From: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
To: Andrew Lunn <andrew+netdev@lunn.ch>,
"David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Paolo Abeni <pabeni@redhat.com>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Richard Cochran <richardcochran@gmail.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@collabora.com>,
Biao Huang <biao.huang@mediatek.com>,
Maxime Chevallier <maxime.chevallier@bootlin.com>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@foss.st.com>,
Eric Dumazet <edumazet@kernel.org>,
Eric Dumazet <edumazet@kernel.org>
Cc: kernel@collabora.com, netdev@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-mediatek@lists.infradead.org,
linux-stm32@st-md-mailman.stormreply.com,
Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Subject: [PATCH net-next v4 08/10] net: stmmac: mediatek: add PERI_ETH_CTRLx register offset in platform data
Date: Tue, 03 Nov 2026 11:12:13 +0100 [thread overview]
Message-ID: <20261103-dwmac-mediatek-mt8189-v4-8-c86c14fc50f4@collabora.com> (raw)
In-Reply-To: <20261103-dwmac-mediatek-mt8189-v4-0-c86c14fc50f4@collabora.com>
In preparation of newer SoC support, that use like MT8195 the Ethernet
control registers from the peripheral configuration syscon but at a
different base offset, add a new base offset in the variant platform
data to access the PERI_ETH_CTRLx registers and use it in implemented
methods.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
---
.../net/ethernet/stmicro/stmmac/dwmac-mediatek.c | 26 ++++++++++++++++------
1 file changed, 19 insertions(+), 7 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
index 61bc1ff08cc4..0426a0876956 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
@@ -42,7 +42,9 @@
#define MT2712_RGMII_DELAY_MAX 5440 /* 32 x 170ps */
/* Peri Configuration register for mt8195 */
-#define MT8195_PERI_ETH_CTRL0 0xFD0
+#define MT8195_PERI_ETH_CTRL_OFFSET 0xFD0
+
+#define MT8195_PERI_ETH_CTRL0 0x0
#define MT8195_RMII_CLK_SRC_INTERNAL BIT(28)
#define MT8195_RMII_CLK_SRC_RXC BIT(27)
#define MT8195_ETH_INTF_SEL GENMASK(26, 24)
@@ -52,7 +54,7 @@
#define MT8195_DLY_GTXC_ENABLE BIT(5)
#define MT8195_DLY_GTXC_STAGES GENMASK(4, 0)
-#define MT8195_PERI_ETH_CTRL1 0xFD4
+#define MT8195_PERI_ETH_CTRL1 0x4
#define MT8195_DLY_RXC_INV BIT(25)
#define MT8195_DLY_RXC_ENABLE BIT(18)
#define MT8195_DLY_RXC_STAGES GENMASK(17, 13)
@@ -60,7 +62,7 @@
#define MT8195_DLY_TXC_ENABLE BIT(5)
#define MT8195_DLY_TXC_STAGES GENMASK(4, 0)
-#define MT8195_PERI_ETH_CTRL2 0xFD8
+#define MT8195_PERI_ETH_CTRL2 0x8
#define MT8195_DLY_RMII_RXC_INV BIT(25)
#define MT8195_DLY_RMII_RXC_ENABLE BIT(18)
#define MT8195_DLY_RMII_RXC_STAGES GENMASK(17, 13)
@@ -109,6 +111,7 @@ struct mediatek_dwmac_variant {
u32 rgmii_delay_max;
u16 mii_delay_stage_div;
u16 rgmii_delay_stage_div;
+ u32 peri_eth_ctrl_offset;
u8 dma_bit_mask;
};
@@ -292,6 +295,7 @@ static int mt8195_set_interface(struct mediatek_dwmac_plat_data *plat,
u8 phy_intf_sel)
{
u32 intf_val = FIELD_PREP(MT8195_ETH_INTF_SEL, phy_intf_sel);
+ u32 reg_offset = plat->variant->peri_eth_ctrl_offset;
if (phy_intf_sel == PHY_INTF_SEL_RMII) {
if (plat->rmii_clk_from_mac)
@@ -303,7 +307,9 @@ static int mt8195_set_interface(struct mediatek_dwmac_plat_data *plat,
/* MT8195 only support external PHY */
intf_val |= MT8195_EXT_PHY_MODE;
- regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL0, intf_val);
+ regmap_write(plat->peri_regmap,
+ reg_offset + MT8195_PERI_ETH_CTRL0,
+ intf_val);
return 0;
}
@@ -311,6 +317,7 @@ static int mt8195_set_interface(struct mediatek_dwmac_plat_data *plat,
static int mt8195_set_delay(struct mediatek_dwmac_plat_data *plat)
{
struct mac_delay_struct *mac_delay = &plat->mac_delay;
+ u32 reg_offset = plat->variant->peri_eth_ctrl_offset;
u32 rx_delay_stage_val, tx_delay_stage_val;
u32 gtxc_delay_val = 0;
u32 rmii_delay_val = 0;
@@ -410,14 +417,18 @@ static int mt8195_set_delay(struct mediatek_dwmac_plat_data *plat)
}
regmap_update_bits(plat->peri_regmap,
- MT8195_PERI_ETH_CTRL0,
+ reg_offset + MT8195_PERI_ETH_CTRL0,
MT8195_RGMII_TXC_PHASE_CTRL |
MT8195_DLY_GTXC_INV |
MT8195_DLY_GTXC_ENABLE |
MT8195_DLY_GTXC_STAGES,
gtxc_delay_val);
- regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL1, delay_val);
- regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL2, rmii_delay_val);
+ regmap_write(plat->peri_regmap,
+ reg_offset + MT8195_PERI_ETH_CTRL1,
+ delay_val);
+ regmap_write(plat->peri_regmap,
+ reg_offset + MT8195_PERI_ETH_CTRL2,
+ rmii_delay_val);
return 0;
}
@@ -432,6 +443,7 @@ static const struct mediatek_dwmac_variant mt8195_gmac_variant = {
.mii_delay_stage_div = MT8195_MII_DLY_STAGE_DIV,
.rgmii_delay_stage_div = MT8195_RGMII_DLY_STAGE_DIV,
.dma_bit_mask = 35,
+ .peri_eth_ctrl_offset = MT8195_PERI_ETH_CTRL_OFFSET,
};
static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
--
2.56.0
next prev parent reply other threads:[~2026-11-03 10:12 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-03 10:12 [PATCH net-next v4 00/10] net/stmmac: Add Mediatek MT8189 support Louis-Alexis Eyraud
2026-11-03 10:12 ` [PATCH net-next v4 01/10] dt-bindings: net: mediatek-dwmac: fix unit in rx/tx delay property description Louis-Alexis Eyraud
2026-11-03 10:12 ` [PATCH net-next v4 02/10] dt-bindings: net: mediatek-dwmac: deprecate rx/tx delay vendor properties Louis-Alexis Eyraud
2026-11-04 10:55 ` Krzysztof Kozlowski
2026-11-03 10:12 ` [PATCH net-next v4 03/10] dt-bindings: net: mediatek-dwmac: add support for MT8189 SoC Louis-Alexis Eyraud
2026-11-04 10:57 ` Krzysztof Kozlowski
2026-11-03 10:12 ` [PATCH net-next v4 04/10] net: stmmac: mediatek: simplify TX/RX delay handling in mt8195_set_delay Louis-Alexis Eyraud
2026-11-03 10:12 ` [PATCH net-next v4 05/10] net: stmmac: mediatek: simplify TX/RX delay handling in mt2712_set_delay Louis-Alexis Eyraud
2026-11-03 10:12 ` [PATCH net-next v4 06/10] net: stmmac: mediatek: use standard internal delay properties Louis-Alexis Eyraud
2026-11-03 10:12 ` [PATCH net-next v4 07/10] net: stmmac: mediatek: add RX/TX delay stage divider in platform data Louis-Alexis Eyraud
2026-11-03 10:12 ` Louis-Alexis Eyraud [this message]
2026-11-03 10:12 ` [PATCH net-next v4 09/10] net: stmmac: mediatek: add support for TX clock output enable feature Louis-Alexis Eyraud
2026-11-03 10:12 ` [PATCH net-next v4 10/10] net: stmmac: mediatek: add support for MT8189 SoC Louis-Alexis Eyraud
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261103-dwmac-mediatek-mt8189-v4-8-c86c14fc50f4@collabora.com \
--to=louisalexis.eyraud@collabora.com \
--cc=alexandre.torgue@foss.st.com \
--cc=andrew+netdev@lunn.ch \
--cc=angelogioacchino.delregno@collabora.com \
--cc=biao.huang@mediatek.com \
--cc=conor+dt@kernel.org \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=edumazet@kernel.org \
--cc=kernel@collabora.com \
--cc=krzk+dt@kernel.org \
--cc=kuba@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=matthias.bgg@gmail.com \
--cc=maxime.chevallier@bootlin.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=richardcochran@gmail.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®