[PATCH net-next v8 00/11] net: pcs: add basic support for RK3568 XPCS

[PATCH net-next v8 00/11] net: pcs: add basic support for RK3568 XPCS

[Coia Prant]

This series adds proper SGMII support for the Rockchip RK3568 SoC
using the integrated Synopsys DesignWare XPCS, along with necessary
fixes and refactoring in the stmmac core and XPCS driver.

Motivation
==========
The RK3568 integrates a DW XPCS accessed via APB3 and connected to
a Naneng Combo SerDes PHY.  Several boards (e.g., Ariaboard
Photonicat) use this interface for Gigabit Ethernet.  However, the
current upstream stmmac driver does not support this configuration,
and the XPCS driver has issues in SGMII poll mode that cause the
link to be reported incorrectly.

This series addresses these issues by:
- Refactoring stmmac PCS lifetime management to allow platform drivers
  full control over PCS creation/destruction
- Fixing the XPCS driver's SGMII link recovery
- Adding a Rockchip XPCS platform glue driver and wiring it up in
  dwmac-rk

Series overview
===============

Generic:
  Patch 1: move XPCS lifetime management to platform drivers

PHY:
  Patch 2: DT binding for Naneng Combo PHY SGMII MAC selection
  Patch 3: implement the PHY SGMII MAC selection in driver

RK3568 XPCS/SGMII:
  Patch 4: DT binding for Rockchip RK3568 XPCS
  Patch 5: add XPCS and fixed-clock nodes to rk3568.dtsi
  Patch 6: add ANRESTART support for SGMII link recovery
  Patch 7: implement the Rockchip XPCS platform glue driver
  Patch 8: DT binding for Rockchip DWMAC PCS
  Patch 9: wire up SGMII support in dwmac-rk
  Patch 11: update MAINTAINERS

Board enablement:
  Patch 10: enable SGMII LAN port on Photonicat board

Changelog
=========

Changes since v7:

Patch 7 (net: pcs: xpcs: add Rockchip RK3568 platform glue driver)
- Fix a use-after-free window in xpcs_rk_create(): device_link_add()
  does not fail on a supplier that is unbinding (it creates the link in
  DL_STATE_SUPPLIER_UNBIND), so the drvdata could be freed between the
  link creation and the platform_get_drvdata() call. Read the drvdata
  under the supplier's device_lock with a device_is_bound() check, so
  a concurrent unbind is detected and the probe defers.
- Correct the comment above device_link_add(): the link does not keep
  the supplier alive by itself; device_lock() plus device_is_bound() is
  what protects the drvdata read.
- Change the Kconfig select to "select PM_GENERIC_DOMAINS if PM" so a
  COMPILE_TEST build with CONFIG_PM=n does not force PM_GENERIC_DOMAINS
  on against its own dependency.

Key design decisions
====================
- The stmmac core now delegates XPCS creation entirely to platform
  drivers via pcs_init/pcs_exit.  This is necessary because the
  generic XPCS creation logic would override any XPCS set up by the
  platform driver.

- The Rockchip XPCS driver creates a virtual MDIO bus over the APB3
  registers and implements address remapping.  The generic XPCS core
  handles all PCS configuration via phylink_pcs_ops.

- On RK3568 in SGMII mode, the MAC clock is fixed at 125 MHz and
  cannot be dynamically changed.  In-band mode is used, and the
  generic stmmac set_clk_tx_rate callback is disabled to prevent
  incorrect clock updates that would break RX.

- The SerDes and power domain are attached to the XPCS device tree
  node rather than the MAC node. This reflects the actual hardware
  topology and simplifies the dwmac-rk driver by keeping all PCS-related
  resources self-contained. It also prepares for possible future QSGMII
  support, where a single SerDes serves multiple MACs and would be
  more naturally managed under the XPCS node.

Testing
=======
Board: Ariaboard Photonicat (RK3568)
OS: Armbian (trixie)
Kernel: 6.18 (backports)
Result: The SGMII interface obtains an IP address, SSH works, and
        ping traffic passes without loss.

Notes
=====
- When testing out-band mode with set_clk_tx_rate, only 1000Mbps
  works on both TX/RX; 10/100Mbps only works on TX side.

Dependencies
============
None. All patches apply cleanly on top of torvalds master tree (v7.3).

Acknowledgments
===============
This work was inspired by and builds upon the excellent work of others:
- Serge Semin's Synopsys DesignWare XPCS platform driver (pcs-xpcs-plat.c)
- Clément Léger's Renesas MIIC driver (pcs-rzn1-miic.c)
- The Rockchip TRM and downstream OEM drivers

Thanks in advance,
Coia Prant
---
Coia Prant (11):
  net: stmmac: move XPCS lifetime management to platform drivers
  dt-bindings: phy: rockchip: naneng-combphy: add rockchip,sgmii-mac-sel
    property
  phy: rockchip: naneng-combphy: add SGMII MAC selection for RK3568
  dt-bindings: net: pcs: add rockchip,rk3568-xpcs support
  arm64: dts: rockchip: rk3568: add XPCS and fixed-clock nodes
  net: pcs: xpcs: add ANRESTART support for SGMII link recovery
  net: pcs: xpcs: add Rockchip RK3568 platform glue driver
  dt-bindings: net: rockchip-dwmac: document pcs-handle
  net: stmmac: dwmac-rk: add SGMII support for RK3568
  arm64: dts: rockchip: rk3568-photonicat: enable SGMII LAN port
  MAINTAINERS: add entry for Rockchip XPCS driver

 .../net/pcs/rockchip,rk3568-xpcs.yaml         | 110 ++++
 .../bindings/net/rockchip-dwmac.yaml          |  18 +
 .../phy/phy-rockchip-naneng-combphy.yaml      |  13 +
 MAINTAINERS                                   |   9 +
 .../boot/dts/rockchip/rk3568-photonicat.dts   |  74 ++-
 arch/arm64/boot/dts/rockchip/rk3568.dtsi      |  45 ++
 drivers/net/ethernet/stmicro/stmmac/Kconfig   |   1 +
 .../net/ethernet/stmicro/stmmac/dwmac-intel.c |  44 +-
 .../stmicro/stmmac/dwmac-renesas-gbeth.c      |   7 +-
 .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 130 +++-
 .../net/ethernet/stmicro/stmmac/dwmac-rzn1.c  |   7 +-
 .../ethernet/stmicro/stmmac/dwmac-socfpga.c   |   7 +-
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c |  39 +-
 drivers/net/pcs/Kconfig                       |  25 +
 drivers/net/pcs/Makefile                      |   5 +-
 drivers/net/pcs/pcs-xpcs-rk.c                 | 599 ++++++++++++++++++
 drivers/net/pcs/pcs-xpcs.c                    |  35 +-
 .../rockchip/phy-rockchip-naneng-combphy.c    |   8 +
 include/linux/pcs/pcs-xpcs-rk.h               |  11 +
 19 files changed, 1115 insertions(+), 72 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/pcs/rockchip,rk3568-xpcs.yaml
 create mode 100644 drivers/net/pcs/pcs-xpcs-rk.c
 create mode 100644 include/linux/pcs/pcs-xpcs-rk.h

-- 
2.47.3

[PATCH net-next v8 01/11] net: stmmac: move XPCS lifetime management to platform drivers

[Coia Prant]

The current XPCS creation logic in stmmac_pcs_setup() is problematic
for several reasons.

First, if a device tree specifies a "pcs-handle" but no select_pcs()
callback is provided by the platform driver, the created XPCS cannot be
used by phylink for PCS operations. The framework requires select_pcs()
to return the PCS to the core, so the pcs-handle property becomes
effectively useless for link management without the matching callback.
The XPCS is still consulted by stmmac_phylink_setup() and
stmmac_init_phy(), which makes the configuration silently half-working
rather than clearly broken.

Second, and more critically, when a platform driver sets pcs_init()
and creates an XPCS inside that callback, the common code afterwards
still runs unconditionally and overwrites priv->hw->xpcs with the
local xpcs variable, which stays NULL. The platform driver has no way
to prevent this override because the common code runs after the
platform-specific initialization.

After commit 93f84152e4ae ("net: stmmac: clean up
stmmac_mac_select_pcs()"), the common code no longer falls back to
priv->hw->phylink_pcs if select_pcs() is not set. This change
reinforces that each platform must manage its own PCS life cycle
explicitly, but the XPCS creation code in stmmac_pcs_setup() was not
updated to match this new expectation, leaving a gap where platform
drivers have no clean way to take control of XPCS creation.

Address all of these issues by simplifying the existing pcs_init() and
pcs_exit() dispatch in stmmac_pcs_setup() and stmmac_pcs_clean(). The
common stmmac_pcs_setup() now calls plat->pcs_init() if present, and
stmmac_pcs_clean() calls plat->pcs_exit() if present, removing the
confusing and error-prone XPCS creation logic from the common code.

Platforms that do not need an XPCS simply leave the callbacks as NULL
and no change in behavior occurs. Platforms that do need an XPCS can
now create it with the exact configuration they require, including
wrapping it with custom phylink_pcs_ops when necessary.

Note that this also removes the generic "pcs-handle" parsing from the
common code. A glue that does not set pcs_init() now leaves
priv->hw->xpcs as NULL, and "pcs-handle" becomes a no-op for it. No
in-tree platform relies on this path: every DTS that pairs a dwmac node
with a PCS goes through a glue that sets pcs_init() (Intel, Renesas,
RZ/N1, SoCFPGA, Rockchip).

The Intel mGbE glue is updated to create its XPCS inside its own
pcs_init() implementation, and the renesas-gbeth, rzn1 and socfpga
pcs_exit() callbacks now explicitly clear priv->hw->phylink_pcs after
destroying the PCS to avoid dangling pointer references.

Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 .../net/ethernet/stmicro/stmmac/dwmac-intel.c | 44 +++++++++++++++++--
 .../stmicro/stmmac/dwmac-renesas-gbeth.c      |  7 ++-
 .../net/ethernet/stmicro/stmmac/dwmac-rzn1.c  |  7 ++-
 .../ethernet/stmicro/stmmac/dwmac-socfpga.c   |  7 ++-
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c | 39 +++-------------
 5 files changed, 62 insertions(+), 42 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
index f5f9fa67ecd77..4308dccbf2570 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c
@@ -603,13 +603,47 @@ static void common_default_data(struct plat_stmmacenet_data *plat)
 	plat->mdio_bus_data->needs_reset = true;
 }
 
+static int intel_mgbe_pcs_init(struct stmmac_priv *priv)
+{
+	struct fwnode_handle *devnode, *pcsnode;
+	struct dw_xpcs *xpcs;
+	int addr;
+
+	devnode = dev_fwnode(priv->device);
+
+	if (fwnode_property_present(devnode, "pcs-handle")) {
+		pcsnode = fwnode_find_reference(devnode, "pcs-handle", 0);
+		xpcs = xpcs_create_fwnode(pcsnode);
+		fwnode_handle_put(pcsnode);
+	} else {
+		addr = ffs(priv->plat->mdio_bus_data->pcs_mask) - 1;
+		xpcs = xpcs_create_mdiodev(priv->mii, addr);
+	}
+
+	if (IS_ERR(xpcs))
+		return PTR_ERR(xpcs);
+
+	xpcs_config_eee_mult_fact(xpcs, priv->plat->mult_fact_100ns);
+
+	priv->hw->xpcs = xpcs;
+	return 0;
+}
+
+static void intel_mgbe_pcs_exit(struct stmmac_priv *priv)
+{
+	if (!priv->hw->xpcs)
+		return;
+
+	xpcs_destroy(priv->hw->xpcs);
+	priv->hw->xpcs = NULL;
+}
+
 static struct phylink_pcs *intel_mgbe_select_pcs(struct stmmac_priv *priv,
 						 phy_interface_t interface)
 {
-	/* plat->mdio_bus_data->has_xpcs has been set true, so there
-	 * should always be an XPCS. The original code would always
-	 * return this if present.
-	 */
+	if (!priv->hw->xpcs)
+		return NULL;
+
 	return xpcs_to_phylink_pcs(priv->hw->xpcs);
 }
 
@@ -733,6 +767,8 @@ static int intel_mgbe_common_data(struct pci_dev *pdev,
 	    plat->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
 		plat->mdio_bus_data->pcs_mask = BIT_U32(INTEL_MGBE_XPCS_ADDR);
 		plat->default_an_inband = true;
+		plat->pcs_init = intel_mgbe_pcs_init;
+		plat->pcs_exit = intel_mgbe_pcs_exit;
 		plat->select_pcs = intel_mgbe_select_pcs;
 	}
 
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-renesas-gbeth.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-renesas-gbeth.c
index 19f34e18bfef2..9af32c26f9c14 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-renesas-gbeth.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-renesas-gbeth.c
@@ -81,8 +81,11 @@ static int renesas_gmac_pcs_init(struct stmmac_priv *priv)
 
 static void renesas_gmac_pcs_exit(struct stmmac_priv *priv)
 {
-	if (priv->hw->phylink_pcs)
-		miic_destroy(priv->hw->phylink_pcs);
+	if (!priv->hw->phylink_pcs)
+		return;
+
+	miic_destroy(priv->hw->phylink_pcs);
+	priv->hw->phylink_pcs = NULL;
 }
 
 static struct phylink_pcs *renesas_gmac_select_pcs(struct stmmac_priv *priv,
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c
index 13634965bc19a..01df4776edb3f 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rzn1.c
@@ -35,8 +35,11 @@ static int rzn1_dwmac_pcs_init(struct stmmac_priv *priv)
 
 static void rzn1_dwmac_pcs_exit(struct stmmac_priv *priv)
 {
-	if (priv->hw->phylink_pcs)
-		miic_destroy(priv->hw->phylink_pcs);
+	if (!priv->hw->phylink_pcs)
+		return;
+
+	miic_destroy(priv->hw->phylink_pcs);
+	priv->hw->phylink_pcs = NULL;
 }
 
 static struct phylink_pcs *rzn1_dwmac_select_pcs(struct stmmac_priv *priv,
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
index 1d7f0a57d2889..6d4bc1fe8f751 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c
@@ -539,8 +539,11 @@ static int socfpga_dwmac_pcs_init(struct stmmac_priv *priv)
 
 static void socfpga_dwmac_pcs_exit(struct stmmac_priv *priv)
 {
-	if (priv->hw->phylink_pcs)
-		lynx_pcs_destroy(priv->hw->phylink_pcs);
+	if (!priv->hw->phylink_pcs)
+		return;
+
+	lynx_pcs_destroy(priv->hw->phylink_pcs);
+	priv->hw->phylink_pcs = NULL;
 }
 
 static struct phylink_pcs *socfpga_dwmac_select_pcs(struct stmmac_priv *priv,
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
index afe98ff5bdcb0..7396b68899c66 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
@@ -426,35 +426,14 @@ int stmmac_mdio_reset(struct mii_bus *bus)
 int stmmac_pcs_setup(struct net_device *ndev)
 {
 	struct stmmac_priv *priv = netdev_priv(ndev);
-	struct fwnode_handle *devnode, *pcsnode;
-	struct dw_xpcs *xpcs = NULL;
-	int addr, ret;
-
-	devnode = dev_fwnode(priv->device);
-
-	if (priv->plat->pcs_init) {
-		ret = priv->plat->pcs_init(priv);
-	} else if (fwnode_property_present(devnode, "pcs-handle")) {
-		pcsnode = fwnode_find_reference(devnode, "pcs-handle", 0);
-		xpcs = xpcs_create_fwnode(pcsnode);
-		fwnode_handle_put(pcsnode);
-		ret = PTR_ERR_OR_ZERO(xpcs);
-	} else if (priv->plat->mdio_bus_data &&
-		   priv->plat->mdio_bus_data->pcs_mask) {
-		addr = ffs(priv->plat->mdio_bus_data->pcs_mask) - 1;
-		xpcs = xpcs_create_mdiodev(priv->mii, addr);
-		ret = PTR_ERR_OR_ZERO(xpcs);
-	} else {
+	int ret;
+
+	if (!priv->plat->pcs_init)
 		return 0;
-	}
 
+	ret = priv->plat->pcs_init(priv);
 	if (ret)
-		return dev_err_probe(priv->device, ret, "No xPCS found\n");
-
-	if (xpcs)
-		xpcs_config_eee_mult_fact(xpcs, priv->plat->mult_fact_100ns);
-
-	priv->hw->xpcs = xpcs;
+		return dev_err_probe(priv->device, ret, "Failed to initialize PCS\n");
 
 	return 0;
 }
@@ -463,14 +442,10 @@ void stmmac_pcs_clean(struct net_device *ndev)
 {
 	struct stmmac_priv *priv = netdev_priv(ndev);
 
-	if (priv->plat->pcs_exit)
-		priv->plat->pcs_exit(priv);
-
-	if (!priv->hw->xpcs)
+	if (!priv->plat->pcs_exit)
 		return;
 
-	xpcs_destroy(priv->hw->xpcs);
-	priv->hw->xpcs = NULL;
+	priv->plat->pcs_exit(priv);
 }
 
 struct stmmac_clk_rate {
-- 
2.47.3

[PATCH net-next v8 02/11] dt-bindings: phy: rockchip: naneng-combphy: add rockchip,sgmii-mac-sel property

[Coia Prant]

On RK3568, the SGMII interface can be routed to either GMAC0 or
GMAC1 via the pipe_sgmii_mac_sel bit in the pipe GRF registers.

Add the optional "rockchip,sgmii-mac-sel" property to allow the
device tree to select which GMAC controller is used for SGMII.

The property takes a value of 0 (GMAC0) or 1 (GMAC1). The hardware
reset value is 1 (GMAC1), but this can be overridden by setting the
property to 0 for boards where SGMII is connected to GMAC0.

This is necessary for boards such as the Ariaboard Photonicat, where
the SGMII interface is connected to GMAC0 and needs to be explicitly
configured.

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 .../bindings/phy/phy-rockchip-naneng-combphy.yaml   | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
index 379b08bd9e97a..8e898bce9af73 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml
@@ -80,6 +80,15 @@ properties:
     description:
       Some additional pipe settings are accessed through GRF regs.
 
+  rockchip,sgmii-mac-sel:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+    default: 1
+    description:
+      Select gmac0 or gmac1 to be used as SGMII controller.
+      The hardware reset value is GMAC1 (1). Set this to 0 to route
+      SGMII to GMAC0.
+
   "#phy-cells":
     const: 1
 
@@ -105,6 +114,10 @@ allOf:
           maxItems: 1
         reset-names:
           maxItems: 1
+        rockchip,sgmii-mac-sel: true
+    else:
+      properties:
+        rockchip,sgmii-mac-sel: false
   - if:
       properties:
         compatible:
-- 
2.47.3

[PATCH net-next v8 03/11] phy: rockchip: naneng-combphy: add SGMII MAC selection for RK3568

[Coia Prant]

On RK3568, the SGMII interface can be routed to either GMAC0 or
GMAC1 via the GRF register pipe_sgmii_mac_sel.

Add support for this selection by introducing
the "rockchip,sgmii-mac-sel" DT property.

From the RK3568 TRM (Part1, Page 229), the PIPE_GRF_XPCS_CON0
bit 1 (pipe_sgmii_mac_sel) is defined as:

    0: SGMII routed to GMAC0
    1: SGMII routed to GMAC1

The hardware reset value is 1 (GMAC1). If the property is set to 0,
the driver routes SGMII to GMAC0; if set to 1 (or omitted), it
remains at GMAC1.

This is necessary for boards such as the Ariaboard Photonicat, which
uses the SGMII interface connected to GMAC0.

Out-of-range values are rejected by dtschema, so the driver does not
duplicate the range check.

Link: https://dl.radxa.com/rock3/docs/hw/datasheet/Rockchip%20RK3568%20TRM%20Part1%20V1.1-20210301.pdf (Page 229)
Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 drivers/phy/rockchip/phy-rockchip-naneng-combphy.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
index 7843356a4dd47..7b867e7520064 100644
--- a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
+++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
@@ -186,6 +186,7 @@ struct rockchip_combphy_grfcfg {
 	struct combphy_reg pipe_xpcs_phy_ready;
 	struct combphy_reg pipe_pcie1l0_sel;
 	struct combphy_reg pipe_pcie1l1_sel;
+	struct combphy_reg pipe_sgmii_mac_sel;
 	struct combphy_reg u3otg0_port_en;
 	struct combphy_reg u3otg1_port_en;
 };
@@ -212,6 +213,7 @@ struct rockchip_combphy_priv {
 	bool enable_ssc;
 	bool ext_refclk;
 	struct clk *refclk;
+	u32 sgmii_mac_sel;
 };
 
 static void rockchip_combphy_updatel(struct rockchip_combphy_priv *priv,
@@ -375,6 +377,9 @@ static int rockchip_combphy_parse_dt(struct device *dev, struct rockchip_combphy
 
 	priv->ext_refclk = device_property_present(dev, "rockchip,ext-refclk");
 
+	priv->sgmii_mac_sel = 1;
+	device_property_read_u32(dev, "rockchip,sgmii-mac-sel", &priv->sgmii_mac_sel);
+
 	priv->phy_rst = devm_reset_control_get_exclusive(dev, "phy");
 	/* fallback to old behaviour */
 	if (PTR_ERR(priv->phy_rst) == -ENOENT)
@@ -873,6 +878,8 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 		break;
 
 	case PHY_TYPE_SGMII:
+		rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_sgmii_mac_sel,
+					     priv->sgmii_mac_sel > 0);
 		rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_xpcs_phy_ready, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_phymode_sel, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_qsgmii, true);
@@ -984,6 +991,7 @@ static const struct rockchip_combphy_grfcfg rk3568_combphy_grfcfgs = {
 	.con3_for_sata		= { 0x000c, 15, 0, 0x00, 0x4407 },
 	/* pipe-grf */
 	.pipe_con0_for_sata	= { 0x0000, 15, 0, 0x00, 0x2220 },
+	.pipe_sgmii_mac_sel	= { 0x0040, 1, 1, 0x00, 0x01 },
 	.pipe_xpcs_phy_ready	= { 0x0040, 2, 2, 0x00, 0x01 },
 	.u3otg0_port_en		= { 0x0104, 15, 0, 0x0181, 0x1100 },
 	.u3otg1_port_en		= { 0x0144, 15, 0, 0x0181, 0x1100 },
-- 
2.47.3

[PATCH net-next v8 04/11] dt-bindings: net: pcs: add rockchip,rk3568-xpcs support

[Coia Prant]

Add device tree binding documentation for the Synopsys DesignWare
XPCS integrated on the Rockchip RK3568 SoC.

The XPCS is accessed over the APB3 bus and internally connected to
a Naneng Combo SerDes PHY.  It supports 1000BASE-X, SGMII, and
QSGMII modes, with four MII ports.

The four MII ports are described as ethernet-pcs-mii@N child nodes,
consumed by the Rockchip XPCS glue driver later in this series.

phys and phy-names are required because dtbs_check only validates
required properties for enabled nodes. The SerDes link is a board-level
design choice (combphy1 on some boards, combphy2 on others), so these
properties must be provided by the board device tree, not the SoC dtsi.

The CRU reset lines (SRST_XPCS*) are intentionally not described: no
in-tree user requests them, and bring-up relies on the PD_PIPE power
domain, the SerDes PHY and the in-IP soft reset. They can be added
later as optional without breaking ABI.

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 .../net/pcs/rockchip,rk3568-xpcs.yaml         | 110 ++++++++++++++++++
 1 file changed, 110 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/pcs/rockchip,rk3568-xpcs.yaml

diff --git a/Documentation/devicetree/bindings/net/pcs/rockchip,rk3568-xpcs.yaml b/Documentation/devicetree/bindings/net/pcs/rockchip,rk3568-xpcs.yaml
new file mode 100644
index 0000000000000..703fcff0e3f70
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/pcs/rockchip,rk3568-xpcs.yaml
@@ -0,0 +1,110 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/pcs/rockchip,rk3568-xpcs.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip RK3568 Synopsys DesignWare Ethernet PCS
+
+maintainers:
+  - Coia Prant <coiaprant@gmail.com>
+
+description: |
+  Rockchip RK3568 SoC integrates a Synopsys DesignWare Ethernet Physical
+  Coding Sublayer (XPCS).
+  The PCS provides an interface between the Media Access Control (MAC)
+  and the Physical Medium Attachment (PMA) sublayer through a Media
+  Independent Interface (GMII).
+
+  The XPCS is accessed over the APB3 bus and internally connected to a
+  Naneng Combo SerDes PHY.
+  It supports 1000BASE-X, SGMII and QSGMII modes.
+
+  The block contains four MII ports that can be individually enabled and
+  routed to one of the Ethernet GMAC controllers via the pcs-handle
+  property in the MAC device tree node.
+
+properties:
+  compatible:
+    const: rockchip,rk3568-xpcs
+
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  clocks:
+    items:
+      - description: APB3 bus interface clock (clk_csr_i), required for register access
+      - description: EEE clock (clk_eee_i), required for Energy Efficient Ethernet operation
+
+  clock-names:
+    items:
+      - const: csr
+      - const: eee
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    const: serdes
+
+  power-domains:
+    maxItems: 1
+
+patternProperties:
+  "^ethernet-pcs-mii@[0-3]$":
+    type: object
+    description:
+      One of the four MII ports of the XPCS. The port is linked to an
+      Ethernet MAC controller via the pcs-handle property in the MAC's
+      device tree node.
+
+    properties:
+      reg:
+        description: MII port number.
+        enum: [0, 1, 2, 3]
+
+    required:
+      - reg
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+  - clocks
+  - clock-names
+  - phys
+  - phy-names
+  - power-domains
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/rk3568-cru.h>
+    #include <dt-bindings/power/rk3568-power.h>
+    #include <dt-bindings/phy/phy.h>
+
+    ethernet-pcs@fda00000 {
+      compatible = "rockchip,rk3568-xpcs";
+      reg = <0xfda00000 0x200000>;
+      #address-cells = <1>;
+      #size-cells = <0>;
+      clocks = <&cru PCLK_XPCS>, <&cru CLK_XPCS_EEE>;
+      clock-names = "csr", "eee";
+      phys = <&combphy2 PHY_TYPE_SGMII>;
+      phy-names = "serdes";
+      power-domains = <&power RK3568_PD_PIPE>;
+
+      ethernet-pcs-mii@0 {
+        reg = <0>;
+      };
+    };
-- 
2.47.3

[PATCH net-next v8 05/11] arm64: dts: rockchip: rk3568: add XPCS and fixed-clock nodes

[Coia Prant]

The RK3568 SoC integrates a Synopsys DesignWare XPCS that provides
the Physical Coding Sublayer for 1000BASE-X, SGMII, and QSGMII
interfaces via its four MII ports.  Add the XPCS device node and
its pcs-mii sub-nodes to the SoC device tree.

The XPCS device is accessed via the APB3 bus at 0xfda00000 and
requires the CSR clock (PCLK_XPCS) for register access and the EEE
clock (CLK_XPCS_EEE) for Energy Efficient Ethernet operation.  The
PD_PIPE power domain must be enabled before any register access.

Also add two fixed-clock nodes (clock-xpcs-gmac0 and clock-xpcs-gmac1,
labelled clk_gmac0_xpcs_mii and clk_gmac1_xpcs_mii) providing the
125 MHz reference clock for the GMACs when operating with XPCS.  Their
clock-output-names match the CRU mux parent names in clk-rk3568.c, so
boards can reparent SCLK_GMAC0_RX_TX / SCLK_GMAC1_RX_TX through
assigned-clock-parents.

The XPCS node and its mii sub-nodes are disabled by default and
must be enabled at the board level when 1000BASE-X/SGMII/QSGMII is
in use.  The fixed-clock nodes are always present and do not have a
status property, as they are static clock sources.

The XPCS node requires a reference to the appropriate Naneng Combo PHY
via the phys property.  dtbs_check only validates required properties
for enabled nodes, so the SoC dtsi does not provide phys/phy-names:
boards that enable the XPCS must supply them, since the SerDes link is
a board-level design choice (combphy1 on some boards, combphy2 on
others).

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3568.dtsi | 45 ++++++++++++++++++++++++
 1 file changed, 45 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568.dtsi b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
index 3bc653f027f1f..227d03e336043 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
@@ -110,6 +110,51 @@ sata0: sata@fc000000 {
 		status = "disabled";
 	};
 
+	xpcs: ethernet-pcs@fda00000 {
+		compatible = "rockchip,rk3568-xpcs";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x0 0xfda00000 0x0 0x200000>;
+		clocks = <&cru PCLK_XPCS>, <&cru CLK_XPCS_EEE>;
+		clock-names = "csr", "eee";
+		power-domains = <&power RK3568_PD_PIPE>;
+		status = "disabled";
+
+		xpcs_mii0: ethernet-pcs-mii@0 {
+			reg = <0>;
+			status = "disabled";
+		};
+
+		xpcs_mii1: ethernet-pcs-mii@1 {
+			reg = <1>;
+			status = "disabled";
+		};
+
+		xpcs_mii2: ethernet-pcs-mii@2 {
+			reg = <2>;
+			status = "disabled";
+		};
+
+		xpcs_mii3: ethernet-pcs-mii@3 {
+			reg = <3>;
+			status = "disabled";
+		};
+	};
+
+	clk_gmac0_xpcs_mii: clock-xpcs-gmac0 {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clk_gmac0_xpcs_mii";
+		#clock-cells = <0>;
+	};
+
+	clk_gmac1_xpcs_mii: clock-xpcs-gmac1 {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clk_gmac1_xpcs_mii";
+		#clock-cells = <0>;
+	};
+
 	pipe_phy_grf0: syscon@fdc70000 {
 		compatible = "rockchip,rk3568-pipe-phy-grf", "syscon";
 		reg = <0x0 0xfdc70000 0x0 0x1000>;
-- 
2.47.3

[PATCH net-next v8 06/11] net: pcs: xpcs: add ANRESTART support for SGMII link recovery

[Coia Prant]

On some hardware using the DesignWare XPCS IP (e.g., RK3568 MAC side
SGMII), the PCS does not automatically restart auto-negotiation when the
link goes down and comes back up. Without an explicit ANRESTART, the link
stays down forever.

Add BMCR_ANRESTART in two places:
1. In xpcs_config_aneg_c37_sgmii(), when starting AN, set ANRESTART
   alongside ANENABLE to initiate a fresh negotiation.
2. In xpcs_get_state_c37_sgmii(), when link is down and AN completion is
   detected, clear the interrupt and trigger ANRESTART to restart the
   negotiation process. Propagate the return value of the restart so
   errors are not silently ignored.

The restart cannot go through the .pcs_an_restart op: phylink only
calls it for 802.3z interfaces, and SGMII is not one. Changing hardware
state from pcs_get_state() is already done elsewhere in this driver
(xpcs_get_state_c73() calls xpcs_soft_reset() and xpcs_do_config()),
so the same pattern is used here.

The latch is cleared before issuing the restart, not after: clearing it
afterwards would discard a freshly latched ANCMPLT from the new
negotiation. If an MDIO access fails at this point, it indicates an
unrecoverable hardware condition until reset.

Also clear DW_VR_MII_AN_INTR_STS in xpcs_config_aneg_c37_sgmii() before
starting AN, matching what xpcs_config_aneg_c37_1000basex() already does.
On the non-inband path the function now returns the result of that write
instead of the DIG_CTRL1 modify.

Update the comment in xpcs_config_aneg_c37_sgmii() to note that although
the DesignWare databook says AN restart is not needed for MAC side SGMII,
some implementations (e.g. Rockchip RK3568) require it to recover the
link after a disconnect.

This is not a fix for an existing mainline platform: the affected
platform (RK3568 XPCS) is introduced later in the same series.

Tested-by: Jiawen Wu <jiawenwu@trustnetic.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 drivers/net/pcs/pcs-xpcs.c | 35 +++++++++++++++++++++++++++++------
 1 file changed, 29 insertions(+), 6 deletions(-)

diff --git a/drivers/net/pcs/pcs-xpcs.c b/drivers/net/pcs/pcs-xpcs.c
index 0337e2bcc0125..8c3875b6985b9 100644
--- a/drivers/net/pcs/pcs-xpcs.c
+++ b/drivers/net/pcs/pcs-xpcs.c
@@ -761,7 +761,9 @@ static int xpcs_config_aneg_c37_sgmii(struct dw_xpcs *xpcs,
 	 *    DW xPCS used with DW EQoS MAC is always MAC side SGMII.
 	 * 4) VR_MII_DIG_CTRL1 Bit(9) [MAC_AUTO_SW] = 1b (Automatic
 	 *    speed/duplex mode change by HW after SGMII AN complete)
-	 * 5) VR_MII_MMD_CTRL Bit(12) [AN_ENABLE] = 1b (Enable SGMII AN)
+	 * 5) VR_MII_AN_INTR_STS = 0x0 (Clear CL37 AN complete status)
+	 * 6) VR_MII_MMD_CTRL Bit(12) [AN_ENABLE] = 1b (Enable SGMII AN)
+	 *    VR_MII_MMD_CTRL Bit(9) [AN_RESTART] = 1b (Restart SGMII AN)
 	 *
 	 * Note that VR_MII_MMD_CTRL is MII_BMCR.
 	 *
@@ -769,7 +771,14 @@ static int xpcs_config_aneg_c37_sgmii(struct dw_xpcs *xpcs,
 	 *	 SR_MII_AN_ADV. MAC side SGMII receives AN Tx Config from
 	 *	 PHY about the link state change after C28 AN is completed
 	 *	 between PHY and Link Partner. There is also no need to
-	 *	 trigger AN restart for MAC-side SGMII.
+	 *	 trigger AN restart for MAC-side SGMII on most devices.
+	 *
+	 * Note: While the DesignWare databook states that AN restart is
+	 *	 not needed for MAC side SGMII, some implementations (e.g.
+	 *	 Rockchip RK3568) exhibit a timing quirk when integrated with
+	 *	 phylink and do not restart AN automatically when the link
+	 *	 comes back up. An explicit AN restart is required on those
+	 *	 parts to recover the link after a disconnect.
 	 */
 	mdio_ctrl = xpcs_read(xpcs, MDIO_MMD_VEND2, MII_BMCR);
 	if (mdio_ctrl < 0)
@@ -816,9 +825,14 @@ static int xpcs_config_aneg_c37_sgmii(struct dw_xpcs *xpcs,
 	if (ret < 0)
 		return ret;
 
+	/* Clear CL37 AN complete status */
+	ret = xpcs_write(xpcs, MDIO_MMD_VEND2, DW_VR_MII_AN_INTR_STS, 0);
+	if (ret < 0)
+		return ret;
+
 	if (neg_mode == PHYLINK_PCS_NEG_INBAND_ENABLED)
 		ret = xpcs_write(xpcs, MDIO_MMD_VEND2, MII_BMCR,
-				 mdio_ctrl | BMCR_ANENABLE);
+				 mdio_ctrl | BMCR_ANENABLE | BMCR_ANRESTART);
 
 	return ret;
 }
@@ -1093,9 +1107,18 @@ static int xpcs_get_state_c37_sgmii(struct dw_xpcs *xpcs,
 		return 0;
 	}
 
-	/* Clear AN complete status or interrupt */
-	if (state->an_complete)
-		xpcs_write(xpcs, MDIO_MMD_VEND2, DW_VR_MII_AN_INTR_STS, 0);
+	if (state->an_complete) {
+		/* Clear AN complete status or interrupt */
+		ret = xpcs_write(xpcs, MDIO_MMD_VEND2, DW_VR_MII_AN_INTR_STS, 0);
+		if (ret < 0)
+			return ret;
+
+		/* Initiate the next round of AN */
+		ret = xpcs_modify(xpcs, MDIO_MMD_VEND2, MII_BMCR, BMCR_ANRESTART,
+				  BMCR_ANRESTART);
+		if (ret < 0)
+			return ret;
+	}
 
 	return 0;
 }
-- 
2.47.3

[PATCH net-next v8 07/11] net: pcs: xpcs: add Rockchip RK3568 platform glue driver

[Coia Prant]

The RK3568 SoC integrates a Synopsys DesignWare XPCS that is accessed
via APB3 memory-mapped registers.
This driver provides the glue logic to make the XPCS accessible to
the generic pcs-xpcs core.

The XPCS block contains four MII ports (0..3), each of which can be
routed to GMAC0 or GMAC1 via the pcs-handle property in the MAC node.
The hardware maps these ports to different MMDs:
  - port 0: MMD 7 (ROCKCHIP_MMD_MII)
  - port 1: MMD 2 (ROCKCHIP_MMD_MII1)
  - port 2: MMD 3 (ROCKCHIP_MMD_MII2)
  - port 3: MMD 4 (ROCKCHIP_MMD_MII3)

This driver creates a virtual MDIO bus that translates MDIO operations
to APB3 register accesses, with proper address remapping for each port.
The generic xpcs driver then creates a phylink_pcs instance on top of
this bus, allowing the MAC to use the PCS via the standard phylink API.

The generic XPCS platform glue (pcs-xpcs-plat.o) is split out of the
pcs_xpcs composite object into its own module, gated behind the new
PCS_XPCS_PLATFORM symbol. The symbol defaults to PCS_XPCS, so existing
configurations keep the snps,dw-xpcs platform glue enabled without any
change.

PCS_XPCS_ROCKCHIP selects GENERIC_PHY and PM_GENERIC_DOMAINS.
ARCH_ROCKCHIP already selects PM, so the dependency of PM_GENERIC_DOMAINS
on PM is satisfied on the target platform.

The EEE multiplier is derived at runtime from the EEE clock rate
instead of being hardcoded, because the clock is muxed between
gpll200 (200 MHz) and cpll125 (125 MHz) and can be changed by the
board or firmware. A 64-bit intermediate avoids overflow on 32-bit
builds, and the result is clamped to the 4-bit
DW_VR_MII_EEE_MULT_FACT_100NS field.

Link: https://dl.radxa.com/rock3/docs/hw/datasheet/Rockchip%20RK3568%20TRM%20Part1%20V1.1-20210301.pdf (Page 59, CRU_CLKSEL_CON29)
Link: https://dl.radxa.com/rock3/docs/hw/datasheet/Rockchip%20RK3568%20TRM%20Part2%20V1.1-20210301.pdf (Page 2078)
Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 drivers/net/pcs/Kconfig         |  25 ++
 drivers/net/pcs/Makefile        |   5 +-
 drivers/net/pcs/pcs-xpcs-rk.c   | 599 ++++++++++++++++++++++++++++++++
 include/linux/pcs/pcs-xpcs-rk.h |  11 +
 4 files changed, 638 insertions(+), 2 deletions(-)
 create mode 100644 drivers/net/pcs/pcs-xpcs-rk.c
 create mode 100644 include/linux/pcs/pcs-xpcs-rk.h

diff --git a/drivers/net/pcs/Kconfig b/drivers/net/pcs/Kconfig
index e417fd66f660a..5382afcf95748 100644
--- a/drivers/net/pcs/Kconfig
+++ b/drivers/net/pcs/Kconfig
@@ -12,6 +12,31 @@ config PCS_XPCS
 	  This module provides a driver and helper functions for Synopsys
 	  DesignWare XPCS controllers.
 
+if PCS_XPCS
+
+config PCS_XPCS_PLATFORM
+	tristate "Generic XPCS controller support"
+	default PCS_XPCS
+	help
+	  Generic DWXPCS driver for platforms that don't require any
+	  platform specific code to function or is using platform
+	  data for setup.
+
+	  If you have a controller with this interface, say Y or M here.
+
+config PCS_XPCS_ROCKCHIP
+	tristate "Rockchip XPCS controller support"
+	default ARCH_ROCKCHIP
+	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
+	select GENERIC_PHY
+	select PM_GENERIC_DOMAINS if PM
+	help
+	  Support for XPCS controller on Rockchip RK356x SoC.
+
+	  If you have a Rockchip SoC with this interface, say Y or M here.
+
+endif # PCS_XPCS
+
 config PCS_LYNX
 	tristate
 	help
diff --git a/drivers/net/pcs/Makefile b/drivers/net/pcs/Makefile
index 4f7920618b900..f9f6cf2578d72 100644
--- a/drivers/net/pcs/Makefile
+++ b/drivers/net/pcs/Makefile
@@ -1,10 +1,11 @@
 # SPDX-License-Identifier: GPL-2.0
 # Makefile for Linux PCS drivers
 
-pcs_xpcs-$(CONFIG_PCS_XPCS)	:= pcs-xpcs.o pcs-xpcs-plat.o \
-				   pcs-xpcs-nxp.o pcs-xpcs-wx.o
+pcs_xpcs-$(CONFIG_PCS_XPCS)	:= pcs-xpcs.o pcs-xpcs-nxp.o pcs-xpcs-wx.o
 
 obj-$(CONFIG_PCS_XPCS)		+= pcs_xpcs.o
+obj-$(CONFIG_PCS_XPCS_PLATFORM) += pcs-xpcs-plat.o
+obj-$(CONFIG_PCS_XPCS_ROCKCHIP) += pcs-xpcs-rk.o
 obj-$(CONFIG_PCS_LYNX)		+= pcs-lynx.o
 obj-$(CONFIG_PCS_MTK_LYNXI)	+= pcs-mtk-lynxi.o
 obj-$(CONFIG_PCS_RZN1_MIIC)	+= pcs-rzn1-miic.o
diff --git a/drivers/net/pcs/pcs-xpcs-rk.c b/drivers/net/pcs/pcs-xpcs-rk.c
new file mode 100644
index 0000000000000..84f8ea7fa57e8
--- /dev/null
+++ b/drivers/net/pcs/pcs-xpcs-rk.c
@@ -0,0 +1,599 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Rockchip XPCS platform device driver
+ *
+ * Based on the Synopsys DesignWare XPCS platform driver.
+ * Copyright (C) 2024 Serge Semin
+ *
+ * Adapted for Rockchip SoCs, with reference to the Rockchip OEM driver.
+ * Copyright (C) 2026 Coia Prant
+ */
+
+#include <linux/atomic.h>
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/math.h>
+#include <linux/mdio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pcs/pcs-xpcs-rk.h>
+#include <linux/phy.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
+#include <linux/property.h>
+#include <linux/sizes.h>
+#include <linux/time.h>
+
+#include "pcs-xpcs.h"
+
+struct dw_xpcs_rk {
+	struct platform_device *pdev;
+	struct mii_bus *bus;
+	void __iomem *reg_base;
+	struct phy *serdes_phy;
+	struct clk *csr_clk;
+	struct clk *eee_clk;
+	u8 eee_mult_fact;
+};
+
+static ptrdiff_t xpcs_rk_addr_format(int dev, int reg)
+{
+	return FIELD_PREP(0x70000, dev) | FIELD_PREP(0xffff, reg);
+}
+
+static int xpcs_rk_read_reg(struct dw_xpcs_rk *pxpcs, int dev, int reg)
+{
+	ptrdiff_t csr;
+	int ret;
+
+	csr = xpcs_rk_addr_format(dev, reg);
+
+	ret = pm_runtime_resume_and_get(&pxpcs->pdev->dev);
+	if (ret)
+		return ret;
+
+	ret = readl(pxpcs->reg_base + (csr << 2)) & 0xffff;
+
+	pm_runtime_put(&pxpcs->pdev->dev);
+	return ret;
+}
+
+static int xpcs_rk_write_reg(struct dw_xpcs_rk *pxpcs, int dev, int reg, u16 val)
+{
+	ptrdiff_t csr;
+	int ret;
+
+	csr = xpcs_rk_addr_format(dev, reg);
+
+	ret = pm_runtime_resume_and_get(&pxpcs->pdev->dev);
+	if (ret)
+		return ret;
+
+	writel(val, pxpcs->reg_base + (csr << 2));
+
+	pm_runtime_put(&pxpcs->pdev->dev);
+	return 0;
+}
+
+#define ROCKCHIP_MMD_MII1	2
+#define ROCKCHIP_MMD_MII2	3
+#define ROCKCHIP_MMD_MII3	4
+#define ROCKCHIP_MMD_PMAPMD	6
+#define ROCKCHIP_MMD_MII	7
+
+static bool xpcs_rk_mdio_addr_validate(int addr)
+{
+	return !(addr < 0 || addr > 3);
+}
+
+static int xpcs_rk_mdio_read_remapping(int addr, int dev, int reg)
+{
+	switch (dev) {
+	case MDIO_MMD_PMAPMD:
+		return ROCKCHIP_MMD_PMAPMD;
+	case MDIO_MMD_VEND2:
+		break;
+	default:
+		return -ENXIO;
+	}
+
+	/*
+	 * Reads are redirected by hardware to the port's read-only mirror;
+	 * only writes have to be targeted at MII (see the write path).
+	 */
+	switch (addr) {
+	case 0:
+		return ROCKCHIP_MMD_MII;
+	case 1:
+		return ROCKCHIP_MMD_MII1;
+	case 2:
+		return ROCKCHIP_MMD_MII2;
+	case 3:
+		return ROCKCHIP_MMD_MII3;
+	default:
+		return -ENODEV;
+	}
+}
+
+static int xpcs_rk_mdio_write_remapping(int addr, int dev, int reg)
+{
+	switch (dev) {
+	case MDIO_MMD_PMAPMD:
+		return ROCKCHIP_MMD_PMAPMD;
+	case MDIO_MMD_VEND2:
+		break;
+	default:
+		return -ENXIO;
+	}
+
+	/*
+	 * These registers physically live only in MII (the management port).
+	 * Ports 1-3 expose read-only mirrors of these bits, so writes must
+	 * always target MII; the read path remaps per address and the
+	 * hardware redirects to the port's mirror.
+	 */
+	switch (reg) {
+	case DW_VR_MII_AN_CTRL:
+	case DW_VR_MII_AN_INTR_STS:
+	case DW_VR_MII_EEE_MCTRL0:
+	case DW_VR_MII_EEE_MCTRL1:
+	case DW_VR_MII_DIG_CTRL2:
+		return ROCKCHIP_MMD_MII;
+	default:
+		break;
+	}
+
+	switch (addr) {
+	case 0:
+		return ROCKCHIP_MMD_MII;
+	case 1:
+		return ROCKCHIP_MMD_MII1;
+	case 2:
+		return ROCKCHIP_MMD_MII2;
+	case 3:
+		return ROCKCHIP_MMD_MII3;
+	default:
+		return -ENODEV;
+	}
+}
+
+static int xpcs_rk_read_c22(struct mii_bus *bus, int addr, int reg)
+{
+	struct dw_xpcs_rk *pxpcs = bus->priv;
+	int dev;
+
+	if (!xpcs_rk_mdio_addr_validate(addr))
+		return -ENODEV;
+
+	dev = xpcs_rk_mdio_read_remapping(addr, MDIO_MMD_VEND2, reg);
+	if (dev < 0)
+		return 0xffff;
+
+	return xpcs_rk_read_reg(pxpcs, dev, reg);
+}
+
+static int xpcs_rk_write_c22(struct mii_bus *bus, int addr, int reg, u16 val)
+{
+	struct dw_xpcs_rk *pxpcs = bus->priv;
+	int dev;
+
+	if (!xpcs_rk_mdio_addr_validate(addr))
+		return -ENODEV;
+
+	dev = xpcs_rk_mdio_write_remapping(addr, MDIO_MMD_VEND2, reg);
+	if (dev < 0)
+		return 0;
+
+	return xpcs_rk_write_reg(pxpcs, dev, reg, val);
+}
+
+static int xpcs_rk_read_c45(struct mii_bus *bus, int addr, int dev, int reg)
+{
+	struct dw_xpcs_rk *pxpcs = bus->priv;
+
+	if (!xpcs_rk_mdio_addr_validate(addr))
+		return -ENODEV;
+
+	dev = xpcs_rk_mdio_read_remapping(addr, dev, reg);
+	if (dev < 0)
+		return 0xffff;
+
+	return xpcs_rk_read_reg(pxpcs, dev, reg);
+}
+
+static int xpcs_rk_write_c45(struct mii_bus *bus, int addr, int dev, int reg, u16 val)
+{
+	struct dw_xpcs_rk *pxpcs = bus->priv;
+
+	if (!xpcs_rk_mdio_addr_validate(addr))
+		return -ENODEV;
+
+	dev = xpcs_rk_mdio_write_remapping(addr, dev, reg);
+	if (dev < 0)
+		return 0;
+
+	return xpcs_rk_write_reg(pxpcs, dev, reg, val);
+}
+
+static struct dw_xpcs_rk *xpcs_rk_create_data(struct platform_device *pdev)
+{
+	struct dw_xpcs_rk *pxpcs;
+
+	pxpcs = devm_kzalloc(&pdev->dev, sizeof(*pxpcs), GFP_KERNEL);
+	if (!pxpcs)
+		return ERR_PTR(-ENOMEM);
+
+	pxpcs->pdev = pdev;
+
+	dev_set_drvdata(&pdev->dev, pxpcs);
+
+	return pxpcs;
+}
+
+static int xpcs_rk_serdes_phy_init(struct dw_xpcs_rk *pxpcs)
+{
+	struct device *dev = &pxpcs->pdev->dev;
+
+	pxpcs->serdes_phy = devm_phy_get(dev, "serdes");
+	if (IS_ERR(pxpcs->serdes_phy))
+		return dev_err_probe(dev, PTR_ERR(pxpcs->serdes_phy),
+					"Failed to get SerDes PHY\n");
+
+	return 0;
+}
+
+static void xpcs_rk_serdes_phy_poweroff(void *data)
+{
+	struct dw_xpcs_rk *pxpcs = data;
+	struct device *dev = &pxpcs->pdev->dev;
+
+	phy_power_off(pxpcs->serdes_phy);
+	phy_exit(pxpcs->serdes_phy);
+
+	dev_pm_genpd_rpm_always_on(dev, false);
+}
+
+static int xpcs_rk_serdes_phy_poweron(struct dw_xpcs_rk *pxpcs)
+{
+	struct device *dev = &pxpcs->pdev->dev;
+	int ret;
+
+	/*
+	 * The power domain is required and must be enabled, which allows us to
+	 * dynamically turn the CSR clock on/off using PM while keeping the PCS
+	 * powered on.
+	 */
+	ret = dev_pm_genpd_rpm_always_on(dev, true);
+	if (ret) {
+		dev_err(dev, "Failed to power on power-domains\n");
+		return ret;
+	}
+
+	ret = phy_init(pxpcs->serdes_phy);
+	if (ret) {
+		dev_err(dev, "Failed to init SerDes PHY\n");
+		goto pm_domain;
+	}
+
+	ret = phy_power_on(pxpcs->serdes_phy);
+	if (ret) {
+		dev_err(dev, "Failed to power on SerDes PHY\n");
+		goto serdes_phy;
+	}
+
+	ret = devm_add_action_or_reset(dev, xpcs_rk_serdes_phy_poweroff, pxpcs);
+	if (ret) {
+		dev_err(dev, "Failed to register devm for SerDes PHY: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+
+serdes_phy:
+	phy_exit(pxpcs->serdes_phy);
+pm_domain:
+	dev_pm_genpd_rpm_always_on(dev, false);
+	return ret;
+}
+
+static int xpcs_rk_init_res(struct dw_xpcs_rk *pxpcs)
+{
+	struct platform_device *pdev = pxpcs->pdev;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "No reg-space found\n");
+		return -EINVAL;
+	}
+
+	if (resource_size(res) < SZ_2M) {
+		dev_err(dev, "Invalid reg-space size\n");
+		return -EINVAL;
+	}
+
+	pxpcs->reg_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(pxpcs->reg_base)) {
+		dev_err(dev, "Failed to map reg-space\n");
+		return PTR_ERR(pxpcs->reg_base);
+	}
+
+	return 0;
+}
+
+static void xpcs_rk_exit_clk(void *data)
+{
+	struct dw_xpcs_rk *pxpcs = data;
+	struct device *dev = &pxpcs->pdev->dev;
+
+	pm_runtime_force_suspend(dev);
+	clk_disable_unprepare(pxpcs->eee_clk);
+}
+
+static int xpcs_rk_init_clk(struct dw_xpcs_rk *pxpcs)
+{
+	struct device *dev = &pxpcs->pdev->dev;
+	unsigned long rate;
+	u64 mult;
+	int ret;
+
+	pxpcs->csr_clk = devm_clk_get(dev, "csr");
+	if (IS_ERR(pxpcs->csr_clk))
+		return dev_err_probe(dev, PTR_ERR(pxpcs->csr_clk),
+					 "Failed to get CSR clock\n");
+
+	pxpcs->eee_clk = devm_clk_get(dev, "eee");
+	if (IS_ERR(pxpcs->eee_clk))
+		return dev_err_probe(dev, PTR_ERR(pxpcs->eee_clk),
+					 "Failed to get EEE clock\n");
+
+	ret = clk_prepare_enable(pxpcs->eee_clk);
+	if (ret) {
+		dev_err(dev, "Failed to enable EEE clock\n");
+		return ret;
+	}
+
+	pm_runtime_set_suspended(dev);
+	pm_runtime_enable(dev);
+
+	ret = devm_add_action_or_reset(dev, xpcs_rk_exit_clk, pxpcs);
+	if (ret) {
+		dev_err(dev, "Failed to register devm for EEE clock: %d\n", ret);
+		return ret;
+	}
+
+	/*
+	 * Compute the multiplier for the EEE clock so that
+	 * clk_eee_period * (mult_fact + 1) falls within 80..120 ns.
+	 *
+	 * On RK3568, clk_xpcs_eee is muxed between gpll200 (200 MHz, 5 ns)
+	 * and cpll125 (125 MHz, 8 ns), selected by CRU_CLKSEL_CON29 bit 13.
+	 * The reset value is 0 (200 MHz), but derive the value at runtime to
+	 * stay correct if the mux is changed by a board.
+	 *
+	 * Use a 64-bit intermediate: on 32-bit builds, 100 * 200000000
+	 * does not fit in unsigned long. Clamp to the 4-bit
+	 * DW_VR_MII_EEE_MULT_FACT_100NS field. The mux only provides
+	 * 125 MHz or 200 MHz, so the rate cannot drop below the 5 MHz
+	 * threshold where DIV_ROUND_CLOSEST_ULL() would return 0 and the
+	 * subtraction below would underflow.
+	 */
+	rate = clk_get_rate(pxpcs->eee_clk);
+	if (!rate)
+		return dev_err_probe(dev, -EINVAL, "Invalid EEE clock rate\n");
+
+	mult = DIV_ROUND_CLOSEST_ULL(100ULL * rate, NSEC_PER_SEC) - 1;
+	pxpcs->eee_mult_fact = min_t(u64, mult, 15);
+	return 0;
+}
+
+static int xpcs_rk_init_bus(struct dw_xpcs_rk *pxpcs)
+{
+	struct device *dev = &pxpcs->pdev->dev;
+	static atomic_t id = ATOMIC_INIT(-1);
+	struct mii_bus *bus;
+	int ret;
+
+	bus = devm_mdiobus_alloc_size(dev, 0);
+	if (!bus)
+		return -ENOMEM;
+
+	bus->name = "Rockchip DW XPCS MCI/APB3";
+	bus->read = xpcs_rk_read_c22;
+	bus->write = xpcs_rk_write_c22;
+	bus->read_c45 = xpcs_rk_read_c45;
+	bus->write_c45 = xpcs_rk_write_c45;
+	bus->phy_mask = ~0;
+	bus->parent = dev;
+	bus->priv = pxpcs;
+
+	snprintf(bus->id, MII_BUS_ID_SIZE,
+		 "rockchip_dwxpcs-%x", atomic_inc_return(&id));
+
+	/*
+	 * MDIO-bus here serves as just a back-end engine abstracting out
+	 * the MDIO and MCI/APB3 IO interfaces utilized for the Rockchip DWXPCS CSRs
+	 * access.
+	 */
+	ret = devm_mdiobus_register(dev, bus);
+	if (ret) {
+		dev_err(dev, "Failed to create MDIO bus\n");
+		return ret;
+	}
+
+	pxpcs->bus = bus;
+	return 0;
+}
+
+static int xpcs_rk_probe(struct platform_device *pdev)
+{
+	struct dw_xpcs_rk *pxpcs;
+	int ret;
+
+	pxpcs = xpcs_rk_create_data(pdev);
+	if (IS_ERR(pxpcs))
+		return PTR_ERR(pxpcs);
+
+	/*
+	 * The XPCS may be attached to a power domain (e.g. PD_PIPE). The domain
+	 * must be powered on before any register access, otherwise the SoC will
+	 * trigger a synchronous external abort (SError).
+	 *
+	 * Accessing the XPCS registers also requires a TX clock from the SerDes,
+	 * which is needed for the soft reset.
+	 */
+	ret = xpcs_rk_serdes_phy_init(pxpcs);
+	if (ret)
+		return ret;
+
+	ret = xpcs_rk_serdes_phy_poweron(pxpcs);
+	if (ret)
+		return ret;
+
+	ret = xpcs_rk_init_res(pxpcs);
+	if (ret)
+		return ret;
+
+	ret = xpcs_rk_init_clk(pxpcs);
+	if (ret)
+		return ret;
+
+	ret = xpcs_rk_init_bus(pxpcs);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static const struct of_device_id xpcs_rk_of_ids[] = {
+	{ .compatible = "rockchip,rk3568-xpcs" },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, xpcs_rk_of_ids);
+
+struct dw_xpcs *xpcs_rk_create(struct device *dev, struct device_node *np)
+{
+	struct platform_device *pdev;
+	struct device_node *pcs_np;
+	struct dw_xpcs_rk *pxpcs;
+	struct dw_xpcs *xpcs;
+	u32 port;
+
+	if (!of_device_is_available(np))
+		return ERR_PTR(-ENODEV);
+
+	if (of_property_read_u32(np, "reg", &port))
+		return ERR_PTR(-EINVAL);
+
+	if (!xpcs_rk_mdio_addr_validate((int)port))
+		return ERR_PTR(-EINVAL);
+
+	/* The XPCS pdev is attached to the parent node */
+	pcs_np = of_get_parent(np);
+	if (!pcs_np)
+		return ERR_PTR(-ENODEV);
+
+	if (!of_device_is_available(pcs_np)) {
+		of_node_put(pcs_np);
+		return ERR_PTR(-ENODEV);
+	}
+
+	if (!of_match_node(xpcs_rk_of_ids, pcs_np)) {
+		of_node_put(pcs_np);
+		return ERR_PTR(-EINVAL);
+	}
+
+	pdev = of_find_device_by_node(pcs_np);
+	of_node_put(pcs_np);
+	if (!pdev)
+		return ERR_PTR(-EPROBE_DEFER);
+
+	/*
+	 * Establish the device link before touching the supplier's drvdata.
+	 * device_link_add() does not fail on a supplier that is unbinding;
+	 * it creates the link in DL_STATE_SUPPLIER_UNBIND. What keeps the
+	 * drvdata valid afterwards is the link itself: once the supplier is
+	 * confirmed bound below, the link is in DL_STATE_CONSUMER_PROBE,
+	 * which makes device_links_unbind_consumers() wait for this probe
+	 * to finish before the supplier can be unbound.
+	 *
+	 * device_lock() plus device_is_bound() are used only to make the
+	 * "supplier is bound" check atomic with reading the drvdata; they
+	 * do not carry the protection past the unlock.
+	 *
+	 * The link is released automatically when the consumer device is
+	 * destroyed (DL_FLAG_AUTOREMOVE_CONSUMER), so no explicit
+	 * device_link_remove() is needed on the failure paths.
+	 */
+	if (!device_link_add(dev, &pdev->dev, DL_FLAG_AUTOREMOVE_CONSUMER)) {
+		put_device(&pdev->dev);
+		return ERR_PTR(-EPROBE_DEFER);
+	}
+
+	device_lock(&pdev->dev);
+	if (!device_is_bound(&pdev->dev)) {
+		device_unlock(&pdev->dev);
+		put_device(&pdev->dev);
+		return ERR_PTR(-EPROBE_DEFER);
+	}
+	device_unlock(&pdev->dev);
+
+	pxpcs = platform_get_drvdata(pdev);
+	if (!pxpcs || !pxpcs->bus) {
+		put_device(&pdev->dev);
+		return ERR_PTR(-EPROBE_DEFER);
+	}
+
+	xpcs = xpcs_create_mdiodev(pxpcs->bus, (int)port);
+	if (IS_ERR(xpcs)) {
+		put_device(&pdev->dev);
+		return xpcs;
+	}
+
+	xpcs_config_eee_mult_fact(xpcs, pxpcs->eee_mult_fact);
+	put_device(&pdev->dev);
+	return xpcs;
+}
+EXPORT_SYMBOL_GPL(xpcs_rk_create);
+
+static int xpcs_rk_pm_runtime_suspend(struct device *dev)
+{
+	struct dw_xpcs_rk *pxpcs = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(pxpcs->csr_clk);
+
+	return 0;
+}
+
+static int xpcs_rk_pm_runtime_resume(struct device *dev)
+{
+	struct dw_xpcs_rk *pxpcs = dev_get_drvdata(dev);
+
+	return clk_prepare_enable(pxpcs->csr_clk);
+}
+
+static DEFINE_RUNTIME_DEV_PM_OPS(xpcs_rk_pm_ops,
+			   xpcs_rk_pm_runtime_suspend,
+			   xpcs_rk_pm_runtime_resume,
+			   NULL);
+
+static struct platform_driver xpcs_rk_driver = {
+	.probe = xpcs_rk_probe,
+	.driver = {
+		.name = "rk_xpcs-dwxpcs",
+		.pm = pm_ptr(&xpcs_rk_pm_ops),
+		.of_match_table = xpcs_rk_of_ids,
+	},
+};
+module_platform_driver(xpcs_rk_driver);
+
+MODULE_DESCRIPTION("Rockchip XPCS platform device driver");
+MODULE_AUTHOR("Coia Prant <coiaprant@gmail.com>");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/pcs/pcs-xpcs-rk.h b/include/linux/pcs/pcs-xpcs-rk.h
new file mode 100644
index 0000000000000..28723d5bd75cc
--- /dev/null
+++ b/include/linux/pcs/pcs-xpcs-rk.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __LINUX_PCS_XPCS_ROCKCHIP_H
+#define __LINUX_PCS_XPCS_ROCKCHIP_H
+
+#include <linux/device.h>
+#include <linux/of.h>
+#include <linux/pcs/pcs-xpcs.h>
+
+struct dw_xpcs *xpcs_rk_create(struct device *dev, struct device_node *np);
+
+#endif /* __LINUX_PCS_XPCS_ROCKCHIP_H */
-- 
2.47.3

[PATCH net-next v8 08/11] dt-bindings: net: rockchip-dwmac: document pcs-handle

[Coia Prant]

The Rockchip GMAC binding needs to describe the PCS reference used by
the SGMII support added later in this series. The property will be
parsed by rk_pcs_init(), and a missing phandle fails the probe. Add it
and require it when phy-mode is "sgmii" on rockchip,rk3568-gmac, the
only SoC in this binding that has SGMII support.

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 .../bindings/net/rockchip-dwmac.yaml           | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml b/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml
index 80c252845349c..bb7540e838033 100644
--- a/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml
+++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.yaml
@@ -120,6 +120,12 @@ properties:
     maximum: 0x7F
     default: 0x10
 
+  pcs-handle:
+    description:
+      Specifies a reference to a node representing the PCS device
+      connected to this GMAC. Required when phy-mode is "sgmii".
+    maxItems: 1
+
   phy-supply:
     description: PHY regulator
 
@@ -159,6 +165,18 @@ allOf:
         clocks:
           minItems: 5
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: rockchip,rk3568-gmac
+        phy-mode:
+          contains:
+            const: sgmii
+    then:
+      required:
+        - pcs-handle
+
 unevaluatedProperties: false
 
 examples:
-- 
2.47.3

[PATCH net-next v8 09/11] net: stmmac: dwmac-rk: add SGMII support for RK3568

[Coia Prant]

The RK3568 SoC integrates a Synopsys DesignWare XPCS that can be
connected to GMAC0 or GMAC1 in SGMII mode.  Add the necessary glue
logic to support this configuration.

The current dwmac-rk driver does not support SGMII mode.  SGMII
requires a PCS to handle auto-negotiation and link state reporting,
but the existing driver only supports RGMII and RMII.

Add a set_to_sgmii() callback to configure the GMAC GRF register for
SGMII mode (bit 7 set, interface selection bits 4:6 ignored when set).
Also add a set_to_rmii() callback for rk3568 to explicitly clear bit 7,
since the new SGMII path leaves it set and the RMII branch previously
relied on the SoC reset value.

Provide pcs_init/pcs_exit callbacks to create/destroy the XPCS via
xpcs_rk_create() from the Rockchip XPCS platform driver, and a
select_pcs callback to return the XPCS to phylink. SGMII is not added
to rk_get_interfaces(): it comes from the XPCS's own
supported_interfaces, merged by stmmac_phylink_setup().

The SerDes PHY and the PD_PIPE power domain are owned by the XPCS
driver rather than managed through the stmmac
serdes_poweron/serdes_poweroff callbacks, which are legacy and meant
for single-MAC platforms. On RK3568 the XPCS is the natural owner of
the shared SerDes.

DWMAC_ROCKCHIP selects PCS_XPCS_ROCKCHIP. PCS_XPCS itself is already
selected by STMMAC_ETH, and PM is selected by ARCH_ROCKCHIP, so no
further selects are needed.

Reorder rk_gmac_powerup() so that gmac_clk_enable() is called before
the SGMII check.  The SGMII path skips rk_get_phy_intf_sel(), so the
clock must be enabled earlier to cover all register accesses in that
path.  While at it, unify the error unwinding into a single
clk_disable label and add error handling for the default (unhandled
interface) case.

SGMII In-band vs Out-of-band
============================
On RK3568, the MAC clock is fixed at 125 MHz and cannot be dynamically
changed by the stmmac core's set_clk_tx_rate callback.  In-band mode
works because the PCS handles rate adaptation internally.  Out-of-band
mode does not work because the MAC would need to change the clock rate
to 125/12.5/1.25 MHz for 1000/100/10 Mbps respectively, and the clock
is fixed.

Enable default_an_inband for SGMII and disable the generic stmmac
set_clk_tx_rate callback.  This forces phylink to use in-band mode,
where the PCS is responsible for speed/duplex negotiation.

Note that default_an_inband can be overridden by a fixed-link node,
and phylink may also fall back to out-of-band if the PHY does not
support in-band signalling.  Out-of-band SGMII is not supported by
this driver: the MAC clock would stay at 125 MHz for 10/100 Mbps,
giving working TX but failing RX.  Boards must use in-band mode
(managed = "in-band-status" or an in-band capable PHY).

Link: https://dl.radxa.com/rock3/docs/hw/datasheet/Rockchip%20RK3568%20TRM%20Part1%20V1.1-20210301.pdf (Page 386)
Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 drivers/net/ethernet/stmicro/stmmac/Kconfig   |   1 +
 .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 130 +++++++++++++++---
 2 files changed, 111 insertions(+), 20 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
index e3dd5adda5aca..5088acc06982e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
+++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
@@ -170,6 +170,7 @@ config DWMAC_ROCKCHIP
 	default ARCH_ROCKCHIP
 	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
 	select MFD_SYSCON
+	select PCS_XPCS_ROCKCHIP
 	help
 	  Support for Ethernet controller on Rockchip RK3288 SoC.
 
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
index 8d7042e689261..88f09014e3a69 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
@@ -20,6 +20,7 @@
 #include <linux/delay.h>
 #include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
+#include <linux/pcs/pcs-xpcs-rk.h>
 #include <linux/pm_runtime.h>
 
 #include "stmmac_platform.h"
@@ -47,6 +48,7 @@ struct rk_gmac_ops {
 	void (*set_to_rgmii)(struct rk_priv_data *bsp_priv,
 			     int tx_delay, int rx_delay);
 	void (*set_to_rmii)(struct rk_priv_data *bsp_priv);
+	void (*set_to_sgmii)(struct rk_priv_data *bsp_priv);
 	int (*set_speed)(struct rk_priv_data *bsp_priv,
 			 phy_interface_t interface, int speed);
 	void (*integrated_phy_powerup)(struct rk_priv_data *bsp_priv);
@@ -63,6 +65,7 @@ struct rk_gmac_ops {
 	bool clock_grf_reg_in_php;
 	bool supports_rgmii;
 	bool supports_rmii;
+	bool supports_sgmii;
 	bool php_grf_required;
 	bool regs_valid;
 	u32 regs[];
@@ -98,6 +101,7 @@ struct rk_priv_data {
 	bool integrated_phy;
 	bool supports_rgmii;
 	bool supports_rmii;
+	bool supports_sgmii;
 
 	struct clk_bulk_data *clks;
 	int num_clks;
@@ -809,6 +813,8 @@ static const struct rk_gmac_ops rk3528_ops = {
 #define RK3568_GRF_GMAC1_CON1		0x038c
 
 /* RK3568_GRF_GMAC0_CON1 && RK3568_GRF_GMAC1_CON1 */
+#define RK3568_GMAC_MODE_RMII_RGMII		GRF_CLR_BIT(7)
+#define RK3568_GMAC_MODE_SGMII_QSGMII		GRF_BIT(7)
 #define RK3568_GMAC_FLOW_CTRL			GRF_BIT(3)
 #define RK3568_GMAC_FLOW_CTRL_CLR		GRF_CLR_BIT(3)
 #define RK3568_GMAC_RXCLK_DLY_ENABLE		GRF_BIT(1)
@@ -836,6 +842,16 @@ static int rk3568_init(struct rk_priv_data *bsp_priv)
 	}
 }
 
+static void rk3568_set_to_rmii(struct rk_priv_data *bsp_priv)
+{
+	u32 con1;
+
+	con1 = (bsp_priv->id == 1) ? RK3568_GRF_GMAC1_CON1 :
+				     RK3568_GRF_GMAC0_CON1;
+
+	regmap_write(bsp_priv->grf, con1, RK3568_GMAC_MODE_RMII_RGMII);
+}
+
 static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
 				int tx_delay, int rx_delay)
 {
@@ -851,19 +867,31 @@ static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
 		     RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
 
 	regmap_write(bsp_priv->grf, con1,
+		     RK3568_GMAC_MODE_RMII_RGMII |
 		     RK3568_GMAC_RXCLK_DLY_ENABLE |
 		     RK3568_GMAC_TXCLK_DLY_ENABLE);
 }
 
+static void rk3568_set_to_sgmii(struct rk_priv_data *bsp_priv)
+{
+	u32 con1;
+
+	con1 = (bsp_priv->id == 1) ? RK3568_GRF_GMAC1_CON1 :
+				     RK3568_GRF_GMAC0_CON1;
+
+	regmap_write(bsp_priv->grf, con1, RK3568_GMAC_MODE_SGMII_QSGMII);
+}
+
 static const struct rk_gmac_ops rk3568_ops = {
 	.init = rk3568_init,
+	.set_to_rmii = rk3568_set_to_rmii,
 	.set_to_rgmii = rk3568_set_to_rgmii,
+	.set_to_sgmii = rk3568_set_to_sgmii,
+
 	.set_speed = rk_set_clk_mac_speed,
 
 	.gmac_phy_intf_sel_mask = GENMASK_U16(6, 4),
 
-	.supports_rmii = true,
-
 	.regs_valid = true,
 	.regs = {
 		0xfe2a0000, /* gmac0 */
@@ -1208,6 +1236,43 @@ static void rk_phy_powerdown(struct rk_priv_data *bsp_priv)
 		dev_err(bsp_priv->dev, "fail to disable phy-supply\n");
 }
 
+static int rk_pcs_init(struct stmmac_priv *priv)
+{
+	struct device_node *np = priv->device->of_node;
+	struct device_node *pcs_node;
+	struct dw_xpcs *xpcs;
+
+	pcs_node = of_parse_phandle(np, "pcs-handle", 0);
+	if (!pcs_node)
+		return -ENODEV;
+
+	xpcs = xpcs_rk_create(priv->device, pcs_node);
+	of_node_put(pcs_node);
+	if (IS_ERR(xpcs))
+		return PTR_ERR(xpcs);
+
+	priv->hw->xpcs = xpcs;
+	return 0;
+}
+
+static void rk_pcs_exit(struct stmmac_priv *priv)
+{
+	if (!priv->hw->xpcs)
+		return;
+
+	xpcs_destroy(priv->hw->xpcs);
+	priv->hw->xpcs = NULL;
+}
+
+static struct phylink_pcs *rk_select_pcs(struct stmmac_priv *priv,
+					 phy_interface_t interface)
+{
+	if (!priv->hw->xpcs)
+		return NULL;
+
+	return xpcs_to_phylink_pcs(priv->hw->xpcs);
+}
+
 static struct rk_priv_data *rk_gmac_setup(struct platform_device *pdev,
 					  struct plat_stmmacenet_data *plat,
 					  const struct rk_gmac_ops *ops)
@@ -1330,6 +1395,7 @@ static struct rk_priv_data *rk_gmac_setup(struct platform_device *pdev,
 
 	bsp_priv->supports_rgmii = ops->supports_rgmii || !!ops->set_to_rgmii;
 	bsp_priv->supports_rmii = ops->supports_rmii || !!ops->set_to_rmii;
+	bsp_priv->supports_sgmii = ops->supports_sgmii || !!ops->set_to_sgmii;
 
 	if (ops->init) {
 		ret = ops->init(bsp_priv);
@@ -1361,6 +1427,10 @@ static int rk_gmac_check_ops(struct rk_priv_data *bsp_priv)
 		if (!bsp_priv->supports_rmii)
 			return -EINVAL;
 		break;
+	case PHY_INTERFACE_MODE_SGMII:
+		if (!bsp_priv->supports_sgmii)
+			return -EINVAL;
+		break;
 	default:
 		dev_err(bsp_priv->dev,
 			"unsupported interface %d", bsp_priv->phy_iface);
@@ -1379,16 +1449,19 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 	if (ret)
 		return ret;
 
+	ret = gmac_clk_enable(bsp_priv, true);
+	if (ret)
+		return ret;
+
+	if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_SGMII)
+		goto set_mode;
+
 	ret = rk_get_phy_intf_sel(bsp_priv->phy_iface);
 	if (ret < 0)
-		return ret;
+		goto clk_disable;
 
 	intf = ret;
 
-	ret = gmac_clk_enable(bsp_priv, true);
-	if (ret)
-		return ret;
-
 	if (bsp_priv->gmac_phy_intf_sel_mask ||
 	    bsp_priv->gmac_rmii_mode_mask) {
 		/* If defined, encode the phy_intf_sel value */
@@ -1399,10 +1472,8 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 				      bsp_priv->gmac_rmii_mode_mask);
 
 		ret = rk_write_gmac_grf_reg(bsp_priv, val);
-		if (ret < 0) {
-			gmac_clk_enable(bsp_priv, false);
-			return ret;
-		}
+		if (ret < 0)
+			goto clk_disable;
 	}
 
 	if (bsp_priv->clock.rmii_mode_mask) {
@@ -1410,13 +1481,12 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 				     bsp_priv->clock.rmii_mode_mask);
 
 		ret = rk_write_clock_grf_reg(bsp_priv, val);
-		if (ret < 0) {
-			gmac_clk_enable(bsp_priv, false);
-			return ret;
-		}
+		if (ret < 0)
+			goto clk_disable;
 	}
 
-	/*rmii or rgmii*/
+set_mode:
+	/* rmii, rgmii, sgmii */
 	switch (bsp_priv->phy_iface) {
 	case PHY_INTERFACE_MODE_RGMII:
 		dev_info(dev, "init for RGMII\n");
@@ -1447,15 +1517,20 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 		if (bsp_priv->ops->set_to_rmii)
 			bsp_priv->ops->set_to_rmii(bsp_priv);
 		break;
+	case PHY_INTERFACE_MODE_SGMII:
+		dev_info(dev, "init for SGMII\n");
+		if (bsp_priv->ops->set_to_sgmii)
+			bsp_priv->ops->set_to_sgmii(bsp_priv);
+		break;
 	default:
 		dev_err(dev, "NO interface defined!\n");
+		ret = -EINVAL;
+		goto clk_disable;
 	}
 
 	ret = rk_phy_powerup(bsp_priv);
-	if (ret) {
-		gmac_clk_enable(bsp_priv, false);
-		return ret;
-	}
+	if (ret)
+		goto clk_disable;
 
 	pm_runtime_get_sync(dev);
 
@@ -1463,6 +1538,10 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
 		bsp_priv->ops->integrated_phy_powerup(bsp_priv);
 
 	return 0;
+
+clk_disable:
+	gmac_clk_enable(bsp_priv, false);
+	return ret;
 }
 
 static void rk_gmac_powerdown(struct rk_priv_data *gmac)
@@ -1602,6 +1681,17 @@ static int rk_gmac_probe(struct platform_device *pdev)
 	plat_dat->suspend = rk_gmac_suspend;
 	plat_dat->resume = rk_gmac_resume;
 
+	if (plat_dat->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+		/* SGMII clock always runs at 125 MHz */
+		plat_dat->set_clk_tx_rate = NULL;
+
+		/* SGMII requires a PCS */
+		plat_dat->default_an_inband = true;
+		plat_dat->pcs_init = rk_pcs_init;
+		plat_dat->pcs_exit = rk_pcs_exit;
+		plat_dat->select_pcs = rk_select_pcs;
+	}
+
 	plat_dat->bsp_priv = rk_gmac_setup(pdev, plat_dat, data);
 	if (IS_ERR(plat_dat->bsp_priv))
 		return PTR_ERR(plat_dat->bsp_priv);
-- 
2.47.3

Re: [PATCH net-next v8 09/11] net: stmmac: dwmac-rk: add SGMII support for RK3568

[Maxime Chevallier]

Hi,

On 9/19/26 14:51, Coia Prant wrote:
> The RK3568 SoC integrates a Synopsys DesignWare XPCS that can be
> connected to GMAC0 or GMAC1 in SGMII mode.  Add the necessary glue
> logic to support this configuration.
> 
> The current dwmac-rk driver does not support SGMII mode.  SGMII
> requires a PCS to handle auto-negotiation and link state reporting,
> but the existing driver only supports RGMII and RMII.
> 
> Add a set_to_sgmii() callback to configure the GMAC GRF register for
> SGMII mode (bit 7 set, interface selection bits 4:6 ignored when set).
> Also add a set_to_rmii() callback for rk3568 to explicitly clear bit 7,
> since the new SGMII path leaves it set and the RMII branch previously
> relied on the SoC reset value.
> 
> Provide pcs_init/pcs_exit callbacks to create/destroy the XPCS via
> xpcs_rk_create() from the Rockchip XPCS platform driver, and a
> select_pcs callback to return the XPCS to phylink. SGMII is not added
> to rk_get_interfaces(): it comes from the XPCS's own
> supported_interfaces, merged by stmmac_phylink_setup().
> 
> The SerDes PHY and the PD_PIPE power domain are owned by the XPCS
> driver rather than managed through the stmmac
> serdes_poweron/serdes_poweroff callbacks, which are legacy and meant
> for single-MAC platforms. On RK3568 the XPCS is the natural owner of
> the shared SerDes.
> 
> DWMAC_ROCKCHIP selects PCS_XPCS_ROCKCHIP. PCS_XPCS itself is already
> selected by STMMAC_ETH, and PM is selected by ARCH_ROCKCHIP, so no
> further selects are needed.
> 
> Reorder rk_gmac_powerup() so that gmac_clk_enable() is called before
> the SGMII check.  The SGMII path skips rk_get_phy_intf_sel(), so the
> clock must be enabled earlier to cover all register accesses in that
> path.  While at it, unify the error unwinding into a single
> clk_disable label and add error handling for the default (unhandled
> interface) case.
> 
> SGMII In-band vs Out-of-band
> ============================
> On RK3568, the MAC clock is fixed at 125 MHz and cannot be dynamically
> changed by the stmmac core's set_clk_tx_rate callback.  In-band mode
> works because the PCS handles rate adaptation internally.  Out-of-band
> mode does not work because the MAC would need to change the clock rate
> to 125/12.5/1.25 MHz for 1000/100/10 Mbps respectively, and the clock
> is fixed.
> 
> Enable default_an_inband for SGMII and disable the generic stmmac
> set_clk_tx_rate callback.  This forces phylink to use in-band mode,
> where the PCS is responsible for speed/duplex negotiation.
> 
> Note that default_an_inband can be overridden by a fixed-link node,
> and phylink may also fall back to out-of-band if the PHY does not
> support in-band signalling.  Out-of-band SGMII is not supported by
> this driver: the MAC clock would stay at 125 MHz for 10/100 Mbps,
> giving working TX but failing RX.  Boards must use in-band mode
> (managed = "in-band-status" or an in-band capable PHY).
> 
> Link: https://dl.radxa.com/rock3/docs/hw/datasheet/Rockchip%20RK3568%20TRM%20Part1%20V1.1-20210301.pdf (Page 386)
> Signed-off-by: Coia Prant <coiaprant@gmail.com>

Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com

Maxime

> ---
>  drivers/net/ethernet/stmicro/stmmac/Kconfig   |   1 +
>  .../net/ethernet/stmicro/stmmac/dwmac-rk.c    | 130 +++++++++++++++---
>  2 files changed, 111 insertions(+), 20 deletions(-)
> 
> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> index e3dd5adda5aca..5088acc06982e 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> @@ -170,6 +170,7 @@ config DWMAC_ROCKCHIP
>  	default ARCH_ROCKCHIP
>  	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
>  	select MFD_SYSCON
> +	select PCS_XPCS_ROCKCHIP
>  	help
>  	  Support for Ethernet controller on Rockchip RK3288 SoC.
>  
> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> index 8d7042e689261..88f09014e3a69 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c
> @@ -20,6 +20,7 @@
>  #include <linux/delay.h>
>  #include <linux/mfd/syscon.h>
>  #include <linux/regmap.h>
> +#include <linux/pcs/pcs-xpcs-rk.h>
>  #include <linux/pm_runtime.h>
>  
>  #include "stmmac_platform.h"
> @@ -47,6 +48,7 @@ struct rk_gmac_ops {
>  	void (*set_to_rgmii)(struct rk_priv_data *bsp_priv,
>  			     int tx_delay, int rx_delay);
>  	void (*set_to_rmii)(struct rk_priv_data *bsp_priv);
> +	void (*set_to_sgmii)(struct rk_priv_data *bsp_priv);
>  	int (*set_speed)(struct rk_priv_data *bsp_priv,
>  			 phy_interface_t interface, int speed);
>  	void (*integrated_phy_powerup)(struct rk_priv_data *bsp_priv);
> @@ -63,6 +65,7 @@ struct rk_gmac_ops {
>  	bool clock_grf_reg_in_php;
>  	bool supports_rgmii;
>  	bool supports_rmii;
> +	bool supports_sgmii;
>  	bool php_grf_required;
>  	bool regs_valid;
>  	u32 regs[];
> @@ -98,6 +101,7 @@ struct rk_priv_data {
>  	bool integrated_phy;
>  	bool supports_rgmii;
>  	bool supports_rmii;
> +	bool supports_sgmii;
>  
>  	struct clk_bulk_data *clks;
>  	int num_clks;
> @@ -809,6 +813,8 @@ static const struct rk_gmac_ops rk3528_ops = {
>  #define RK3568_GRF_GMAC1_CON1		0x038c
>  
>  /* RK3568_GRF_GMAC0_CON1 && RK3568_GRF_GMAC1_CON1 */
> +#define RK3568_GMAC_MODE_RMII_RGMII		GRF_CLR_BIT(7)
> +#define RK3568_GMAC_MODE_SGMII_QSGMII		GRF_BIT(7)
>  #define RK3568_GMAC_FLOW_CTRL			GRF_BIT(3)
>  #define RK3568_GMAC_FLOW_CTRL_CLR		GRF_CLR_BIT(3)
>  #define RK3568_GMAC_RXCLK_DLY_ENABLE		GRF_BIT(1)
> @@ -836,6 +842,16 @@ static int rk3568_init(struct rk_priv_data *bsp_priv)
>  	}
>  }
>  
> +static void rk3568_set_to_rmii(struct rk_priv_data *bsp_priv)
> +{
> +	u32 con1;
> +
> +	con1 = (bsp_priv->id == 1) ? RK3568_GRF_GMAC1_CON1 :
> +				     RK3568_GRF_GMAC0_CON1;
> +
> +	regmap_write(bsp_priv->grf, con1, RK3568_GMAC_MODE_RMII_RGMII);
> +}
> +
>  static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
>  				int tx_delay, int rx_delay)
>  {
> @@ -851,19 +867,31 @@ static void rk3568_set_to_rgmii(struct rk_priv_data *bsp_priv,
>  		     RK3568_GMAC_CLK_TX_DL_CFG(tx_delay));
>  
>  	regmap_write(bsp_priv->grf, con1,
> +		     RK3568_GMAC_MODE_RMII_RGMII |
>  		     RK3568_GMAC_RXCLK_DLY_ENABLE |
>  		     RK3568_GMAC_TXCLK_DLY_ENABLE);
>  }
>  
> +static void rk3568_set_to_sgmii(struct rk_priv_data *bsp_priv)
> +{
> +	u32 con1;
> +
> +	con1 = (bsp_priv->id == 1) ? RK3568_GRF_GMAC1_CON1 :
> +				     RK3568_GRF_GMAC0_CON1;
> +
> +	regmap_write(bsp_priv->grf, con1, RK3568_GMAC_MODE_SGMII_QSGMII);
> +}
> +
>  static const struct rk_gmac_ops rk3568_ops = {
>  	.init = rk3568_init,
> +	.set_to_rmii = rk3568_set_to_rmii,
>  	.set_to_rgmii = rk3568_set_to_rgmii,
> +	.set_to_sgmii = rk3568_set_to_sgmii,
> +
>  	.set_speed = rk_set_clk_mac_speed,
>  
>  	.gmac_phy_intf_sel_mask = GENMASK_U16(6, 4),
>  
> -	.supports_rmii = true,
> -
>  	.regs_valid = true,
>  	.regs = {
>  		0xfe2a0000, /* gmac0 */
> @@ -1208,6 +1236,43 @@ static void rk_phy_powerdown(struct rk_priv_data *bsp_priv)
>  		dev_err(bsp_priv->dev, "fail to disable phy-supply\n");
>  }
>  
> +static int rk_pcs_init(struct stmmac_priv *priv)
> +{
> +	struct device_node *np = priv->device->of_node;
> +	struct device_node *pcs_node;
> +	struct dw_xpcs *xpcs;
> +
> +	pcs_node = of_parse_phandle(np, "pcs-handle", 0);
> +	if (!pcs_node)
> +		return -ENODEV;
> +
> +	xpcs = xpcs_rk_create(priv->device, pcs_node);
> +	of_node_put(pcs_node);
> +	if (IS_ERR(xpcs))
> +		return PTR_ERR(xpcs);
> +
> +	priv->hw->xpcs = xpcs;
> +	return 0;
> +}
> +
> +static void rk_pcs_exit(struct stmmac_priv *priv)
> +{
> +	if (!priv->hw->xpcs)
> +		return;
> +
> +	xpcs_destroy(priv->hw->xpcs);
> +	priv->hw->xpcs = NULL;
> +}
> +
> +static struct phylink_pcs *rk_select_pcs(struct stmmac_priv *priv,
> +					 phy_interface_t interface)
> +{
> +	if (!priv->hw->xpcs)
> +		return NULL;
> +
> +	return xpcs_to_phylink_pcs(priv->hw->xpcs);
> +}
> +
>  static struct rk_priv_data *rk_gmac_setup(struct platform_device *pdev,
>  					  struct plat_stmmacenet_data *plat,
>  					  const struct rk_gmac_ops *ops)
> @@ -1330,6 +1395,7 @@ static struct rk_priv_data *rk_gmac_setup(struct platform_device *pdev,
>  
>  	bsp_priv->supports_rgmii = ops->supports_rgmii || !!ops->set_to_rgmii;
>  	bsp_priv->supports_rmii = ops->supports_rmii || !!ops->set_to_rmii;
> +	bsp_priv->supports_sgmii = ops->supports_sgmii || !!ops->set_to_sgmii;
>  
>  	if (ops->init) {
>  		ret = ops->init(bsp_priv);
> @@ -1361,6 +1427,10 @@ static int rk_gmac_check_ops(struct rk_priv_data *bsp_priv)
>  		if (!bsp_priv->supports_rmii)
>  			return -EINVAL;
>  		break;
> +	case PHY_INTERFACE_MODE_SGMII:
> +		if (!bsp_priv->supports_sgmii)
> +			return -EINVAL;
> +		break;
>  	default:
>  		dev_err(bsp_priv->dev,
>  			"unsupported interface %d", bsp_priv->phy_iface);
> @@ -1379,16 +1449,19 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
>  	if (ret)
>  		return ret;
>  
> +	ret = gmac_clk_enable(bsp_priv, true);
> +	if (ret)
> +		return ret;
> +
> +	if (bsp_priv->phy_iface == PHY_INTERFACE_MODE_SGMII)
> +		goto set_mode;
> +
>  	ret = rk_get_phy_intf_sel(bsp_priv->phy_iface);
>  	if (ret < 0)
> -		return ret;
> +		goto clk_disable;
>  
>  	intf = ret;
>  
> -	ret = gmac_clk_enable(bsp_priv, true);
> -	if (ret)
> -		return ret;
> -
>  	if (bsp_priv->gmac_phy_intf_sel_mask ||
>  	    bsp_priv->gmac_rmii_mode_mask) {
>  		/* If defined, encode the phy_intf_sel value */
> @@ -1399,10 +1472,8 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
>  				      bsp_priv->gmac_rmii_mode_mask);
>  
>  		ret = rk_write_gmac_grf_reg(bsp_priv, val);
> -		if (ret < 0) {
> -			gmac_clk_enable(bsp_priv, false);
> -			return ret;
> -		}
> +		if (ret < 0)
> +			goto clk_disable;
>  	}
>  
>  	if (bsp_priv->clock.rmii_mode_mask) {
> @@ -1410,13 +1481,12 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
>  				     bsp_priv->clock.rmii_mode_mask);
>  
>  		ret = rk_write_clock_grf_reg(bsp_priv, val);
> -		if (ret < 0) {
> -			gmac_clk_enable(bsp_priv, false);
> -			return ret;
> -		}
> +		if (ret < 0)
> +			goto clk_disable;
>  	}
>  
> -	/*rmii or rgmii*/
> +set_mode:
> +	/* rmii, rgmii, sgmii */
>  	switch (bsp_priv->phy_iface) {
>  	case PHY_INTERFACE_MODE_RGMII:
>  		dev_info(dev, "init for RGMII\n");
> @@ -1447,15 +1517,20 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
>  		if (bsp_priv->ops->set_to_rmii)
>  			bsp_priv->ops->set_to_rmii(bsp_priv);
>  		break;
> +	case PHY_INTERFACE_MODE_SGMII:
> +		dev_info(dev, "init for SGMII\n");
> +		if (bsp_priv->ops->set_to_sgmii)
> +			bsp_priv->ops->set_to_sgmii(bsp_priv);
> +		break;
>  	default:
>  		dev_err(dev, "NO interface defined!\n");
> +		ret = -EINVAL;
> +		goto clk_disable;
>  	}
>  
>  	ret = rk_phy_powerup(bsp_priv);
> -	if (ret) {
> -		gmac_clk_enable(bsp_priv, false);
> -		return ret;
> -	}
> +	if (ret)
> +		goto clk_disable;
>  
>  	pm_runtime_get_sync(dev);
>  
> @@ -1463,6 +1538,10 @@ static int rk_gmac_powerup(struct rk_priv_data *bsp_priv)
>  		bsp_priv->ops->integrated_phy_powerup(bsp_priv);
>  
>  	return 0;
> +
> +clk_disable:
> +	gmac_clk_enable(bsp_priv, false);
> +	return ret;
>  }
>  
>  static void rk_gmac_powerdown(struct rk_priv_data *gmac)
> @@ -1602,6 +1681,17 @@ static int rk_gmac_probe(struct platform_device *pdev)
>  	plat_dat->suspend = rk_gmac_suspend;
>  	plat_dat->resume = rk_gmac_resume;
>  
> +	if (plat_dat->phy_interface == PHY_INTERFACE_MODE_SGMII) {
> +		/* SGMII clock always runs at 125 MHz */
> +		plat_dat->set_clk_tx_rate = NULL;
> +
> +		/* SGMII requires a PCS */
> +		plat_dat->default_an_inband = true;
> +		plat_dat->pcs_init = rk_pcs_init;
> +		plat_dat->pcs_exit = rk_pcs_exit;
> +		plat_dat->select_pcs = rk_select_pcs;
> +	}
> +
>  	plat_dat->bsp_priv = rk_gmac_setup(pdev, plat_dat, data);
>  	if (IS_ERR(plat_dat->bsp_priv))
>  		return PTR_ERR(plat_dat->bsp_priv);

[PATCH net-next v8 10/11] arm64: dts: rockchip: rk3568-photonicat: enable SGMII LAN port

[Coia Prant]

The Ariaboard Photonicat has a Motorcomm YT8521SC Gigabit Ethernet PHY
connected to GMAC0 via XPCS SGMII.  Enable the necessary nodes to make
this port functional.

Add rockchip,sgmii-mac-sel = <0> to the already enabled combphy2,
to route the SGMII interface to GMAC0.  RK3568 has three Combo PHYs
that can carry SGMII; which one is wired to the XPCS is a board-level
choice, and Photonicat uses combphy2.

Enable the xpcs node and its port 0 sub-node, referencing combphy2
as the SerDes PHY.

Add the mdio0 node with the YT8521SC PHY at address 3, including its
reset GPIO and LED configuration.  Also add LED configuration for the
existing RGMII PHY on mdio1 for consistency.

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 .../boot/dts/rockchip/rk3568-photonicat.dts   | 74 ++++++++++++++++++-
 1 file changed, 72 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts b/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
index 58c1052ba8ef3..fdaa4a2a4328b 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
@@ -3,6 +3,7 @@
 /dts-v1/;
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/rockchip.h>
 #include <dt-bindings/soc/rockchip,vop2.h>
 #include "rk3568.dtsi"
@@ -241,6 +242,7 @@ &combphy1 {
 };
 
 &combphy2 {
+	rockchip,sgmii-mac-sel = <0>;
 	status = "okay";
 };
 
@@ -260,9 +262,18 @@ &cpu3 {
 	cpu-supply = <&vdd_cpu>;
 };
 
-/* Motorcomm YT8521SC LAN port (require SGMII) */
+/* Motorcomm YT8521SC LAN port */
 &gmac0 {
-	status = "disabled";
+	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>;
+	assigned-clock-parents = <&clk_gmac0_xpcs_mii>;
+	managed = "in-band-status";
+	pcs-handle = <&xpcs_mii0>;
+	phy-handle = <&sgmii_phy>;
+	phy-mode = "sgmii";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_miim>;
+	status = "okay";
 };
 
 /* Motorcomm YT8521SC WAN port */
@@ -341,6 +352,36 @@ &i2s0_8ch {
 	status = "okay";
 };
 
+&mdio0 {
+	sgmii_phy: ethernet-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x3>;
+		max-speed = <1000>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio3 RK_PC6 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+		};
+	};
+};
+
 &mdio1 {
 	rgmii_phy: ethernet-phy@3 {
 		compatible = "ethernet-phy-ieee802.3-c22";
@@ -350,6 +391,25 @@ rgmii_phy: ethernet-phy@3 {
 		reset-gpios = <&gpio4 RK_PC0 GPIO_ACTIVE_LOW>;
 		rx-internal-delay-ps = <1500>;
 		tx-internal-delay-ps = <1500>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_WAN;
+				default-state = "keep";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_WAN;
+				default-state = "keep";
+			};
+		};
 	};
 };
 
@@ -586,3 +646,13 @@ &xin32k {
 	pinctrl-names = "default";
 	pinctrl-0 = <&clk32k_out1>;
 };
+
+&xpcs {
+	phys = <&combphy2 PHY_TYPE_SGMII>;
+	phy-names = "serdes";
+	status = "okay";
+};
+
+&xpcs_mii0 {
+	status = "okay";
+};
-- 
2.47.3

[PATCH net-next v8 11/11] MAINTAINERS: add entry for Rockchip XPCS driver

[Coia Prant]

Add a MAINTAINERS entry for the Rockchip RK3568 XPCS platform driver
and its device tree binding.

Include the relevant mailing lists (netdev and linux-rockchip) so that
future patches are properly distributed.

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 MAINTAINERS | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 3b2eb2a7a89a8..f53a519da6298 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -23739,6 +23739,15 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/sound/rockchip,rk3576-sai.yaml
 F:	sound/soc/rockchip/rockchip_sai.*
 
+ROCKCHIP XPCS DRIVER
+M:	Coia Prant <coiaprant@gmail.com>
+L:	netdev@vger.kernel.org
+L:	linux-rockchip@lists.infradead.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/net/pcs/rockchip,rk3568-xpcs.yaml
+F:	drivers/net/pcs/pcs-xpcs-rk.c
+F:	include/linux/pcs/pcs-xpcs-rk.h
+
 ROCKER DRIVER
 M:	Jiri Pirko <jiri@resnulli.us>
 L:	netdev@vger.kernel.org
-- 
2.47.3