* [PATCH] usb: typec: tipd: cd321x: replay the plug on resume
@ 2026-11-12 11:30 Jacob Procee
2026-11-17 11:08 ` Heikki Krogerus
0 siblings, 1 reply; 5+ messages in thread
From: Jacob Procee @ 2026-11-12 11:30 UTC (permalink / raw)
To: Heikki Krogerus, Greg Kroah-Hartman
Cc: linux-usb, linux-kernel, Sven Peter, Janne Grunau, Jacob Procee
On Apple Silicon the Type-C PHY and the dwc3 controller behind a CD321x
port lose their state during s2idle while the plug stays connected, and
the CD321x does not raise an interrupt on resume. xhci notices the lost
state and re-initializes the host controller:
xhci-hcd xhci-hcd.0.auto: xHC error in resume, USBSTS 0x401, Reinit
usb usb1: root hub lost power or was reset
usb 1-1: USB disconnect, device number 2
but the PHY is only ever programmed from typec_mux_set(), so a device
left plugged in (here a FIDO2 security key) never comes back until it is
unplugged and plugged in again.
Re-initializing only dwc3 after resume does not work: tearing dwc3 down
also powers off the PHY, and nothing turns it back on, so xhci then
times out ("Host halt failed, -110", "can't setup: -110").
Instead, make cd321x replay the plug on resume when a partner was
connected: mark the plug as changed and queue the update work, which
then goes through the same sequence as a real replug (role none, mux
safe, mux back to the partner's mode, role back on). Queue it on
system_freezable_wq so it runs only after all devices have resumed.
Tested on a 14" MacBook Pro (M1 Pro, j314s) with a backport of this
change to the Asahi 7.3.3 kernel: a USB-C security key left plugged in
re-enumerates right after "PM: suspend exit", where it previously stayed
gone until replugged. Unplugging the device while the system is asleep
also works: after resume the role goes to none, nothing is brought back
up, and replugging it later enumerates normally. This mainline version
was build-tested only (W=1, checkpatch --strict clean).
Fixes: 82432bbfb9e8 ("usb: typec: tipd: Handle mode transitions for CD321x")
Assisted-by: LLM
Signed-off-by: Jacob Procee <sn125164@gmail.com>
---
checkpatch flags the Assisted-by tag (non-standard signature, 'LLM' is
not an email address); the format follows
Documentation/process/coding-assistants.rst.
drivers/usb/typec/tipd/core.c | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/drivers/usb/typec/tipd/core.c b/drivers/usb/typec/tipd/core.c
index 02539378ffed..2ec380124532 100644
--- a/drivers/usb/typec/tipd/core.c
+++ b/drivers/usb/typec/tipd/core.c
@@ -164,6 +164,7 @@ struct tipd_data {
bool (*read_power_status)(struct tps6598x *tps);
int (*reset)(struct tps6598x *tps);
int (*connect)(struct tps6598x *tps, u32 status);
+ void (*resume)(struct tps6598x *tps);
};
struct tps6598x {
@@ -911,6 +912,21 @@ static int cd321x_connect(struct tps6598x *tps, u32 status)
return 0;
}
+static void cd321x_resume(struct tps6598x *tps)
+{
+ struct cd321x *cd321x = container_of(tps, struct cd321x, tps);
+
+ guard(mutex)(&tps->lock);
+
+ if (IS_ERR_OR_NULL(tps->partner))
+ return;
+
+ cd321x->update_status.status_changed |= TPS_STATUS_PLUG_PRESENT;
+ cancel_delayed_work(&cd321x->update_work);
+ queue_delayed_work(system_freezable_wq, &cd321x->update_work,
+ msecs_to_jiffies(CD321X_DEBOUNCE_DELAY_MS));
+}
+
static irqreturn_t cd321x_interrupt(int irq, void *data)
{
struct tps6598x *tps = data;
@@ -2014,6 +2030,9 @@ static int __maybe_unused tps6598x_resume(struct device *dev)
queue_delayed_work(system_power_efficient_wq, &tps->wq_poll,
msecs_to_jiffies(POLL_INTERVAL));
+ if (tps->data->resume)
+ tps->data->resume(tps);
+
return 0;
}
@@ -2040,6 +2059,7 @@ static const struct tipd_data cd321x_data = {
.reset = cd321x_reset,
.switch_power_state = cd321x_switch_power_state,
.connect = cd321x_connect,
+ .resume = cd321x_resume,
};
static const struct tipd_data tps6598x_data = {
--
2.56.0
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [PATCH] usb: typec: tipd: cd321x: replay the plug on resume
2026-11-12 11:30 [PATCH] usb: typec: tipd: cd321x: replay the plug on resume Jacob Procee
@ 2026-11-17 11:08 ` Heikki Krogerus
2026-11-17 12:03 ` Sven Peter
0 siblings, 1 reply; 5+ messages in thread
From: Heikki Krogerus @ 2026-11-17 11:08 UTC (permalink / raw)
To: Jacob Procee, Sven Peter
Cc: Greg Kroah-Hartman, linux-usb, linux-kernel, Janne Grunau
On Thu, Nov 12, 2026 at 12:30:05PM +0100, Jacob Procee wrote:
> On Apple Silicon the Type-C PHY and the dwc3 controller behind a CD321x
> port lose their state during s2idle while the plug stays connected, and
> the CD321x does not raise an interrupt on resume. xhci notices the lost
> state and re-initializes the host controller:
>
> xhci-hcd xhci-hcd.0.auto: xHC error in resume, USBSTS 0x401, Reinit
> usb usb1: root hub lost power or was reset
> usb 1-1: USB disconnect, device number 2
>
> but the PHY is only ever programmed from typec_mux_set(), so a device
> left plugged in (here a FIDO2 security key) never comes back until it is
> unplugged and plugged in again.
>
> Re-initializing only dwc3 after resume does not work: tearing dwc3 down
> also powers off the PHY, and nothing turns it back on, so xhci then
> times out ("Host halt failed, -110", "can't setup: -110").
>
> Instead, make cd321x replay the plug on resume when a partner was
> connected: mark the plug as changed and queue the update work, which
> then goes through the same sequence as a real replug (role none, mux
> safe, mux back to the partner's mode, role back on). Queue it on
> system_freezable_wq so it runs only after all devices have resumed.
>
> Tested on a 14" MacBook Pro (M1 Pro, j314s) with a backport of this
> change to the Asahi 7.3.3 kernel: a USB-C security key left plugged in
> re-enumerates right after "PM: suspend exit", where it previously stayed
> gone until replugged. Unplugging the device while the system is asleep
> also works: after resume the role goes to none, nothing is brought back
> up, and replugging it later enumerates normally. This mainline version
> was build-tested only (W=1, checkpatch --strict clean).
>
> Fixes: 82432bbfb9e8 ("usb: typec: tipd: Handle mode transitions for CD321x")
> Assisted-by: LLM
> Signed-off-by: Jacob Procee <sn125164@gmail.com>
Looks okay to me, but as this is a fix, you should CC stable:
https://docs.kernel.org/process/submitting-patches.html#select-the-recipients-for-your-patch
Sven, would you be interested, or would you have time, to maintain
this driver?
Thanks,
> ---
> checkpatch flags the Assisted-by tag (non-standard signature, 'LLM' is
> not an email address); the format follows
> Documentation/process/coding-assistants.rst.
>
> drivers/usb/typec/tipd/core.c | 20 ++++++++++++++++++++
> 1 file changed, 20 insertions(+)
>
> diff --git a/drivers/usb/typec/tipd/core.c b/drivers/usb/typec/tipd/core.c
> index 02539378ffed..2ec380124532 100644
> --- a/drivers/usb/typec/tipd/core.c
> +++ b/drivers/usb/typec/tipd/core.c
> @@ -164,6 +164,7 @@ struct tipd_data {
> bool (*read_power_status)(struct tps6598x *tps);
> int (*reset)(struct tps6598x *tps);
> int (*connect)(struct tps6598x *tps, u32 status);
> + void (*resume)(struct tps6598x *tps);
> };
>
> struct tps6598x {
> @@ -911,6 +912,21 @@ static int cd321x_connect(struct tps6598x *tps, u32 status)
> return 0;
> }
>
> +static void cd321x_resume(struct tps6598x *tps)
> +{
> + struct cd321x *cd321x = container_of(tps, struct cd321x, tps);
> +
> + guard(mutex)(&tps->lock);
> +
> + if (IS_ERR_OR_NULL(tps->partner))
> + return;
> +
> + cd321x->update_status.status_changed |= TPS_STATUS_PLUG_PRESENT;
> + cancel_delayed_work(&cd321x->update_work);
> + queue_delayed_work(system_freezable_wq, &cd321x->update_work,
> + msecs_to_jiffies(CD321X_DEBOUNCE_DELAY_MS));
> +}
> +
> static irqreturn_t cd321x_interrupt(int irq, void *data)
> {
> struct tps6598x *tps = data;
> @@ -2014,6 +2030,9 @@ static int __maybe_unused tps6598x_resume(struct device *dev)
> queue_delayed_work(system_power_efficient_wq, &tps->wq_poll,
> msecs_to_jiffies(POLL_INTERVAL));
>
> + if (tps->data->resume)
> + tps->data->resume(tps);
> +
> return 0;
> }
>
> @@ -2040,6 +2059,7 @@ static const struct tipd_data cd321x_data = {
> .reset = cd321x_reset,
> .switch_power_state = cd321x_switch_power_state,
> .connect = cd321x_connect,
> + .resume = cd321x_resume,
> };
>
> static const struct tipd_data tps6598x_data = {
> --
> 2.56.0
--
heikki
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [PATCH] usb: typec: tipd: cd321x: replay the plug on resume
2026-11-17 11:08 ` Heikki Krogerus
@ 2026-11-17 12:03 ` Sven Peter
2026-11-17 12:17 ` Jacob Procee
0 siblings, 1 reply; 5+ messages in thread
From: Sven Peter @ 2026-11-17 12:03 UTC (permalink / raw)
To: Heikki Krogerus, Jacob Procee
Cc: Greg Kroah-Hartman, linux-usb, linux-kernel, Janne Grunau
On 17.11.26 12:08, Heikki Krogerus wrote:
> On Thu, Nov 12, 2026 at 12:30:05PM +0100, Jacob Procee wrote:
>> On Apple Silicon the Type-C PHY and the dwc3 controller behind a CD321x
>> port lose their state during s2idle while the plug stays connected, and
>> the CD321x does not raise an interrupt on resume. xhci notices the lost
>> state and re-initializes the host controller:
>>
>> xhci-hcd xhci-hcd.0.auto: xHC error in resume, USBSTS 0x401, Reinit
>> usb usb1: root hub lost power or was reset
>> usb 1-1: USB disconnect, device number 2
>>
>> but the PHY is only ever programmed from typec_mux_set(), so a device
>> left plugged in (here a FIDO2 security key) never comes back until it is
>> unplugged and plugged in again.
>>
>> Re-initializing only dwc3 after resume does not work: tearing dwc3 down
>> also powers off the PHY, and nothing turns it back on, so xhci then
>> times out ("Host halt failed, -110", "can't setup: -110").
>>
>> Instead, make cd321x replay the plug on resume when a partner was
>> connected: mark the plug as changed and queue the update work, which
>> then goes through the same sequence as a real replug (role none, mux
>> safe, mux back to the partner's mode, role back on). Queue it on
>> system_freezable_wq so it runs only after all devices have resumed.
>>
>> Tested on a 14" MacBook Pro (M1 Pro, j314s) with a backport of this
>> change to the Asahi 7.3.3 kernel: a USB-C security key left plugged in
>> re-enumerates right after "PM: suspend exit", where it previously stayed
>> gone until replugged. Unplugging the device while the system is asleep
>> also works: after resume the role goes to none, nothing is brought back
>> up, and replugging it later enumerates normally. This mainline version
>> was build-tested only (W=1, checkpatch --strict clean).
>>
>> Fixes: 82432bbfb9e8 ("usb: typec: tipd: Handle mode transitions for CD321x")
>> Assisted-by: LLM
>> Signed-off-by: Jacob Procee <sn125164@gmail.com>
>
> Looks okay to me, but as this is a fix, you should CC stable:
> https://docs.kernel.org/process/submitting-patches.html#select-the-recipients-for-your-patch
So I really don't think it's a good idea to work around a symptom here
and effectively fake a unplug/plug on each suspend.
XHCI is already capable of putting individual ports into a low power
state and it should already try to do that during suspend. Resume just
doesn't seem to work correctly for some reason on this platform.
I suspect we're just missing the proper suspend/resume work in the PHY
itself to put it into a low power state. Or maybe we need to keep an
additional power domain enabled so that the PHY doesn't lose all state
and keeps working in a lower power mode.
When using XNU it's possible to wake the machine with e.g. a usb
keyboard and it doesn't re-enumerate everything on resume and that
should be possible here on Linux as well. And I really don't think
that's going to be more complex than this patch here.
>
> Sven, would you be interested, or would you have time, to maintain
> this driver?
Sure, I can help.
Thanks,
Sven
^ permalink raw reply [flat|nested] 5+ messages in thread* Re: [PATCH] usb: typec: tipd: cd321x: replay the plug on resume
2026-11-17 12:03 ` Sven Peter
@ 2026-11-17 12:17 ` Jacob Procee
2026-11-17 12:47 ` Janne Grunau
0 siblings, 1 reply; 5+ messages in thread
From: Jacob Procee @ 2026-11-17 12:17 UTC (permalink / raw)
To: Sven Peter
Cc: Heikki Krogerus, Greg Kroah-Hartman, linux-usb, linux-kernel,
Janne Grunau
On Tue, 17 Nov 2026 13:03:03 +0100
Sven Peter <sven@kernel.org> wrote:
> I suspect we're just missing the proper suspend/resume work in the PHY
> itself to put it into a low power state. Or maybe we need to keep an
> additional power domain enabled so that the PHY doesn't lose all state
> and keeps working in a lower power mode.
Agreed, please drop this (and v2).
That second option is what happens with wakeup enabled: the dwc3 node
and the ATC PHY share the atc*_usb pmgr domain, and it's only switched
off in s2idle because xhci and the root hubs default to power/wakeup =
disabled. With wakeup enabled on xhci-hcd.*.auto and usb* (Asahi 7.3.3,
j314s), the domain stays on and a device left plugged in stays
connected through s2idle without re-enumerating (no "xHC error in
resume ... Reinit"). Asahi's pmgr marks these domains
GENPD_FLAG_ACTIVE_WAKEUP; mainline's doesn't yet.
Wake from a USB keyboard still doesn't work: nothing calls
enable_irq_wake() for the dwc3/xhci IRQ, and irq-apple-aic has neither
irq_set_wake nor IRQCHIP_SKIP_SET_WAKE.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH] usb: typec: tipd: cd321x: replay the plug on resume
2026-11-17 12:17 ` Jacob Procee
@ 2026-11-17 12:47 ` Janne Grunau
0 siblings, 0 replies; 5+ messages in thread
From: Janne Grunau @ 2026-11-17 12:47 UTC (permalink / raw)
To: Jacob Procee
Cc: Sven Peter, Heikki Krogerus, Greg Kroah-Hartman, linux-usb, linux-kernel
On Tue, Nov 17, 2026 at 01:17:13PM +0100, Jacob Procee wrote:
> On Tue, 17 Nov 2026 13:03:03 +0100
> Sven Peter <sven@kernel.org> wrote:
>
> > I suspect we're just missing the proper suspend/resume work in the PHY
> > itself to put it into a low power state. Or maybe we need to keep an
> > additional power domain enabled so that the PHY doesn't lose all state
> > and keeps working in a lower power mode.
>
> Agreed, please drop this (and v2).
>
> That second option is what happens with wakeup enabled: the dwc3 node
> and the ATC PHY share the atc*_usb pmgr domain, and it's only switched
> off in s2idle because xhci and the root hubs default to power/wakeup =
> disabled. With wakeup enabled on xhci-hcd.*.auto and usb* (Asahi 7.3.3,
> j314s), the domain stays on and a device left plugged in stays
> connected through s2idle without re-enumerating (no "xHC error in
> resume ... Reinit"). Asahi's pmgr marks these domains
> GENPD_FLAG_ACTIVE_WAKEUP; mainline's doesn't yet.
yes, the downstream tree has commit to set GENPD_FLAG_ACTIVE_WAKEUP for
all power-domains which are active at probe (boot) time.
> Wake from a USB keyboard still doesn't work: nothing calls
> enable_irq_wake() for the dwc3/xhci IRQ, and irq-apple-aic has neither
> irq_set_wake nor IRQCHIP_SKIP_SET_WAKE.
The interrupt controller (AIC) doesn't have functionality to configure
IRQs as wake up source so it should set IRQCHIP_SKIP_SET_WAKE. Does wake
from USB keyboard work with that changed?
You might also need to add "wakeup-source" to the dwc3 nodes.
Janne
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2026-11-17 12:47 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-11-12 11:30 [PATCH] usb: typec: tipd: cd321x: replay the plug on resume Jacob Procee
2026-11-17 11:08 ` Heikki Krogerus
2026-11-17 12:03 ` Sven Peter
2026-11-17 12:17 ` Jacob Procee
2026-11-17 12:47 ` Janne Grunau
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®