From: Mattijs Korpershoek <mkorpershoek@kernel.org>
To: Hans Verkuil <hverkuil+cisco@kernel.org>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
Kieran Bingham <kieran.bingham@ideasonboard.com>,
Sakari Ailus <sakari.ailus@linux.intel.com>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
Andy Walls <awalls@md.metrocast.net>,
Kees Cook <kees@kernel.org>,
"Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Mattijs Korpershoek <mkorpershoek@kernel.org>,
Nicolas Dufresne <nicolas.dufres@collabora.com>,
Hans de Goede <hansg@kernel.org>,
Michael Riesch <michael.riesch@collabora.com>,
Dave Stevenson <dave.stevenson@raspberrypi.com>,
Maxime Ripard <mripard@kernel.org>,
linux-media@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-hardening@vger.kernel.org
Subject: [PATCH RFC v2 15/16] media: imx219: Allow driver probe with missing sensor
Date: Wed, 18 Nov 2026 13:43:59 +0100 [thread overview]
Message-ID: <20261118-v4l2-sensor-detect-v2-15-1bb1a445b556@kernel.org> (raw)
In-Reply-To: <20261118-v4l2-sensor-detect-v2-0-1bb1a445b556@kernel.org>
When media fault tolerance is enabled, probe() should complete even when
a sensor is disconnected.
Currently, the driver reads the CHIP_ID over i2c in the probe().
When we can't read CHIP_ID, the probe errors out, which result in the
v4l2-subdev not being created.
Extract imx219_read_chip_id() from imx219_identify_module() so that
probe can distinguish an unreachable sensor (I2C read failure) from a
wrong sensor (CHIP_ID mismatch).
When the sensor is unreachable, skip the LP-11 state initialization and
continue probe so the v4l2-subdev and media entity are created.
Note that a CHIP_ID mismatch remains a fatal error.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
---
drivers/media/i2c/imx219.c | 74 ++++++++++++++++++++++------------------------
1 file changed, 36 insertions(+), 38 deletions(-)
diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
index 1580562093e8..02d065fb88d0 100644
--- a/drivers/media/i2c/imx219.c
+++ b/drivers/media/i2c/imx219.c
@@ -1099,25 +1099,9 @@ static int imx219_get_regulators(struct imx219 *imx219)
imx219->supplies);
}
-/* Verify chip ID */
-static int imx219_identify_module(struct imx219 *imx219)
+static int imx219_read_chip_id(struct imx219 *imx219, u64 *chip_id)
{
- struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
- int ret;
- u64 val;
-
- ret = cci_read(imx219->regmap, IMX219_REG_CHIP_ID, &val, NULL);
- if (ret)
- return dev_err_probe(&client->dev, ret,
- "failed to read chip id %x\n",
- IMX219_CHIP_ID);
-
- if (val != IMX219_CHIP_ID)
- return dev_err_probe(&client->dev, -EIO,
- "chip id mismatch: %x!=%llx\n",
- IMX219_CHIP_ID, val);
-
- return 0;
+ return cci_read(imx219->regmap, IMX219_REG_CHIP_ID, chip_id, NULL);
}
static int imx219_check_hwcfg(struct device *dev, struct imx219 *imx219)
@@ -1194,6 +1178,7 @@ static int imx219_probe(struct i2c_client *client)
struct device *dev = &client->dev;
struct imx219 *imx219;
int ret;
+ u64 val;
imx219 = devm_kzalloc(&client->dev, sizeof(*imx219), GFP_KERNEL);
if (!imx219)
@@ -1235,36 +1220,49 @@ static int imx219_probe(struct i2c_client *client)
"failed to get reset gpio\n");
/*
- * The sensor must be powered for imx219_identify_module()
+ * The sensor must be powered for imx219_read_chip_id()
* to be able to read the CHIP_ID register
*/
ret = imx219_power_on(dev);
if (ret)
return ret;
- ret = imx219_identify_module(imx219);
- if (ret)
- goto error_power_off;
-
- /*
- * Sensor doesn't enter LP-11 state upon power up until and unless
- * streaming is started, so upon power up switch the modes to:
- * streaming -> standby
- */
- ret = cci_write(imx219->regmap, IMX219_REG_MODE_SELECT,
- IMX219_MODE_STREAMING, NULL);
- if (ret < 0)
+ /* Verify chip ID */
+ ret = imx219_read_chip_id(imx219, &val);
+ if (ret) {
+ if (!media_fault_tolerance_enabled()) {
+ dev_err_probe(&client->dev, ret,
+ "failed to read chip id %x\n",
+ IMX219_CHIP_ID);
+ goto error_power_off;
+ }
+ dev_dbg(&client->dev, "failed to read chip id %x\n", IMX219_CHIP_ID);
+ } else if (val != IMX219_CHIP_ID) {
+ ret = dev_err_probe(&client->dev, -EIO,
+ "chip id mismatch: %x!=%llx\n",
+ IMX219_CHIP_ID, val);
goto error_power_off;
+ } else {
+ /*
+ * Sensor doesn't enter LP-11 state upon power up until and unless
+ * streaming is started, so upon power up switch the modes to:
+ * streaming -> standby
+ */
+ ret = cci_write(imx219->regmap, IMX219_REG_MODE_SELECT,
+ IMX219_MODE_STREAMING, NULL);
+ if (ret < 0)
+ goto error_power_off;
- usleep_range(100, 110);
+ usleep_range(100, 110);
- /* put sensor back to standby mode */
- ret = cci_write(imx219->regmap, IMX219_REG_MODE_SELECT,
- IMX219_MODE_STANDBY, NULL);
- if (ret < 0)
- goto error_power_off;
+ /* put sensor back to standby mode */
+ ret = cci_write(imx219->regmap, IMX219_REG_MODE_SELECT,
+ IMX219_MODE_STANDBY, NULL);
+ if (ret < 0)
+ goto error_power_off;
- usleep_range(100, 110);
+ usleep_range(100, 110);
+ }
ret = imx219_init_controls(imx219);
if (ret)
--
2.56.0
next prev parent reply other threads:[~2026-11-18 12:44 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-18 12:43 [PATCH RFC v2 00/16] media: Fault-Tolerant V4L2 Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 01/16] media: mc: Add struct media_device_fh pointer to media device IOCTL op Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 02/16] media: mc: Add per-file-handle data support Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 03/16] v4l: event: Separate event related information from struct v4l2_fh Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 04/16] v4l: event: Rework data structures for separating events and V4L2 Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 05/16] v4l: event: Split the event framework into generic and V4L2 bits Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 06/16] media: mc: Maintain a list of open file handles in a media device Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 07/16] media: mc: Add MEDIA_IOC_DQEVENT Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 08/16] media: mc: Add MEDIA_EVENT_ENTITY_REGISTRATION Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 09/16] Documentation: media: Add Media controller event documentation Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 10/16] media: media.h: Add entity connection status Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 11/16] media: mc: Add .detect() to media_entity_operations Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 12/16] media: mc: Add MEDIA_IOC_G_ENTITY_STATUS ioctl Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 13/16] media: mc: Add MEDIA_EVENT_ENTITY_STATUS_CHANGE event Mattijs Korpershoek
2026-11-18 12:43 ` [PATCH RFC v2 14/16] media: mc: Add detect polling helpers for drivers Mattijs Korpershoek
2026-11-18 12:43 ` Mattijs Korpershoek [this message]
2026-11-18 12:44 ` [PATCH RFC v2 16/16] media: imx219: Implement .detect() sensor operation Mattijs Korpershoek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261118-v4l2-sensor-detect-v2-15-1bb1a445b556@kernel.org \
--to=mkorpershoek@kernel.org \
--cc=awalls@md.metrocast.net \
--cc=dave.stevenson@raspberrypi.com \
--cc=gustavoars@kernel.org \
--cc=hansg@kernel.org \
--cc=hverkuil+cisco@kernel.org \
--cc=kees@kernel.org \
--cc=kieran.bingham@ideasonboard.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-hardening@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=michael.riesch@collabora.com \
--cc=mripard@kernel.org \
--cc=nicolas.dufres@collabora.com \
--cc=sakari.ailus@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®