[PATCH net-next v2 0/6] net: ftgmac100: Add AST2700 support

[PATCH net-next v2 0/6] net: ftgmac100: Add AST2700 support

[Jacky Chou]

Add the pieces needed for the FTGMAC100 driver to run on Aspeed AST2700
systems.

AST2700 keeps using the FTGMAC100 MAC IP, but the enablement is not
limited to a new compatible string. The SoC can boot with the MAC on
ARM64, needs the Aspeed-specific RMII mode bit programmed when a port is
wired for RMII, and requires the driver to use the upper DMA address
fields in the ring base registers and packet descriptors. Those fields
expose a 35-bit DMA address range on AST2700, so the driver must request
a mask that matches the address bits the hardware can encode.

The series first documents and wires up the aspeed,ast2700-mac
compatible. It then treats AST2700 as an Aspeed MAC in the driver,
enables the RMII mode programming, writes the AST2700 high descriptor-ring
base registers, carries the RX/TX descriptor high address bits, rebuilds
full DMA addresses before unmapping buffers, and requests a 35-bit DMA
mask. The high ring base registers are only touched for AST2700 so older
Aspeed device tree register windows remain unchanged. With that in place,
the FTGMAC100 Kconfig entry can be made available on ARM64 while keeping
the existing Aspeed MDIO dependency for AST2600 and newer ARCH_ASPEED
systems.

RGMII delay is configured at the bootloader stage, the same way it is
handled for AST2600, not by this driver. Aspeed's SDK bootloader
configures both AST2600 and AST2700 boards with the RGMII delay
disabled and advertises "phy-mode = rgmii-id" to match, mirroring the
OpenBMC bootloader change that stopped inserting delays on AST2600 so
its device trees could use the correct "rgmii-id" setting. On AST2700,
every on-chip MAC is likewise configured by the bootloader with RGMII
delay disabled and "rgmii-id" phy-mode. Because the delay is already
resolved before Linux boots, the ftgmac100 driver does not need to
program any RGMII delay for either AST2600 or AST2700.

This series has been validated on AST2700 EVB and AST2600 EVB.

Patch layout:
- patch 1 updates the binding for the AST2700 compatible, RMII RCLK gate,
  and reset support.
- patch 2 adds the AST2700 match data and OF compatible.
- patch 3 programs the AST2700 RMII enable bit.
- patch 4 makes "phy-mode" a required device tree property for AST2700
  and fails probe if it is missing.
- patch 5 adds AST2700 upper DMA address handling for rings and
  descriptors.
- patch 6 enables the Faraday/FTGMAC100 Kconfig options on ARM64 and
  selects MDIO_ASPEED for ARCH_ASPEED.

Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
---
Changes in v2:
- Make "phy-mode" a required device tree property for AST2700 and fail
  probe if it is missing, instead of silently defaulting to RGMII.
- Document in the cover letter how RGMII delay is configured at the
  bootloader stage for AST2600 and AST2700.
- Simplify the MDIO_ASPEED Kconfig select to ARCH_ASPEED only, dropping
  the redundant MACH_ASPEED_G6 condition, and update its help text to
  mention AST2700.
- Pick up Reviewed-by from Krzysztof Kozlowski on the dt-bindings patch.
- Link to v1: https://lore.kernel.org/r/20260927-support_ast2700-v1-0-9f03f29d2c82@aspeedtech.com

---
Jacky Chou (6):
      dt-bindings: net: ftgmac100: Add AST2700 compatible
      net: ftgmac100: Add AST2700 compatible support
      net: ftgmac100: Enable AST2700 RMII support
      net: ftgmac100: Require phy-mode for AST2700
      net: ftgmac100: Add AST2700 upper DMA address support
      net: ftgmac100: Allow building on ARM64

 .../devicetree/bindings/net/faraday,ftgmac100.yaml |  4 +-
 drivers/net/ethernet/faraday/Kconfig               |  7 +-
 drivers/net/ethernet/faraday/ftgmac100.c           | 93 +++++++++++++++++++---
 drivers/net/ethernet/faraday/ftgmac100.h           |  7 ++
 drivers/net/mdio/Kconfig                           | 16 ++--
 5 files changed, 104 insertions(+), 23 deletions(-)
---
base-commit: a5e7d8e446af9803e37a3b6a4d416fb41178348f
change-id: 20260623-support_ast2700-68fb164da45c

Best regards,
-- 
Jacky Chou <jacky_chou@aspeedtech.com>

[PATCH net-next v2 1/6] dt-bindings: net: ftgmac100: Add AST2700 compatible

[Jacky Chou]

Add AST2700 to the FTGMAC100 compatible list and document that its
RMII RCLK gate matches the earlier Aspeed SoCs. Allow the reset line for
AST2700 as it follows the same reset requirements as AST2600.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
---
 Documentation/devicetree/bindings/net/faraday,ftgmac100.yaml | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/faraday,ftgmac100.yaml b/Documentation/devicetree/bindings/net/faraday,ftgmac100.yaml
index d14410018bcf..bee9570a6f63 100644
--- a/Documentation/devicetree/bindings/net/faraday,ftgmac100.yaml
+++ b/Documentation/devicetree/bindings/net/faraday,ftgmac100.yaml
@@ -18,6 +18,7 @@ properties:
               - aspeed,ast2400-mac
               - aspeed,ast2500-mac
               - aspeed,ast2600-mac
+              - aspeed,ast2700-mac
           - const: faraday,ftgmac100
 
   reg:
@@ -30,7 +31,7 @@ properties:
     minItems: 1
     items:
       - description: MAC IP clock
-      - description: RMII RCLK gate for AST2500/2600
+      - description: RMII RCLK gate for AST2500/2600/2700
 
   resets:
     maxItems: 1
@@ -82,6 +83,7 @@ allOf:
           contains:
             enum:
               - aspeed,ast2600-mac
+              - aspeed,ast2700-mac
     then:
       properties:
         resets: true

-- 
2.34.1

[PATCH net-next v2 2/6] net: ftgmac100: Add AST2700 compatible support

[Jacky Chou]

Add match data for the Aspeed AST2700 FTGMAC100 controller and wire
its compatible string into the OF match table. This lets AST2700 device
tree nodes bind to the ftgmac100 driver.

Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
---
 drivers/net/ethernet/faraday/ftgmac100.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 6d2fe5c2f390..67b1fa464a42 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -37,7 +37,8 @@ enum ftgmac100_mac_id {
 	FTGMAC100_FARADAY = 1,
 	FTGMAC100_AST2400,
 	FTGMAC100_AST2500,
-	FTGMAC100_AST2600
+	FTGMAC100_AST2600,
+	FTGMAC100_AST2700
 };
 
 struct ftgmac100_match_data {
@@ -2017,7 +2018,8 @@ static int ftgmac100_probe(struct platform_device *pdev)
 
 	if (priv->mac_id == FTGMAC100_AST2400 ||
 	    priv->mac_id == FTGMAC100_AST2500 ||
-	    priv->mac_id == FTGMAC100_AST2600) {
+	    priv->mac_id == FTGMAC100_AST2600 ||
+	    priv->mac_id == FTGMAC100_AST2700) {
 		priv->rxdes0_edorr_mask = BIT(30);
 		priv->txdes0_edotr_mask = BIT(30);
 		priv->is_aspeed = true;
@@ -2131,6 +2133,10 @@ static const struct ftgmac100_match_data ftgmac100_match_data_ast2600 = {
 	.mac_id = FTGMAC100_AST2600
 };
 
+static const struct ftgmac100_match_data ftgmac100_match_data_ast2700 = {
+	.mac_id = FTGMAC100_AST2700
+};
+
 static const struct ftgmac100_match_data ftgmac100_match_data_faraday = {
 	.mac_id = FTGMAC100_FARADAY
 };
@@ -2142,6 +2148,8 @@ static const struct of_device_id ftgmac100_of_match[] = {
 	  .data = &ftgmac100_match_data_ast2500 },
 	{ .compatible = "aspeed,ast2600-mac",
 	  .data = &ftgmac100_match_data_ast2600 },
+	{ .compatible = "aspeed,ast2700-mac",
+	  .data = &ftgmac100_match_data_ast2700 },
 	{ .compatible = "faraday,ftgmac100",
 	  .data = &ftgmac100_match_data_faraday },
 	{ }

-- 
2.34.1

[PATCH net-next v2 3/6] net: ftgmac100: Enable AST2700 RMII support

[Jacky Chou]

Set the RMII enable bit when an AST2700 port uses RMII so the MAC is
programmed for the selected interface mode. Describe the requirement as
a match-data quirk instead of checking the MAC generation in the data
path, allowing later compatible controllers to opt into the behavior.

Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
---
 drivers/net/ethernet/faraday/ftgmac100.c | 16 ++++++++++++++--
 drivers/net/ethernet/faraday/ftgmac100.h |  1 +
 2 files changed, 15 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 67b1fa464a42..b835472da360 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -41,8 +41,11 @@ enum ftgmac100_mac_id {
 	FTGMAC100_AST2700
 };
 
+#define FTGMAC100_QUIRK_RMII_ENABLE	BIT(0)
+
 struct ftgmac100_match_data {
 	enum ftgmac100_mac_id mac_id;
+	u32 quirks;
 };
 
 /* Arbitrary values, I am not sure the HW has limits */
@@ -79,6 +82,7 @@ struct ftgmac100 {
 	void __iomem *base;
 
 	enum ftgmac100_mac_id mac_id;
+	u32 quirks;
 
 	/* Rx ring */
 	unsigned int rx_q_entries;
@@ -355,6 +359,7 @@ static void ftgmac100_init_hw(struct ftgmac100 *priv)
 static void ftgmac100_start_hw(struct ftgmac100 *priv)
 {
 	u32 maccr = ioread32(priv->base + FTGMAC100_OFFSET_MACCR);
+	struct phy_device *phydev = priv->netdev->phydev;
 
 	/* Keep the original GMAC and FAST bits */
 	maccr &= (FTGMAC100_MACCR_FAST_MODE | FTGMAC100_MACCR_GIGA_MODE);
@@ -383,6 +388,11 @@ static void ftgmac100_start_hw(struct ftgmac100 *priv)
 	if (priv->netdev->features & NETIF_F_HW_VLAN_CTAG_RX)
 		maccr |= FTGMAC100_MACCR_RM_VLAN;
 
+	if ((priv->quirks & FTGMAC100_QUIRK_RMII_ENABLE) &&
+	    phydev->interface == PHY_INTERFACE_MODE_RMII) {
+		maccr |= FTGMAC100_MACCR_RMII_ENABLE;
+	}
+
 	/* Hit the HW */
 	iowrite32(maccr, priv->base + FTGMAC100_OFFSET_MACCR);
 }
@@ -1942,7 +1952,7 @@ static int ftgmac100_probe_dt(struct net_device *netdev,
 
 static int ftgmac100_probe(struct platform_device *pdev)
 {
-	const struct ftgmac100_match_data *match_data;
+	const struct ftgmac100_match_data *match_data = NULL;
 	enum ftgmac100_mac_id mac_id;
 	struct resource *res;
 	int irq;
@@ -1987,6 +1997,7 @@ static int ftgmac100_probe(struct platform_device *pdev)
 	priv->netdev = netdev;
 	priv->dev = &pdev->dev;
 	priv->mac_id = mac_id;
+	priv->quirks = match_data ? match_data->quirks : 0;
 	INIT_WORK(&priv->reset_task, ftgmac100_reset_task);
 
 	/* map io memory */
@@ -2134,7 +2145,8 @@ static const struct ftgmac100_match_data ftgmac100_match_data_ast2600 = {
 };
 
 static const struct ftgmac100_match_data ftgmac100_match_data_ast2700 = {
-	.mac_id = FTGMAC100_AST2700
+	.mac_id = FTGMAC100_AST2700,
+	.quirks = FTGMAC100_QUIRK_RMII_ENABLE,
 };
 
 static const struct ftgmac100_match_data ftgmac100_match_data_faraday = {
diff --git a/drivers/net/ethernet/faraday/ftgmac100.h b/drivers/net/ethernet/faraday/ftgmac100.h
index 4968f6f0bdbc..8c35c895b146 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.h
+++ b/drivers/net/ethernet/faraday/ftgmac100.h
@@ -167,6 +167,7 @@
 #define FTGMAC100_MACCR_RX_BROADPKT	(1 << 17)
 #define FTGMAC100_MACCR_DISCARD_CRCERR	(1 << 18)
 #define FTGMAC100_MACCR_FAST_MODE	(1 << 19)
+#define FTGMAC100_MACCR_RMII_ENABLE	BIT(20)
 #define FTGMAC100_MACCR_SW_RST		(1 << 31)
 
 /*

-- 
2.34.1

[PATCH net-next v2 4/6] net: ftgmac100: Require phy-mode for AST2700

[Jacky Chou]

The driver currently defaults to RGMII when the "phy-mode" property
is missing from the device tree. This default is no longer valid for
AST2700, which also supports RMII via FTGMAC100_QUIRK_RMII_ENABLE.

Make "phy-mode" a required property for AST2700 and fail probe with
an error message if it is not specified, instead of silently
defaulting to RGMII.

Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
---
 drivers/net/ethernet/faraday/ftgmac100.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index b835472da360..2d029d1262e6 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -1521,8 +1521,13 @@ static int ftgmac100_mii_probe(struct net_device *netdev)
 
 	/* Default to RGMII. It's a gigabit part after all */
 	err = of_get_phy_mode(np, &phy_intf);
-	if (err)
+	if (err) {
+		if (priv->mac_id == FTGMAC100_AST2700) {
+			dev_err(priv->dev, "phy-mode is required for this SoC\n");
+			return -EINVAL;
+		}
 		phy_intf = PHY_INTERFACE_MODE_RGMII;
+	}
 
 	/* Aspeed only supports these. I don't know about other IP
 	 * block vendors so I'm going to just let them through for

-- 
2.34.1

[PATCH net-next v2 5/6] net: ftgmac100: Add AST2700 upper DMA address support

[Jacky Chou]

Program the high RX and TX descriptor ring base registers and carry the
upper DMA address bits in RX and TX descriptors. Rebuild full buffer DMA
addresses in a 64-bit type before unmapping them so bits 34:32 are not
lost to 32-bit arithmetic.

The descriptor format provides three upper buffer address bits, so
request a 35-bit DMA mask instead of advertising an address range that
the hardware cannot encode. Gate all extended address handling with a
match-data quirk so older register layouts remain untouched and later
compatible controllers can opt into the same capability.

Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
---
 drivers/net/ethernet/faraday/ftgmac100.c | 62 +++++++++++++++++++++++++++-----
 drivers/net/ethernet/faraday/ftgmac100.h |  6 ++++
 2 files changed, 59 insertions(+), 9 deletions(-)

diff --git a/drivers/net/ethernet/faraday/ftgmac100.c b/drivers/net/ethernet/faraday/ftgmac100.c
index 2d029d1262e6..af2e272f32f2 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.c
+++ b/drivers/net/ethernet/faraday/ftgmac100.c
@@ -8,6 +8,7 @@
 
 #define pr_fmt(fmt)	KBUILD_MODNAME ": " fmt
 
+#include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/reset.h>
 #include <linux/dma-mapping.h>
@@ -42,6 +43,7 @@ enum ftgmac100_mac_id {
 };
 
 #define FTGMAC100_QUIRK_RMII_ENABLE	BIT(0)
+#define FTGMAC100_QUIRK_DMA_35BIT	BIT(1)
 
 struct ftgmac100_match_data {
 	enum ftgmac100_mac_id mac_id;
@@ -303,10 +305,16 @@ static void ftgmac100_init_hw(struct ftgmac100 *priv)
 	iowrite32(reg, priv->base + FTGMAC100_OFFSET_ISR);
 
 	/* Setup RX ring buffer base */
-	iowrite32(priv->rxdes_dma, priv->base + FTGMAC100_OFFSET_RXR_BADR);
+	iowrite32(lower_32_bits(priv->rxdes_dma), priv->base + FTGMAC100_OFFSET_RXR_BADR);
+	if (priv->quirks & FTGMAC100_QUIRK_DMA_35BIT)
+		iowrite32(upper_32_bits(priv->rxdes_dma),
+			  priv->base + FTGMAC100_OFFSET_RXR_BADDR_HIGH);
 
 	/* Setup TX ring buffer base */
-	iowrite32(priv->txdes_dma, priv->base + FTGMAC100_OFFSET_NPTXR_BADR);
+	iowrite32(lower_32_bits(priv->txdes_dma), priv->base + FTGMAC100_OFFSET_NPTXR_BADR);
+	if (priv->quirks & FTGMAC100_QUIRK_DMA_35BIT)
+		iowrite32(upper_32_bits(priv->txdes_dma),
+			  priv->base + FTGMAC100_OFFSET_TXR_BADDR_HIGH);
 
 	/* Configure RX buffer size */
 	iowrite32(FTGMAC100_RBSR_SIZE(RX_BUF_SIZE),
@@ -469,7 +477,10 @@ static int ftgmac100_alloc_rx_buf(struct ftgmac100 *priv, unsigned int entry,
 	priv->rx_skbs[entry] = skb;
 
 	/* Store DMA address into RX desc */
-	rxdes->rxdes3 = cpu_to_le32(map);
+	if (priv->quirks & FTGMAC100_QUIRK_DMA_35BIT)
+		rxdes->rxdes2 = cpu_to_le32(FIELD_PREP(FTGMAC100_RXDES2_RXBUF_BADR_HI,
+						       upper_32_bits(map)));
+	rxdes->rxdes3 = cpu_to_le32(lower_32_bits(map));
 
 	/* Ensure the above is ordered vs clearing the OWN bit */
 	dma_wmb();
@@ -596,6 +607,9 @@ static bool ftgmac100_rx_packet(struct ftgmac100 *priv, int *processed)
 
 	/* Tear down DMA mapping, do necessary cache management */
 	map = le32_to_cpu(rxdes->rxdes3);
+	if (priv->quirks & FTGMAC100_QUIRK_DMA_35BIT)
+		map |= (u64)FIELD_GET(FTGMAC100_RXDES2_RXBUF_BADR_HI,
+				     le32_to_cpu(rxdes->rxdes2)) << 32;
 
 #if defined(CONFIG_ARM) && !defined(CONFIG_ARM_DMA_USE_IOMMU)
 	/* When we don't have an iommu, we can save cycles by not
@@ -672,9 +686,14 @@ static void ftgmac100_free_tx_packet(struct ftgmac100 *priv,
 				     struct ftgmac100_txdes *txdes,
 				     u32 ctl_stat)
 {
-	dma_addr_t map = le32_to_cpu(txdes->txdes3);
+	dma_addr_t map;
 	size_t len;
 
+	map = le32_to_cpu(txdes->txdes3);
+	if (priv->quirks & FTGMAC100_QUIRK_DMA_35BIT)
+		map |= (u64)FIELD_GET(FTGMAC100_TXDES2_TXBUF_BADR_HI,
+				     le32_to_cpu(txdes->txdes2)) << 32;
+
 	if (ctl_stat & FTGMAC100_TXDES0_FTS) {
 		len = skb_headlen(skb);
 		dma_unmap_single(priv->dev, map, len, DMA_TO_DEVICE);
@@ -828,7 +847,10 @@ static netdev_tx_t ftgmac100_hard_start_xmit(struct sk_buff *skb,
 	f_ctl_stat |= FTGMAC100_TXDES0_FTS;
 	if (nfrags == 0)
 		f_ctl_stat |= FTGMAC100_TXDES0_LTS;
-	txdes->txdes3 = cpu_to_le32(map);
+	if (priv->quirks & FTGMAC100_QUIRK_DMA_35BIT)
+		txdes->txdes2 = cpu_to_le32(FIELD_PREP(FTGMAC100_TXDES2_TXBUF_BADR_HI,
+						       upper_32_bits(map)));
+	txdes->txdes3 = cpu_to_le32(lower_32_bits(map));
 	txdes->txdes1 = cpu_to_le32(csum_vlan);
 
 	/* Next descriptor */
@@ -856,7 +878,10 @@ static netdev_tx_t ftgmac100_hard_start_xmit(struct sk_buff *skb,
 			ctl_stat |= FTGMAC100_TXDES0_LTS;
 		txdes->txdes0 = cpu_to_le32(ctl_stat);
 		txdes->txdes1 = 0;
-		txdes->txdes3 = cpu_to_le32(map);
+		if (priv->quirks & FTGMAC100_QUIRK_DMA_35BIT)
+			txdes->txdes2 = cpu_to_le32(FIELD_PREP(FTGMAC100_TXDES2_TXBUF_BADR_HI,
+							       upper_32_bits(map)));
+		txdes->txdes3 = cpu_to_le32(lower_32_bits(map));
 
 		/* Next one */
 		pointer = ftgmac100_next_tx_pointer(priv, pointer);
@@ -931,7 +956,12 @@ static void ftgmac100_free_buffers(struct ftgmac100 *priv)
 	for (i = 0; i < priv->rx_q_entries; i++) {
 		struct ftgmac100_rxdes *rxdes = &priv->rxdes[i];
 		struct sk_buff *skb = priv->rx_skbs[i];
-		dma_addr_t map = le32_to_cpu(rxdes->rxdes3);
+		dma_addr_t map;
+
+		map = le32_to_cpu(rxdes->rxdes3);
+		if (priv->quirks & FTGMAC100_QUIRK_DMA_35BIT)
+			map |= (u64)FIELD_GET(FTGMAC100_RXDES2_RXBUF_BADR_HI,
+					     le32_to_cpu(rxdes->rxdes2)) << 32;
 
 		if (!skb)
 			continue;
@@ -1050,7 +1080,12 @@ static void ftgmac100_init_rings(struct ftgmac100 *priv)
 	for (i = 0; i < priv->rx_q_entries; i++) {
 		rxdes = &priv->rxdes[i];
 		rxdes->rxdes0 = 0;
-		rxdes->rxdes3 = cpu_to_le32(priv->rx_scratch_dma);
+		if (priv->quirks & FTGMAC100_QUIRK_DMA_35BIT) {
+			u32 hi = upper_32_bits(priv->rx_scratch_dma);
+
+			rxdes->rxdes2 = cpu_to_le32(FIELD_PREP(FTGMAC100_RXDES2_RXBUF_BADR_HI, hi));
+		}
+		rxdes->rxdes3 = cpu_to_le32(lower_32_bits(priv->rx_scratch_dma));
 	}
 	/* Mark the end of the ring */
 	rxdes->rxdes0 |= cpu_to_le32(priv->rxdes0_edorr_mask);
@@ -2099,6 +2134,14 @@ static int ftgmac100_probe(struct platform_device *pdev)
 		netdev->hw_features &= ~(NETIF_F_HW_CSUM | NETIF_F_RXCSUM);
 	netdev->features |= netdev->hw_features;
 
+	if (priv->quirks & FTGMAC100_QUIRK_DMA_35BIT) {
+		err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(35));
+		if (err) {
+			dev_err(&pdev->dev, "35-bit DMA enable failed\n");
+			goto err;
+		}
+	}
+
 	/* register network device */
 	err = register_netdev(netdev);
 	if (err) {
@@ -2151,7 +2194,8 @@ static const struct ftgmac100_match_data ftgmac100_match_data_ast2600 = {
 
 static const struct ftgmac100_match_data ftgmac100_match_data_ast2700 = {
 	.mac_id = FTGMAC100_AST2700,
-	.quirks = FTGMAC100_QUIRK_RMII_ENABLE,
+	.quirks = FTGMAC100_QUIRK_RMII_ENABLE |
+		  FTGMAC100_QUIRK_DMA_35BIT,
 };
 
 static const struct ftgmac100_match_data ftgmac100_match_data_faraday = {
diff --git a/drivers/net/ethernet/faraday/ftgmac100.h b/drivers/net/ethernet/faraday/ftgmac100.h
index 8c35c895b146..0c244b1c0a35 100644
--- a/drivers/net/ethernet/faraday/ftgmac100.h
+++ b/drivers/net/ethernet/faraday/ftgmac100.h
@@ -57,6 +57,9 @@
 #define FTGMAC100_OFFSET_RX_RUNT	0xc0
 #define FTGMAC100_OFFSET_RX_CRCER_FTL	0xc4
 #define FTGMAC100_OFFSET_RX_COL_LOST	0xc8
+/* reserved 0xcc - 0x178 */
+#define FTGMAC100_OFFSET_TXR_BADDR_HIGH	0x17c
+#define FTGMAC100_OFFSET_RXR_BADDR_HIGH	0x18c
 
 /*
  * Interrupt status register & interrupt enable register
@@ -226,6 +229,7 @@ struct ftgmac100_txdes {
 #define FTGMAC100_TXDES1_TX2FIC		(1 << 30)
 #define FTGMAC100_TXDES1_TXIC		(1 << 31)
 
+#define FTGMAC100_TXDES2_TXBUF_BADR_HI	GENMASK(18, 16)
 /*
  * Receive descriptor, aligned to 16 bytes
  */
@@ -272,4 +276,6 @@ struct ftgmac100_rxdes {
 #define FTGMAC100_RXDES1_UDP_CHKSUM_ERR	(1 << 26)
 #define FTGMAC100_RXDES1_IP_CHKSUM_ERR	(1 << 27)
 
+#define FTGMAC100_RXDES2_RXBUF_BADR_HI	GENMASK(18, 16)
+
 #endif /* __FTGMAC100_H */

-- 
2.34.1

[PATCH net-next v2 6/6] net: ftgmac100: Allow building on ARM64

[Jacky Chou]

Allow the Faraday vendor menu and FTGMAC100 driver to be selected on
ARM64 so AST2700 platforms can enable the MAC. The driver now programs
the upper DMA address fields, so it no longer needs to be marked BROKEN
for 64-bit builds.

AST2700 has no dedicated MACH_ASPEED_G7 symbol; unlike the 32-bit
generations it is only gated by the common ARCH_ASPEED symbol. On
32-bit Aspeed platforms, arch/arm/mach-aspeed/Kconfig nests
MACH_ASPEED_G4/G5/G6 under "if ARCH_ASPEED", so MACH_ASPEED_G6 already
implies ARCH_ASPEED and is redundant once ARCH_ASPEED is part of the
condition. Drop it and select MDIO_ASPEED directly on ARCH_ASPEED.

This does widen the MDIO_ASPEED select beyond AST2600: it is now also
selected for AST2400/AST2500, which keep driving their embedded MDIO
controller from FTGMAC100 itself and have no MDIO node for this driver
to bind to, so it is built but stays unused there. Update the
MDIO_ASPEED help text to describe this.

Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
---
 drivers/net/ethernet/faraday/Kconfig |  7 +++----
 drivers/net/mdio/Kconfig             | 16 ++++++++++------
 2 files changed, 13 insertions(+), 10 deletions(-)

diff --git a/drivers/net/ethernet/faraday/Kconfig b/drivers/net/ethernet/faraday/Kconfig
index 474073c7f94d..9acc2d260c1f 100644
--- a/drivers/net/ethernet/faraday/Kconfig
+++ b/drivers/net/ethernet/faraday/Kconfig
@@ -6,7 +6,7 @@
 config NET_VENDOR_FARADAY
 	bool "Faraday devices"
 	default y
-	depends on ARM || COMPILE_TEST
+	depends on ARM || ARM64 || COMPILE_TEST
 	help
 	  If you have a network (Ethernet) card belonging to this class, say Y.
 
@@ -28,11 +28,10 @@ config FTMAC100
 
 config FTGMAC100
 	tristate "Faraday FTGMAC100 Gigabit Ethernet support"
-	depends on ARM || COMPILE_TEST
-	depends on !64BIT || BROKEN
+	depends on ARM || ARM64 || COMPILE_TEST
 	select PHYLIB
 	select FIXED_PHY
-	select MDIO_ASPEED if MACH_ASPEED_G6
+	select MDIO_ASPEED if ARCH_ASPEED
 	select CRC32
 	help
 	  This driver supports the FTGMAC100 Gigabit Ethernet controller
diff --git a/drivers/net/mdio/Kconfig b/drivers/net/mdio/Kconfig
index d44278f26fab..d784782c230f 100644
--- a/drivers/net/mdio/Kconfig
+++ b/drivers/net/mdio/Kconfig
@@ -50,12 +50,16 @@ config MDIO_ASPEED
 	depends on OF_MDIO && HAS_IOMEM
 	help
 	  This module provides a driver for the independent MDIO bus
-	  controllers found in the ASPEED AST2600 SoC. This is a driver for the
-	  third revision of the ASPEED MDIO register interface - the first two
-	  revisions are the "old" and "new" interfaces found in the AST2400 and
-	  AST2500, embedded in the MAC. For legacy reasons, FTGMAC100 driver
-	  continues to drive the embedded MDIO controller for the AST2400 and
-	  AST2500 SoCs, so say N if AST2600 support is not required.
+	  controllers found in the ASPEED AST2600 and AST2700 SoCs. This is a
+	  driver for the third revision of the ASPEED MDIO register interface -
+	  the first two revisions are the "old" and "new" interfaces found in
+	  the AST2400 and AST2500, embedded in the MAC. For legacy reasons,
+	  FTGMAC100 driver continues to drive the embedded MDIO controller for
+	  the AST2400 and AST2500 SoCs. AST2700 has no dedicated MACH_ASPEED_G7
+	  symbol and is only gated by ARCH_ASPEED, so FTGMAC100 now
+	  unconditionally selects this driver on every ARCH_ASPEED platform,
+	  including the older AST2400/AST2500 SoCs where it has no MDIO node to
+	  bind to.
 
 config MDIO_BITBANG
 	tristate "Bitbanged MDIO buses"

-- 
2.34.1