[PATCH v2] arm64: dts: qcom: eliza-evk: Add support for USB and SD card

[PATCH v2] arm64: dts: qcom: eliza-evk: Add support for USB and SD card

[Abel Vesa]

Even though the EVK comes with 3 Type-C ports, the Eliza EVK only has
one USB controller and a single set of PHYs, which are connected to
the port marked as JUSB.

Also, the EVK comes with an SD card slot.

So describe the PMIC GLINK node, the connector graph, the PHYs and repeater
supplies and enable the USB controller.

Also enable the second SD host controller, describe the card detect GPIO
and the board specific supplies.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
---
Changes in v2:
- Rebased on next-20260715.
- Picked up Konrad's R-b tag.
- Link to v1: https://patch.msgid.link/20260630-dts-qcom-eliza-cqs-evk-enable-usb-sdcard-v1-1-146264625095@oss.qualcomm.com
---
 arch/arm64/boot/dts/qcom/eliza-evk.dtsi | 92 +++++++++++++++++++++++++++++++++
 1 file changed, 92 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/eliza-evk.dtsi b/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
index e47b24f8b827..2fc945658300 100644
--- a/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
+++ b/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
@@ -11,6 +11,70 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	pmic-glink {
+		compatible = "qcom,eliza-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 122 GPIO_ACTIVE_HIGH>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&usb_dp_qmpphy_out>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&pm7550ba_eusb2_repeater {
+	vdd18-supply = <&vreg_l7b>;
+	vdd3-supply = <&vreg_l17b>;
+};
+
+&sdhc_2 {
+	vmmc-supply = <&vreg_l13b>;
+	vqmmc-supply = <&vreg_l23b>;
+
+	cd-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&sdc2_default>, <&sd_cd>;
+	pinctrl-1 = <&sdc2_sleep>, <&sd_cd>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+};
+
+&tlmm {
+	sd_cd: sd-cd-state {
+		pins = "gpio58";
+		function = "gpio";
+		bias-pull-up;
+	};
 };
 
 &uart13 {
@@ -18,3 +82,31 @@ &uart13 {
 
 	status = "okay";
 };
+
+&usb {
+	status = "okay";
+};
+
+&usb_dp_qmpphy {
+	vdda-phy-supply = <&vreg_l3g>;
+	vdda-pll-supply = <&vreg_l7k>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&usb_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_hsphy {
+	vdd-supply = <&vreg_l7k>;
+	vdda12-supply = <&vreg_l4b>;
+
+	phys = <&pm7550ba_eusb2_repeater>;
+
+	status = "okay";
+};

---
base-commit: b8809969e1d7a591e0f49dd464a5d04b3cf02ab1
change-id: 20260630-dts-qcom-eliza-cqs-evk-enable-usb-sdcard-e774d12eb516

Best regards,
--  
Abel Vesa <abel.vesa@oss.qualcomm.com>