* [PATCH v3 0/3] Add support for Orange Pi 5 Pro
@ 2026-03-06 2:46 dennis
2026-03-06 2:46 ` [PATCH v3 1/3] dt-bindings: arm: rockchip: Add " dennis
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: dennis @ 2026-03-06 2:46 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: FUKAUMI Naoki, Hsun Lai, Jonas Karlman, Chaoyi Chen, John Clark,
Michael Opdenacker, Quentin Schulz, Andrew Lunn, Chukun Pan,
Alexey Charkov, Peter Robinson, Dennis Gilmore, Mykola Kvach,
Michael Riesch, Jimmy Hon, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel
From: Dennis Gilmore <dennis@ausil.us>
This series adds initial support for Orange Pi 5 Pro. The network
driver was just added. The only thing missing is the second HDMI port
that is connected via a DP to HDMI adaptor
The series was tested against Linux 7.0-rc2
Please take a look.
Thank you,
Dennis Gilmore
Changes in v3:
- moved leds from gpio-leds to pwm-leds
- remove disable-wp from sdio
- rename vcc3v3_pcie_eth regulator to vcc3v3_pcie_m2 to reflect the
purppose
- actually clean up the delete lines and comments missed in v2
- link to v2 https://lore.kernel.org/linux-devicetree/20260304025521.210377-1-dennis@ausil.us/
Changes in v2:
- moved items not shared by orangepi 5/5b/5 Pro from dtsi to 5 and 5b
dts files
- removed all the comments and deleted properties from 5 Pro dts
- Link to v1 https://lore.kernel.org/linux-devicetree/20260228205418.2944620-1-dennis@ausil.us/
Dennis Gilmore (3):
dt-bindings: arm: rockchip: Add Orange Pi 5 Pro
arm64: dts: rockchip: refactor items from Orange Pi 5/b to prep for
Pro
arm64: dts: rockchip: Add Orange Pi 5 Pro board support
.../devicetree/bindings/arm/rockchip.yaml | 1 +
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../dts/rockchip/rk3588s-orangepi-5-pro.dts | 311 ++++++++++++++++++
.../boot/dts/rockchip/rk3588s-orangepi-5.dts | 184 +++++++++++
.../boot/dts/rockchip/rk3588s-orangepi-5.dtsi | 202 +-----------
.../boot/dts/rockchip/rk3588s-orangepi-5b.dts | 181 ++++++++++
6 files changed, 691 insertions(+), 189 deletions(-)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
--
2.53.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 1/3] dt-bindings: arm: rockchip: Add Orange Pi 5 Pro
2026-03-06 2:46 [PATCH v3 0/3] Add support for Orange Pi 5 Pro dennis
@ 2026-03-06 2:46 ` dennis
2026-03-06 2:46 ` [PATCH v3 2/3] arm64: dts: rockchip: refactor items from Orange Pi 5/b to prep for Pro dennis
2026-03-06 2:46 ` [PATCH v3 3/3] arm64: dts: rockchip: Add Orange Pi 5 Pro board support dennis
2 siblings, 0 replies; 6+ messages in thread
From: dennis @ 2026-03-06 2:46 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: FUKAUMI Naoki, Hsun Lai, Jonas Karlman, Chaoyi Chen, John Clark,
Michael Opdenacker, Quentin Schulz, Andrew Lunn, Chukun Pan,
Alexey Charkov, Peter Robinson, Dennis Gilmore, Mykola Kvach,
Michael Riesch, Jimmy Hon, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel, Krzysztof Kozlowski
From: Dennis Gilmore <dennis@ausil.us>
Add compatible string for the Orange Pi 5 Pro.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index ae77ded9fe47..3c6b83a84463 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -1320,6 +1320,7 @@ properties:
items:
- enum:
- xunlong,orangepi-5
+ - xunlong,orangepi-5-pro
- xunlong,orangepi-5b
- const: rockchip,rk3588s
--
2.53.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 2/3] arm64: dts: rockchip: refactor items from Orange Pi 5/b to prep for Pro
2026-03-06 2:46 [PATCH v3 0/3] Add support for Orange Pi 5 Pro dennis
2026-03-06 2:46 ` [PATCH v3 1/3] dt-bindings: arm: rockchip: Add " dennis
@ 2026-03-06 2:46 ` dennis
2026-03-06 2:46 ` [PATCH v3 3/3] arm64: dts: rockchip: Add Orange Pi 5 Pro board support dennis
2 siblings, 0 replies; 6+ messages in thread
From: dennis @ 2026-03-06 2:46 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: FUKAUMI Naoki, Hsun Lai, Jonas Karlman, Chaoyi Chen, John Clark,
Michael Opdenacker, Quentin Schulz, Andrew Lunn, Chukun Pan,
Alexey Charkov, Peter Robinson, Dennis Gilmore, Mykola Kvach,
Michael Riesch, Jimmy Hon, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel
From: Dennis Gilmore <dennis@ausil.us>
The Orange Pi 5 Pro uses the same SoC and base as the Orange Pi 5 and
Orange Pi 5B but has had sound, USB, and leds wired up differently. The
boards also use gmac for ethernet where thre Pro has a PCIe attached NIC
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
---
.../boot/dts/rockchip/rk3588s-orangepi-5.dts | 184 ++++++++++++++++
.../boot/dts/rockchip/rk3588s-orangepi-5.dtsi | 202 ++----------------
.../boot/dts/rockchip/rk3588s-orangepi-5b.dts | 181 ++++++++++++++++
3 files changed, 378 insertions(+), 189 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
index 83b9b6645a1e..a102458d7f6f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dts
@@ -2,12 +2,62 @@
/dts-v1/;
+#include <dt-bindings/usb/pd.h>
#include "rk3588s-orangepi-5.dtsi"
/ {
model = "Xunlong Orange Pi 5";
compatible = "xunlong,orangepi-5", "rockchip,rk3588s";
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdmmc;
+ };
+
+ analog-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_detect>;
+ simple-audio-card,name = "rockchip,es8388";
+ simple-audio-card,bitclock-master = <&masterdai>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&masterdai>;
+ simple-audio-card,hp-det-gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,routing =
+ "Headphones", "LOUT1",
+ "Headphones", "ROUT1",
+ "LINPUT1", "Microphone Jack",
+ "RINPUT1", "Microphone Jack",
+ "LINPUT2", "Onboard Microphone",
+ "RINPUT2", "Onboard Microphone";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Microphone", "Onboard Microphone",
+ "Headphone", "Headphones";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+
+ masterdai: simple-audio-card,codec {
+ sound-dai = <&es8388>;
+ system-clock-frequency = <12288000>;
+ };
+ };
+
+ pwm-leds {
+ compatible = "pwm-leds";
+
+ led {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ linux,default-trigger = "heartbeat";
+ max-brightness = <255>;
+ pwms = <&pwm0 0 25000 0>;
+ };
+ };
+
vcc3v3_pcie20: regulator-vcc3v3-pcie20 {
compatible = "regulator-fixed";
enable-active-high;
@@ -21,12 +71,146 @@ vcc3v3_pcie20: regulator-vcc3v3-pcie20 {
};
};
+&gmac1 {
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-rxid";
+ pinctrl-0 = <&gmac1_miim
+ &gmac1_tx_bus2
+ &gmac1_rx_bus2
+ &gmac1_rgmii_clk
+ &gmac1_rgmii_bus>;
+ pinctrl-names = "default";
+ tx_delay = <0x42>;
+ status = "okay";
+};
+
+&i2c6 {
+ es8388: audio-codec@10 {
+ compatible = "everest,es8388", "everest,es8328";
+ reg = <0x10>;
+ clocks = <&cru I2S1_8CH_MCLKOUT>;
+ AVDD-supply = <&vcc_3v3_s0>;
+ DVDD-supply = <&vcc_1v8_s0>;
+ HPVDD-supply = <&vcc_3v3_s0>;
+ PVDD-supply = <&vcc_3v3_s0>;
+ assigned-clocks = <&cru I2S1_8CH_MCLKOUT>;
+ assigned-clock-rates = <12288000>;
+ #sound-dai-cells = <0>;
+ };
+
+ usbc0: usb-typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbc0_int>;
+ vbus-supply = <&vbus_typec>;
+ status = "okay";
+
+ usb_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ op-sink-microwatt = <1000000>;
+ power-role = "dual";
+ sink-pdos =
+ <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
+ source-pdos =
+ <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ try-power-role = "source";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usbc0_hs: endpoint {
+ remote-endpoint = <&usb_host0_xhci_drd_sw>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ usbc0_ss: endpoint {
+ remote-endpoint = <&usbdp_phy0_typec_ss>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ usbc0_sbu: endpoint {
+ remote-endpoint = <&usbdp_phy0_typec_sbu>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2s1_8ch {
+ rockchip,i2s-tx-route = <3 2 1 0>;
+ rockchip,i2s-rx-route = <1 3 2 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_sclk
+ &i2s1m0_mclk
+ &i2s1m0_lrck
+ &i2s1m0_sdi1
+ &i2s1m0_sdo3>;
+ status = "okay";
+};
+
&pcie2x1l2 {
reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
vpcie3v3-supply = <&vcc3v3_pcie20>;
status = "okay";
};
+&pwm0 {
+ pinctrl-0 = <&pwm0m2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
&sfc {
status = "okay";
};
+
+&usb_host0_xhci {
+ dr_mode = "otg";
+ usb-role-switch;
+
+ port {
+ usb_host0_xhci_drd_sw: endpoint {
+ remote-endpoint = <&usbc0_hs>;
+ };
+ };
+};
+
+&usb_host2_xhci {
+ status = "okay";
+};
+
+&usbdp_phy0 {
+ mode-switch;
+ orientation-switch;
+ sbu1-dc-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
+ sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy0_typec_ss: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_ss>;
+ };
+
+ usbdp_phy0_typec_sbu: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&usbc0_sbu>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dtsi
index dafad29f9854..7c7276968d95 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5.dtsi
@@ -3,19 +3,13 @@
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/leds/common.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include <dt-bindings/soc/rockchip,vop2.h>
-#include <dt-bindings/usb/pd.h>
#include "rk3588s.dtsi"
/ {
- aliases {
- ethernet0 = &gmac1;
- mmc0 = &sdmmc;
- };
-
chosen {
stdout-path = "serial2:1500000n8";
};
@@ -34,38 +28,6 @@ button-recovery {
};
};
- analog-sound {
- compatible = "simple-audio-card";
- pinctrl-names = "default";
- pinctrl-0 = <&hp_detect>;
- simple-audio-card,name = "rockchip,es8388";
- simple-audio-card,bitclock-master = <&masterdai>;
- simple-audio-card,format = "i2s";
- simple-audio-card,frame-master = <&masterdai>;
- simple-audio-card,hp-det-gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
- simple-audio-card,mclk-fs = <256>;
- simple-audio-card,routing =
- "Headphones", "LOUT1",
- "Headphones", "ROUT1",
- "LINPUT1", "Microphone Jack",
- "RINPUT1", "Microphone Jack",
- "LINPUT2", "Onboard Microphone",
- "RINPUT2", "Onboard Microphone";
- simple-audio-card,widgets =
- "Microphone", "Microphone Jack",
- "Microphone", "Onboard Microphone",
- "Headphone", "Headphones";
-
- simple-audio-card,cpu {
- sound-dai = <&i2s1_8ch>;
- };
-
- masterdai: simple-audio-card,codec {
- sound-dai = <&es8388>;
- system-clock-frequency = <12288000>;
- };
- };
-
hdmi0-con {
compatible = "hdmi-connector";
type = "a";
@@ -77,18 +39,6 @@ hdmi0_con_in: endpoint {
};
};
- pwm-leds {
- compatible = "pwm-leds";
-
- led {
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_STATUS;
- linux,default-trigger = "heartbeat";
- max-brightness = <255>;
- pwms = <&pwm0 0 25000 0>;
- };
- };
-
vbus_typec: regulator-vbus-typec {
compatible = "regulator-fixed";
enable-active-high;
@@ -101,15 +51,6 @@ vbus_typec: regulator-vbus-typec {
vin-supply = <&vcc5v0_sys>;
};
- vcc5v0_sys: regulator-vcc5v0-sys {
- compatible = "regulator-fixed";
- regulator-name = "vcc5v0_sys";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
vcc_3v3_sd_s0: regulator-vcc-3v3-sd-s0 {
compatible = "regulator-fixed";
gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_LOW>;
@@ -119,6 +60,15 @@ vcc_3v3_sd_s0: regulator-vcc-3v3-sd-s0 {
regulator-max-microvolt = <3300000>;
vin-supply = <&vcc_3v3_s3>;
};
+
+ vcc5v0_sys: regulator-vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
};
&combphy0_ps {
@@ -161,20 +111,6 @@ &cpu_l3 {
cpu-supply = <&vdd_cpu_lit_s0>;
};
-&gmac1 {
- clock_in_out = "output";
- phy-handle = <&rgmii_phy1>;
- phy-mode = "rgmii-rxid";
- pinctrl-0 = <&gmac1_miim
- &gmac1_tx_bus2
- &gmac1_rx_bus2
- &gmac1_rgmii_clk
- &gmac1_rgmii_bus>;
- pinctrl-names = "default";
- tx_delay = <0x42>;
- status = "okay";
-};
-
&gpu {
mali-supply = <&vdd_gpu_s0>;
status = "okay";
@@ -270,69 +206,6 @@ &i2c6 {
pinctrl-0 = <&i2c6m3_xfer>;
status = "okay";
- es8388: audio-codec@10 {
- compatible = "everest,es8388", "everest,es8328";
- reg = <0x10>;
- clocks = <&cru I2S1_8CH_MCLKOUT>;
- AVDD-supply = <&vcc_3v3_s0>;
- DVDD-supply = <&vcc_1v8_s0>;
- HPVDD-supply = <&vcc_3v3_s0>;
- PVDD-supply = <&vcc_3v3_s0>;
- assigned-clocks = <&cru I2S1_8CH_MCLKOUT>;
- assigned-clock-rates = <12288000>;
- #sound-dai-cells = <0>;
- };
-
- usbc0: usb-typec@22 {
- compatible = "fcs,fusb302";
- reg = <0x22>;
- interrupt-parent = <&gpio0>;
- interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&usbc0_int>;
- vbus-supply = <&vbus_typec>;
- status = "okay";
-
- usb_con: connector {
- compatible = "usb-c-connector";
- label = "USB-C";
- data-role = "dual";
- op-sink-microwatt = <1000000>;
- power-role = "dual";
- sink-pdos =
- <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
- source-pdos =
- <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
- try-power-role = "source";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- usbc0_hs: endpoint {
- remote-endpoint = <&usb_host0_xhci_drd_sw>;
- };
- };
-
- port@1 {
- reg = <1>;
- usbc0_ss: endpoint {
- remote-endpoint = <&usbdp_phy0_typec_ss>;
- };
- };
-
- port@2 {
- reg = <2>;
- usbc0_sbu: endpoint {
- remote-endpoint = <&usbdp_phy0_typec_sbu>;
- };
- };
- };
- };
- };
-
hym8563: rtc@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
@@ -346,18 +219,6 @@ hym8563: rtc@51 {
};
};
-&i2s1_8ch {
- rockchip,i2s-tx-route = <3 2 1 0>;
- rockchip,i2s-rx-route = <1 3 2 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2s1m0_sclk
- &i2s1m0_mclk
- &i2s1m0_lrck
- &i2s1m0_sdi1
- &i2s1m0_sdo3>;
- status = "okay";
-};
-
&i2s5_8ch {
status = "okay";
};
@@ -404,12 +265,6 @@ typec5v_pwren: typec5v-pwren {
};
};
-&pwm0 {
- pinctrl-0 = <&pwm0m2_pins>;
- pinctrl-names = "default";
- status = "okay";
-};
-
&rknn_core_0 {
npu-supply = <&vdd_npu_s0>;
sram-supply = <&vdd_npu_s0>;
@@ -840,29 +695,6 @@ &uart2 {
status = "okay";
};
-&usbdp_phy0 {
- mode-switch;
- orientation-switch;
- sbu1-dc-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
- sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
- status = "okay";
-
- port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- usbdp_phy0_typec_ss: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&usbc0_ss>;
- };
-
- usbdp_phy0_typec_sbu: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&usbc0_sbu>;
- };
- };
-};
-
&usb_host0_ehci {
status = "okay";
};
@@ -872,15 +704,7 @@ &usb_host0_ohci {
};
&usb_host0_xhci {
- dr_mode = "otg";
- usb-role-switch;
status = "okay";
-
- port {
- usb_host0_xhci_drd_sw: endpoint {
- remote-endpoint = <&usbc0_hs>;
- };
- };
};
&usb_host1_ehci {
@@ -891,15 +715,15 @@ &usb_host1_ohci {
status = "okay";
};
-&usb_host2_xhci {
+&usbdp_phy0 {
status = "okay";
};
-&vop_mmu {
+&vop {
status = "okay";
};
-&vop {
+&vop_mmu {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5b.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5b.dts
index d21ec320d295..5acd96969ddf 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5b.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5b.dts
@@ -2,6 +2,7 @@
/dts-v1/;
+#include <dt-bindings/usb/pd.h>
#include "rk3588s-orangepi-5.dtsi"
/ {
@@ -9,11 +10,191 @@ / {
compatible = "xunlong,orangepi-5b", "rockchip,rk3588s";
aliases {
+ ethernet0 = &gmac1;
mmc0 = &sdhci;
mmc1 = &sdmmc;
};
+
+ analog-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_detect>;
+ simple-audio-card,name = "rockchip,es8388";
+ simple-audio-card,bitclock-master = <&masterdai>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&masterdai>;
+ simple-audio-card,hp-det-gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,routing =
+ "Headphones", "LOUT1",
+ "Headphones", "ROUT1",
+ "LINPUT1", "Microphone Jack",
+ "RINPUT1", "Microphone Jack",
+ "LINPUT2", "Onboard Microphone",
+ "RINPUT2", "Onboard Microphone";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Microphone", "Onboard Microphone",
+ "Headphone", "Headphones";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+
+ masterdai: simple-audio-card,codec {
+ sound-dai = <&es8388>;
+ system-clock-frequency = <12288000>;
+ };
+ };
+
+ pwm-leds {
+ compatible = "pwm-leds";
+
+ led {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ linux,default-trigger = "heartbeat";
+ max-brightness = <255>;
+ pwms = <&pwm0 0 25000 0>;
+ };
+ };
+
+};
+
+&gmac1 {
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-rxid";
+ pinctrl-0 = <&gmac1_miim
+ &gmac1_tx_bus2
+ &gmac1_rx_bus2
+ &gmac1_rgmii_clk
+ &gmac1_rgmii_bus>;
+ pinctrl-names = "default";
+ tx_delay = <0x42>;
+ status = "okay";
+};
+
+&i2c6 {
+ es8388: audio-codec@10 {
+ compatible = "everest,es8388", "everest,es8328";
+ reg = <0x10>;
+ clocks = <&cru I2S1_8CH_MCLKOUT>;
+ AVDD-supply = <&vcc_3v3_s0>;
+ DVDD-supply = <&vcc_1v8_s0>;
+ HPVDD-supply = <&vcc_3v3_s0>;
+ PVDD-supply = <&vcc_3v3_s0>;
+ assigned-clocks = <&cru I2S1_8CH_MCLKOUT>;
+ assigned-clock-rates = <12288000>;
+ #sound-dai-cells = <0>;
+ };
+
+ usbc0: usb-typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbc0_int>;
+ vbus-supply = <&vbus_typec>;
+ status = "okay";
+
+ usb_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ op-sink-microwatt = <1000000>;
+ power-role = "dual";
+ sink-pdos =
+ <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
+ source-pdos =
+ <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+ try-power-role = "source";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usbc0_hs: endpoint {
+ remote-endpoint = <&usb_host0_xhci_drd_sw>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ usbc0_ss: endpoint {
+ remote-endpoint = <&usbdp_phy0_typec_ss>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ usbc0_sbu: endpoint {
+ remote-endpoint = <&usbdp_phy0_typec_sbu>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2s1_8ch {
+ rockchip,i2s-tx-route = <3 2 1 0>;
+ rockchip,i2s-rx-route = <1 3 2 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_sclk
+ &i2s1m0_mclk
+ &i2s1m0_lrck
+ &i2s1m0_sdi1
+ &i2s1m0_sdo3>;
+ status = "okay";
+};
+
+&pwm0 {
+ pinctrl-0 = <&pwm0m2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
};
&sdhci {
status = "okay";
};
+
+&usb_host0_xhci {
+ dr_mode = "otg";
+ usb-role-switch;
+
+ port {
+ usb_host0_xhci_drd_sw: endpoint {
+ remote-endpoint = <&usbc0_hs>;
+ };
+ };
+};
+
+&usb_host2_xhci {
+ status = "okay";
+};
+
+&usbdp_phy0 {
+ mode-switch;
+ orientation-switch;
+ sbu1-dc-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
+ sbu2-dc-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy0_typec_ss: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_ss>;
+ };
+
+ usbdp_phy0_typec_sbu: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&usbc0_sbu>;
+ };
+ };
+};
--
2.53.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 3/3] arm64: dts: rockchip: Add Orange Pi 5 Pro board support
2026-03-06 2:46 [PATCH v3 0/3] Add support for Orange Pi 5 Pro dennis
2026-03-06 2:46 ` [PATCH v3 1/3] dt-bindings: arm: rockchip: Add " dennis
2026-03-06 2:46 ` [PATCH v3 2/3] arm64: dts: rockchip: refactor items from Orange Pi 5/b to prep for Pro dennis
@ 2026-03-06 2:46 ` dennis
2026-03-06 3:28 ` Jimmy Hon
2 siblings, 1 reply; 6+ messages in thread
From: dennis @ 2026-03-06 2:46 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner
Cc: FUKAUMI Naoki, Hsun Lai, Jonas Karlman, Chaoyi Chen, John Clark,
Michael Opdenacker, Quentin Schulz, Andrew Lunn, Chukun Pan,
Alexey Charkov, Peter Robinson, Dennis Gilmore, Mykola Kvach,
Michael Riesch, Jimmy Hon, devicetree, linux-arm-kernel,
linux-rockchip, linux-kernel
From: Dennis Gilmore <dennis@ausil.us>
Add device tree for the Xunlong Orange Pi 5 Pro (RK3588S).
- eMMC module, you can optionally solder a SPI NOR in place and turn
off the eMMC
- PCIe-attached NIC (pcie2x1l1)
- PCIe NVMe slot (pcie2x1l2)
- AP6256 WiFi (BCM43456) via SDIO with mmc-pwrseq
- BCM4345C5 Bluetooth
- es8388 audio
- USB 2.0 and USB 3.0
Vendors description and links to schematics available:
http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-5-Pro.html
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../dts/rockchip/rk3588s-orangepi-5-pro.dts | 311 ++++++++++++++++++
2 files changed, 312 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 4d384f153c13..c99dca2ae9e7 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -214,6 +214,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5b.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5-pro.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-cm5-base.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-radxa-cm5-io.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-roc-pc.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
new file mode 100644
index 000000000000..d848891e09be
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3588s-orangepi-5.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi 5 Pro";
+ compatible = "xunlong,orangepi-5-pro", "rockchip,rk3588s";
+
+ aliases {
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc;
+ mmc2 = &sdio;
+ };
+
+ analog-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_detect>;
+ simple-audio-card,bitclock-master = <&masterdai>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&masterdai>;
+ simple-audio-card,hp-det-gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,name = "rockchip,es8388";
+ simple-audio-card,routing =
+ "Headphones", "LOUT1",
+ "Headphones", "ROUT1",
+ "LINPUT1", "Microphone Jack",
+ "RINPUT1", "Microphone Jack",
+ "LINPUT2", "Onboard Microphone",
+ "RINPUT2", "Onboard Microphone";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Microphone", "Onboard Microphone",
+ "Headphone", "Headphones";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s2_2ch>;
+ };
+
+ masterdai: simple-audio-card,codec {
+ sound-dai = <&es8388>;
+ system-clock-frequency = <12288000>;
+ };
+ };
+
+ pwm-leds {
+ compatible = "pwm-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ linux,default-trigger = "heartbeat";
+ max-brightness = <255>;
+ pwms = <&pwm15 0 1000000 0>;
+ };
+
+ led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_ACTIVITY;
+ linux,default-trigger = "heartbeat";
+ max-brightness = <255>;
+ pwms = <&pwm3 0 1000000 0>;
+ };
+ };
+
+ fan: pwm-fan {
+ compatible = "pwm-fan";
+ #cooling-cells = <2>;
+ cooling-levels = <0 50 100 150 200 255>;
+ fan-supply = <&vcc5v0_sys>;
+ pwms = <&pwm2 0 20000000 0>;
+ };
+
+ vcc3v3_pcie_m2: regulator-vcc3v3-pcie-m2 {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pcie_m2";
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_pcie20: regulator-vcc3v3-pcie20 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pcie20";
+ startup-delay-us = <50000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_otg: regulator-vcc5v0-otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_otg_en>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "vcc5v0_otg";
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&hym8563>;
+ clock-names = "ext_clock";
+ post-power-on-delay-ms = <200>;
+ reset-gpios = <&gpio0 RK_PD0 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1m4_xfer>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3m0_xfer>;
+ status = "okay";
+
+ es8388: audio-codec@11 {
+ compatible = "everest,es8388", "everest,es8328";
+ reg = <0x11>;
+ #sound-dai-cells = <0>;
+ AVDD-supply = <&vcc_3v3_s0>;
+ DVDD-supply = <&vcc_1v8_s0>;
+ HPVDD-supply = <&vcc_3v3_s0>;
+ PVDD-supply = <&vcc_3v3_s0>;
+ assigned-clock-rates = <12288000>;
+ assigned-clocks = <&cru I2S2_2CH_MCLKOUT>;
+ clocks = <&cru I2S2_2CH_MCLKOUT>;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4m3_xfer>;
+ status = "okay";
+};
+
+&i2s2_2ch {
+ pinctrl-0 = <&i2s2m1_lrck &i2s2m1_mclk &i2s2m1_sclk
+ &i2s2m1_sdi &i2s2m1_sdo>;
+ status = "okay";
+};
+
+&package_thermal {
+ polling-delay = <1000>;
+
+ cooling-maps {
+ map0 {
+ trip = <&package_fan0>;
+ cooling-device = <&fan THERMAL_NO_LIMIT 1>;
+ };
+
+ map1 {
+ trip = <&package_fan1>;
+ cooling-device = <&fan 2 THERMAL_NO_LIMIT>;
+ };
+ };
+
+ trips {
+ package_fan0: package-fan0 {
+ hysteresis = <2000>;
+ temperature = <55000>;
+ type = "active";
+ };
+
+ package_fan1: package-fan1 {
+ hysteresis = <2000>;
+ temperature = <65000>;
+ type = "active";
+ };
+ };
+};
+
+/* NVMe */
+&pcie2x1l1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie30x1m1_1_clkreqn &pcie30x1m1_1_waken>;
+ reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
+ supports-clkreq;
+ vpcie3v3-supply = <&vcc3v3_pcie_m2>;
+ status = "okay";
+};
+
+/* NIC */
+&pcie2x1l2 {
+ reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie20>;
+ status = "okay";
+};
+
+&pinctrl {
+ bluetooth {
+ bt_wake_gpio: bt-wake-pin {
+ rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_wake_host_irq: bt-wake-host-irq {
+ rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ usb {
+ vcc5v0_otg_en: vcc5v0-otg-en {
+ rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wlan {
+ wifi_host_wake_irq: wifi-host-wake-irq {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+};
+
+&pwm15 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm15m2_pins>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2m1_pins>;
+ status = "okay";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3m2_pins>;
+ status = "okay";
+};
+
+&sdhci {
+ status = "okay";
+};
+
+&sdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ max-frequency = <150000000>;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ no-mmc;
+ no-sd;
+ non-removable;
+ sd-uhs-sdr104;
+ status = "okay";
+
+ ap6256: wifi@1 {
+ compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+ interrupt-names = "host-wake";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA0 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_host_wake_irq>;
+ };
+};
+
+&u2phy0_otg {
+ phy-supply = <&vcc5v0_otg>;
+};
+
+&uart9 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart9m2_xfer &uart9m2_ctsn &uart9m2_rtsn>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4345c5";
+ clocks = <&hym8563>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+ interrupt-names = "host-wakeup";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PC5 IRQ_TYPE_LEVEL_HIGH>;
+ max-speed = <1500000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_wake_host_irq &bt_wake_gpio>;
+ shutdown-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+ vbat-supply = <&vcc_3v3_s3>;
+ vddio-supply = <&vcc_1v8_s3>;
+ };
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+};
+
+&usbdp_phy0 {
+ rockchip,dp-lane-mux = <0 1>;
+};
--
2.53.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v3 3/3] arm64: dts: rockchip: Add Orange Pi 5 Pro board support
2026-03-06 2:46 ` [PATCH v3 3/3] arm64: dts: rockchip: Add Orange Pi 5 Pro board support dennis
@ 2026-03-06 3:28 ` Jimmy Hon
2026-03-10 2:39 ` Dennis Gilmore
0 siblings, 1 reply; 6+ messages in thread
From: Jimmy Hon @ 2026-03-06 3:28 UTC (permalink / raw)
To: dennis
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner,
FUKAUMI Naoki, Hsun Lai, Jonas Karlman, Chaoyi Chen, John Clark,
Michael Opdenacker, Quentin Schulz, Andrew Lunn, Chukun Pan,
Alexey Charkov, Peter Robinson, Mykola Kvach, Michael Riesch,
devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
On Thu, Mar 5, 2026 at 8:46 PM <dennis@ausil.us> wrote:
>
> From: Dennis Gilmore <dennis@ausil.us>
>
> Add device tree for the Xunlong Orange Pi 5 Pro (RK3588S).
>
> - eMMC module, you can optionally solder a SPI NOR in place and turn
> off the eMMC
> - PCIe-attached NIC (pcie2x1l1)
> - PCIe NVMe slot (pcie2x1l2)
> - AP6256 WiFi (BCM43456) via SDIO with mmc-pwrseq
> - BCM4345C5 Bluetooth
> - es8388 audio
> - USB 2.0 and USB 3.0
>
> Vendors description and links to schematics available:
> http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-5-Pro.html
>
> Signed-off-by: Dennis Gilmore <dennis@ausil.us>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../dts/rockchip/rk3588s-orangepi-5-pro.dts | 311 ++++++++++++++++++
> 2 files changed, 312 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 4d384f153c13..c99dca2ae9e7 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -214,6 +214,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5b.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5-pro.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-cm5-base.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-radxa-cm5-io.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-roc-pc.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
> new file mode 100644
> index 000000000000..d848891e09be
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
> @@ -0,0 +1,311 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include "rk3588s-orangepi-5.dtsi"
> +
> +/ {
> + model = "Xunlong Orange Pi 5 Pro";
> + compatible = "xunlong,orangepi-5-pro", "rockchip,rk3588s";
> +
> + aliases {
> + mmc0 = &sdhci;
> + mmc1 = &sdmmc;
> + mmc2 = &sdio;
> + };
> +
> + analog-sound {
> + compatible = "simple-audio-card";
> + pinctrl-names = "default";
> + pinctrl-0 = <&hp_detect>;
> + simple-audio-card,bitclock-master = <&masterdai>;
> + simple-audio-card,format = "i2s";
> + simple-audio-card,frame-master = <&masterdai>;
> + simple-audio-card,hp-det-gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
> + simple-audio-card,mclk-fs = <256>;
> + simple-audio-card,name = "rockchip,es8388";
> + simple-audio-card,routing =
> + "Headphones", "LOUT1",
> + "Headphones", "ROUT1",
> + "LINPUT1", "Microphone Jack",
> + "RINPUT1", "Microphone Jack",
> + "LINPUT2", "Onboard Microphone",
> + "RINPUT2", "Onboard Microphone";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Microphone", "Onboard Microphone",
> + "Headphone", "Headphones";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s2_2ch>;
> + };
> +
> + masterdai: simple-audio-card,codec {
> + sound-dai = <&es8388>;
> + system-clock-frequency = <12288000>;
> + };
> + };
> +
> + pwm-leds {
> + compatible = "pwm-leds";
> +
> + led-0 {
> + color = <LED_COLOR_ID_BLUE>;
> + function = LED_FUNCTION_STATUS;
> + linux,default-trigger = "heartbeat";
> + max-brightness = <255>;
> + pwms = <&pwm15 0 1000000 0>;
> + };
> +
> + led-1 {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_ACTIVITY;
> + linux,default-trigger = "heartbeat";
> + max-brightness = <255>;
> + pwms = <&pwm3 0 1000000 0>;
> + };
> + };
> +
> + fan: pwm-fan {
> + compatible = "pwm-fan";
> + #cooling-cells = <2>;
> + cooling-levels = <0 50 100 150 200 255>;
> + fan-supply = <&vcc5v0_sys>;
> + pwms = <&pwm2 0 20000000 0>;
> + };
> +
> + vcc3v3_pcie_m2: regulator-vcc3v3-pcie-m2 {
> + compatible = "regulator-fixed";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <3300000>;
> + regulator-min-microvolt = <3300000>;
> + regulator-name = "vcc3v3_pcie_m2";
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc3v3_pcie20: regulator-vcc3v3-pcie20 {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
> + regulator-boot-on;
> + regulator-max-microvolt = <3300000>;
> + regulator-min-microvolt = <3300000>;
> + regulator-name = "vcc3v3_pcie20";
Is this vcc3v3_phy1 in the schematic?
> + startup-delay-us = <50000>;
> + vin-supply = <&vcc5v0_sys>;
according to the schematic, this is fed by vcc_3v3_s3
> + };
> +
> + vcc5v0_otg: regulator-vcc5v0-otg {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&vcc5v0_otg_en>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <5000000>;
> + regulator-min-microvolt = <5000000>;
> + regulator-name = "vcc5v0_otg";
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&hym8563>;
> + clock-names = "ext_clock";
> + post-power-on-delay-ms = <200>;
> + reset-gpios = <&gpio0 RK_PD0 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1m4_xfer>;
> + status = "okay";
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3m0_xfer>;
> + status = "okay";
> +
> + es8388: audio-codec@11 {
> + compatible = "everest,es8388", "everest,es8328";
> + reg = <0x11>;
> + #sound-dai-cells = <0>;
> + AVDD-supply = <&vcc_3v3_s0>;
> + DVDD-supply = <&vcc_1v8_s0>;
> + HPVDD-supply = <&vcc_3v3_s0>;
> + PVDD-supply = <&vcc_3v3_s0>;
> + assigned-clock-rates = <12288000>;
> + assigned-clocks = <&cru I2S2_2CH_MCLKOUT>;
> + clocks = <&cru I2S2_2CH_MCLKOUT>;
> + };
> +};
> +
> +&i2c4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c4m3_xfer>;
> + status = "okay";
> +};
> +
> +&i2s2_2ch {
> + pinctrl-0 = <&i2s2m1_lrck &i2s2m1_mclk &i2s2m1_sclk
> + &i2s2m1_sdi &i2s2m1_sdo>;
> + status = "okay";
> +};
> +
> +&package_thermal {
> + polling-delay = <1000>;
> +
> + cooling-maps {
> + map0 {
> + trip = <&package_fan0>;
> + cooling-device = <&fan THERMAL_NO_LIMIT 1>;
> + };
> +
> + map1 {
> + trip = <&package_fan1>;
> + cooling-device = <&fan 2 THERMAL_NO_LIMIT>;
> + };
> + };
> +
> + trips {
> + package_fan0: package-fan0 {
> + hysteresis = <2000>;
> + temperature = <55000>;
> + type = "active";
> + };
> +
> + package_fan1: package-fan1 {
> + hysteresis = <2000>;
> + temperature = <65000>;
> + type = "active";
> + };
> + };
> +};
> +
> +/* NVMe */
> +&pcie2x1l1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie30x1m1_1_clkreqn &pcie30x1m1_1_waken>;
> + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
> + supports-clkreq;
> + vpcie3v3-supply = <&vcc3v3_pcie_m2>;
Is this real? In the schematic, the supply looks like vcc_3v3_s3.
> + status = "okay";
> +};
> +
> +/* NIC */
> +&pcie2x1l2 {
> + reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc3v3_pcie20>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + bluetooth {
> + bt_wake_gpio: bt-wake-pin {
> + rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + bt_wake_host_irq: bt-wake-host-irq {
> + rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + usb {
> + vcc5v0_otg_en: vcc5v0-otg-en {
> + rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + wlan {
> + wifi_host_wake_irq: wifi-host-wake-irq {
> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +};
> +
> +&pwm15 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm15m2_pins>;
> + status = "okay";
> +};
> +
> +&pwm2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm2m1_pins>;
> + status = "okay";
> +};
> +
> +&pwm3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm3m2_pins>;
> + status = "okay";
> +};
> +
> +&sdhci {
> + status = "okay";
> +};
> +
> +&sdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + keep-power-in-suspend;
> + max-frequency = <150000000>;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + no-mmc;
> + no-sd;
> + non-removable;
> + sd-uhs-sdr104;
> + status = "okay";
> +
> + ap6256: wifi@1 {
> + compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
> + reg = <1>;
> + interrupt-names = "host-wake";
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PA0 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_host_wake_irq>;
> + };
> +};
> +
> +&u2phy0_otg {
> + phy-supply = <&vcc5v0_otg>;
> +};
> +
> +&uart9 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart9m2_xfer &uart9m2_ctsn &uart9m2_rtsn>;
> + uart-has-rtscts;
> + status = "okay";
> +
> + bluetooth {
> + compatible = "brcm,bcm4345c5";
> + clocks = <&hym8563>;
> + clock-names = "lpo";
> + device-wakeup-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
> + interrupt-names = "host-wakeup";
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PC5 IRQ_TYPE_LEVEL_HIGH>;
> + max-speed = <1500000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_wake_host_irq &bt_wake_gpio>;
> + shutdown-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
> + vbat-supply = <&vcc_3v3_s3>;
> + vddio-supply = <&vcc_1v8_s3>;
> + };
> +};
> +
> +&usb_host0_xhci {
> + dr_mode = "host";
> +};
> +
> +&usbdp_phy0 {
> + rockchip,dp-lane-mux = <0 1>;
> +};
> --
> 2.53.0
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v3 3/3] arm64: dts: rockchip: Add Orange Pi 5 Pro board support
2026-03-06 3:28 ` Jimmy Hon
@ 2026-03-10 2:39 ` Dennis Gilmore
0 siblings, 0 replies; 6+ messages in thread
From: Dennis Gilmore @ 2026-03-10 2:39 UTC (permalink / raw)
To: Jimmy Hon
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Heiko Stuebner,
FUKAUMI Naoki, Hsun Lai, Jonas Karlman, Chaoyi Chen, John Clark,
Michael Opdenacker, Quentin Schulz, Andrew Lunn, Chukun Pan,
Alexey Charkov, Peter Robinson, Mykola Kvach, Michael Riesch,
devicetree, linux-arm-kernel, linux-rockchip, linux-kernel
On Thu, Mar 5, 2026 at 9:29 PM Jimmy Hon <honyuenkwun@gmail.com> wrote:
>
> On Thu, Mar 5, 2026 at 8:46 PM <dennis@ausil.us> wrote:
> >
> > From: Dennis Gilmore <dennis@ausil.us>
> >
> > Add device tree for the Xunlong Orange Pi 5 Pro (RK3588S).
> >
> > - eMMC module, you can optionally solder a SPI NOR in place and turn
> > off the eMMC
> > - PCIe-attached NIC (pcie2x1l1)
> > - PCIe NVMe slot (pcie2x1l2)
> > - AP6256 WiFi (BCM43456) via SDIO with mmc-pwrseq
> > - BCM4345C5 Bluetooth
> > - es8388 audio
> > - USB 2.0 and USB 3.0
> >
> > Vendors description and links to schematics available:
> > http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-5-Pro.html
> >
> > Signed-off-by: Dennis Gilmore <dennis@ausil.us>
> > ---
> > arch/arm64/boot/dts/rockchip/Makefile | 1 +
> > .../dts/rockchip/rk3588s-orangepi-5-pro.dts | 311 ++++++++++++++++++
> > 2 files changed, 312 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> > index 4d384f153c13..c99dca2ae9e7 100644
> > --- a/arch/arm64/boot/dts/rockchip/Makefile
> > +++ b/arch/arm64/boot/dts/rockchip/Makefile
> > @@ -214,6 +214,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5b.dtb
> > +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5-pro.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-cm5-base.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-radxa-cm5-io.dtb
> > dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-roc-pc.dtb
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
> > new file mode 100644
> > index 000000000000..d848891e09be
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
> > @@ -0,0 +1,311 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +
> > +/dts-v1/;
> > +
> > +#include "rk3588s-orangepi-5.dtsi"
> > +
> > +/ {
> > + model = "Xunlong Orange Pi 5 Pro";
> > + compatible = "xunlong,orangepi-5-pro", "rockchip,rk3588s";
> > +
> > + aliases {
> > + mmc0 = &sdhci;
> > + mmc1 = &sdmmc;
> > + mmc2 = &sdio;
> > + };
> > +
> > + analog-sound {
> > + compatible = "simple-audio-card";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&hp_detect>;
> > + simple-audio-card,bitclock-master = <&masterdai>;
> > + simple-audio-card,format = "i2s";
> > + simple-audio-card,frame-master = <&masterdai>;
> > + simple-audio-card,hp-det-gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
> > + simple-audio-card,mclk-fs = <256>;
> > + simple-audio-card,name = "rockchip,es8388";
> > + simple-audio-card,routing =
> > + "Headphones", "LOUT1",
> > + "Headphones", "ROUT1",
> > + "LINPUT1", "Microphone Jack",
> > + "RINPUT1", "Microphone Jack",
> > + "LINPUT2", "Onboard Microphone",
> > + "RINPUT2", "Onboard Microphone";
> > + simple-audio-card,widgets =
> > + "Microphone", "Microphone Jack",
> > + "Microphone", "Onboard Microphone",
> > + "Headphone", "Headphones";
> > +
> > + simple-audio-card,cpu {
> > + sound-dai = <&i2s2_2ch>;
> > + };
> > +
> > + masterdai: simple-audio-card,codec {
> > + sound-dai = <&es8388>;
> > + system-clock-frequency = <12288000>;
> > + };
> > + };
> > +
> > + pwm-leds {
> > + compatible = "pwm-leds";
> > +
> > + led-0 {
> > + color = <LED_COLOR_ID_BLUE>;
> > + function = LED_FUNCTION_STATUS;
> > + linux,default-trigger = "heartbeat";
> > + max-brightness = <255>;
> > + pwms = <&pwm15 0 1000000 0>;
> > + };
> > +
> > + led-1 {
> > + color = <LED_COLOR_ID_GREEN>;
> > + function = LED_FUNCTION_ACTIVITY;
> > + linux,default-trigger = "heartbeat";
> > + max-brightness = <255>;
> > + pwms = <&pwm3 0 1000000 0>;
> > + };
> > + };
> > +
> > + fan: pwm-fan {
> > + compatible = "pwm-fan";
> > + #cooling-cells = <2>;
> > + cooling-levels = <0 50 100 150 200 255>;
> > + fan-supply = <&vcc5v0_sys>;
> > + pwms = <&pwm2 0 20000000 0>;
> > + };
> > +
> > + vcc3v3_pcie_m2: regulator-vcc3v3-pcie-m2 {
> > + compatible = "regulator-fixed";
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-name = "vcc3v3_pcie_m2";
> > + vin-supply = <&vcc5v0_sys>;
> > + };
> > +
> > + vcc3v3_pcie20: regulator-vcc3v3-pcie20 {
> > + compatible = "regulator-fixed";
> > + enable-active-high;
> > + gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
> > + regulator-boot-on;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-name = "vcc3v3_pcie20";
> Is this vcc3v3_phy1 in the schematic?
>
> > + startup-delay-us = <50000>;
> > + vin-supply = <&vcc5v0_sys>;
> according to the schematic, this is fed by vcc_3v3_s3
Thanks for the review, Jimmy.
You're right on the vin-supply point — this should be vcc_3v3_s3, not
vcc5v0_sys. I'll fix it
Regarding "Is this vcc3v3_phy1?", that is the source. vcc3v3_pcie20
came from copying from rk3588s-orangepi-5.dts I will rename it to
match the label in the schematic
> > + };
> > +
> > + vcc5v0_otg: regulator-vcc5v0-otg {
> > + compatible = "regulator-fixed";
> > + enable-active-high;
> > + gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&vcc5v0_otg_en>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-min-microvolt = <5000000>;
> > + regulator-name = "vcc5v0_otg";
> > + vin-supply = <&vcc5v0_sys>;
> > + };
> > +
> > + sdio_pwrseq: sdio-pwrseq {
> > + compatible = "mmc-pwrseq-simple";
> > + clocks = <&hym8563>;
> > + clock-names = "ext_clock";
> > + post-power-on-delay-ms = <200>;
> > + reset-gpios = <&gpio0 RK_PD0 GPIO_ACTIVE_LOW>;
> > + };
> > +};
> > +
> > +&i2c1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c1m4_xfer>;
> > + status = "okay";
> > +};
> > +
> > +&i2c3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c3m0_xfer>;
> > + status = "okay";
> > +
> > + es8388: audio-codec@11 {
> > + compatible = "everest,es8388", "everest,es8328";
> > + reg = <0x11>;
> > + #sound-dai-cells = <0>;
> > + AVDD-supply = <&vcc_3v3_s0>;
> > + DVDD-supply = <&vcc_1v8_s0>;
> > + HPVDD-supply = <&vcc_3v3_s0>;
> > + PVDD-supply = <&vcc_3v3_s0>;
> > + assigned-clock-rates = <12288000>;
> > + assigned-clocks = <&cru I2S2_2CH_MCLKOUT>;
> > + clocks = <&cru I2S2_2CH_MCLKOUT>;
> > + };
> > +};
> > +
> > +&i2c4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c4m3_xfer>;
> > + status = "okay";
> > +};
> > +
> > +&i2s2_2ch {
> > + pinctrl-0 = <&i2s2m1_lrck &i2s2m1_mclk &i2s2m1_sclk
> > + &i2s2m1_sdi &i2s2m1_sdo>;
> > + status = "okay";
> > +};
> > +
> > +&package_thermal {
> > + polling-delay = <1000>;
> > +
> > + cooling-maps {
> > + map0 {
> > + trip = <&package_fan0>;
> > + cooling-device = <&fan THERMAL_NO_LIMIT 1>;
> > + };
> > +
> > + map1 {
> > + trip = <&package_fan1>;
> > + cooling-device = <&fan 2 THERMAL_NO_LIMIT>;
> > + };
> > + };
> > +
> > + trips {
> > + package_fan0: package-fan0 {
> > + hysteresis = <2000>;
> > + temperature = <55000>;
> > + type = "active";
> > + };
> > +
> > + package_fan1: package-fan1 {
> > + hysteresis = <2000>;
> > + temperature = <65000>;
> > + type = "active";
> > + };
> > + };
> > +};
> > +
> > +/* NVMe */
> > +&pcie2x1l1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pcie30x1m1_1_clkreqn &pcie30x1m1_1_waken>;
> > + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
> > + supports-clkreq;
> > + vpcie3v3-supply = <&vcc3v3_pcie_m2>;
> Is this real? In the schematic, the supply looks like vcc_3v3_s3.
It is not real, since there's no discrete regulator (VCC_3V3_S3 feeds
the M.2 slot directly), I'll drop that node and have pcie2x1l1
reference vcc_3v3_s3 directly.
Dennis
> > + status = "okay";
> > +};
> > +
> > +/* NIC */
> > +&pcie2x1l2 {
> > + reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
> > + vpcie3v3-supply = <&vcc3v3_pcie20>;
> > + status = "okay";
> > +};
> > +
> > +&pinctrl {
> > + bluetooth {
> > + bt_wake_gpio: bt-wake-pin {
> > + rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
> > + };
> > +
> > + bt_wake_host_irq: bt-wake-host-irq {
> > + rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_down>;
> > + };
> > + };
> > +
> > + usb {
> > + vcc5v0_otg_en: vcc5v0-otg-en {
> > + rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
> > + };
> > + };
> > +
> > + wlan {
> > + wifi_host_wake_irq: wifi-host-wake-irq {
> > + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
> > + };
> > + };
> > +};
> > +
> > +&pwm15 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pwm15m2_pins>;
> > + status = "okay";
> > +};
> > +
> > +&pwm2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pwm2m1_pins>;
> > + status = "okay";
> > +};
> > +
> > +&pwm3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pwm3m2_pins>;
> > + status = "okay";
> > +};
> > +
> > +&sdhci {
> > + status = "okay";
> > +};
> > +
> > +&sdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + bus-width = <4>;
> > + cap-sd-highspeed;
> > + cap-sdio-irq;
> > + keep-power-in-suspend;
> > + max-frequency = <150000000>;
> > + mmc-pwrseq = <&sdio_pwrseq>;
> > + no-mmc;
> > + no-sd;
> > + non-removable;
> > + sd-uhs-sdr104;
> > + status = "okay";
> > +
> > + ap6256: wifi@1 {
> > + compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
> > + reg = <1>;
> > + interrupt-names = "host-wake";
> > + interrupt-parent = <&gpio0>;
> > + interrupts = <RK_PA0 IRQ_TYPE_LEVEL_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&wifi_host_wake_irq>;
> > + };
> > +};
> > +
> > +&u2phy0_otg {
> > + phy-supply = <&vcc5v0_otg>;
> > +};
> > +
> > +&uart9 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart9m2_xfer &uart9m2_ctsn &uart9m2_rtsn>;
> > + uart-has-rtscts;
> > + status = "okay";
> > +
> > + bluetooth {
> > + compatible = "brcm,bcm4345c5";
> > + clocks = <&hym8563>;
> > + clock-names = "lpo";
> > + device-wakeup-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
> > + interrupt-names = "host-wakeup";
> > + interrupt-parent = <&gpio0>;
> > + interrupts = <RK_PC5 IRQ_TYPE_LEVEL_HIGH>;
> > + max-speed = <1500000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&bt_wake_host_irq &bt_wake_gpio>;
> > + shutdown-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
> > + vbat-supply = <&vcc_3v3_s3>;
> > + vddio-supply = <&vcc_1v8_s3>;
> > + };
> > +};
> > +
> > +&usb_host0_xhci {
> > + dr_mode = "host";
> > +};
> > +
> > +&usbdp_phy0 {
> > + rockchip,dp-lane-mux = <0 1>;
> > +};
> > --
> > 2.53.0
> >
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2026-03-10 2:39 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-03-06 2:46 [PATCH v3 0/3] Add support for Orange Pi 5 Pro dennis
2026-03-06 2:46 ` [PATCH v3 1/3] dt-bindings: arm: rockchip: Add " dennis
2026-03-06 2:46 ` [PATCH v3 2/3] arm64: dts: rockchip: refactor items from Orange Pi 5/b to prep for Pro dennis
2026-03-06 2:46 ` [PATCH v3 3/3] arm64: dts: rockchip: Add Orange Pi 5 Pro board support dennis
2026-03-06 3:28 ` Jimmy Hon
2026-03-10 2:39 ` Dennis Gilmore
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®