From: Jonathan Cameron <jic23@kernel.org>
To: Nicolae-Daniel Deaconescu <Nicolae-daniel.Deaconescu@analog.com>
Cc: "Uwe Kleine-König" <ukleinek@kernel.org>,
"Conor Dooley" <conor+dt@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
"Rob Herring" <robh@kernel.org>,
"David Lechner" <dlechner@baylibre.com>,
"Nuno Sá" <nuno.sa@analog.com>,
"Andy Shevchenko" <andy@kernel.org>,
"Michael Hennerich" <michael.hennerich@analog.com>,
"Trevor Gamblin" <tgamblin@baylibre.com>,
"Joshua Crofts" <crofts@kernel.org>,
"Sergiu Cuciurean" <sergiu.cuciurean@analog.com>,
linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
linux-pwm@vger.kernel.org, linux-doc@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v4 4/6] iio: adc: ad7625: move initial mode setup
Date: Sat, 21 Nov 2026 23:40:15 +0000 [thread overview]
Message-ID: <20261121234015.6cbb4bef@jic23-hlaptop> (raw)
In-Reply-To: <20261119112437.197306-5-Nicolae-daniel.Deaconescu@analog.com>
On Thu, 19 Nov 2026 13:24:18 +0200
Nicolae-Daniel Deaconescu <Nicolae-daniel.Deaconescu@analog.com> wrote:
Rather than move, I'd say 'factor out' for the title and in this text.
> Move the EN pin mode setup from ad7625_probe() into
> ad7625_set_initial_mode(). Pick the mode first and check the result of
> setting it once, returning its error instead of -EINVAL. A following patch
It was only ever set once. Anyhow the only bit of this paragraph I'd
keep is. "Return error if reported by ad7960_set_mode() rather than
replacing it with -EINVAL"
> adds parts without EN pins that skip it.
This last bit is fine but I'd put it first as the 'why' answer for the
whole patch.
>
> Signed-off-by: Nicolae-Daniel Deaconescu <Nicolae-daniel.Deaconescu@analog.com>
> ---
> drivers/iio/adc/ad7625.c | 52 ++++++++++++++++++++++------------------
> 1 file changed, 29 insertions(+), 23 deletions(-)
>
> diff --git a/drivers/iio/adc/ad7625.c b/drivers/iio/adc/ad7625.c
> index ade2f2368bd8..127441050687 100644
> --- a/drivers/iio/adc/ad7625.c
> +++ b/drivers/iio/adc/ad7625.c
> @@ -561,6 +561,32 @@ static int devm_ad7625_regulator_setup(struct device *dev,
> return 0;
> }
>
> +static int ad7625_set_initial_mode(struct device *dev, struct ad7625_state *st)
> +{
> + enum ad7960_mode mode;
> + int ret;
> +
> + /* Set the device mode based on detected EN configuration. */
> + if (!st->info->has_bandwidth_control) {
> + ad7625_set_en_gpios_for_vref(st, st->have_refin, st->vref_mv);
> + return 0;
> + }
> +
> + if (st->can_wide_bandwidth)
> + mode = AD7960_MODE_WIDE_BANDWIDTH;
> + else if (st->can_narrow_bandwidth)
> + mode = AD7960_MODE_NARROW_BANDWIDTH;
> + else
> + return dev_err_probe(dev, -EINVAL,
> + "couldn't set device to wide or narrow bandwidth modes\n");
> +
> + ret = ad7960_set_mode(st, mode, st->have_refin, st->vref_mv);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to set EN pins\n");
> +
> + return 0;
> +}
> +
> static int ad7625_probe(struct platform_device *pdev)
> {
> struct device *dev = &pdev->dev;
> @@ -595,29 +621,9 @@ static int ad7625_probe(struct platform_device *pdev)
> if (ret)
> return ret;
>
> - /* Set the device mode based on detected EN configuration. */
> - if (!st->info->has_bandwidth_control) {
> - ad7625_set_en_gpios_for_vref(st, st->have_refin, st->vref_mv);
> - } else {
> - /*
> - * If neither sampling mode is available, then report an error,
> - * since the other modes are not useful defaults.
> - */
> - if (st->can_wide_bandwidth) {
> - ret = ad7960_set_mode(st, AD7960_MODE_WIDE_BANDWIDTH,
> - st->have_refin, st->vref_mv);
> - } else if (st->can_narrow_bandwidth) {
> - ret = ad7960_set_mode(st, AD7960_MODE_NARROW_BANDWIDTH,
> - st->have_refin, st->vref_mv);
> - } else {
> - return dev_err_probe(dev, -EINVAL,
> - "couldn't set device to wide or narrow bandwidth modes\n");
> - }
> -
> - if (ret)
> - return dev_err_probe(dev, -EINVAL,
> - "failed to set EN pins\n");
> - }
> + ret = ad7625_set_initial_mode(dev, st);
> + if (ret)
> + return ret;
>
> ret = devm_ad7625_pwm_get(dev, st);
> if (ret)
next prev parent reply other threads:[~2026-11-21 23:40 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-19 11:24 [PATCH v4 0/6] iio: adc: ad7625: add LTC2387 and ADAQ2387x support Nicolae-Daniel Deaconescu
2026-11-19 11:24 ` [PATCH v4 1/6] pwm: core: add pwm_get_waveform_step_might_sleep() Nicolae-Daniel Deaconescu
2026-11-21 23:35 ` Jonathan Cameron
2026-11-19 11:24 ` [PATCH v4 2/6] pwm: axi-pwmgen: report the waveform step Nicolae-Daniel Deaconescu
2026-11-19 11:24 ` [PATCH v4 3/6] iio: adc: ad7625: fix sampling frequency handling Nicolae-Daniel Deaconescu
2026-11-19 11:24 ` [PATCH v4 4/6] iio: adc: ad7625: move initial mode setup Nicolae-Daniel Deaconescu
2026-11-21 23:40 ` Jonathan Cameron [this message]
2026-11-19 11:24 ` [PATCH v4 5/6] dt-bindings: iio: adc: add adi,ltc2387 Nicolae-Daniel Deaconescu
2026-11-19 11:24 ` [PATCH v4 6/6] iio: adc: ad7625: add LTC2387 and ADAQ2387x support Nicolae-Daniel Deaconescu
2026-11-21 23:48 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261121234015.6cbb4bef@jic23-hlaptop \
--to=jic23@kernel.org \
--cc=Nicolae-daniel.Deaconescu@analog.com \
--cc=andy@kernel.org \
--cc=conor+dt@kernel.org \
--cc=crofts@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dlechner@baylibre.com \
--cc=krzk+dt@kernel.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pwm@vger.kernel.org \
--cc=michael.hennerich@analog.com \
--cc=nuno.sa@analog.com \
--cc=robh@kernel.org \
--cc=sergiu.cuciurean@analog.com \
--cc=tgamblin@baylibre.com \
--cc=ukleinek@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®