[PATCH 0/3] arm64: dts: allwinner: add Radxa Cubie A7Z support

[PATCH 0/3] arm64: dts: allwinner: add Radxa Cubie A7Z support

[Vinicius Pedrosa]

Add a board DT for the Radxa Cubie A7Z (Allwinner A733), based on Enzo's
A733 SoC description and Cubie A7S DT [1].

The A7Z differs from the A7S in its PG supply (BLDO5), the SY8089
regulator feeding the PMIC's BLDO and CLDO inputs, and the microSD
card-detect line, which has an external pull-up. The series enables
UART0, the AXP318W PMIC, MMC0, RTC, bank supplies and the green user LED.

Tested on a Cubie A7Z with v7.4-rc1 and the posted A733 prerequisites.
Eight CPUs, R-I2C0/PMIC, MMC0 read/write at 3.3 V, RTC, LED, PSCI
reboot/power-off and CPU hotplug worked.

MMC0 card-detect hotplug needs the separate A733 EINT-mux fix [8]. The
tested DTB also had a local 16 MiB no-map reservation for my boot
firmware, which is not part of this series.

Dependencies:
[1] https://lore.kernel.org/r/cover.1794227241.git.enzo.adriano.code@gmail.com
[2] https://lore.kernel.org/r/20261009-a733-clk-v6-0-ae8178fce7e8@pigmoral.tech
[3] https://lore.kernel.org/r/20260910-axp318-regulator-v8-0-e906a61a7f3d@baylibre.com
[4] https://lore.kernel.org/r/20261025142412.112216-1-pmazzini@gmail.com
[5] https://lore.kernel.org/r/cover.1792439398.git.vinicius.eduardo.pedrosa@gmail.com
[6] https://lore.kernel.org/r/20261109-a733-pinctrl-v3@gmail.com
[7] https://lore.kernel.org/r/20261031020640-263f7b05-a7s-clock@gmail.com
[8] https://lore.kernel.org/r/20261110130157.112155-1-vinicius.eduardo.pedrosa@gmail.com

Vinicius Pedrosa (3):
  dt-bindings: arm: sunxi: document Radxa Cubie A7Z
  arm64: dts: allwinner: add Radxa Cubie A7Z board
  arm64: dts: allwinner: sun60i-a733-cubie-a7z: add the user LED

 .../devicetree/bindings/arm/sunxi.yaml        |   5 +
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun60i-a733-cubie-a7z.dts   | 298 ++++++++++++++++++
 3 files changed, 304 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7z.dts


base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4
prerequisite-patch-id: 0ed6b92774b5b794761c7ce34db653a5435dc833
prerequisite-patch-id: 27ed3814dbd0c7ad830532ff125625917c873b4b
prerequisite-patch-id: 74d03898c5ce14763f4e89fb73e021de59f0fb9f
prerequisite-patch-id: 9225cb094cf6cbb338b14ac63711d68bed12d24d
prerequisite-patch-id: 568dae1c91a0d7318d6eb14a18054343b84b603a
prerequisite-patch-id: ff3806332e741f0e2c8dac1c11f4c71449c16c8c
prerequisite-patch-id: 39461e0543aefb5c40184664625cbab19ac8408a
prerequisite-patch-id: 6fc03bfbd343042dd3b660938fcc09c5e7d48314
prerequisite-patch-id: e27ef0b1e3a7fc0a659a1a82c1a7184665451265
prerequisite-patch-id: c598480f753e36b7f6230129b864c559b9f185d5
prerequisite-patch-id: f86b468a896a40f132adfcba885700327dff1bc5
prerequisite-patch-id: 079d60101e1b9e5425458060314bde3e9cc2fe4c
prerequisite-patch-id: 5d657469bcf35ca76bbe291203363403e00fab54
prerequisite-patch-id: 85db03df3394cdcb2780a0da122a74b2c1fe220d
prerequisite-patch-id: a3e883da50bf03e8f522444def66fec7f996ffbe
prerequisite-patch-id: c6889699a6dc13c336ce4cf4659e21b551e9a9fc
prerequisite-patch-id: af0aebcae7c38d58354925119c412178b5821b5e
prerequisite-patch-id: beb8a098ba14724e316ff243bdf8e00e729243c1
prerequisite-patch-id: 63342c5ec38e8eb9e55c8c74d3c5a81a630d5f69
prerequisite-patch-id: 1dc8d70f80674c98b2b15d09556dd27f643b20da
prerequisite-patch-id: cf6d9a8d3f2089f59a8a5afb4cc9375d7a6dc482
prerequisite-patch-id: 4cdaae8c384016491ce01e6e328acbb347debd62
prerequisite-patch-id: cb253a02b7d81079cc1ea4f75def94564468c80c
prerequisite-patch-id: 1f869e65014f3cd678bab7f235cbcb14c60a1608
prerequisite-patch-id: 184825f979a16a0b6900c58ba342899747da11b4
-- 
2.43.0

[PATCH 1/3] dt-bindings: arm: sunxi: document Radxa Cubie A7Z

[Vinicius Pedrosa]

Document the Radxa Cubie A7Z, an Allwinner A733-based board.

Signed-off-by: Vinicius Pedrosa <vinicius.eduardo.pedrosa@gmail.com>
---
 Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 37a7d713ac71..2b9e4d3b2fe7 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -862,6 +862,11 @@ properties:
           - const: radxa,cubie-a7s
           - const: allwinner,sun60i-a733
 
+      - description: Radxa Cubie A7Z
+        items:
+          - const: radxa,cubie-a7z
+          - const: allwinner,sun60i-a733
+
       - description: Remix Mini PC
         items:
           - const: jide,remix-mini-pc
-- 
2.43.0

[PATCH 2/3] arm64: dts: allwinner: add Radxa Cubie A7Z board

[Vinicius Pedrosa]

Add the device tree for the Radxa Cubie A7Z. Describe UART0, the AXP318W
PMIC over R-I2C0, MMC0, RTC and the bank supplies. It is based on the
Cubie A7S DT.

Unlike the A7S, this board uses BLDO5 for PG and a SY8089 regulator for
the PMIC's BLDO and CLDO inputs, and the microSD card-detect line has an
external pull-up, so no internal pull-down is used. ELDO1 only supplies
VDD2L for LPDDR5 and this board uses LPDDR4, so it is not described.
SWOUT1 only feeds ports D and J on the 40-pin header, so it is not kept
always-on.

Signed-off-by: Vinicius Pedrosa <vinicius.eduardo.pedrosa@gmail.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun60i-a733-cubie-a7z.dts   | 286 ++++++++++++++++++
 2 files changed, 287 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7z.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 792152525b43..2eee91dcbd77 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -69,3 +69,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun55i-h728-x96qpro+.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-avaota-a1.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-orangepi-4a.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun60i-a733-cubie-a7s.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun60i-a733-cubie-a7z.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7z.dts b/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7z.dts
new file mode 100644
index 000000000000..ab3d3d70f9ff
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7z.dts
@@ -0,0 +1,286 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/dts-v1/;
+
+#include "sun60i-a733.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Radxa Cubie A7Z";
+	compatible = "radxa,cubie-a7z", "allwinner,sun60i-a733";
+
+	aliases {
+		mmc0 = &mmc0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_ps: regulator-system-power {
+		compatible = "regulator-fixed";
+		regulator-name = "ps";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_ldo_input: regulator-ldo-input {
+		compatible = "regulator-fixed";
+		regulator-name = "ldo2v5-input";
+		/* SY8089: 0.6 V * (1 + RP11 / RP6), 30k / 10k. */
+		regulator-min-microvolt = <2400000>;
+		regulator-max-microvolt = <2400000>;
+		regulator-always-on;
+		vin-supply = <&reg_ps>;
+	};
+
+	osc32k: osc32k-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc5>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_dcdc5>;
+};
+
+&cpu2 {
+	cpu-supply = <&reg_dcdc5>;
+};
+
+&cpu3 {
+	cpu-supply = <&reg_dcdc5>;
+};
+
+&cpu4 {
+	cpu-supply = <&reg_dcdc5>;
+};
+
+&cpu5 {
+	cpu-supply = <&reg_dcdc5>;
+};
+
+&cpu6 {
+	cpu-supply = <&reg_dcdc3>;
+};
+
+&cpu7 {
+	cpu-supply = <&reg_dcdc3>;
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	/* PF6 has an external 10k pull-up and reads high with a card. */
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
+	disable-wp;
+	max-frequency = <50000000>;
+	no-1-8-v;
+	vmmc-supply = <&reg_swout2>;
+	/* The 3.3 V path uses VCC-IO; no Port F voltage switching yet. */
+	vqmmc-supply = <&reg_swout2>;
+	status = "okay";
+};
+
+&osc {
+	clock-frequency = <26000000>;
+};
+
+&pio {
+	vcc-pb-supply = <&reg_swout2>;
+	vcc-pc-supply = <&reg_cldo5>;
+	vcc-pd-supply = <&reg_swout1>;
+	vcc-pe-supply = <&reg_bldo1>;
+	/* CLDO5 feeds VCC18-PF; the 3.3 V path uses VCC-IO. */
+	vcc-pf-supply = <&reg_cldo5>;
+	vcc-pg-supply = <&reg_bldo5>;
+	vcc-ph-supply = <&reg_swout2>;
+	vcc-pj-supply = <&reg_swout1>;
+	vcc-pk-supply = <&reg_bldo1>;
+};
+
+&r_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_i2c0_pl_pins>;
+
+	axp318w: pmic@36 {
+		compatible = "x-powers,axp318w";
+		reg = <0x36>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		aldo156in-supply = <&reg_ps>;
+		aldo234in-supply = <&reg_aldo1>;
+		bldoin-supply = <&reg_ldo_input>;
+		cldoin-supply = <&reg_ldo_input>;
+		dldoin-supply = <&reg_ps>;
+		eldoin-supply = <&reg_dcdc9>;
+		ips-supply = <&reg_ps>;
+		vin19-supply = <&reg_ps>;
+		vin23-supply = <&reg_ps>;
+		vin45-supply = <&reg_ps>;
+		vin678-supply = <&reg_ps>;
+
+		regulators {
+			reg_dcdc1: dcdc1 {
+				regulator-name = "vcc-3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			reg_dcdc2: dcdc2 {
+				regulator-name = "vdd-sys";
+				regulator-always-on;
+			};
+
+			reg_dcdc3: dcdc3 {
+				regulator-name = "vdd-cpub";
+				regulator-always-on;
+			};
+
+			reg_dcdc4: dcdc4 {
+				regulator-name = "vdd-gpu";
+				regulator-always-on;
+			};
+
+			reg_dcdc5: dcdc5 {
+				regulator-name = "vdd-cpul";
+				regulator-always-on;
+			};
+
+			reg_dcdc6: dcdc6 {
+				regulator-name = "vcc-draml";
+				regulator-always-on;
+			};
+
+			reg_dcdc7: dcdc7 {
+				regulator-name = "vcc-dram";
+				regulator-always-on;
+			};
+
+			reg_dcdc8: dcdc8 {
+				regulator-name = "vcc-ufs-io";
+				regulator-always-on;
+			};
+
+			reg_dcdc9: dcdc9 {
+				regulator-name = "eldo-input";
+				regulator-always-on;
+			};
+
+			reg_swout1: swout1 {
+				regulator-name = "vcc33-lcd";
+			};
+
+			reg_swout2: swout2 {
+				regulator-name = "vcc-io-card";
+				regulator-always-on;
+			};
+
+			reg_aldo1: aldo1 {
+				regulator-name = "vcc-pl";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-name = "vcc-pe-pk-mcsi";
+			};
+
+			reg_bldo2: bldo2 {
+				regulator-name = "vcc-lvds0";
+				regulator-always-on;
+			};
+
+			reg_bldo4: bldo4 {
+				regulator-name = "vcc18-codec";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			reg_bldo5: bldo5 {
+				regulator-name = "vcc-pg";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			reg_cldo1: cldo1 {
+				regulator-name = "vcc33-18-usb";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			reg_cldo2: cldo2 {
+				regulator-name = "vcc18-hdmi";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			reg_cldo3: cldo3 {
+				regulator-name = "vcc-pll-dram";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			reg_cldo5: cldo5 {
+				regulator-name = "vcc18-pf-pc";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			reg_dldo1: dldo1 {
+				regulator-name = "vcc-efuse";
+				regulator-always-on;
+			};
+
+			reg_dldo6: dldo6 {
+				regulator-name = "vcc-ufs";
+				regulator-always-on;
+			};
+
+			reg_eldo6: eldo6 {
+				regulator-name = "vdd-cpus";
+				regulator-always-on;
+			};
+
+			reg_rtc_ldo: rtc-ldo {
+				regulator-name = "vcc-rtc";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&r_pio {
+	/* PL powers the PMIC bus itself; firmware must keep ALDO1 enabled. */
+	vcc-pm-supply = <&reg_aldo1>;
+};
+
+&rtc {
+	clocks = <&r_ccu CLK_BUS_R_RTC>, <&osc>, <&r_ccu CLK_R_AHB>,
+		 <&osc32k>;
+	clock-names = "bus", "hosc", "ahb", "ext-osc32k";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
-- 
2.43.0

[PATCH 3/3] arm64: dts: allwinner: sun60i-a733-cubie-a7z: add the user LED

[Vinicius Pedrosa]

Describe the green user LED on the Radxa Cubie A7Z. It is driven high
by PM2 and uses the heartbeat trigger by default.

Signed-off-by: Vinicius Pedrosa <vinicius.eduardo.pedrosa@gmail.com>
---
 .../boot/dts/allwinner/sun60i-a733-cubie-a7z.dts     | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7z.dts b/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7z.dts
index ab3d3d70f9ff..5dee2084906c 100644
--- a/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7z.dts
+++ b/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7z.dts
@@ -4,6 +4,7 @@
 #include "sun60i-a733.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	model = "Radxa Cubie A7Z";
@@ -18,6 +19,17 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
 	reg_ps: regulator-system-power {
 		compatible = "regulator-fixed";
 		regulator-name = "ps";
-- 
2.43.0