[PATCH 3/7] arm64: dts: qcom: lemans-draco-evk: Add DLC DLC0697 DSI panel overlay

[mohit.dsor@oss.qualcomm.com]

From: Vishnu Saini <vishnu.saini@oss.qualcomm.com>

Add a DT overlay to enable DLC0697 panel when DLC daughter card is
connected to DSI0_B2B on carrier card.

The card plugs into the display B2B connector shared with the LT9611UXD
HDMI bridge, so the bridge and HDMI connector are disabled when this
overlay is applied. DSI0 must be routed to the B2B connector with
DIPSW2.4 set to ON.

Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
Signed-off-by: Mohit Dsor <mohit.dsor@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  4 ++
 .../dts/qcom/lemans-draco-evk-dlc0697-dsi.dtso     | 81 ++++++++++++++++++++++
 2 files changed, 85 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 3262604ffb05..90a00ab40c1a 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -61,6 +61,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= lemans-draco-evk.dtb
 lemans-draco-evk-hdmi-dual-dsi-dtbs := lemans-draco-evk.dtb lemans-draco-evk-hdmi-dual-dsi.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= lemans-draco-evk-hdmi-dual-dsi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= lemans-draco-evk-hdmi-dual-dsi.dtbo
+
+lemans-draco-evk-dlc0697-dsi-dtbs := lemans-draco-evk.dtb lemans-draco-evk-dlc0697-dsi.dtbo
+dtb-$(CONFIG_ARCH_QCOM)	+= lemans-draco-evk-dlc0697-dsi.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= lemans-draco-evk-dlc0697-dsi.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= mahua-crd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= milos-fairphone-fp6.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= milos-nothing-asteroids.dtb
diff --git a/arch/arm64/boot/dts/qcom/lemans-draco-evk-dlc0697-dsi.dtso b/arch/arm64/boot/dts/qcom/lemans-draco-evk-dlc0697-dsi.dtso
new file mode 100644
index 000000000000..00845b6207a4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/lemans-draco-evk-dlc0697-dsi.dtso
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+&{/} {
+	dlc_backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&expander2 2 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+};
+
+&hdmi_bridge {
+	status = "disabled";
+};
+
+&hdmi_connector {
+	status = "disabled";
+};
+
+&mdss0_dsi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "dlc,dlc0697", "ilitek,ili7807s";
+		reg = <0>;
+
+		avdd-supply = <&vreg_bridge_3p3>;
+		avee-supply = <&vreg_bridge_3p3>;
+		backlight = <&dlc_backlight>;
+		pinctrl-0 = <&panel_rst_n &panel_te_pin>;
+		pinctrl-1 = <&panel_rst_n_suspend>;
+		pinctrl-names = "default", "sleep";
+		reset-gpios = <&pmm8654au_1_gpios 4 GPIO_ACTIVE_LOW>;
+		vddi-supply = <&vreg_s4a>;
+
+		port {
+			dlc_panel_in: endpoint {
+				remote-endpoint = <&mdss0_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss0_dsi0_out {
+	remote-endpoint = <&dlc_panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&pmm8654au_1_gpios {
+	panel_rst_n: panel-rst-n-state {
+		pins = "gpio4";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
+		bias-disable;
+	};
+
+	panel_rst_n_suspend: panel-rst-n-suspend-state {
+		pins = "gpio4";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+		bias-pull-down;
+	};
+};
+
+&tlmm {
+	panel_te_pin: panel-te-pin-state {
+		pins = "gpio84";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};

-- 
2.34.1