From: Iustin Stolniceanu <iustin.stolniceanu@analog.com>
To: Andrew Lunn <andrew+netdev@lunn.ch>,
"David S. Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@kernel.org>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Parthiban Veerasooran <parthiban.veerasooran@microchip.com>,
Heiner Kallweit <hkallweit1@gmail.com>,
Russell King <linux@armlinux.org.uk>,
Marcelo Schmitt <marcelo.schmitt@analog.com>
Cc: "Alvin Šipraga" <alvin.sipraga@analog.com>,
"Ciprian Regus" <ciprian.regus@analog.com>,
netdev@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
"Iustin Stolniceanu" <iustin.stolniceanu@analog.com>
Subject: [PATCH net-next v2 6/7] dt-bindings: net: adi,adin1110: Add adi,spi-oa-tc6
Date: Mon, 9 Nov 2026 10:59:51 +0200 [thread overview]
Message-ID: <20261109085952.105331-7-iustin.stolniceanu@analog.com> (raw)
In-Reply-To: <20261109085952.105331-1-iustin.stolniceanu@analog.com>
From: Ciprian Regus <ciprian.regus@analog.com>
The ADIN1110 and ADIN2111 support two SPI host interface protocols:
the generic SPI protocol and the OPEN Alliance TC6 protocol. The
protocol is selected by the state of the SPI_CFG1 pin, which the device
latches when it comes out of reset, together with SPI_CFG0, which
selects CRC (generic SPI) or protection (OPEN Alliance) mode.
The protocol is set by the board hardware, so the driver must know it
in advance. Add a boolean property to describe a device configured for
the OPEN Alliance TC6 protocol. Without it, the generic SPI protocol is
assumed, as before.
adi,spi-crc enables the CRC of the generic SPI protocol, so it is not
allowed together with adi,spi-oa-tc6. The OPEN Alliance protection mode
needs no property, as the driver reads it from the PROTE bit in CONFIG0.
Signed-off-by: Ciprian Regus <ciprian.regus@analog.com>
Signed-off-by: Iustin Stolniceanu <iustin.stolniceanu@analog.com>
---
.../devicetree/bindings/net/adi,adin1110.yaml | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/adi,adin1110.yaml b/Documentation/devicetree/bindings/net/adi,adin1110.yaml
index 0a73e01d7f97..fa30787c663d 100644
--- a/Documentation/devicetree/bindings/net/adi,adin1110.yaml
+++ b/Documentation/devicetree/bindings/net/adi,adin1110.yaml
@@ -28,6 +28,12 @@ description: |
allOf:
- $ref: ethernet-controller.yaml#
- $ref: /schemas/spi/spi-peripheral-props.yaml#
+ - if:
+ required:
+ - adi,spi-oa-tc6
+ then:
+ properties:
+ adi,spi-crc: false
properties:
compatible:
@@ -43,6 +49,12 @@ properties:
Enable CRC8 checks on SPI read/writes.
type: boolean
+ adi,spi-oa-tc6:
+ description: |
+ The device is configured, through the SPI_CFG1 pin, for the
+ OPEN Alliance TC6 protocol instead of the generic SPI one.
+ type: boolean
+
interrupts:
maxItems: 1
--
2.43.0
next prev parent reply other threads:[~2026-11-09 9:01 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-09 8:59 [PATCH net-next v2 0/7] net: ethernet: adi: adin1110: Add OPEN Alliance TC6 support Iustin Stolniceanu
2026-11-09 8:59 ` [PATCH net-next v2 1/7] net: ethernet: oa_tc6: Forward declare struct mii_bus Iustin Stolniceanu
2026-11-09 8:59 ` [PATCH net-next v2 2/7] net: ethernet: oa_tc6: Allow custom reset settle time values Iustin Stolniceanu
2026-11-09 8:59 ` [PATCH net-next v2 3/7] net: ethernet: oa_tc6: Add support for MDIO indirect access Iustin Stolniceanu
2026-11-09 8:59 ` [PATCH net-next v2 4/7] net: phy: adin1100: Add separate driver entries for ADIN1110/ADIN2111 Iustin Stolniceanu
2026-11-09 8:59 ` [PATCH net-next v2 5/7] net: phy: adin1100: Skip the soft reset on ADIN1110/ADIN2111 Iustin Stolniceanu
2026-11-09 8:59 ` Iustin Stolniceanu [this message]
2026-11-09 8:59 ` [PATCH net-next v2 7/7] net: ethernet: adi: adin1110: Add OA TC6 protocol support for ADIN1110 Iustin Stolniceanu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261109085952.105331-7-iustin.stolniceanu@analog.com \
--to=iustin.stolniceanu@analog.com \
--cc=alvin.sipraga@analog.com \
--cc=andrew+netdev@lunn.ch \
--cc=ciprian.regus@analog.com \
--cc=conor+dt@kernel.org \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=edumazet@kernel.org \
--cc=hkallweit1@gmail.com \
--cc=krzk+dt@kernel.org \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=marcelo.schmitt@analog.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=parthiban.veerasooran@microchip.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®