[PATCH net v4] net: phy: marvell: keep WOL_EIE across interrupt reconfiguration

[PATCH net v4] net: phy: marvell: keep WOL_EIE across interrupt reconfiguration

[Rosen Penev]

marvell_config_intr() rewrote the whole interrupt enable register, so
the config_intr call from phy_init_hw() on resume silently cleared
WOL_EIE on the 88E1318S and 88E1510: m88e1318_get_wol() still reported
WAKE_MAGIC, but a matched magic packet was no longer routed to INTn and
the board did not wake.

Make config_intr update every bit except WOL_EIE with phy_modify(), so
the WoL interrupt enable is owned only by set_wol and always matches
what it programmed. The read-modify-write runs under the MDIO bus lock,
as do the accesses in m88e1318_set_wol(), so the two can no longer
overwrite each other's update. Have m88e1318_set_wol() clear WOL_EIE
when WoL is fully disabled, since config_intr no longer does.

The interrupt register layout is the same across the PHYs this driver
handles, so extend the shared handler to also claim a WoL event instead
of adding a per-PHY one.

Fixes: 3871c3876f80 ("mv643xx_eth with 88E1318S: support Wake on LAN")
Assisted-by: LLM
Signed-off-by: Rosen Penev <rosenp@gmail.com>
---
 v4: remove MII_88E1318S_PHY_CSIER_ defines.
 v3: use phy_modify()
 v2: resolved review warnings, including wol d.
 drivers/net/phy/marvell.c | 39 +++++++++++++++++++++++++++------------
 1 file changed, 27 insertions(+), 12 deletions(-)

diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c
index f71cffa88406..5f9a43a4a063 100644
--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -55,6 +55,12 @@
 #define MII_M1011_IMASK			0x12
 #define MII_M1011_IMASK_INIT		0x6400
 #define MII_M1011_IMASK_CLEAR		0x0000
+#define MII_M1011_IMASK_WOL		BIT(7)
+/* Bits updated by config_intr. The WoL interrupt enable is owned by
+ * set_wol, so the config_intr call from phy_init_hw() on resume does not
+ * silently disarm Wake-on-LAN.
+ */
+#define MII_M1011_IMASK_CONFIG_MASK	(U16_MAX & ~MII_M1011_IMASK_WOL)
 
 #define MII_M1011_PHY_SCR			0x10
 #define MII_M1011_PHY_SCR_DOWNSHIFT_EN		BIT(11)
@@ -139,11 +145,6 @@
 #define MII_88E1318S_PHY_MSCR1_REG	16
 #define MII_88E1318S_PHY_MSCR1_PAD_ODD	BIT(6)
 
-/* Copper Specific Interrupt Enable Register */
-#define MII_88E1318S_PHY_CSIER				0x12
-/* WOL Event Interrupt Enable */
-#define MII_88E1318S_PHY_CSIER_WOL_EIE			BIT(7)
-
 #define MII_88E1318S_PHY_LED_FUNC		0x10
 #define MII_88E1318S_PHY_LED_FUNC_OFF		(0x8)
 #define MII_88E1318S_PHY_LED_FUNC_ON		(0x9)
@@ -393,11 +394,13 @@ static int marvell_config_intr(struct phy_device *phydev)
 		if (err)
 			return err;
 
-		err = phy_write(phydev, MII_M1011_IMASK,
-				MII_M1011_IMASK_INIT);
+		err = phy_modify(phydev, MII_M1011_IMASK,
+				 MII_M1011_IMASK_CONFIG_MASK,
+				 MII_M1011_IMASK_INIT);
 	} else {
-		err = phy_write(phydev, MII_M1011_IMASK,
-				MII_M1011_IMASK_CLEAR);
+		err = phy_modify(phydev, MII_M1011_IMASK,
+				 MII_M1011_IMASK_CONFIG_MASK,
+				 MII_M1011_IMASK_CLEAR);
 		if (err)
 			return err;
 
@@ -417,7 +420,7 @@ static irqreturn_t marvell_handle_interrupt(struct phy_device *phydev)
 		return IRQ_NONE;
 	}
 
-	if (!(irq_status & MII_M1011_IMASK_INIT))
+	if (!(irq_status & (MII_M1011_IMASK_INIT | MII_M1011_IMASK_WOL)))
 		return IRQ_NONE;
 
 	phy_trigger_machine(phydev);
@@ -1991,8 +1994,8 @@ static int m88e1318_set_wol(struct phy_device *phydev,
 			__phy_read(phydev, MII_M1011_IEVENT);
 
 		/* Enable the WOL interrupt */
-		err = __phy_set_bits(phydev, MII_88E1318S_PHY_CSIER,
-				     MII_88E1318S_PHY_CSIER_WOL_EIE);
+		err = __phy_set_bits(phydev, MII_M1011_IMASK,
+				     MII_M1011_IMASK_WOL);
 		if (err < 0)
 			goto error;
 
@@ -2074,6 +2077,18 @@ static int m88e1318_set_wol(struct phy_device *phydev,
 			goto error;
 	}
 
+	if (!(wol->wolopts & (WAKE_MAGIC | WAKE_PHY))) {
+		err = marvell_write_page(phydev, MII_MARVELL_COPPER_PAGE);
+		if (err < 0)
+			goto error;
+
+		/* Disable the WOL interrupt, config_intr leaves it alone */
+		err = __phy_clear_bits(phydev, MII_M1011_IMASK,
+				       MII_M1011_IMASK_WOL);
+		if (err < 0)
+			goto error;
+	}
+
 error:
 	return phy_restore_page(phydev, oldpage, err);
 }
-- 
2.56.0

Re: [PATCH net v4] net: phy: marvell: keep WOL_EIE across interrupt reconfiguration

[netdev-bot+sinfo]

Hi!

This is an automated message. This series looks like a fix, but its
commit messages seem to be missing some information:

 - How the issue was discovered, e.g. hit in production, hit during
   development, syzbot report, manual code inspection, LLM or static
   analysis tool scan.

Please do not repost the series just to address the above. Instead,
reply to this email with the missing information, so that reviewers
can take it into account. If the series needs another revision for
other reasons, please include the information in the commit messages
then.

The evaluation is done by an LLM so it may be wrong, if you think
that is the case please reply and explain.

Re: [PATCH net v4] net: phy: marvell: keep WOL_EIE across interrupt reconfiguration

[Rosen Penev]

On Wed, Oct 7, 2026 at 11:24 AM <netdev-bot+sinfo@kernel.org> wrote:
>
> Hi!
>
> This is an automated message. This series looks like a fix, but its
> commit messages seem to be missing some information:
>
>  - How the issue was discovered, e.g. hit in production, hit during
>    development, syzbot report, manual code inspection, LLM or static
>    analysis tool scan.
Tested on Helios 4.
>
> Please do not repost the series just to address the above. Instead,
> reply to this email with the missing information, so that reviewers
> can take it into account. If the series needs another revision for
> other reasons, please include the information in the commit messages
> then.
>
> The evaluation is done by an LLM so it may be wrong, if you think
> that is the case please reply and explain.