[PATCH v3 1/3] arm64: dts: qcom: lemans: add CSI2 D-PHY common-phy providers

[Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>]

Expose the four SA8775p CSIPHYs as standalone qcom,sa8775p-csi2-phy
generic-PHY provider nodes (csiphy0..3) at their existing register
addresses, each with its own OF graph (port@0 sensor-facing, port@1
CAMSS-facing) so camss_detect_legacy_phy() picks the non-legacy path
once a board wires a sensor through one of them. The camss node's own
reg-names/clocks/interrupts for the CSIPHYs are unchanged, so boards
that don't use a provider still get the legacy binding.

csiphy0..3 are placed after camss (ac78000 < ac9c000..aca2000), so
soc@0's children stay sorted by ascending unit address. Their shared
OPP table lives at the root node, not inside soc@0 (a simple-bus),
since it has no reg/ranges property of its own; it only lists
400000000 Hz, the one rate SA8775P's camcc clock driver actually
supports for this clock (ftbl_cam_cc_cphy_rx_clk_src has no 300 MHz
entry).

The provider nodes are disabled by default; a board or camera overlay
enables the one(s) it uses.

Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>
Signed-off-by: Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/lemans.dtsi | 136 +++++++++++++++++++++++++++
 1 file changed, 136 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/lemans.dtsi b/arch/arm64/boot/dts/qcom/lemans.dtsi
index 1fdb72fa5518..6909dfa06d86 100644
--- a/arch/arm64/boot/dts/qcom/lemans.dtsi
+++ b/arch/arm64/boot/dts/qcom/lemans.dtsi
@@ -545,6 +545,14 @@ opp-100000000 {
 		};
 	};
 
+	csiphy_opp_table: opp-table-csiphy {
+		compatible = "operating-points-v2";
+
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+		};
+	};
+
 	pmu {
 		compatible = "arm,armv8-pmuv3";
 		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
@@ -5348,6 +5356,134 @@ port@3 {
 			};
 		};
 
+		csiphy0: phy@ac9c000 {
+			compatible = "qcom,sa8775p-csi2-phy";
+			reg = <0x0 0x0ac9c000 0x0 0x2000>;
+
+			clocks = <&camcc CAM_CC_CSIPHY0_CLK>,
+				 <&camcc CAM_CC_CSI0PHYTIMER_CLK>;
+			clock-names = "core",
+				      "timer";
+
+			interrupts = <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>;
+
+			operating-points-v2 = <&csiphy_opp_table>;
+
+			power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+			power-domain-names = "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		csiphy1: phy@ac9e000 {
+			compatible = "qcom,sa8775p-csi2-phy";
+			reg = <0x0 0x0ac9e000 0x0 0x2000>;
+
+			clocks = <&camcc CAM_CC_CSIPHY1_CLK>,
+				 <&camcc CAM_CC_CSI1PHYTIMER_CLK>;
+			clock-names = "core",
+				      "timer";
+
+			interrupts = <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>;
+
+			operating-points-v2 = <&csiphy_opp_table>;
+
+			power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+			power-domain-names = "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		csiphy2: phy@aca0000 {
+			compatible = "qcom,sa8775p-csi2-phy";
+			reg = <0x0 0x0aca0000 0x0 0x2000>;
+
+			clocks = <&camcc CAM_CC_CSIPHY2_CLK>,
+				 <&camcc CAM_CC_CSI2PHYTIMER_CLK>;
+			clock-names = "core",
+				      "timer";
+
+			interrupts = <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>;
+
+			operating-points-v2 = <&csiphy_opp_table>;
+
+			power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+			power-domain-names = "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		csiphy3: phy@aca2000 {
+			compatible = "qcom,sa8775p-csi2-phy";
+			reg = <0x0 0x0aca2000 0x0 0x2000>;
+
+			clocks = <&camcc CAM_CC_CSIPHY3_CLK>,
+				 <&camcc CAM_CC_CSI3PHYTIMER_CLK>;
+			clock-names = "core",
+				      "timer";
+
+			interrupts = <GIC_SPI 448 IRQ_TYPE_EDGE_RISING>;
+
+			operating-points-v2 = <&csiphy_opp_table>;
+
+			power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+			power-domain-names = "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
 		camcc: clock-controller@ade0000 {
 			compatible = "qcom,sa8775p-camcc";
 			reg = <0x0 0x0ade0000 0x0 0x20000>;
-- 
2.34.1