* [PATCH v2] ARM: dts: aspeed: yosemite4: Remove Floating Falls board nodes
@ 2026-11-11 10:04 Eric Yang via B4 Relay
0 siblings, 0 replies; only message in thread
From: Eric Yang via B4 Relay @ 2026-11-11 10:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Joel Stanley,
Andrew Jeffery, Ryan Chen, Billy Tsai, patrick
Cc: devicetree, linux-arm-kernel, linux-aspeed, linux-kernel,
Sean He, Eric Yang
From: Sean He <sean.he.wiwynn@gmail.com>
The Floating Falls (FF) board connects to the Sentinel Dome through a
connector and carries a PCA9537 GPIO expander at address 0x49 and a FRU
EEPROM at address 0x50 on each slot I2C bus. No system currently in use
has an FF board, and its connector on the Sentinel Dome is not populated,
so these addresses never acknowledge: the pca953x driver fails to probe
the eight PCA9537 nodes on every boot and the at24 driver does not bind
to the eight EEPROM nodes. Remove the nodes so that the devicetree
matches the actual hardware.
Signed-off-by: Sean He <sean.he.wiwynn@gmail.com>
Signed-off-by: Eric Yang <eric.yang.wiwynn@gmail.com>
---
The changelog was drafted with an AI assistant (Claude Code) and
reviewed by the submitter.
---
Changes in v2:
- Reworded the commit message: the FF board is a separate board, no
system in use has it, and its connector is not populated
- Dropped the verification paragraph
- Link to v1: https://lore.kernel.org/r/20261105-yv4-remove-ff-nodes-v1-1-aa707a9577b7@gmail.com
---
.../dts/aspeed/aspeed-bmc-facebook-yosemite4.dts | 96 ----------------------
1 file changed, 96 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index e4172be84..4c7c96ce4 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -604,18 +604,6 @@ imux16: i2c@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
- gpio@49 {
- compatible = "nxp,pca9537";
- reg = <0x49>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c128";
- reg = <0x50>;
- };
-
eeprom@51 {
compatible = "atmel,24c128";
reg = <0x51>;
@@ -631,18 +619,6 @@ imux17: i2c@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
- gpio@49 {
- compatible = "nxp,pca9537";
- reg = <0x49>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c128";
- reg = <0x50>;
- };
-
eeprom@51 {
compatible = "atmel,24c128";
reg = <0x51>;
@@ -658,18 +634,6 @@ imux18: i2c@2 {
reg = <2>;
#address-cells = <1>;
#size-cells = <0>;
- gpio@49 {
- compatible = "nxp,pca9537";
- reg = <0x49>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c128";
- reg = <0x50>;
- };
-
eeprom@51 {
compatible = "atmel,24c128";
reg = <0x51>;
@@ -685,18 +649,6 @@ imux19: i2c@3 {
reg = <3>;
#address-cells = <1>;
#size-cells = <0>;
- gpio@49 {
- compatible = "nxp,pca9537";
- reg = <0x49>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c128";
- reg = <0x50>;
- };
-
eeprom@51 {
compatible = "atmel,24c128";
reg = <0x51>;
@@ -726,18 +678,6 @@ imux20: i2c@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
- gpio@49 {
- compatible = "nxp,pca9537";
- reg = <0x49>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c128";
- reg = <0x50>;
- };
-
eeprom@51 {
compatible = "atmel,24c128";
reg = <0x51>;
@@ -753,18 +693,6 @@ imux21: i2c@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
- gpio@49 {
- compatible = "nxp,pca9537";
- reg = <0x49>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c128";
- reg = <0x50>;
- };
-
eeprom@51 {
compatible = "atmel,24c128";
reg = <0x51>;
@@ -780,18 +708,6 @@ imux22: i2c@2 {
reg = <2>;
#address-cells = <1>;
#size-cells = <0>;
- gpio@49 {
- compatible = "nxp,pca9537";
- reg = <0x49>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c128";
- reg = <0x50>;
- };
-
eeprom@51 {
compatible = "atmel,24c128";
reg = <0x51>;
@@ -807,18 +723,6 @@ imux23: i2c@3 {
reg = <3>;
#address-cells = <1>;
#size-cells = <0>;
- gpio@49 {
- compatible = "nxp,pca9537";
- reg = <0x49>;
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- eeprom@50 {
- compatible = "atmel,24c128";
- reg = <0x50>;
- };
-
eeprom@51 {
compatible = "atmel,24c128";
reg = <0x51>;
---
base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4
change-id: 20261103-yv4-remove-ff-nodes-9e20104d2362
Best regards,
--
Eric Yang <eric.yang.wiwynn@gmail.com>
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2026-11-11 10:04 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-11-11 10:04 [PATCH v2] ARM: dts: aspeed: yosemite4: Remove Floating Falls board nodes Eric Yang via B4 Relay
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®