[PATCH v11 3/3] arm64: dts: rockchip: rk3568-photonicat: enable SGMII LAN port

[Coia Prant <coiaprant@gmail.com>]

The Ariaboard Photonicat has a Motorcomm YT8521SC Gigabit Ethernet PHY
connected to GMAC0 via XPCS SGMII.  Enable the necessary nodes to make
this port functional.

Enable the xpcs node, referencing combphy2 as the SerDes PHY.

The rockchip,sgmii-mac-sel property on combphy2 is not set here.  The
property is tri-state: when absent, the driver leaves the routing
unchanged.  If the bootloader has already routed combphy2 SGMII to
GMAC0, the link works without the explicit property.  A follow-up will
add rockchip,sgmii-mac-sel = <0> once the PHY binding lands in
linux-next, removing the dependency on the bootloader default.

RK3568 has three Combo PHYs that can carry SGMII; which one is wired
to the XPCS is a board-level choice, and Photonicat uses combphy2.

Add the mdio0 node with the YT8521SC PHY at address 3, including its
reset GPIO and LED configuration.

Signed-off-by: Coia Prant <coiaprant@gmail.com>
---
 .../boot/dts/rockchip/rk3568-photonicat.dts   | 48 ++++++++++++++++++-
 1 file changed, 46 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts b/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
index 12ae9159bea87..d9015dbfb9f5c 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
@@ -261,9 +261,18 @@ &cpu3 {
 	cpu-supply = <&vdd_cpu>;
 };
 
-/* Motorcomm YT8521SC LAN port (require SGMII) */
+/* Motorcomm YT8521SC LAN port */
 &gmac0 {
-	status = "disabled";
+	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>;
+	assigned-clock-parents = <&clk_gmac0_xpcs_mii>;
+	managed = "in-band-status";
+	pcs-handle = <&xpcs>;
+	phy-handle = <&sgmii_phy>;
+	phy-mode = "sgmii";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_miim>;
+	status = "okay";
 };
 
 /* Motorcomm YT8521SC WAN port */
@@ -342,6 +351,36 @@ &i2s0_8ch {
 	status = "okay";
 };
 
+&mdio0 {
+	sgmii_phy: ethernet-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x3>;
+		max-speed = <1000>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio3 RK_PC6 GPIO_ACTIVE_LOW>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+		};
+	};
+};
+
 &mdio1 {
 	rgmii_phy: ethernet-phy@3 {
 		compatible = "ethernet-phy-ieee802.3-c22";
@@ -606,3 +645,8 @@ &xin32k {
 	pinctrl-names = "default";
 	pinctrl-0 = <&clk32k_out1>;
 };
+
+&xpcs {
+	phys = <&combphy2 PHY_TYPE_SGMII>;
+	status = "okay";
+};
-- 
2.47.3