* [PATCH v2 0/3] media: i2c: ov5693: Fix mode changes, flips and autosuspend
@ 2026-10-29 9:27 Marco Ziliani
2026-10-29 9:27 ` [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start Marco Ziliani
` (2 more replies)
0 siblings, 3 replies; 8+ messages in thread
From: Marco Ziliani @ 2026-10-29 9:27 UTC (permalink / raw)
To: Daniel Scally, Sakari Ailus, Mauro Carvalho Chehab
Cc: linux-media, Chris Simpson, Tony Garcia, Simon Kruse, D. Manresa,
linux-kernel, Marco Ziliani
Three fixes for the ov5693, found while getting the front camera of the
Microsoft Surface Pro 5 (IPU3) to work, and since tested on IPU6 and
IPU4P Surfaces as well.
Patch 1 programs the mode registers on every stream start instead of
on runtime PM resume, so that a format change also reaches a sensor
that stays powered between streams. This is the ov5693 counterpart of
commit 4e1446ac169a ("media: i2c: ov8865: Program the sensor on stream
start").
Patch 2 keeps the reported SBGGR10 order when a single flip is enabled
at full resolution: each flip moves the Bayer phase by one column, so
the output window is shifted by one column when hflip XOR vflip.
Patch 3 drops the usage count at stream stop with
pm_runtime_put_autosuspend(), so that the autosuspend delay counts from
stream stop rather than from the last resume.
Patch 1 has been public and in testing in the linux-surface tree since
2026-10-23 [2]. Simon Kruse's active state conversion [1] made the same
change as part of a larger rework; he has since dropped it from his
patch and will rebase the conversion on top of this series.
Patches 1 and 2 were developed in the linux-surface tree and tested
there on a Surface Pro 5 (IPU3), a Surface Pro 7 (IPU4P) and a Surface
Pro 7+ and Pro 9 (IPU6); patch 3 follows a report by Dario Manresa in
the same thread [2]. The three patches as posted here have also been
run on a Surface Pro 7 (IPU4P) and a Surface Pro 9 (IPU6) there.
[1] https://lore.kernel.org/linux-media/20261027074933.21921-1-simon0x+git@proton.me/
[2] https://github.com/linux-surface/kernel/pull/181
Signed-off-by: Marco Ziliani <rylos78@gmail.com>
---
Changes in v2:
- Patch 1: move ov5693_mode_configure() from ov5693_sensor_init() to
ov5693_s_stream() rather than calling it in both, and shorten the
commit message (Dan)
- Patch 1: Tested-by tags not carried over, since the code changed
- Patch 2: unchanged; whether to shift the window or to use
V4L2_CTRL_FLAG_MODIFY_LAYOUT is still being discussed on v1, happy
to switch if that is preferred (Dan)
- Patches 2 and 3: collected Reviewed-by and Tested-by tags
- Retested the series on the Surface Pro 5 (IPU3)
- Link to v1: https://patch.msgid.link/20261027-ov5693-fixes-v1-0-3c8ab1ae104d@gmail.com
---
Marco Ziliani (3):
media: i2c: ov5693: Program the mode registers on stream start
media: i2c: ov5693: Keep the Bayer order when flipping at full resolution
media: i2c: ov5693: Use autosuspend when stopping the stream
drivers/media/i2c/ov5693.c | 76 +++++++++++++++++++++++++++++++++++++---------
1 file changed, 62 insertions(+), 14 deletions(-)
---
base-commit: d7e7bca7169873b46e857c025c10f3336c1258d8
change-id: 20261027-ov5693-fixes-8ec29752893a
Best regards,
--
Marco Ziliani <rylos78@gmail.com>
^ permalink raw reply [flat|nested] 8+ messages in thread* [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start 2026-10-29 9:27 [PATCH v2 0/3] media: i2c: ov5693: Fix mode changes, flips and autosuspend Marco Ziliani @ 2026-10-29 9:27 ` Marco Ziliani 2026-10-29 16:56 ` Chris Simpson ` (2 more replies) 2026-10-29 9:27 ` [PATCH v2 2/3] media: i2c: ov5693: Keep the Bayer order when flipping at full resolution Marco Ziliani 2026-10-29 9:27 ` [PATCH v2 3/3] media: i2c: ov5693: Use autosuspend when stopping the stream Marco Ziliani 2 siblings, 3 replies; 8+ messages in thread From: Marco Ziliani @ 2026-10-29 9:27 UTC (permalink / raw) To: Daniel Scally, Sakari Ailus, Mauro Carvalho Chehab Cc: linux-media, Chris Simpson, Tony Garcia, Simon Kruse, D. Manresa, linux-kernel, Marco Ziliani ov5693_mode_configure() is only called from the runtime PM resume path, through ov5693_sensor_init(). If the sensor stays powered between two streams with different modes, the settings for the second mode are never written to the hardware. Move the call from ov5693_sensor_init() to ov5693_s_stream(), before the controls are applied, so that the mode is written on every stream start. Fixes: 89aef879cb53 ("media: i2c: Add support for ov5693 sensor") Link: https://github.com/linux-surface/kernel/pull/181 Signed-off-by: Marco Ziliani <rylos78@gmail.com> --- drivers/media/i2c/ov5693.c | 18 +++++++++++++----- 1 file changed, 13 insertions(+), 5 deletions(-) diff --git a/drivers/media/i2c/ov5693.c b/drivers/media/i2c/ov5693.c index 56599f9ca..d09095c3e 100644 --- a/drivers/media/i2c/ov5693.c +++ b/drivers/media/i2c/ov5693.c @@ -663,11 +663,6 @@ static int ov5693_sensor_init(struct ov5693_device *ov5693) return dev_err_probe(ov5693->dev, ret, "global settings error\n"); - ret = ov5693_mode_configure(ov5693); - if (ret) - return dev_err_probe(ov5693->dev, ret, - "mode configure error\n"); - ret = ov5693_enable_streaming(ov5693, false); if (ret) dev_err(ov5693->dev, "stop streaming error\n"); @@ -1000,6 +995,19 @@ static int ov5693_s_stream(struct v4l2_subdev *sd, int enable) return ret; mutex_lock(&ov5693->lock); + + /* + * Program the mode on every stream start, so that a format + * change also reaches a sensor that stayed powered since the + * previous stream, and before the controls so that the mode + * registers don't clobber them. + */ + ret = ov5693_mode_configure(ov5693); + if (ret) { + mutex_unlock(&ov5693->lock); + goto err_power_down; + } + ret = __v4l2_ctrl_handler_setup(&ov5693->ctrls.handler); if (ret) { mutex_unlock(&ov5693->lock); -- 2.56.0 ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start 2026-10-29 9:27 ` [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start Marco Ziliani @ 2026-10-29 16:56 ` Chris Simpson 2026-11-03 21:01 ` technosf 2026-11-20 9:37 ` Sakari Ailus 2 siblings, 0 replies; 8+ messages in thread From: Chris Simpson @ 2026-10-29 16:56 UTC (permalink / raw) To: Marco Ziliani, Daniel Scally, Sakari Ailus, Mauro Carvalho Chehab Cc: linux-media, Tony Garcia, Simon Kruse, D. Manresa, linux-kernel Tested on a Surface Pro 9 (Intel Alder Lake-U, i7-1255U; IPU6, front OV5693) in a 7.3-based kernel, with the v2 series applied to an ov5693.c that matches the base-commit (d7e7bca71698) apart from the pad ops' client_info argument, against the same file unpatched, using raw captures from the ISYS video node: - With the sensor held powered between streams, OUTPUT_SIZE (read over I2C during and after each stream) matched the requested size in 32 of 32 streams requesting 2592x1944 or 1296x972, and every stream delivered image data. Unpatched, it stayed at 2592x1944 in all 32 and the 1296x972 streams gave no frames. - With each stream started from runtime suspend, the path v2 changed, OUTPUT_SIZE matched the requested size in 12 of 12 streams (as it did unpatched), all with complete image data. The test scripts, the analysis of their output and this summary were prepared with an AI coding assistant (Claude); I ran the tests on my Surface Pro 9. Tested-by: Chris Simpson <chris@nilk.net> ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start 2026-10-29 9:27 ` [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start Marco Ziliani 2026-10-29 16:56 ` Chris Simpson @ 2026-11-03 21:01 ` technosf 2026-11-20 9:37 ` Sakari Ailus 2 siblings, 0 replies; 8+ messages in thread From: technosf @ 2026-11-03 21:01 UTC (permalink / raw) To: Marco Ziliani, Daniel Scally, Sakari Ailus, Mauro Carvalho Chehab Cc: linux-media, Chris Simpson, Tony Garcia, Simon Kruse, D. Manresa, linux-kernel Tested on a Surface Pro 8 (Intel Tiger Lake, IPU6; front OV5693, ACPI HID INT33BE) in a 7.2.14-based linux-surface kernel, with patch 1/3 of the v2 series applied to ov5693.c. The tree also carries linux-surface/kernel#180 (MIPI clock lane gating), loaded with clock_ncont=1; that is not in mainline and is needed for the sensor to stream on this machine. The in-tree 1296x972 and 2592x1944 mode tables were used. Raw captures from the ISYS video node (5 frames per stream), one module build with the patch and one without, each run from a cold boot with no gap between streams so that the sensor stayed powered (autosuspend delay is 1 s): - Without the patch: stream 1 (1296x972) delivered 5 frames; stream 2 (2592x1944) timed out with no data and the pipeline needed a reboot ("stream stop time out"). - With the patch: the sequence 1296x972, 2592x1944, 1296x972, 2592x1944 delivered 5 complete frames of the requested size on all four streams, with plausible image data in each. In both runs the CSI-2 receiver logs "Transfer FIFO overflow" and "Inter-frame packet discarded" errors at stream start; they appear on every stream on this machine and are not changed by the patch. The test scripts and this summary were prepared with an AI coding assistant (Claude); I ran the tests on my Surface Pro 8. Tested-by: technosf <technosf@hit-on.com> ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start 2026-10-29 9:27 ` [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start Marco Ziliani 2026-10-29 16:56 ` Chris Simpson 2026-11-03 21:01 ` technosf @ 2026-11-20 9:37 ` Sakari Ailus 2026-11-20 17:28 ` Marco Ziliani 2 siblings, 1 reply; 8+ messages in thread From: Sakari Ailus @ 2026-11-20 9:37 UTC (permalink / raw) To: Marco Ziliani Cc: Daniel Scally, Mauro Carvalho Chehab, linux-media, Chris Simpson, Tony Garcia, Simon Kruse, D. Manresa, linux-kernel Hi Marco, On Thu, Oct 29, 2026 at 10:27:52AM +0100, Marco Ziliani wrote: > ov5693_mode_configure() is only called from the runtime PM resume path, > through ov5693_sensor_init(). If the sensor stays powered between two > streams with different modes, the settings for the second mode are never > written to the hardware. > > Move the call from ov5693_sensor_init() to ov5693_s_stream(), before the > controls are applied, so that the mode is written on every stream start. > > Fixes: 89aef879cb53 ("media: i2c: Add support for ov5693 sensor") > Link: https://github.com/linux-surface/kernel/pull/181 > Signed-off-by: Marco Ziliani <rylos78@gmail.com> > --- > drivers/media/i2c/ov5693.c | 18 +++++++++++++----- > 1 file changed, 13 insertions(+), 5 deletions(-) > > diff --git a/drivers/media/i2c/ov5693.c b/drivers/media/i2c/ov5693.c > index 56599f9ca..d09095c3e 100644 > --- a/drivers/media/i2c/ov5693.c > +++ b/drivers/media/i2c/ov5693.c > @@ -663,11 +663,6 @@ static int ov5693_sensor_init(struct ov5693_device *ov5693) > return dev_err_probe(ov5693->dev, ret, > "global settings error\n"); > > - ret = ov5693_mode_configure(ov5693); > - if (ret) > - return dev_err_probe(ov5693->dev, ret, > - "mode configure error\n"); > - > ret = ov5693_enable_streaming(ov5693, false); > if (ret) > dev_err(ov5693->dev, "stop streaming error\n"); > @@ -1000,6 +995,19 @@ static int ov5693_s_stream(struct v4l2_subdev *sd, int enable) > return ret; > > mutex_lock(&ov5693->lock); > + > + /* > + * Program the mode on every stream start, so that a format > + * change also reaches a sensor that stayed powered since the > + * previous stream, and before the controls so that the mode > + * registers don't clobber them. > + */ This doesn't seem quite right. The static register list should be written on power-on and the rest when they change. Also there shouldn't be overlap between the register list and the registers programmatically determined by the driver. > + ret = ov5693_mode_configure(ov5693); > + if (ret) { > + mutex_unlock(&ov5693->lock); > + goto err_power_down; > + } > + > ret = __v4l2_ctrl_handler_setup(&ov5693->ctrls.handler); > if (ret) { > mutex_unlock(&ov5693->lock); > -- Regards, Sakari Ailus ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start 2026-11-20 9:37 ` Sakari Ailus @ 2026-11-20 17:28 ` Marco Ziliani 0 siblings, 0 replies; 8+ messages in thread From: Marco Ziliani @ 2026-11-20 17:28 UTC (permalink / raw) To: Sakari Ailus Cc: Daniel Scally, Mauro Carvalho Chehab, linux-media, Chris Simpson, Tony Garcia, Simon Kruse, D . Manresa, linux-kernel Hi Sakari, Thanks for the review. On Fri, Nov 20, 2026 at 11:37:10AM +0200, Sakari Ailus wrote: > This doesn't seem quite right. The static register list should be written > on power-on and the rest when they change. Also there shouldn't be overlap > between the register list and the registers programmatically determined by > the driver. There are three such overlaps in ov5693_global_regs today: 0x3820 and 0x3821 (FORMAT1/FORMAT2, whose binning and flip bits the driver sets from the format and the flip controls) and 0x350b (the low byte of the analogue gain). They predate this series, but I'll fix them in v3 with a separate patch: drop 0x350b from the list, and let the driver program 0x3820/0x3821 whole, including the bits it doesn't manage today. For the rest, I'd keep writing the mode registers on power-on as before, and also write them from set_fmt() and set_selection() on the active state when the sensor is powered, instead of on every stream start. That needs pm_runtime_get_if_active() rather than the pm_runtime_get_if_in_use() the controls use, so that a change made during the autosuspend delay is written too. It fixes the same bug: today a format change made while the sensor stays powered never reaches the hardware. Does that match what you had in mind? Thanks, Marco ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2 2/3] media: i2c: ov5693: Keep the Bayer order when flipping at full resolution 2026-10-29 9:27 [PATCH v2 0/3] media: i2c: ov5693: Fix mode changes, flips and autosuspend Marco Ziliani 2026-10-29 9:27 ` [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start Marco Ziliani @ 2026-10-29 9:27 ` Marco Ziliani 2026-10-29 9:27 ` [PATCH v2 3/3] media: i2c: ov5693: Use autosuspend when stopping the stream Marco Ziliani 2 siblings, 0 replies; 8+ messages in thread From: Marco Ziliani @ 2026-10-29 9:27 UTC (permalink / raw) To: Daniel Scally, Sakari Ailus, Mauro Carvalho Chehab Cc: linux-media, Chris Simpson, Tony Garcia, Simon Kruse, D. Manresa, linux-kernel, Marco Ziliani In the full (unbinned) readout each of the horizontal and vertical flips moves the Bayer phase by one column. With exactly one flip enabled the CSI-2 receiver gets GBRG instead of the SBGGR10 the driver reports, which gives a magenta and green image; with both enabled the two shifts cancel out. The crop start is only honoured in steps of two pixels, so compensate by shifting the output window by one column when hflip XOR vflip, and widen the crop by two columns, within the pixel array, so that the window still fits. Reprogram the window when either flip changes. The binned readout is left unchanged. With this change, raw 2592x1944 frames come out BGGR at all four hflip/vflip settings on the Surface Pro 5 (IPU3); the same change in the linux-surface tree gave BGGR at all four settings on a Surface Pro 7 (IPU4P) and a Surface Pro 9 (IPU6). Without it, the order is only right with both flips off or both on. Fixes: 89aef879cb53 ("media: i2c: Add support for ov5693 sensor") Link: https://github.com/linux-surface/kernel/pull/181 Tested-by: Chris Simpson <chris@nilk.net> Tested-by: Tony Garcia <tony@loafecho.com> Signed-off-by: Marco Ziliani <rylos78@gmail.com> --- drivers/media/i2c/ov5693.c | 56 +++++++++++++++++++++++++++++++++++++++------- 1 file changed, 48 insertions(+), 8 deletions(-) diff --git a/drivers/media/i2c/ov5693.c b/drivers/media/i2c/ov5693.c index d09095c3e..9fedc087e 100644 --- a/drivers/media/i2c/ov5693.c +++ b/drivers/media/i2c/ov5693.c @@ -361,6 +361,49 @@ static const u8 ov5693_test_pattern_bits[] = { /* V4L2 Controls Functions */ +/* + * In the full (unbinned) readout each flip moves the Bayer phase by one + * column, so with exactly one of them enabled the CSI-2 receiver gets GBRG + * instead of the SBGGR10 the driver reports; with both enabled the two shifts + * cancel out. The crop start is only honoured in steps of two pixels, so + * compensate by shifting the output window by one column instead, and widen + * the crop so that the window still fits. + */ +static bool ov5693_bayer_shift(struct ov5693_device *ov5693) +{ + const struct ov5693_mode *mode = &ov5693->mode; + bool hflip, vflip; + + if (mode->binning_x || mode->binning_y) + return false; + + hflip = ov5693->ctrls.hflip && ov5693->ctrls.hflip->val; + vflip = ov5693->ctrls.vflip && ov5693->ctrls.vflip->val; + + return hflip ^ vflip; +} + +static int ov5693_window_x_configure(struct ov5693_device *ov5693) +{ + const struct ov5693_mode *mode = &ov5693->mode; + bool shift = ov5693_bayer_shift(ov5693); + u32 crop_end = mode->crop.left + mode->crop.width; + int ret = 0; + + /* Widen the crop for the shifted window, within the pixel array */ + if (shift) + crop_end = min(crop_end + 2, + max_t(u32, crop_end, OV5693_NATIVE_WIDTH - 1)); + + /* Offset X */ + cci_write(ov5693->regmap, OV5693_OFFSET_START_X_REG, shift, &ret); + + /* Crop End X */ + cci_write(ov5693->regmap, OV5693_CROP_END_X_REG, crop_end, &ret); + + return ret; +} + static int ov5693_flip_vert_configure(struct ov5693_device *ov5693, bool enable) { @@ -373,7 +416,7 @@ static int ov5693_flip_vert_configure(struct ov5693_device *ov5693, if (ret) return ret; - return 0; + return ov5693_window_x_configure(ov5693); } static int ov5693_flip_horz_configure(struct ov5693_device *ov5693, @@ -388,7 +431,7 @@ static int ov5693_flip_horz_configure(struct ov5693_device *ov5693, if (ret) return ret; - return 0; + return ov5693_window_x_configure(ov5693); } static int ov5693_get_exposure(struct ov5693_device *ov5693, s32 *value) @@ -566,16 +609,13 @@ static int ov5693_mode_configure(struct ov5693_device *ov5693) cci_write(ov5693->regmap, OV5693_CROP_START_X_REG, mode->crop.left, &ret); - /* Offset X */ - cci_write(ov5693->regmap, OV5693_OFFSET_START_X_REG, 0, &ret); - /* Output Size X */ cci_write(ov5693->regmap, OV5693_OUTPUT_SIZE_X_REG, mode->format.width, &ret); - /* Crop End X */ - cci_write(ov5693->regmap, OV5693_CROP_END_X_REG, - mode->crop.left + mode->crop.width, &ret); + /* Offset X and Crop End X follow the flips, see ov5693_bayer_shift() */ + if (!ret) + ret = ov5693_window_x_configure(ov5693); /* Horizontal Total Size */ cci_write(ov5693->regmap, OV5693_TIMING_HTS_REG, OV5693_FIXED_PPL, -- 2.56.0 ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v2 3/3] media: i2c: ov5693: Use autosuspend when stopping the stream 2026-10-29 9:27 [PATCH v2 0/3] media: i2c: ov5693: Fix mode changes, flips and autosuspend Marco Ziliani 2026-10-29 9:27 ` [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start Marco Ziliani 2026-10-29 9:27 ` [PATCH v2 2/3] media: i2c: ov5693: Keep the Bayer order when flipping at full resolution Marco Ziliani @ 2026-10-29 9:27 ` Marco Ziliani 2 siblings, 0 replies; 8+ messages in thread From: Marco Ziliani @ 2026-10-29 9:27 UTC (permalink / raw) To: Daniel Scally, Sakari Ailus, Mauro Carvalho Chehab Cc: linux-media, Chris Simpson, Tony Garcia, Simon Kruse, D. Manresa, linux-kernel, Marco Ziliani The driver enables runtime PM autosuspend with a 1 second delay at probe, but drops the usage count at stream stop with pm_runtime_put(), which doesn't update the device's last busy time. The autosuspend delay is then counted from the runtime resume at stream start rather than from stream stop, so after any stream longer than the delay the sensor is powered off right away. Use pm_runtime_put_autosuspend(), which marks the device busy, so that the delay counts from stream stop as intended, and a following stream started within it doesn't power the sensor up from scratch again. With the mode now programmed on every stream start, keeping the sensor powered between streams no longer leaves it in a stale mode. On a Surface Pro 9 (IPU6) with autosuspend_delay_ms set to 3000, the sensor suspended 1-2 ms after a 5 s stream stopped; with this change, 3.7 s after it, i.e. the delay plus the autosuspend timer slack. On a Surface Pro 5 (IPU3) with the default 1 s delay, the sensor suspended as soon as a 2 s stream stopped; with this change, 1.1 s after it. Fixes: 89aef879cb53 ("media: i2c: Add support for ov5693 sensor") Reported-by: D. Manresa <dmanresa@gmail.com> Closes: https://github.com/linux-surface/kernel/pull/181#issuecomment-6436016335 Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com> Tested-by: Chris Simpson <chris@nilk.net> Tested-by: Tony Garcia <tony@loafecho.com> Signed-off-by: Marco Ziliani <rylos78@gmail.com> --- drivers/media/i2c/ov5693.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/i2c/ov5693.c b/drivers/media/i2c/ov5693.c index 9fedc087e..086f9df07 100644 --- a/drivers/media/i2c/ov5693.c +++ b/drivers/media/i2c/ov5693.c @@ -1065,7 +1065,7 @@ static int ov5693_s_stream(struct v4l2_subdev *sd, int enable) goto err_power_down; if (!enable) - pm_runtime_put(ov5693->dev); + pm_runtime_put_autosuspend(ov5693->dev); return 0; err_power_down: -- 2.56.0 ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2026-11-20 17:28 UTC | newest] Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2026-10-29 9:27 [PATCH v2 0/3] media: i2c: ov5693: Fix mode changes, flips and autosuspend Marco Ziliani 2026-10-29 9:27 ` [PATCH v2 1/3] media: i2c: ov5693: Program the mode registers on stream start Marco Ziliani 2026-10-29 16:56 ` Chris Simpson 2026-11-03 21:01 ` technosf 2026-11-20 9:37 ` Sakari Ailus 2026-11-20 17:28 ` Marco Ziliani 2026-10-29 9:27 ` [PATCH v2 2/3] media: i2c: ov5693: Keep the Bayer order when flipping at full resolution Marco Ziliani 2026-10-29 9:27 ` [PATCH v2 3/3] media: i2c: ov5693: Use autosuspend when stopping the stream Marco Ziliani
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®