":

Don't mix up the order.

Domain is zhunyikeji, so should be the prefix.

Best regards,
Krzysztof