* [PATCH v4 2/2] gpio: Add Cortina Systems CS75xx GPIO driver
2026-11-16 2:08 [PATCH v4 0/2] gpio: Add Cortina Systems CS75xx GPIO driver Fil Dunsky via B4 Relay
2026-11-16 2:08 ` [PATCH v4 1/2] dt-bindings: gpio: Add Cortina Systems CS7542 GPIO controller Fil Dunsky via B4 Relay
@ 2026-11-16 2:08 ` Fil Dunsky via B4 Relay
1 sibling, 0 replies; 3+ messages in thread
From: Fil Dunsky via B4 Relay @ 2026-11-16 2:08 UTC (permalink / raw)
To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-gpio, devicetree, linux-kernel, linux-arm-kernel, Fil Dunsky
From: Fil Dunsky <filipp.dunsky@gmail.com>
Add a driver for the GPIO banks of the Cortina Systems CS75xx SoCs. The
data and direction registers are handled by gpio-mmio; each bank has its
own interrupt with level and edge triggers, both edges are emulated by
flipping the polarity.
A pin only works as a GPIO when the pin mux in the global control block
selects the GPIO function. That is not part of the GPIO controller and
is left to the boot loader until there is a pin controller driver.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
---
drivers/gpio/Kconfig | 12 ++
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-cs75xx.c | 281 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 294 insertions(+)
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 55e428002..cc00cfe48 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -300,6 +300,18 @@ config GPIO_CLPS711X
help
Say yes here to support GPIO on CLPS711X SoCs.
+config GPIO_CS75XX
+ tristate "Cortina Systems CS75xx GPIO support"
+ depends on ARCH_CORTINA_ACCESS || COMPILE_TEST
+ select GPIO_GENERIC
+ select GPIOLIB_IRQCHIP
+ help
+ Say yes here to support the GPIO banks of the Cortina Systems
+ CS75xx SoCs, including their interrupts.
+
+ This driver can also be built as a module. If so, the module
+ will be called gpio-cs75xx.
+
config GPIO_DAVINCI
tristate "TI Davinci/Keystone GPIO support"
default y if ARCH_DAVINCI
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 88f748846..2c2e18ef2 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -60,6 +60,7 @@ obj-$(CONFIG_GPIO_SNPS_CREG) += gpio-creg-snps.o
obj-$(CONFIG_GPIO_CROS_EC) += gpio-cros-ec.o
obj-$(CONFIG_GPIO_CRYSTAL_COVE) += gpio-crystalcove.o
obj-$(CONFIG_GPIO_CS5535) += gpio-cs5535.o
+obj-$(CONFIG_GPIO_CS75XX) += gpio-cs75xx.o
obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o
obj-$(CONFIG_GPIO_DA9055) += gpio-da9055.o
obj-$(CONFIG_GPIO_DAVINCI) += gpio-davinci.o
diff --git a/drivers/gpio/gpio-cs75xx.c b/drivers/gpio/gpio-cs75xx.c
new file mode 100644
index 000000000..b4f288910
--- /dev/null
+++ b/drivers/gpio/gpio-cs75xx.c
@@ -0,0 +1,281 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Cortina Systems CS75xx GPIO controller
+ *
+ * Each bank has 32 lines with direction, data and interrupt registers.
+ * Whether a pin is driven by the GPIO bank or by its peripheral function
+ * (NAND, Ethernet, UART, ...) is selected in the global control block,
+ * which this driver does not touch: the pin mux is left as the boot loader
+ * set it up.
+ */
+
+#include <linux/bitops.h>
+#include <linux/cleanup.h>
+#include <linux/gpio/driver.h>
+#include <linux/gpio/generic.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define CS75XX_GPIO_CFG 0x00 /* 1: input, 0: output */
+#define CS75XX_GPIO_OUT 0x04
+#define CS75XX_GPIO_IN 0x08
+#define CS75XX_GPIO_LVL 0x0c /* 1: high level or rising edge */
+#define CS75XX_GPIO_EDGE 0x10 /* 1: edge, 0: level */
+#define CS75XX_GPIO_IE 0x14
+#define CS75XX_GPIO_INT 0x18 /* write 1 to clear */
+
+struct cs75xx_gpio {
+ struct gpio_generic_chip chip;
+ void __iomem *base;
+ u32 both_edges;
+};
+
+/* Both edges are emulated by flipping the polarity on every interrupt */
+static void cs75xx_gpio_set_polarity(struct cs75xx_gpio *g, u32 mask)
+{
+ u32 lvl = readl(g->base + CS75XX_GPIO_LVL);
+
+ if (readl(g->base + CS75XX_GPIO_IN) & mask)
+ lvl &= ~mask;
+ else
+ lvl |= mask;
+
+ writel(lvl, g->base + CS75XX_GPIO_LVL);
+}
+
+static void cs75xx_gpio_irq_ack(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct cs75xx_gpio *g = gpiochip_get_data(gc);
+ u32 mask = BIT(irqd_to_hwirq(d));
+
+ guard(gpio_generic_lock_irqsave)(&g->chip);
+ writel(mask, g->base + CS75XX_GPIO_INT);
+ /* Arm the opposite edge after the ack, so that it is not lost */
+ if (g->both_edges & mask)
+ cs75xx_gpio_set_polarity(g, mask);
+}
+
+static void cs75xx_gpio_irq_mask(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct cs75xx_gpio *g = gpiochip_get_data(gc);
+ irq_hw_number_t hwirq = irqd_to_hwirq(d);
+
+ scoped_guard(gpio_generic_lock_irqsave, &g->chip) {
+ u32 ie = readl(g->base + CS75XX_GPIO_IE);
+
+ writel(ie & ~BIT(hwirq), g->base + CS75XX_GPIO_IE);
+ }
+
+ gpiochip_disable_irq(gc, hwirq);
+}
+
+static void cs75xx_gpio_irq_unmask(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct cs75xx_gpio *g = gpiochip_get_data(gc);
+ irq_hw_number_t hwirq = irqd_to_hwirq(d);
+ u32 ie;
+
+ gpiochip_enable_irq(gc, hwirq);
+
+ guard(gpio_generic_lock_irqsave)(&g->chip);
+ /*
+ * The status of a level interrupt is latched while the line is
+ * asserted, also after the ack, so it may be stale by now. Clear it,
+ * it is set again right away if the line is still asserted.
+ */
+ if (irqd_is_level_type(d))
+ writel(BIT(hwirq), g->base + CS75XX_GPIO_INT);
+ ie = readl(g->base + CS75XX_GPIO_IE);
+ writel(ie | BIT(hwirq), g->base + CS75XX_GPIO_IE);
+}
+
+static int cs75xx_gpio_irq_set_type(struct irq_data *d, unsigned int type)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct cs75xx_gpio *g = gpiochip_get_data(gc);
+ u32 mask = BIT(irqd_to_hwirq(d));
+ u32 lvl, edge, both_edges;
+
+ guard(gpio_generic_lock_irqsave)(&g->chip);
+
+ lvl = readl(g->base + CS75XX_GPIO_LVL);
+ edge = readl(g->base + CS75XX_GPIO_EDGE);
+ both_edges = g->both_edges & ~mask;
+
+ switch (type & IRQ_TYPE_SENSE_MASK) {
+ case IRQ_TYPE_LEVEL_LOW:
+ lvl &= ~mask;
+ edge &= ~mask;
+ break;
+ case IRQ_TYPE_LEVEL_HIGH:
+ lvl |= mask;
+ edge &= ~mask;
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ lvl &= ~mask;
+ edge |= mask;
+ break;
+ case IRQ_TYPE_EDGE_RISING:
+ lvl |= mask;
+ edge |= mask;
+ break;
+ case IRQ_TYPE_EDGE_BOTH:
+ both_edges |= mask;
+ edge |= mask;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ g->both_edges = both_edges;
+ writel(lvl, g->base + CS75XX_GPIO_LVL);
+ writel(edge, g->base + CS75XX_GPIO_EDGE);
+ if (g->both_edges & mask)
+ cs75xx_gpio_set_polarity(g, mask);
+
+ if (type & IRQ_TYPE_LEVEL_MASK)
+ irq_set_handler_locked(d, handle_level_irq);
+ else
+ irq_set_handler_locked(d, handle_edge_irq);
+
+ return 0;
+}
+
+static int cs75xx_gpio_irq_reqres(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ irq_hw_number_t hwirq = irqd_to_hwirq(d);
+ int ret;
+
+ /*
+ * The boot loader may leave the line configured as an output. Only
+ * touch it when nobody else has requested it.
+ */
+ char *label __free(kfree) = gpiochip_dup_line_label(gc, hwirq);
+ if (IS_ERR(label))
+ return PTR_ERR(label);
+ if (!label) {
+ ret = gc->direction_input(gc, hwirq);
+ if (ret)
+ return ret;
+ }
+
+ return gpiochip_reqres_irq(gc, hwirq);
+}
+
+static void cs75xx_gpio_irq_relres(struct irq_data *d)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+
+ gpiochip_relres_irq(gc, irqd_to_hwirq(d));
+}
+
+static const struct irq_chip cs75xx_gpio_irq_chip = {
+ .name = "cs75xx-gpio",
+ .irq_ack = cs75xx_gpio_irq_ack,
+ .irq_mask = cs75xx_gpio_irq_mask,
+ .irq_unmask = cs75xx_gpio_irq_unmask,
+ .irq_set_type = cs75xx_gpio_irq_set_type,
+ .irq_request_resources = cs75xx_gpio_irq_reqres,
+ .irq_release_resources = cs75xx_gpio_irq_relres,
+ .flags = IRQCHIP_IMMUTABLE | IRQCHIP_MASK_ON_SUSPEND,
+};
+
+static void cs75xx_gpio_irq_handler(struct irq_desc *desc)
+{
+ struct gpio_chip *gc = irq_desc_get_handler_data(desc);
+ struct cs75xx_gpio *g = gpiochip_get_data(gc);
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+ unsigned long pending;
+ unsigned int offset;
+
+ chained_irq_enter(chip, desc);
+
+ pending = readl(g->base + CS75XX_GPIO_INT) &
+ readl(g->base + CS75XX_GPIO_IE);
+
+ for_each_set_bit(offset, &pending, gc->ngpio)
+ generic_handle_domain_irq(gc->irq.domain, offset);
+
+ chained_irq_exit(chip, desc);
+}
+
+static int cs75xx_gpio_probe(struct platform_device *pdev)
+{
+ struct gpio_generic_chip_config config;
+ struct device *dev = &pdev->dev;
+ struct gpio_irq_chip *girq;
+ struct cs75xx_gpio *g;
+ int irq, ret;
+
+ g = devm_kzalloc(dev, sizeof(*g), GFP_KERNEL);
+ if (!g)
+ return -ENOMEM;
+
+ g->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(g->base))
+ return PTR_ERR(g->base);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ config = (struct gpio_generic_chip_config) {
+ .dev = dev,
+ .sz = 4,
+ .dat = g->base + CS75XX_GPIO_IN,
+ .set = g->base + CS75XX_GPIO_OUT,
+ .dirin = g->base + CS75XX_GPIO_CFG,
+ };
+
+ ret = gpio_generic_chip_init(&g->chip, &config);
+ if (ret)
+ return dev_err_probe(dev, ret, "unable to init generic GPIO\n");
+
+ if (g->chip.gc.ngpio > 32)
+ return dev_err_probe(dev, -EINVAL, "too many lines: %u\n",
+ g->chip.gc.ngpio);
+
+ /* Mask and clear all interrupts before the parent is set up */
+ writel(0, g->base + CS75XX_GPIO_IE);
+ writel(~0, g->base + CS75XX_GPIO_INT);
+
+ girq = &g->chip.gc.irq;
+ gpio_irq_chip_set_chip(girq, &cs75xx_gpio_irq_chip);
+ girq->parent_handler = cs75xx_gpio_irq_handler;
+ girq->num_parents = 1;
+ girq->parents = devm_kcalloc(dev, 1, sizeof(*girq->parents),
+ GFP_KERNEL);
+ if (!girq->parents)
+ return -ENOMEM;
+ girq->parents[0] = irq;
+ girq->default_type = IRQ_TYPE_NONE;
+ girq->handler = handle_bad_irq;
+
+ return devm_gpiochip_add_data(dev, &g->chip.gc, g);
+}
+
+static const struct of_device_id cs75xx_gpio_of_match[] = {
+ { .compatible = "cortina,cs7542-gpio" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, cs75xx_gpio_of_match);
+
+static struct platform_driver cs75xx_gpio_driver = {
+ .probe = cs75xx_gpio_probe,
+ .driver = {
+ .name = "cs75xx-gpio",
+ .of_match_table = cs75xx_gpio_of_match,
+ },
+};
+module_platform_driver(cs75xx_gpio_driver);
+
+MODULE_DESCRIPTION("Cortina Systems CS75xx GPIO driver");
+MODULE_LICENSE("GPL");
--
2.53.0
^ permalink raw reply [flat|nested] 3+ messages in thread