[PATCH v3 2/3] arm64: dts: qcom: monaco: add CSI2 PHY common-phy providers

[Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>]

Expose the three QCS8300 CSIPHYs as standalone
qcom,qcs8300-csi2-phy generic-PHY provider nodes (csiphy0..2) at their
existing register addresses, each with its own OF graph (port@0
sensor-facing, port@1 CAMSS-facing) so camss_detect_legacy_phy() picks
the non-legacy path once a board wires a sensor through one of them.
The camss node's own reg-names/clocks/interrupts for the CSIPHYs are
unchanged, so boards that don't use a provider still get the legacy
binding.

csiphy0..2 drop the extra "csiphy_rx" clock: QCS8300 binds through the
sa8775p soc_cfg (no dedicated QCS8300 camcc driver exists), which only
declares two clocks ("core", "timer") for this PHY, not three.

csiphy_opp_table moves to the root node, not inside soc@0 (a
simple-bus), since it has no reg/ranges property of its own; its
opp-300000000 entry is dropped too, since QCS8300 shares SA8775P's
camcc, whose cam_cc_cphy_rx_clk_src only defines a 400 MHz rate.

The provider nodes are disabled by default; a board or camera overlay
enables the one(s) it uses.

Reviewed-by: Jigarkumar Zala <jigarkumar.zala@oss.qualcomm.com>
Signed-off-by: Anusha Arun Nandi <anusha.nandi@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/monaco.dtsi | 104 +++++++++++++++++++++++++++
 1 file changed, 104 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/monaco.dtsi b/arch/arm64/boot/dts/qcom/monaco.dtsi
index 35fbee63d4c6..a66c04a1d306 100644
--- a/arch/arm64/boot/dts/qcom/monaco.dtsi
+++ b/arch/arm64/boot/dts/qcom/monaco.dtsi
@@ -644,6 +644,14 @@ opp-120000000 {
 		};
 	};
 
+	csiphy_opp_table: opp-table-csiphy {
+		compatible = "operating-points-v2";
+
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+		};
+	};
+
 	pmu-a55 {
 		compatible = "arm,cortex-a55-pmu";
 		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
@@ -5577,6 +5585,102 @@ cci2_i2c1: i2c-bus@1 {
 			};
 		};
 
+		csiphy0: phy@ac9c000 {
+			compatible = "qcom,qcs8300-csi2-phy";
+			reg = <0x0 0x0ac9c000 0x0 0x2000>;
+
+			clocks = <&camcc CAM_CC_CSIPHY0_CLK>,
+				 <&camcc CAM_CC_CSI0PHYTIMER_CLK>;
+			clock-names = "core",
+				      "timer";
+
+			interrupts = <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>;
+
+			operating-points-v2 = <&csiphy_opp_table>;
+
+			power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+			power-domain-names = "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		csiphy1: phy@ac9e000 {
+			compatible = "qcom,qcs8300-csi2-phy";
+			reg = <0x0 0x0ac9e000 0x0 0x2000>;
+
+			clocks = <&camcc CAM_CC_CSIPHY1_CLK>,
+				 <&camcc CAM_CC_CSI1PHYTIMER_CLK>;
+			clock-names = "core",
+				      "timer";
+
+			interrupts = <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>;
+
+			operating-points-v2 = <&csiphy_opp_table>;
+
+			power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+			power-domain-names = "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		csiphy2: phy@aca0000 {
+			compatible = "qcom,qcs8300-csi2-phy";
+			reg = <0x0 0x0aca0000 0x0 0x2000>;
+
+			clocks = <&camcc CAM_CC_CSIPHY2_CLK>,
+				 <&camcc CAM_CC_CSI2PHYTIMER_CLK>;
+			clock-names = "core",
+				      "timer";
+
+			interrupts = <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>;
+
+			operating-points-v2 = <&csiphy_opp_table>;
+
+			power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+			power-domain-names = "top";
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
 		camss: isp@ac78000 {
 			compatible = "qcom,qcs8300-camss";
 
-- 
2.34.1