[PATCH ath-next 1/2] wifi: ath12k: Fix HE BA mode configuration for AP mode

[Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>]

WMI_VDEV_PARAM_BA_MODE is currently configured inside the he_oper.params
check. However, mac80211 does not populate he_oper.params for AP mode,
causing the BA mode configuration to be skipped for HE AP operation.

Move the BA mode configuration outside the he_oper.params check so that
it is applied whenever HE support is enabled.
Without this change, firmware defaults to a BA buffer size of 64
(legacy mode) for HE associations.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.6-01243-QCAHKSWPL_SILICONZ-1

Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
---
 drivers/net/wireless/ath/ath12k/mac.c | 27 +++++++++++++++------------
 1 file changed, 15 insertions(+), 12 deletions(-)

diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 4f16c78b52a8..711acb32a6ca 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -4888,8 +4888,7 @@ static void ath12k_mac_bss_info_changed(struct ath12k *ar,
 		}
 		ath12k_control_beaconing(arvif, info);
 
-		if (arvif->is_up && info->he_support &&
-		    info->he_oper.params) {
+		if (arvif->is_up && info->he_support) {
 			/* TODO: Extend to support 1024 BA Bitmap size */
 			ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
 							    WMI_VDEV_PARAM_BA_MODE,
@@ -4899,17 +4898,21 @@ static void ath12k_mac_bss_info_changed(struct ath12k *ar,
 					    "failed to set BA BUFFER SIZE 256 for vdev: %d\n",
 					    arvif->vdev_id);
 
-			param_id = WMI_VDEV_PARAM_HEOPS_0_31;
-			param_value = info->he_oper.params;
-			ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
-							    param_id, param_value);
-			ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
-				   "he oper param: %x set for VDEV: %d\n",
-				   param_value, arvif->vdev_id);
+			if (info->he_oper.params) {
+				param_id = WMI_VDEV_PARAM_HEOPS_0_31;
+				param_value = info->he_oper.params;
 
-			if (ret)
-				ath12k_warn(ar->ab, "Failed to set he oper params %x for VDEV %d: %i\n",
-					    param_value, arvif->vdev_id, ret);
+				ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
+								    param_id,
+								    param_value);
+				ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
+					   "he oper param: %x set for VDEV: %d\n",
+					   param_value, arvif->vdev_id);
+
+				if (ret)
+					ath12k_warn(ar->ab, "Failed to set he oper params %x for VDEV %d: %i\n",
+						    param_value, arvif->vdev_id, ret);
+			}
 		}
 	}
 

-- 
2.34.1