[PATCH net-next v2 4/7] net: phy: adin1100: Add separate driver entries for ADIN1110/ADIN2111

[Iustin Stolniceanu <iustin.stolniceanu@analog.com>]

The ADIN1100, ADIN1110 and ADIN2111 report different model numbers in
bits [9:4] of PHY_ID2 (0x8, 0x9 and 0xa), with the silicon revision in
bits [3:0]. A single phy_driver entry with the 0xffffffcf mask currently
binds all three by ignoring bits [5:4] of the model number.

Use one phy_driver entry per device, matched with PHY_ID_MATCH_MODEL(),
as is already done in the mdio_device_id table. This allows device
specific callbacks to be set in a following patch. The callbacks are
unchanged, so this is not a functional change apart from the reported
driver name.

Signed-off-by: Iustin Stolniceanu <iustin.stolniceanu@analog.com>
---
 drivers/net/phy/adin1100.c | 35 +++++++++++++++++++++++++++++++++--
 1 file changed, 33 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/adin1100.c b/drivers/net/phy/adin1100.c
index 8f9753d4318c..b946cb86b6c4 100644
--- a/drivers/net/phy/adin1100.c
+++ b/drivers/net/phy/adin1100.c
@@ -322,8 +322,7 @@ static int adin_probe(struct phy_device *phydev)
 
 static struct phy_driver adin_driver[] = {
 	{
-		.phy_id			= PHY_ID_ADIN1100,
-		.phy_id_mask		= 0xffffffcf,
+		PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100),
 		.name			= "ADIN1100",
 		.get_features		= adin_get_features,
 		.soft_reset		= adin_soft_reset,
@@ -338,6 +337,38 @@ static struct phy_driver adin_driver[] = {
 		.get_sqi		= adin_get_sqi,
 		.get_sqi_max		= adin_get_sqi_max,
 	},
+	{
+		PHY_ID_MATCH_MODEL(PHY_ID_ADIN1110),
+		.name			= "ADIN1110",
+		.get_features		= adin_get_features,
+		.soft_reset		= adin_soft_reset,
+		.probe			= adin_probe,
+		.config_aneg		= adin_config_aneg,
+		.read_status		= adin_read_status,
+		.config_intr		= adin_config_intr,
+		.handle_interrupt	= adin_phy_handle_interrupt,
+		.set_loopback		= adin_set_loopback,
+		.suspend		= adin_suspend,
+		.resume			= adin_resume,
+		.get_sqi		= adin_get_sqi,
+		.get_sqi_max		= adin_get_sqi_max,
+	},
+	{
+		PHY_ID_MATCH_MODEL(PHY_ID_ADIN2111),
+		.name			= "ADIN2111",
+		.get_features		= adin_get_features,
+		.soft_reset		= adin_soft_reset,
+		.probe			= adin_probe,
+		.config_aneg		= adin_config_aneg,
+		.read_status		= adin_read_status,
+		.config_intr		= adin_config_intr,
+		.handle_interrupt	= adin_phy_handle_interrupt,
+		.set_loopback		= adin_set_loopback,
+		.suspend		= adin_suspend,
+		.resume			= adin_resume,
+		.get_sqi		= adin_get_sqi,
+		.get_sqi_max		= adin_get_sqi_max,
+	},
 };
 
 module_phy_driver(adin_driver);
-- 
2.43.0