mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
* [PATCH v2 0/3] Enable quad SPI mode for SPI-NAND on IPQ RDP boards
@ 2026-08-07 16:35 Md Sadre Alam
  2026-08-07 16:35 ` [PATCH v2 1/3] arm64: dts: qcom: ipq9574-rdp-common: Enable quad SPI mode for SPI-NAND Md Sadre Alam
                   ` (3 more replies)
  0 siblings, 4 replies; 5+ messages in thread
From: Md Sadre Alam @ 2026-08-07 16:35 UTC (permalink / raw)
  To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley
  Cc: linux-arm-msm, devicetree, linux-kernel, Md Sadre Alam, Konrad Dybcio

Several Qualcomm IPQ RDP platforms support quad (x4) SPI transfers
between the QPIC SPI-NAND controller and the attached SPI-NAND device.
However, the corresponding device trees do not currently describe the
bus width capabilities of the flash device, causing transfers to fall
back to the default single-bit (x1) mode.

This series enables quad SPI operation on supported IPQ reference
design platforms by adding spi-rx-bus-width and spi-tx-bus-width
properties to the SPI-NAND device nodes.

The series updates the IPQ9574, IPQ5424 and IPQ5332 based RDPs.

Signed-off-by: Md Sadre Alam <md.alam@oss.qualcomm.com>
---
Changes in v2:
- No code changes
- Pick R-b tags
- rebased on top of tree
- updated the dependecies
- Depends-on : https://lore.kernel.org/linux-arm-msm/20260807-quad-v2-0-8ec821e2f22b@oss.qualcomm.com/
- Link to v1: https://lore.kernel.org/r/20260716-quad_dts-v1-0-74d86792944a@oss.qualcomm.com

---
Md Sadre Alam (3):
      arm64: dts: qcom: ipq9574-rdp-common: Enable quad SPI mode for SPI-NAND
      arm64: dts: qcom: ipq5424-rdp466: Enable quad SPI mode for SPI-NAND
      arm64: dts: qcom: ipq5332-rdp-common: Enable quad SPI mode for SPI-NAND

 arch/arm64/boot/dts/qcom/ipq5332-rdp-common.dtsi | 2 ++
 arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts      | 2 ++
 arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi | 2 ++
 3 files changed, 6 insertions(+)
---
base-commit: d56fa0b2bd2d9b2fddc10e8f5bdd42d56676935c
change-id: 20260716-quad_dts-6bac0484c08c
prerequisite-message-id : 20260807-quad-v2-0-8ec821e2f22b@oss.qualcomm.com
prerequisite-patch-id: 912ede01168ddf0476ba69ab0db786186073f817
prerequisite-patch-id: ab86c050f49d3180b10e61ec20bdcc6272c8100c
prerequisite-patch-id: 932ca3dc3893df6de25928b24c7c24550907088d

Best regards,
-- 
Md Sadre Alam <md.alam@oss.qualcomm.com>


^ permalink raw reply	[flat|nested] 5+ messages in thread

* [PATCH v2 1/3] arm64: dts: qcom: ipq9574-rdp-common: Enable quad SPI mode for SPI-NAND
  2026-08-07 16:35 [PATCH v2 0/3] Enable quad SPI mode for SPI-NAND on IPQ RDP boards Md Sadre Alam
@ 2026-08-07 16:35 ` Md Sadre Alam
  2026-08-07 16:35 ` [PATCH v2 2/3] arm64: dts: qcom: ipq5424-rdp466: " Md Sadre Alam
                   ` (2 subsequent siblings)
  3 siblings, 0 replies; 5+ messages in thread
From: Md Sadre Alam @ 2026-08-07 16:35 UTC (permalink / raw)
  To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley
  Cc: linux-arm-msm, devicetree, linux-kernel, Md Sadre Alam, Konrad Dybcio

Set the SPI-NAND device node to use 4-bit transmit and receive bus widths.

The board supports quad SPI transfers, but the device tree currently does
not describe the wider bus. Add spi-tx-bus-width and spi-rx-bus-width so
the controller and flash can use quad mode instead of single-bit transfers.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <md.alam@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi b/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
index 62877b46f9b3..86138529ba77 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi
@@ -249,6 +249,8 @@ flash@0 {
 		nand-ecc-engine = <&qpic_nand>;
 		nand-ecc-strength = <4>;
 		nand-ecc-step-size = <512>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
 	};
 };
 

-- 
2.34.1


^ permalink raw reply	[flat|nested] 5+ messages in thread

* [PATCH v2 2/3] arm64: dts: qcom: ipq5424-rdp466: Enable quad SPI mode for SPI-NAND
  2026-08-07 16:35 [PATCH v2 0/3] Enable quad SPI mode for SPI-NAND on IPQ RDP boards Md Sadre Alam
  2026-08-07 16:35 ` [PATCH v2 1/3] arm64: dts: qcom: ipq9574-rdp-common: Enable quad SPI mode for SPI-NAND Md Sadre Alam
@ 2026-08-07 16:35 ` Md Sadre Alam
  2026-08-07 16:35 ` [PATCH v2 3/3] arm64: dts: qcom: ipq5332-rdp-common: " Md Sadre Alam
  2026-09-29  3:15 ` [PATCH v2 0/3] Enable quad SPI mode for SPI-NAND on IPQ RDP boards Bjorn Andersson
  3 siblings, 0 replies; 5+ messages in thread
From: Md Sadre Alam @ 2026-08-07 16:35 UTC (permalink / raw)
  To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley
  Cc: linux-arm-msm, devicetree, linux-kernel, Md Sadre Alam, Konrad Dybcio

Enable quad SPI transfers for the SPI-NAND device by setting both spi-rx-
bus-width and spi-tx-bus-width to 4.

Without these properties, the device uses the default single-bit bus width.
Configure the board to use 4-bit read and write transfers so the controller
and flash can operate in quad SPI mode.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <md.alam@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts b/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts
index be8657239c46..793afc3ee82e 100644
--- a/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts
+++ b/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts
@@ -261,6 +261,8 @@ flash@0 {
 		nand-ecc-engine = <&qpic_nand>;
 		nand-ecc-strength = <4>;
 		nand-ecc-step-size = <512>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
 	};
 };
 

-- 
2.34.1


^ permalink raw reply	[flat|nested] 5+ messages in thread

* [PATCH v2 3/3] arm64: dts: qcom: ipq5332-rdp-common: Enable quad SPI mode for SPI-NAND
  2026-08-07 16:35 [PATCH v2 0/3] Enable quad SPI mode for SPI-NAND on IPQ RDP boards Md Sadre Alam
  2026-08-07 16:35 ` [PATCH v2 1/3] arm64: dts: qcom: ipq9574-rdp-common: Enable quad SPI mode for SPI-NAND Md Sadre Alam
  2026-08-07 16:35 ` [PATCH v2 2/3] arm64: dts: qcom: ipq5424-rdp466: " Md Sadre Alam
@ 2026-08-07 16:35 ` Md Sadre Alam
  2026-09-29  3:15 ` [PATCH v2 0/3] Enable quad SPI mode for SPI-NAND on IPQ RDP boards Bjorn Andersson
  3 siblings, 0 replies; 5+ messages in thread
From: Md Sadre Alam @ 2026-08-07 16:35 UTC (permalink / raw)
  To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley
  Cc: linux-arm-msm, devicetree, linux-kernel, Md Sadre Alam, Konrad Dybcio

The SPI-NAND device on the IPQ5332 RDP supports 4-bit data transfers, but
the device tree does not describe the bus width, so transfers use the
default single-bit mode.

Set spi-rx-bus-width and spi-tx-bus-width to 4 to enable quad read and
write transfers and improve SPI-NAND throughput.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <md.alam@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/ipq5332-rdp-common.dtsi | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/ipq5332-rdp-common.dtsi b/arch/arm64/boot/dts/qcom/ipq5332-rdp-common.dtsi
index 3bbf748f2e5c..6f5b193a204b 100644
--- a/arch/arm64/boot/dts/qcom/ipq5332-rdp-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5332-rdp-common.dtsi
@@ -141,5 +141,7 @@ flash@0 {
 		nand-ecc-engine = <&qpic_nand>;
 		nand-ecc-strength = <4>;
 		nand-ecc-step-size = <512>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
 	};
 };

-- 
2.34.1


^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: [PATCH v2 0/3] Enable quad SPI mode for SPI-NAND on IPQ RDP boards
  2026-08-07 16:35 [PATCH v2 0/3] Enable quad SPI mode for SPI-NAND on IPQ RDP boards Md Sadre Alam
                   ` (2 preceding siblings ...)
  2026-08-07 16:35 ` [PATCH v2 3/3] arm64: dts: qcom: ipq5332-rdp-common: " Md Sadre Alam
@ 2026-09-29  3:15 ` Bjorn Andersson
  3 siblings, 0 replies; 5+ messages in thread
From: Bjorn Andersson @ 2026-09-29  3:15 UTC (permalink / raw)
  To: Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
	Md Sadre Alam
  Cc: linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio


On Fri, 07 Aug 2026 22:05:30 +0530, Md Sadre Alam wrote:
> Several Qualcomm IPQ RDP platforms support quad (x4) SPI transfers
> between the QPIC SPI-NAND controller and the attached SPI-NAND device.
> However, the corresponding device trees do not currently describe the
> bus width capabilities of the flash device, causing transfers to fall
> back to the default single-bit (x1) mode.
> 
> This series enables quad SPI operation on supported IPQ reference
> design platforms by adding spi-rx-bus-width and spi-tx-bus-width
> properties to the SPI-NAND device nodes.
> 
> [...]

Applied, thanks!

[1/3] arm64: dts: qcom: ipq9574-rdp-common: Enable quad SPI mode for SPI-NAND
      commit: 1f6925d80ae327ab4e18e21b7c87c57b793c462c
[2/3] arm64: dts: qcom: ipq5424-rdp466: Enable quad SPI mode for SPI-NAND
      commit: 4d36e6d8c5a489c85d9440fc7330beee9b74f6f0
[3/3] arm64: dts: qcom: ipq5332-rdp-common: Enable quad SPI mode for SPI-NAND
      commit: be63397b43a4b1b3c4fbdb149413dacd8ad5a844

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>

^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, other threads:[~2026-09-29  3:16 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-08-07 16:35 [PATCH v2 0/3] Enable quad SPI mode for SPI-NAND on IPQ RDP boards Md Sadre Alam
2026-08-07 16:35 ` [PATCH v2 1/3] arm64: dts: qcom: ipq9574-rdp-common: Enable quad SPI mode for SPI-NAND Md Sadre Alam
2026-08-07 16:35 ` [PATCH v2 2/3] arm64: dts: qcom: ipq5424-rdp466: " Md Sadre Alam
2026-08-07 16:35 ` [PATCH v2 3/3] arm64: dts: qcom: ipq5332-rdp-common: " Md Sadre Alam
2026-09-29  3:15 ` [PATCH v2 0/3] Enable quad SPI mode for SPI-NAND on IPQ RDP boards Bjorn Andersson

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®