[PATCH] arm64: dts: qcom: shikra-iqs: add M.2 Wi-Fi and Bluetooth overlay

[PATCH] arm64: dts: qcom: shikra-iqs: add M.2 Wi-Fi and Bluetooth overlay

[Linghui Wu]

Add an overlay for M.2 Key-E Wi-Fi and Bluetooth modules on Qualcomm
Shikra IQS EVK.

Describe the PCIe and UART connections through the M.2 connector, the
3.3 V supply, the W_DISABLE signals and the PCIe reset signal. Disable
the onboard Wi-Fi and Bluetooth nodes when the overlay is selected.

The Wi-Fi PCIe path was tested on a Shikra IQS EVK with a QCC2072
module. The overlay was applied, the link trained at Gen2 x1 and the
endpoint enumerated. Bluetooth UART and HCI runtime validation is
pending.

Co-developed-by: Wei Deng <wei.deng@oss.qualcomm.com>
Signed-off-by: Wei Deng <wei.deng@oss.qualcomm.com>
Signed-off-by: Linghui Wu <linghui.wu@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso   | 107 ++++++++++++++++++
 2 files changed, 108 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1c86e7e98f55..799faa32e2d9 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -339,6 +339,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdx75-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-m2-wifi-bt.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
diff --git a/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
new file mode 100644
index 000000000000..3264c0add67b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2026 Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	m2_keye_3p3: regulator-m2-keye-3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VREG_3P3_KEYE";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&qps_gpio_expander 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+		startup-delay-us = <100000>;
+	};
+
+	wifi-bt-connector {
+		compatible = "pcie-m2-e-connector";
+		vpcie3v3-supply = <&m2_keye_3p3>;
+		w-disable1-gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+		w-disable2-gpios = <&tlmm 60 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				m2_e_pcie_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&pcie_port0_ep>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				m2_e_uart_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&uart8_ep>;
+				};
+			};
+		};
+	};
+};
+
+&{/wcn3988-pmu} {
+	status = "disabled";
+};
+
+&i2c3 {
+	qps_gpio_expander: gpio@3c {
+		compatible = "nxp,pca9534";
+		reg = <0x3c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&pcie {
+	iommu-map = <0x0 &apps_smmu 0x0800 0x0 0x1>,
+		    <0x100 &apps_smmu 0x0801 0x0 0x1>;
+	vddpe-3v3-supply = <&m2_keye_3p3>;
+};
+
+&pcie_port0 {
+	compatible = "pciclass,0604";
+	reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>;
+
+	port {
+		pcie_port0_ep: endpoint {
+			remote-endpoint = <&m2_e_pcie_ep>;
+		};
+	};
+};
+
+&tc9563 {
+	reg = <0x1ff00 0x0 0x0 0x0 0x0>;
+	status = "disabled";
+};
+
+&uart8 {
+	bluetooth {
+		status = "disabled";
+	};
+
+	port {
+		uart8_ep: endpoint {
+			remote-endpoint = <&m2_e_uart_ep>;
+		};
+	};
+};
+
+&wifi {
+	status = "disabled";
+};
-- 
2.43.0

[PATCH v2] arm64: dts: qcom: shikra-iqs: add M.2 Wi-Fi and Bluetooth overlay

[Linghui Wu]

Add an overlay for M.2 Key-E Wi-Fi and Bluetooth modules on Qualcomm
Shikra IQS EVK.

Describe the PCIe and UART connections through the M.2 connector, the
3.3 V supply, the W_DISABLE signals and the PCIe reset signal. Disable
the onboard Wi-Fi and Bluetooth nodes when the overlay is selected.

The Wi-Fi PCIe path was tested on a Shikra IQS EVK with a QCC2072
module. The overlay was applied, the link trained at Gen2 x1 and the
endpoint enumerated. Bluetooth UART and HCI runtime validation is
pending.

Co-developed-by: Wei Deng <wei.deng@oss.qualcomm.com>
Signed-off-by: Wei Deng <wei.deng@oss.qualcomm.com>
Signed-off-by: Linghui Wu <linghui.wu@oss.qualcomm.com>
---
Changes in v2:
- Drop regulator-boot-on and startup-delay-us from the 3.3 V regulator.

 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso   | 106 ++++++++++++++++++
 2 files changed, 107 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1c86e7e98f55..799faa32e2d9 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -339,6 +339,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdx75-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-m2-wifi-bt.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
diff --git a/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
new file mode 100644
index 000000000000..9496c6558eef
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2026 Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	m2_keye_3p3: regulator-m2-keye-3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VREG_3P3_KEYE";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&qps_gpio_expander 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	wifi-bt-connector {
+		compatible = "pcie-m2-e-connector";
+
+		vpcie3v3-supply = <&m2_keye_3p3>;
+		w-disable1-gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+		w-disable2-gpios = <&tlmm 60 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				m2_e_pcie_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&pcie_port0_ep>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				m2_e_uart_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&uart8_ep>;
+				};
+			};
+		};
+	};
+};
+
+&{/wcn3988-pmu} {
+	status = "disabled";
+};
+
+&i2c3 {
+	qps_gpio_expander: gpio@3c {
+		compatible = "nxp,pca9534";
+		reg = <0x3c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&pcie {
+	iommu-map = <0x0 &apps_smmu 0x0800 0x0 0x1>,
+		    <0x100 &apps_smmu 0x0801 0x0 0x1>;
+	vddpe-3v3-supply = <&m2_keye_3p3>;
+};
+
+&pcie_port0 {
+	compatible = "pciclass,0604";
+	reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>;
+
+	port {
+		pcie_port0_ep: endpoint {
+			remote-endpoint = <&m2_e_pcie_ep>;
+		};
+	};
+};
+
+&tc9563 {
+	reg = <0x1ff00 0x0 0x0 0x0 0x0>;
+	status = "disabled";
+};
+
+&uart8 {
+	bluetooth {
+		status = "disabled";
+	};
+
+	port {
+		uart8_ep: endpoint {
+			remote-endpoint = <&m2_e_uart_ep>;
+		};
+	};
+};
+
+&wifi {
+	status = "disabled";
+};
-- 
2.43.0

Re: [PATCH v2] arm64: dts: qcom: shikra-iqs: add M.2 Wi-Fi and Bluetooth overlay

[Konrad Dybcio]

On 10/13/26 6:55 AM, Linghui Wu wrote:
> Add an overlay for M.2 Key-E Wi-Fi and Bluetooth modules on Qualcomm
> Shikra IQS EVK.
> 
> Describe the PCIe and UART connections through the M.2 connector, the
> 3.3 V supply, the W_DISABLE signals and the PCIe reset signal. Disable
> the onboard Wi-Fi and Bluetooth nodes when the overlay is selected.

Is this not part of the base board?

Why would I be prevented from using both the onboard and M.2 WLAN?

Konrad

[PATCH v3] arm64: dts: qcom: shikra-iqs: add M.2 Wi-Fi and Bluetooth overlay

[Linghui Wu]

Add an overlay for M.2 Key-E Wi-Fi and Bluetooth modules on the Qualcomm
Shikra IQS EVK.

The M.2 variant uses the external module connected through the Key-E
connector instead of the onboard WCN3988 devices. Disable the onboard
Wi-Fi and Bluetooth nodes when the overlay is selected so the device tree
matches the hardware variant and does not probe the unavailable onboard
connectivity path.

Describe the PCIe and UART connections through the M.2 connector, the
3.3 V supply, the W_DISABLE signals and the PCIe reset signal.

The Wi-Fi PCIe path was tested on a Shikra IQS EVK with a QCC2072
module. The overlay was applied, the link trained at Gen2 x1 and the
endpoint enumerated. Bluetooth UART and HCI runtime validation is
pending.

Co-developed-by: Wei Deng <wei.deng@oss.qualcomm.com>
Signed-off-by: Wei Deng <wei.deng@oss.qualcomm.com>
Signed-off-by: Linghui Wu <linghui.wu@oss.qualcomm.com>
---
Changes in v2:
- Drop regulator-boot-on and startup-delay-us from the 3.3 V regulator.

Changes in v3:
- Drop the unused reg override from the disabled TC9563 node.

 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso   | 105 +++++++++++++++++
 2 files changed, 106 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1c86e7e98f55..799faa32e2d9 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -339,6 +339,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdx75-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-m2-wifi-bt.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
diff --git a/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
new file mode 100644
index 000000000000..9496c6558eef
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2026 Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	m2_keye_3p3: regulator-m2-keye-3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VREG_3P3_KEYE";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&qps_gpio_expander 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	wifi-bt-connector {
+		compatible = "pcie-m2-e-connector";
+
+		vpcie3v3-supply = <&m2_keye_3p3>;
+		w-disable1-gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+		w-disable2-gpios = <&tlmm 60 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				m2_e_pcie_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&pcie_port0_ep>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				m2_e_uart_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&uart8_ep>;
+				};
+			};
+		};
+	};
+};
+
+&{/wcn3988-pmu} {
+	status = "disabled";
+};
+
+&i2c3 {
+	qps_gpio_expander: gpio@3c {
+		compatible = "nxp,pca9534";
+		reg = <0x3c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&pcie {
+	iommu-map = <0x0 &apps_smmu 0x0800 0x0 0x1>,
+		    <0x100 &apps_smmu 0x0801 0x0 0x1>;
+	vddpe-3v3-supply = <&m2_keye_3p3>;
+};
+
+&pcie_port0 {
+	compatible = "pciclass,0604";
+	reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>;
+
+	port {
+		pcie_port0_ep: endpoint {
+			remote-endpoint = <&m2_e_pcie_ep>;
+		};
+	};
+};
+
+&tc9563 {
+	status = "disabled";
+};
+
+&uart8 {
+	bluetooth {
+		status = "disabled";
+	};
+
+	port {
+		uart8_ep: endpoint {
+			remote-endpoint = <&m2_e_uart_ep>;
+		};
+	};
+};
+
+&wifi {
+	status = "disabled";
+};
-- 
2.43.0

Re: [PATCH v3] arm64: dts: qcom: shikra-iqs: add M.2 Wi-Fi and Bluetooth overlay

[Rob Herring]

On Mon, Oct 19, 2026 at 9:09 PM Linghui Wu <linghui.wu@oss.qualcomm.com> wrote:
>
> Add an overlay for M.2 Key-E Wi-Fi and Bluetooth modules on the Qualcomm
> Shikra IQS EVK.
>
> The M.2 variant uses the external module connected through the Key-E
> connector instead of the onboard WCN3988 devices. Disable the onboard
> Wi-Fi and Bluetooth nodes when the overlay is selected so the device tree
> matches the hardware variant and does not probe the unavailable onboard
> connectivity path.
>
> Describe the PCIe and UART connections through the M.2 connector, the
> 3.3 V supply, the W_DISABLE signals and the PCIe reset signal.
>
> The Wi-Fi PCIe path was tested on a Shikra IQS EVK with a QCC2072
> module. The overlay was applied, the link trained at Gen2 x1 and the
> endpoint enumerated. Bluetooth UART and HCI runtime validation is
> pending.
>
> Co-developed-by: Wei Deng <wei.deng@oss.qualcomm.com>
> Signed-off-by: Wei Deng <wei.deng@oss.qualcomm.com>
> Signed-off-by: Linghui Wu <linghui.wu@oss.qualcomm.com>
> ---
> Changes in v2:
> - Drop regulator-boot-on and startup-delay-us from the 3.3 V regulator.
>
> Changes in v3:
> - Drop the unused reg override from the disabled TC9563 node.
>
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso   | 105 +++++++++++++++++
>  2 files changed, 106 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 1c86e7e98f55..799faa32e2d9 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -339,6 +339,7 @@ dtb-$(CONFIG_ARCH_QCOM)     += sdx75-idp.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += shikra-cqm-evk.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += shikra-cqs-evk.dtb
>  dtb-$(CONFIG_ARCH_QCOM)        += shikra-iqs-evk.dtb
> +dtb-$(CONFIG_ARCH_QCOM)        += shikra-iqs-evk-m2-wifi-bt.dtbo

Overlays must be applied to a base DT to test that they apply. Sashiko
has pointed out that this doesn't apply on every version you've sent
and you've not replied to the report. Please reply on the other
issues.

Rob

Re: [PATCH v3] arm64: dts: qcom: shikra-iqs: add M.2 Wi-Fi and Bluetooth overlay

[Dmitry Baryshkov]

On Tue, Oct 20, 2026 at 10:09:25AM +0800, Linghui Wu wrote:
> Add an overlay for M.2 Key-E Wi-Fi and Bluetooth modules on the Qualcomm
> Shikra IQS EVK.
> 
> The M.2 variant uses the external module connected through the Key-E
> connector instead of the onboard WCN3988 devices. Disable the onboard
> Wi-Fi and Bluetooth nodes when the overlay is selected so the device tree
> matches the hardware variant and does not probe the unavailable onboard
> connectivity path.

You already got a question on GitHub and ignored it there. Why are you
disaling onboard WiFi/BT? What makes it unavailable?

> 
> Describe the PCIe and UART connections through the M.2 connector, the
> 3.3 V supply, the W_DISABLE signals and the PCIe reset signal.
> 
> The Wi-Fi PCIe path was tested on a Shikra IQS EVK with a QCC2072
> module. The overlay was applied, the link trained at Gen2 x1 and the
> endpoint enumerated. Bluetooth UART and HCI runtime validation is
> pending.

Please don't send unvalidated patches.

> 
> Co-developed-by: Wei Deng <wei.deng@oss.qualcomm.com>
> Signed-off-by: Wei Deng <wei.deng@oss.qualcomm.com>
> Signed-off-by: Linghui Wu <linghui.wu@oss.qualcomm.com>
> ---
> Changes in v2:
> - Drop regulator-boot-on and startup-delay-us from the 3.3 V regulator.
> 
> Changes in v3:
> - Drop the unused reg override from the disabled TC9563 node.
> 
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso   | 105 +++++++++++++++++
>  2 files changed, 106 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 1c86e7e98f55..799faa32e2d9 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -339,6 +339,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdx75-idp.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-m2-wifi-bt.dtbo

How does the Makefile handle eother dtbos?

>  dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
> diff --git a/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
> new file mode 100644
> index 000000000000..9496c6558eef
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/shikra-iqs-evk-m2-wifi-bt.dtso
> @@ -0,0 +1,105 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2026 Qualcomm Technologies, Inc. and/or its subsidiaries.
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +&{/} {
> +	m2_keye_3p3: regulator-m2-keye-3p3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VREG_3P3_KEYE";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&qps_gpio_expander 6 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	wifi-bt-connector {
> +		compatible = "pcie-m2-e-connector";
> +
> +		vpcie3v3-supply = <&m2_keye_3p3>;
> +		w-disable1-gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
> +		w-disable2-gpios = <&tlmm 60 GPIO_ACTIVE_LOW>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				m2_e_pcie_ep: endpoint@0 {
> +					reg = <0>;
> +					remote-endpoint = <&pcie_port0_ep>;
> +				};
> +			};
> +
> +			port@3 {
> +				reg = <3>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				m2_e_uart_ep: endpoint@0 {
> +					reg = <0>;
> +					remote-endpoint = <&uart8_ep>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&{/wcn3988-pmu} {

Add a label to the PMU and update it by label rather than by the path.
If the path changes, this node, I think, will happily create a new one.
Using label will generate an error.

> +	status = "disabled";
> +};
> +
> +&i2c3 {
> +	qps_gpio_expander: gpio@3c {
> +		compatible = "nxp,pca9534";
> +		reg = <0x3c>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +	};
> +};
> +
> +&pcie {
> +	iommu-map = <0x0 &apps_smmu 0x0800 0x0 0x1>,
> +		    <0x100 &apps_smmu 0x0801 0x0 0x1>;
> +	vddpe-3v3-supply = <&m2_keye_3p3>;
> +};
> +
> +&pcie_port0 {
> +	compatible = "pciclass,0604";
> +	reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>;
> +
> +	port {
> +		pcie_port0_ep: endpoint {
> +			remote-endpoint = <&m2_e_pcie_ep>;
> +		};
> +	};
> +};
> +
> +&tc9563 {
> +	status = "disabled";
> +};
> +
> +&uart8 {
> +	bluetooth {
> +		status = "disabled";
> +	};
> +
> +	port {
> +		uart8_ep: endpoint {
> +			remote-endpoint = <&m2_e_uart_ep>;
> +		};
> +	};

How does the UART switch from the onboard WiFi/BT card to the M.2 slot?
Is ther an automatic switch?

> +};
> +
> +&wifi {
> +	status = "disabled";
> +};
> -- 
> 2.43.0

-- 
With best wishes
Dmitry