[PATCH net v2 0/5] net: bcmgenet: Collection of bug fixes

[PATCH net v2 0/5] net: bcmgenet: Collection of bug fixes

[Florian Fainelli]

This patch series contains a collection of bug fixes found during a
LLM-assisted coding session.

Changes in v2:

- corrected Fixes commit for "net: bcmgenet: do not skip WoL power up on
  GENET V1"
- dropped unnecessary patches

Florian Fainelli (5):
  net: bcmgenet: fix 64-bit RTNL stats reading in ethtool on 32-bit
    systems
  net: bcmgenet: initialize u64 stats seq counter for all queues
  net: bcmgenet: do not skip WoL power up on GENET V1
  net: bcmgenet: validate Ethernet address in bcmgenet_set_mac_addr
  net: bcmgenet: mask DMA_TIMEOUT_MASK when reading DMA_RING0_TIMEOUT

 .../net/ethernet/broadcom/genet/bcmgenet.c    | 28 +++++++++++--------
 1 file changed, 17 insertions(+), 11 deletions(-)

-- 
2.34.1

[PATCH net v2 1/5] net: bcmgenet: fix 64-bit RTNL stats reading in ethtool on 32-bit systems

[Florian Fainelli]

When bcmgenet was converted to 64-bit statistics, STAT_RTNL members were
switched to point into struct rtnl_link_stats64, whose fields are 64-bit
(__u64) regardless of architecture.

However, bcmgenet_get_ethtool_stats() retained a legacy check:
  if (sizeof(unsigned long) != sizeof(u32) &&
      s->stat_sizeof == sizeof(unsigned long))

On 32-bit systems, sizeof(unsigned long) == sizeof(u32), causing this
condition to evaluate to false. As a result, 64-bit RTNL stats fields were
read via *(u32 *)p. On 32-bit Big-Endian systems (such as MIPS BE), this
reads the high 32 bits and returns 0 until the counter exceeds 4GB; on
32-bit Little-Endian systems (such as 32-bit ARM), the value is truncated
to 32 bits.

Fix this by checking if s->stat_sizeof == sizeof(u64) so 64-bit fields are
always read as 64-bit values.

Fixes: 59aa6e3072aa ("net: bcmgenet: switch to use 64bit statistics")
Assisted-by: LLM
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
---
 drivers/net/ethernet/broadcom/genet/bcmgenet.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index b916080f4ff1..7b089de9484e 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -1346,9 +1346,8 @@ static void bcmgenet_get_ethtool_stats(struct net_device *dev,
 				p = (char *)&stats64;
 
 			p += s->stat_offset;
-			if (sizeof(unsigned long) != sizeof(u32) &&
-				s->stat_sizeof == sizeof(unsigned long))
-				data[i] = *(unsigned long *)p;
+			if (s->stat_sizeof == sizeof(u64))
+				data[i] = *(u64 *)p;
 			else
 				data[i] = *(u32 *)p;
 		}
-- 
2.34.1

[PATCH net v2 2/5] net: bcmgenet: initialize u64 stats seq counter for all queues

[Florian Fainelli]

bcmgenet_gstrings_stats statically defines ethtool statistics for queues
0 through GENET_MAX_MQ_CNT (4). However, bcmgenet_probe() only initialized
the u64_stats_sync seq counter up to priv->hw_params->rx_queues and
priv->hw_params->tx_queues.

Since priv->hw_params->rx_queues is 0 across all hardware versions (and
priv->hw_params->tx_queues is 0 on GENET V1), rings 1..4 have uninitialized
u64_stats_sync structures. When ethtool -S is run on 32-bit kernels,
bcmgenet_get_ethtool_stats() reads stats from rx_rings[1..4], causing
lockdep warnings due to the uninitialized sequence counters.

Initialize the sequence counters for all GENET_MAX_MQ_CNT + 1 queues.

Fixes: ffc2c8c4a714 ("net: bcmgenet: Initialize u64 stats seq counter")
Assisted-by: LLM
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
---
 drivers/net/ethernet/broadcom/genet/bcmgenet.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index 7b089de9484e..055e1362173b 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -4134,10 +4134,10 @@ static int bcmgenet_probe(struct platform_device *pdev)
 		priv->rx_rings[i].rx_max_coalesced_frames = 1;
 
 	/* Initialize u64 stats seq counter for 32bit machines */
-	for (i = 0; i <= priv->hw_params->rx_queues; i++)
+	for (i = 0; i <= GENET_MAX_MQ_CNT; i++) {
 		u64_stats_init(&priv->rx_rings[i].stats64.syncp);
-	for (i = 0; i <= priv->hw_params->tx_queues; i++)
 		u64_stats_init(&priv->tx_rings[i].stats64.syncp);
+	}
 
 	/* libphy will determine the link state */
 	netif_carrier_off(dev);
-- 
2.34.1

[PATCH net v2 3/5] net: bcmgenet: do not skip WoL power up on GENET V1

[Florian Fainelli]

bcmgenet_power_up() had an early check for bcmgenet_has_ext(priv) before
dispatching by power mode. GENET V1 does not have the EXT block (unlike
GENET V2+), which causes bcmgenet_power_up() to immediately return 0.

As a consequence, when waking up from GENET_POWER_WOL_MAGIC on GENET V1,
bcmgenet_wol_power_up_cfg() is never invoked to disable the WoL clock,
clear wake event masks, and restore normal PHY and MAC operations.

Move the bcmgenet_has_ext() checks to the GENET_POWER_PASSIVE and
GENET_POWER_CABLE_SENSE cases where the EXT registers are actually
accessed, allowing GENET_POWER_WOL_MAGIC cleanup to execute on all
hardware versions.

Fixes: c3ae64ae0c08 ("net: bcmgenet: handle GENET_POWER_WOL_MAGIC")
Assisted-by: LLM
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Siged-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
---
 drivers/net/ethernet/broadcom/genet/bcmgenet.c | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index 055e1362173b..bfb74dca55d6 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -1762,13 +1762,12 @@ static int bcmgenet_power_up(struct bcmgenet_priv *priv,
 	int ret = 0;
 	u32 reg;
 
-	if (!bcmgenet_has_ext(priv))
-		return ret;
-
-	reg = bcmgenet_ext_readl(priv, EXT_EXT_PWR_MGMT);
-
 	switch (mode) {
 	case GENET_POWER_PASSIVE:
+		if (!bcmgenet_has_ext(priv))
+			break;
+
+		reg = bcmgenet_ext_readl(priv, EXT_EXT_PWR_MGMT);
 		reg &= ~(EXT_PWR_DOWN_DLL | EXT_PWR_DOWN_BIAS |
 			 EXT_ENERGY_DET_MASK);
 		if (GENET_IS_V5(priv) && !bcmgenet_has_ephy_16nm(priv)) {
@@ -1792,8 +1791,12 @@ static int bcmgenet_power_up(struct bcmgenet_priv *priv,
 		break;
 
 	case GENET_POWER_CABLE_SENSE:
+		if (!bcmgenet_has_ext(priv))
+			break;
+
 		/* enable APD */
 		if (!GENET_IS_V5(priv)) {
+			reg = bcmgenet_ext_readl(priv, EXT_EXT_PWR_MGMT);
 			reg |= EXT_PWR_DN_EN_LD;
 			bcmgenet_ext_writel(priv, reg, EXT_EXT_PWR_MGMT);
 		}
-- 
2.34.1

[PATCH net v2 4/5] net: bcmgenet: validate Ethernet address in bcmgenet_set_mac_addr

[Florian Fainelli]

bcmgenet_set_mac_addr() did not check whether the provided MAC address is a
valid Ethernet address before applying it. Userspace could configure an
invalid address (such as all zeroes or a multicast address) while the
interface is down.

Add a call to is_valid_ether_addr() and return -EADDRNOTAVAIL if the MAC
address is not valid.

Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Assisted-by: LLM
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
---
 drivers/net/ethernet/broadcom/genet/bcmgenet.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index bfb74dca55d6..e9d9d3d7b636 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -3634,6 +3634,9 @@ static int bcmgenet_set_mac_addr(struct net_device *dev, void *p)
 	if (netif_running(dev))
 		return -EBUSY;
 
+	if (!is_valid_ether_addr(addr->sa_data))
+		return -EADDRNOTAVAIL;
+
 	eth_hw_addr_set(dev, addr->sa_data);
 
 	return 0;
-- 
2.34.1

[PATCH net v2 5/5] net: bcmgenet: mask DMA_TIMEOUT_MASK when reading DMA_RING0_TIMEOUT

[Florian Fainelli]

bcmgenet_get_coalesce() reads DMA_RING0_TIMEOUT to calculate
rx_coalesce_usecs without masking out bits outside DMA_TIMEOUT_MASK
(16 bits). If upper bits are non-zero or contain status/flags, the
computed value of rx_coalesce_usecs returned to userspace via ethtool
becomes corrupted.

Mask the register read with DMA_TIMEOUT_MASK before computing the
timeout in microseconds.

Fixes: 4a29645bfe6c ("net: bcmgenet: Implement RX coalescing control knobs")
Assisted-by: LLM
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
---
 drivers/net/ethernet/broadcom/genet/bcmgenet.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index e9d9d3d7b636..ef3b750630d3 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -852,7 +852,8 @@ static int bcmgenet_get_coalesce(struct net_device *dev,
 	ec->rx_max_coalesced_frames =
 		bcmgenet_rdma_ring_readl(priv, 0, DMA_MBUF_DONE_THRESH);
 	ec->rx_coalesce_usecs =
-		bcmgenet_rdma_readl(priv, DMA_RING0_TIMEOUT) * 8192 / 1000;
+		(bcmgenet_rdma_readl(priv, DMA_RING0_TIMEOUT) &
+		 DMA_TIMEOUT_MASK) * 8192 / 1000;
 
 	for (i = 0; i <= priv->hw_params->rx_queues; i++) {
 		ring = &priv->rx_rings[i];
-- 
2.34.1