[PATCH v2 0/2] arm64: dts: rockchip: Add MangoPi M28K

[PATCH v2 0/2] arm64: dts: rockchip: Add MangoPi M28K

[Chukun Pan]

Information about the MangoPi M28K is here: https://widora.cn/m28k

MangoPi also has a version called "M28K Pro", which replaces the
RTL8111H with the RTL8125B.

Changes in v2:
- Add USB 2.0 support
- Remove merged patch

Chukun Pan (2):
  dt-bindings: arm: rockchip: Add MangoPi M28K
  arm64: dts: rockchip: Add MangoPi M28K

 .../devicetree/bindings/arm/rockchip.yaml     |   5 +
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3528-mangopi-m28k.dts | 412 ++++++++++++++++++
 3 files changed, 418 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3528-mangopi-m28k.dts

-- 
2.34.1

[PATCH v2 1/2] dt-bindings: arm: rockchip: Add MangoPi M28K

[Chukun Pan]

The MangoPi M28K is a dual-gigabit SBC developed by Widora based
on the RK3528 SoC. Add devicetree binding documentation for it.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
---
 Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index aa66a15be233..45fee0c5076a 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -803,6 +803,11 @@ properties:
               - lunzn,fastrhino-r68s
           - const: rockchip,rk3568
 
+      - description: MangoPi M28K
+        items:
+          - const: widora,mangopi-m28k
+          - const: rockchip,rk3528
+
       - description: mqmaker MiQi
         items:
           - const: mqmaker,miqi
-- 
2.34.1

[PATCH v2 2/2] arm64: dts: rockchip: Add MangoPi M28K

[Chukun Pan]

The MangoPi M28K is a development board with the
Rockchip RK3528 SoC. It has the following features:

- 2x USB 2.0
- 1x mini-HDMI
- 1/2/4GB LPDDR4
- AIC8800 WiFi/BT
- MicroSD card slot
- Optional 16/32GB eMMC
- 1x 1GbE RTL8111H Ethernet
- 1x 1GbE RTL8211F Ethernet

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3528-mangopi-m28k.dts | 412 ++++++++++++++++++
 2 files changed, 413 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3528-mangopi-m28k.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 519bb6c431ac..926ff7a30c49 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399pro-rock-pi-n10.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3528-armsom-sige1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3528-hinlink-h28k.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3528-mangopi-m28k.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3528-nanopi-zero2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3528-radxa-e20c.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3528-rock-2a.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3528-mangopi-m28k.dts b/arch/arm64/boot/dts/rockchip/rk3528-mangopi-m28k.dts
new file mode 100644
index 000000000000..3d53d9dfb20f
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3528-mangopi-m28k.dts
@@ -0,0 +1,412 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "rk3528.dtsi"
+
+/ {
+	model = "MangoPi M28K";
+	compatible = "widora,mangopi-m28k", "rockchip,rk3528";
+
+	aliases {
+		ethernet0 = &gmac1;
+		i2c6 = &i2c6;
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc;
+		mmc2 = &sdio0;
+		serial0 = &uart0;
+		serial2 = &uart2;
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:1500000n8";
+	};
+
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm3_m0_ir_rx>;
+	};
+
+	keys-0 {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <100>;
+
+		button-boot {
+			label = "BOOT";
+			linux,code = <KEY_SETUP>;
+			press-threshold-microvolt = <0>;
+		};
+	};
+
+	keys-1 {
+		compatible = "adc-keys";
+		io-channels = <&saradc 1>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <100>;
+
+		button-recover {
+			label = "RECOVER";
+			linux,code = <KEY_VENDOR>;
+			press-threshold-microvolt = <0>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&lan_led>, <&wan_led>, <&work_led>;
+
+		led-0 {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_LAN;
+			gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "netdev";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_WAN;
+			gpios = <&gpio4 RK_PC0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "netdev";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio4 RK_PB7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	vdd_0v9: regulator-0v9-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_0v9";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_ddr: regulator-1v1-vcc-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_ddr";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_1v8: regulator-1v8-vcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
+	vcc_3v3: regulator-3v3-vcc {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc3v3_sd: regulator-3v3-vcc-sd {
+		compatible = "regulator-fixed";
+		gpios = <&gpio4 RK_PA1 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwren_l>;
+		regulator-name = "vcc3v3_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
+	vcc_sys: regulator-5v0-vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vccio_sd: regulator-vccio-sd {
+		compatible = "regulator-gpio";
+		gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_vol_ctrl_h>;
+		regulator-name = "vccio_sd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		states = <1800000 0x0>, <3300000 0x1>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vdd_arm: regulator-vdd-arm {
+		compatible = "pwm-regulator";
+		pwms = <&pwm1 0 5000 PWM_POLARITY_INVERTED>;
+		pwm-supply = <&vcc_sys>;
+		regulator-name = "vdd_arm";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <746000>;
+		regulator-max-microvolt = <1201000>;
+		regulator-settling-time-up-us = <250>;
+	};
+
+	vdd_logic: regulator-vdd-logic {
+		compatible = "pwm-regulator";
+		pwms = <&pwm2 0 5000 PWM_POLARITY_INVERTED>;
+		pwm-supply = <&vcc_sys>;
+		regulator-name = "vdd_logic";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <705000>;
+		regulator-max-microvolt = <1006000>;
+		regulator-settling-time-up-us = <250>;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_reg_on_h>;
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <5000000>;
+		reset-gpios = <&gpio1 RK_PA6 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&combphy {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&gmac1 {
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_miim>,
+		    <&rgmii_tx_bus2>,
+		    <&rgmii_rx_bus2>,
+		    <&rgmii_rgmii_clk>,
+		    <&rgmii_rgmii_bus>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_logic>;
+	status = "okay";
+};
+
+&i2c6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c6m0_xfer>;
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gmac1_rstn_l>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rtl8111hs_isolateb_l>;
+	reset-gpios = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&pinctrl {
+	gmac {
+		gmac1_rstn_l: gmac1-rstn-l {
+			rockchip,pins = <4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	ir {
+		pwm3_m0_ir_rx: pwm3-m0-ir-rx {
+			rockchip,pins = <4 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	leds {
+		lan_led: lan-led {
+			rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		wan_led: wan-led {
+			rockchip,pins = <4 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		work_led: work-led {
+			rockchip,pins = <4 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		rtl8111hs_isolateb_l: rtl8111hs-isolateb-l {
+			rockchip,pins = <4 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_pwren_l: sdmmc-pwren-l {
+			rockchip,pins = <4 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		sdmmc_vol_ctrl_h: sdmmc-vol-ctrl-h {
+			rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	wifi {
+		wifi_reg_on_h: wifi-reg-on-h {
+			rockchip,pins = <1 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		wifi_wake_host_h: wifi-wake-host-h {
+			rockchip,pins = <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm1m0_pins>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm2m0_pins>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdio0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	disable-wp;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0m0_xfer>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2m1_ctsn>, <&uart2m1_rtsn>, <&uart2m1_xfer>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3m0_xfer>;
+	status = "disabled";
+};
+
+&usb2phy {
+	status = "okay";
+};
+
+&usb2phy_host {
+	phy-supply = <&vcc_sys>;
+	status = "okay";
+};
+
+&usb2phy_otg {
+	phy-supply = <&vcc_sys>;
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+	extcon = <&usb2phy>;
+	maximum-speed = "high-speed";
+	phys = <&usb2phy_otg>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
-- 
2.34.1

Re: [PATCH v2 1/2] dt-bindings: arm: rockchip: Add MangoPi M28K

[Krzysztof Kozlowski]

On Sat, Aug 01, 2026 at 04:00:17PM +0800, Chukun Pan wrote:
> The MangoPi M28K is a dual-gigabit SBC developed by Widora based
> on the RK3528 SoC. Add devicetree binding documentation for it.
> 
> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>

How did you resolve my comments from v1? You split patches instead of
squashing and removed any explanation I asked for.

Best regards,
Krzysztof

Re: [PATCH v2 1/2] dt-bindings: arm: rockchip: Add MangoPi M28K

[Chukun Pan]

Hi,

> How did you resolve my comments from v1? You split patches instead of
> squashing and removed any explanation I asked for.

My idea is to add an official product link to differentiate them.
HINLINK H28K has this link, which I added to the commit message.
As for MangoPi, since it's discontinued, there's no product link
available. I will include a link to an image of the board in the
next patch to show that they are different boards.

Does this solve your problem?

Thanks,
Chukun

Re: [PATCH v2 1/2] dt-bindings: arm: rockchip: Add MangoPi M28K

[Krzysztof Kozlowski]

On 04/08/2026 08:40, Chukun Pan wrote:
> Hi,
> 
>> How did you resolve my comments from v1? You split patches instead of
>> squashing and removed any explanation I asked for.
> 
> My idea is to add an official product link to differentiate them.
> HINLINK H28K has this link, which I added to the commit message.
> As for MangoPi, since it's discontinued, there's no product link
> available. I will include a link to an image of the board in the
> next patch to show that they are different boards.
> 
> Does this solve your problem?

I asked you to squash the patches, to avoid work. Instead, you split the
patchsets giving us more work.

Best regards,
Krzysztof

Re: [PATCH v2 1/2] dt-bindings: arm: rockchip: Add MangoPi M28K

[Chukun Pan]

Hi,

> I asked you to squash the patches, to avoid work. Instead, you split the
> patchsets giving us more work.

Sorry, I forgot about that. I should check the previous comments before
posting. The patch for HINLINK H28K has been merged. Should I update this
series? Sorry for giving you more work.

Thanks,
Chukun

Re: [PATCH v2 1/2] dt-bindings: arm: rockchip: Add MangoPi M28K

[Krzysztof Kozlowski]

On Sat, Aug 01, 2026 at 04:00:17PM +0800, Chukun Pan wrote:
> The MangoPi M28K is a dual-gigabit SBC developed by Widora based
> on the RK3528 SoC. Add devicetree binding documentation for it.
> 
> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
> ---
>  Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
>  1 file changed, 5 insertions(+)

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

Re: [PATCH v2 2/2] arm64: dts: rockchip: Add MangoPi M28K

[Andrey Korshunov]

On Sat, 1 Aug 2026 16:00:18 +0800, Chukun Pan wrote:
> The MangoPi M28K is a development board with the
> Rockchip RK3528 SoC. It has the following features:

Tested on a MangoPi M28K v1.1 (non-Pro, 4 GB, no eMMC module) booting
from microSD, with this patch applied to OpenWrt's 6.18.44 kernel and
U-Boot 2026.07 built with a board target for the M28K.

Both GbE ports work (RTL8211F on gmac1, RTL8111H on PCIe), as do the
LAN and WAN LEDs and both USB 2.0 ports. With the same devicetree on a
6.12 kernel, the AIC8800D80 on sdio0 also comes up with the out-of-tree
driver.

Tested-by: Andrey Korshunov <razor1702@gmail.com>