[PATCH v2 0/3] Bluetooth: btmtk: fix ISO data reception

[PATCH v2 0/3] Bluetooth: btmtk: fix ISO data reception

[Chris Lu]

Three fixes for ISO data handling in btmtk, found while debugging LE Audio
on MT7925. The code is shared by every MediaTek USB controller that
supports ISO data, so none of this is specific to that part.

Patch 1 drops the zero padding that the ISO interrupt IN endpoint appends
to each transfer instead of parsing it as ISO packets. The driver turns
that padding into handle 0 packets with a Data_Total_Length of zero and
hands them to the stack, which is what fills the HCI log with malformed
ISO frames, and a valid SDU is lost whenever handle 0 belongs to a live
CIS/BIS.

Patch 2 bounds Data_Total_Length by hdev->iso_mtu. The existing
skb_tailroom() test enforces no protocol limit, because the skb head
allocation is rounded up to a kmalloc bucket and skb_tailroom() reports
the bucket size rather than what was requested.

Patch 3 updates the mt79xx ISO data transmission setting.

The three hunks do not overlap, so any prefix of the series applies on its
own.

Changes in v2:
- Patch 2 reworked and retitled. v1 only enlarged the receive skb, which
  turned out to be a no-op, and added no bound at all. v2 bounds
  Data_Total_Length by hdev->iso_mtu and sizes the skb from the same
  value.
- Patch 3 added.
- Patch 1 unchanged.

Based on bluetooth-next.

Chris Lu (3):
  Bluetooth: btmtk: drop zero-length ISO packets from endpoint padding
  Bluetooth: btmtk: bound the ISO payload length by the controller's MTU
  Bluetooth: btmtk: derive the firmware ISO setting from
    MTK_ISO_THRESHOLD

 drivers/bluetooth/btmtk.c | 37 ++++++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)

-- 
2.45.2

[PATCH v2 1/3] Bluetooth: btmtk: drop zero-length ISO packets from endpoint padding

[Chris Lu]

The ISO interrupt IN endpoint delivers a fixed-size transfer that holds
one HCI ISO packet and zero-fills the remainder. That padding belongs to
the transfer rather than to the stream, so it has to be dropped instead of
reported to the host.

btmtk_recv_isopkt() keeps parsing it: the zero bytes read as an ISO header
with handle 0 and a Data_Total_Length of zero, and each one is passed to
hci_recv_frame() as a complete frame. A single transfer yields a long run
of them, which is what fills the HCI log with malformed ISO packets, and
iso_recv() drops the SDU it is reassembling whenever handle 0 belongs to a
live CIS/BIS.

A zero Data_Total_Length carries no ISO Data Load, so such a packet is
never part of the stream. The padding runs to the end of the transfer, so
stop parsing once one is seen.

This was observed on MT7925, but btmtk_recv_isopkt() is shared by every
MediaTek USB controller that supports ISO data.

Fixes: ceac1cb0259d ("Bluetooth: btusb: mediatek: add ISO data transmission functions")
Co-developed-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Co-developed-by: Wenlong Tian <ot_wenlong.tian@mediatek.com>
Signed-off-by: Wenlong Tian <ot_wenlong.tian@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
---
 drivers/bluetooth/btmtk.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/drivers/bluetooth/btmtk.c b/drivers/bluetooth/btmtk.c
index bdc85147b97f..869eb2176379 100644
--- a/drivers/bluetooth/btmtk.c
+++ b/drivers/bluetooth/btmtk.c
@@ -1201,6 +1201,19 @@ static int btmtk_recv_isopkt(struct hci_dev *hdev, void *buffer, int count)
 			/* Complete ISO header */
 			hci_skb_expect(skb) = __le16_to_cpu(dlen);
 
+			/* The interrupt endpoint zero-fills the remainder of
+			 * each transfer, and that padding parses as a header
+			 * with a zero Data_Total_Length. Such a packet carries
+			 * no ISO Data Load at all and is never emitted by the
+			 * controller, so stop parsing here rather than hand a
+			 * bogus handle 0 packet to the stack.
+			 */
+			if (!hci_skb_expect(skb)) {
+				kfree_skb(skb);
+				skb = NULL;
+				break;
+			}
+
 			if (skb_tailroom(skb) < hci_skb_expect(skb)) {
 				kfree_skb(skb);
 				skb = NULL;
-- 
2.45.2

[PATCH v2 2/3] Bluetooth: btmtk: bound the ISO payload length by the controller's MTU

[Chris Lu]

btmtk_recv_isopkt() bounds the Data_Total_Length reported by the
controller with skb_tailroom(skb) < hci_skb_expect(skb). That keeps the
reassembly inside the skb, but it enforces no protocol limit: the head
allocation is rounded up to the next kmalloc bucket and skb_tailroom()
reports what the bucket can hold rather than what was requested, which is
several hundred bytes more. An oversized length therefore passes, and the
parser keeps pulling bytes out of the following transfers to fill it,
swallowing the real ISO packets they carry until the frame is handed to
hci_recv_frame().

The controller reports the largest ISO_Data_Packet_Length it will send in
LE Read Buffer Size [v2], which hci_cc_le_read_buffer_size_v2() keeps in
hdev->iso_mtu. Once that is available, bound the length by it and size the
receive skb to hold that much plus the 4-byte header. HCI_MAX_ISO_SIZE is
kept only as a fallback for the window before the command completes.

Keep the skb_tailroom() test as well, because a fragment started before
hdev->iso_mtu was populated sits in an skb sized for the fallback.

Fixes: ceac1cb0259d ("Bluetooth: btusb: mediatek: add ISO data transmission functions")
Co-developed-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Co-developed-by: Wenlong Tian <ot_wenlong.tian@mediatek.com>
Signed-off-by: Wenlong Tian <ot_wenlong.tian@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
---
 drivers/bluetooth/btmtk.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)

diff --git a/drivers/bluetooth/btmtk.c b/drivers/bluetooth/btmtk.c
index 869eb2176379..7c3fffcefdf1 100644
--- a/drivers/bluetooth/btmtk.c
+++ b/drivers/bluetooth/btmtk.c
@@ -1169,8 +1169,15 @@ static int btmtk_recv_isopkt(struct hci_dev *hdev, void *buffer, int count)
 	struct btmtk_data *btmtk_data = hci_get_priv(hdev);
 	struct sk_buff *skb;
 	unsigned long flags;
+	unsigned int iso_mtu;
 	int err = 0;
 
+	/* The controller reports the largest Data_Total_Length it will send in
+	 * LE Read Buffer Size [v2]. Fall back to HCI_MAX_ISO_SIZE while that
+	 * command has not completed yet.
+	 */
+	iso_mtu = hdev->iso_mtu ? hdev->iso_mtu : HCI_MAX_ISO_SIZE;
+
 	spin_lock_irqsave(&btmtk_data->isorxlock, flags);
 	skb = btmtk_data->isopkt_skb;
 
@@ -1178,7 +1185,8 @@ static int btmtk_recv_isopkt(struct hci_dev *hdev, void *buffer, int count)
 		int len;
 
 		if (!skb) {
-			skb = bt_skb_alloc(HCI_MAX_ISO_SIZE, GFP_ATOMIC);
+			skb = bt_skb_alloc(HCI_ISO_HDR_SIZE + iso_mtu,
+					   GFP_ATOMIC);
 			if (!skb) {
 				err = -ENOMEM;
 				break;
@@ -1214,7 +1222,13 @@ static int btmtk_recv_isopkt(struct hci_dev *hdev, void *buffer, int count)
 				break;
 			}
 
-			if (skb_tailroom(skb) < hci_skb_expect(skb)) {
+			/* Reject a length the controller said it would never
+			 * send. The skb_tailroom() test is kept because a
+			 * fragment started before hdev->iso_mtu was populated
+			 * sits in a smaller skb than iso_mtu now allows.
+			 */
+			if (hci_skb_expect(skb) > iso_mtu ||
+			    skb_tailroom(skb) < hci_skb_expect(skb)) {
 				kfree_skb(skb);
 				skb = NULL;
 
-- 
2.45.2

[PATCH v2 3/3] Bluetooth: btmtk: derive the firmware ISO setting from MTK_ISO_THRESHOLD

[Chris Lu]

The ISO data transfer size is spelled out twice: as a raw byte pair in the
vendor command sent by btmtk_usb_isointf_init(), and as MTK_ISO_THRESHOLD
for the padding in btmtk_isopkt_pad(). Build the command payload from the
macro so the size is stated once, and update the setting for current
MediaTek controllers.

Fixes: ceac1cb0259d ("Bluetooth: btusb: mediatek: add ISO data transmission functions")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
---
 drivers/bluetooth/btmtk.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/bluetooth/btmtk.c b/drivers/bluetooth/btmtk.c
index 7c3fffcefdf1..9424125ce539 100644
--- a/drivers/bluetooth/btmtk.c
+++ b/drivers/bluetooth/btmtk.c
@@ -24,7 +24,7 @@
 #define MTK_SEC_MAP_NEED_SEND_SIZE	52
 
 /* It is for mt79xx iso data transmission setting */
-#define MTK_ISO_THRESHOLD	264
+#define MTK_ISO_THRESHOLD	342
 
 struct btmtk_patch_header {
 	u8 datetime[16];
@@ -1347,7 +1347,7 @@ static int btmtk_submit_intr_urb(struct hci_dev *hdev, gfp_t mem_flags)
 static int btmtk_usb_isointf_init(struct hci_dev *hdev)
 {
 	struct btmtk_data *btmtk_data = hci_get_priv(hdev);
-	u8 iso_param[2] = { 0x08, 0x01 };
+	__le16 iso_param = cpu_to_le16(MTK_ISO_THRESHOLD);
 	struct sk_buff *skb;
 	int err;
 
@@ -1362,7 +1362,7 @@ static int btmtk_usb_isointf_init(struct hci_dev *hdev)
 		return err;
 	}
 
-	skb = __hci_cmd_sync(hdev, 0xfd98, sizeof(iso_param), iso_param,
+	skb = __hci_cmd_sync(hdev, 0xfd98, sizeof(iso_param), &iso_param,
 			     HCI_INIT_TIMEOUT);
 	if (IS_ERR(skb)) {
 		bt_dev_err(hdev, "Failed to apply iso setting (%ld)", PTR_ERR(skb));
-- 
2.45.2

Re: [PATCH v2 0/3] Bluetooth: btmtk: fix ISO data reception

[Luiz Augusto von Dentz]

Hi Chris,

On Thu, Oct 15, 2026 at 4:15 AM Chris Lu <chris.lu@mediatek.com> wrote:
>
> Three fixes for ISO data handling in btmtk, found while debugging LE Audio
> on MT7925. The code is shared by every MediaTek USB controller that
> supports ISO data, so none of this is specific to that part.
>
> Patch 1 drops the zero padding that the ISO interrupt IN endpoint appends
> to each transfer instead of parsing it as ISO packets. The driver turns
> that padding into handle 0 packets with a Data_Total_Length of zero and
> hands them to the stack, which is what fills the HCI log with malformed
> ISO frames, and a valid SDU is lost whenever handle 0 belongs to a live
> CIS/BIS.
>
> Patch 2 bounds Data_Total_Length by hdev->iso_mtu. The existing
> skb_tailroom() test enforces no protocol limit, because the skb head
> allocation is rounded up to a kmalloc bucket and skb_tailroom() reports
> the bucket size rather than what was requested.
>
> Patch 3 updates the mt79xx ISO data transmission setting.
>
> The three hunks do not overlap, so any prefix of the series applies on its
> own.
>
> Changes in v2:
> - Patch 2 reworked and retitled. v1 only enlarged the receive skb, which
>   turned out to be a no-op, and added no bound at all. v2 bounds
>   Data_Total_Length by hdev->iso_mtu and sizes the skb from the same
>   value.
> - Patch 3 added.
> - Patch 1 unchanged.
>
> Based on bluetooth-next.
>
> Chris Lu (3):
>   Bluetooth: btmtk: drop zero-length ISO packets from endpoint padding
>   Bluetooth: btmtk: bound the ISO payload length by the controller's MTU
>   Bluetooth: btmtk: derive the firmware ISO setting from
>     MTK_ISO_THRESHOLD
>
>  drivers/bluetooth/btmtk.c | 37 ++++++++++++++++++++++++++++++++-----
>  1 file changed, 32 insertions(+), 5 deletions(-)
>
> --
> 2.45.2
>

In case you haven't seen it sashiko flagged a problem with this set:

https://sashiko.dev/#/patchset/20261015081450.1241194-1-chris.lu%40mediatek.com

Unsuccessful packets shall still be delivered to the host, this is
used, for example, to implement Packet Loss Concealment (PLC) logic.

-- 
Luiz Augusto von Dentz